Search Documents

By E Drueppel, F M. Meyer, P N. Martens, J P

The present study shows a calculation of the amount of copper contained in the initial reserves that remains un-extracted. The study is based on data of 271 producing copper mines and includes geological parameters, mining methods used and the processing recovery. Estimations disclose that approximately 25 per cent of the metal contained in the original reserves is not extracted. One third of this value can be attributed to mining, whereas two thirds are related to processing. However, values differ for different ore deposit types and mining districts.

Jan 1, 2003

The successful operation of diesel equipment underground does not entirely depend on selection of robust, reliable, easily maintained machines. Results are also heavily influenced by the following factors: Design and condition of the operating area. Skill of operators. Correct maintenance facilities. Experience, skill and initiative of maintenance personnel. If the mine layout does not allow access to a central workshop area, the effect of any shortcomings will be magnified. The best results will only be obtained by close co-operation between mining and maintenance departments right from the initial planning stages.

Jan 1, 1977

Mine planning for ore recovery by open stoping and pillar recovery is becoming more sophisticated, but there are basic operating constraints which must be imposed if this planning is to realise the production results on which the mine is dependant. The production reliability of an open stope is usually a high priority and common design problems can be identified. A range of practical considerations which should be considered at the mine planning stage are reviewed including equipment performance, blasting technology, ventilation requirements, development layouts, lead time, ground conditions, support, backfilling and ore recovery.

Jan 1, 1982

Alcoa of Australia Limited owns and operates a 150 MW power station adjacent to the coastal township of Anglesea in south western Victoria.The power station was constructed in the mid 1960s to supply electricity to the Company's smelter at Point Henry, near Geelong, and is fuelled by high quality brown coal mined at the site in Alcoa's lease area.The open cut mine, producing approximately one million tonnes of coal per year, utilises a backfilling method and has carried out progressive regeneration of those completed areas since the mid 1970s.

Jan 1, 1992

By Kurzeme M, Willoughby D. R

The current approach to the design of fill, as a structural component in a mining system, is based on traditional usage, previous experience, empirical rules and preconceived ideas. This approach does not permit the relative economicsof the various possibilities to be evaluated, retards introduction of new materials or processes, and results in fragmented fill research effort.A rational approach to the design of fill is proposed as a means of overcoming these disadvantages.This is based on five components:(a) statement of functions of fill,(b) definition of modes of fill response,(c) criteria of satisfactory performance,(d) analysis of fill response,(e) specification of required fill properties and methods of obtaining them.An assessment of each component indicates that the adoption of this rational design approach will require research effort in categorising modes of fill response and in defining criteria of satisfactory performance.

Jan 1, 1973

The development of computers is examined in the context of the mining industry. The risk element is given as a reason for the slow introduction of the computer into mining. Dealing with mining's uncertainty is seen as a major role for computers. The use of computers is traced from early accounting applications to current involvement with all aspects of mining. The problems associated with increasing use of computers and their impact on management is discussed in depth. Disenchantment of management is thought to arise from unfulfilled expectations. Contributory causes are given as overselling of computers, reaction against change, speed and growth of computer technology. The solution is seen to lie in a more dominant role for user management in the development of computer systems and greater emphasis on education. The computer of the future will then become integral to the mining process as an extension of management's planning and control function.

Jan 1, 1974

By Ruffles B. R

A computer simulation has been developed to model the flow of copper ore in Isa Mine. It simulates extraction of copper ore from the 1100 orebody by load-haul-dump (LHD) units to ore passes, haulage from chutes on 19 level by Rockflo trains to crusher bins, crushing and hoisting. It can assess in terms of the tonnage and head grade of ore hoisted, the effect of varying operating strategies, as well as measur- ing shortfalls in required capacities of any of the operations (extraction, hauling, crushing and hoisting). The simulation was designed as a modular, deterministic, steady-state model with parameter input allowing complete flexibility in its use. Queuing theory is used extensively to evaluate the effect of interference at potential bottlenecks. The model has been used to determine the effect on production of varying train sizes, maintenance policies on the haulage circuit, orepass capacities, and extraction operations.

Jan 1, 1974

The hazard posed by underground mine fires is illustrated in the first part of this paper by means of a review of experiences in four mining countries over the last three decades. This brief review indicates that while much progress has been made generally in preventing fires and providing means of protection to miners, the possibility of disasters occurring must continue to be regarded as very real. Based upon recent investigations by the South African mining industry, an integrated strategy for providing protection to personnel in the event of a fire is outlined in the second part of the paper. The main, complementary, elements in this strategy are the prevention of ignitions, the limitation of fires, provision of protection systems and equipment, training for emergencies, and effective implementation of safety measures. Some comments are made on important aspects of these elements and on possible further developments.

Jan 1, 1988

North Flinders Mines Limited (N.F.M.) is an Australian-owned mineral exploration and mining company based in South Australia. In the 1970's it researched the prospectiveness of the Tanami (central western region of the N.T.) for the identification of possible economic gold deposits. Having outlined the potential for such a deposit at The Granites (550 km. N.W. of Alice Springs), it marked out and in 1975 applied for the grant of eleven gold mining leases (G.M.L.'s) under the provisions of the then Mining Ordinance. This application was deferred by the Commonwealth Government during the time of the Aboriginal Land Rights Commission (Woodward), subsequent enactment of legislation and land claims. In 1980, the Walpiri and Kartangarurra-Kurintji land claim encompassing the G.M.L.'s, became Aboriginal land. It therefore became necessary for N.F.M. to negotiate a mining agreement with the Central Land Council (C.L.C.) represent- ing the Traditional Owners, before the G.M.L.'s could be granted. In August 1983, the C.L.C. and N.F.M. concluded an agreement to enable the grant of mining interests necessary for the devel- opment of The Granites Gold Project. In several ways this agreement is unique in That:

Jan 1, 1984

By Aalbers J. P A

The State Electricity Commission of Victoria (SECV) operates 13 excavators, 3 travelling stackers and 4 mobile slew conveyors in their three open cuts in the Latrobe Valley. The majority of these machines have been designed and constructed to a German design code current at the date of order. The SECV has always ensured that the machines were manufactured and erected to the appropriate standards. The SECV has a policy of having all machines inspected by an independent inspector every two years. These inspections are based on those carried out in Germany. The inspections have been carried out by inspectors from Germany who have the necessary experience to do similar work in German open cuts. Major faults found during the inspections have been repaired, however,the gradual breakdown of corrosion protection system has continued. The structures on some machines have areas of bad corrosion. This, coupled with wear on major mechanical equipment, would require an extensive outage to overhaul the machines. Refurbishment of Hazelwood Power Station will result in higher levels of production and extended life for the station. This will require improvement in the total output from Morwell Open Cut (MOC). To meet this increased coal demand, the open cut equipment will need to operate more efficiently and for a longer period of life.

Jan 1, 1989

By Salehi M. R

Although inherent mineral matter appears to have no effect of the reflectivity of inertinite in the reflecting light microscope, it has a marked effect on the grey levels resulting from the backscattered electron response in the scanning electron microscope. Inertinite with a high inherent mineral matter content has a high grey level response but not as high as that of mineral matter. The highest grey level response is with inertodetrinite which at times could be mistaken for mineral matter. Fusinite has a higher grey level response than semi-fusinite. The backscattered electron grey level response corresponds to average atomic number and hence approximately to density. If a porous structure develops and becomes filled with mineral matter such as S, Cl, Ca, Si, and Al the grey level will be higher. Micrinite has an unusual response in that it behaves like an exinite maceral in the SEM rather than an inertinite maceral. It either has a low grey level when relatively free of inherent mineral matter, or a low grey level background with high level granules corresponding to Si and Al dominantly. Similar structures have been found in exsudatinite and resinite. It is thought that micrinite results from the migration of hydrocarbons out of exinite giving a porous structure which usually accommodates inorganic matter.

Jan 1, 1991

By Henderson J

Iron ore samples selected from the Deepdale, Iron Prince and Mt. Newman ore bodies have been pelletised on a pilot scale plant and subsequently reduced under laboratory conditions by hydrogen or carbon monoxide. Pellets approximately 1 cm in diameter have been reduced by hydrogen over the temperature range 5000- 900¦C and the results examined by thermogravimetric, microscopic, electron probe and x-ray techniques. After an initial time delay it was found that up to 95% reduction the rate of reduction could be described by a transport con- trolled porous model, in which the effective diffusivities of hydrogen in theòpr¦duct layer and the reaction zone are filar. Independent measurements of effective diffusivity supported the values obtained from the reduction data. ve 95% reduction the rate decreased markedly due to the formation_of retained wustite or fayalite. Comparison with reduction by carbon monoxide over the temperature range 7500 - 900¦C showed that the rate eduction by carbon monoxide was approximately five times slower than the rate by hydrogen. The rate of reduction was found to be a function of the properties of the pellets, which may account for the ely conflicting results that have been obtained in previous investigation on porous pellets.

Jan 1, 1970

This paper presents a review of heat illness in mining, including reference to several recent investigations by the author. Heat illness is a collective term, covering the conditions of heat stroke, heat exhaustion, heat cramps and miliaria rubra. Heat stroke is life-threatening and is by far the most serious condition. It is rare in mining, if appropriate control measures are instituted. Heat exhaustion is primarily due to hypohydration, following prolonged sweating in hot conditions. Symptoms include fatigue, headaches, dizziness, anorexia, nausea, vomiting, shortness of breath, or brief syncope. Confusion, ataxia, prolonged unconsciousness or convulsions are strongly suggestive of heat stroke. Heat cramps are painful involuntary contractions of skeletal muscle associated with work in hot conditions. The limbs are usually involved and the spasms typically last a few minutes, during which the affected part of the body is incapacitated. Heat cramps tend to occur in heat exhaustion, when hypohydration becomes marked. Miliaria rubra is a skin rash caused by extravasation of sweat into the skin, as a result of obstruction of the sweat glands. It occurs after prolonged and profuse sweating in hot environments. It can take three to four weeks of sedentary duties, in an air-conditioned surface environment, for the condition to resolve. Heat illness would be unlikely in underground mining, if the thermal environment was sufficiently well controlled by ventilation and refrigeration. This is however, often not practicable. Where engineering controls alone cannot provide sufficient control of risk, the residual risk can be assessed using an appropriate heat stress index. While procedural controls may further reduce the residual risk, it is important to remember that these are less reliable than engineering controls and cases of heat illness may still occur. Procedural controls include the application of heat stress limits, education, hydration, self-pacing, early symptom reporting, medical advice, acclimatisation procedures, air conditioned accommodation, support to achieve a healthy body mass index, and an effective emergency response capacity.

Jan 1, 2005

In general the iron ore industry has been slow to adopt the Whittle Pit optimising software in the evaluation of iron ore deposits. The reasons for this are two-fold:the iron ore industry has developed techniques, usually bespoke software residing in the corporate offices of the respective iron ore companies, to establish their final pit limits; and the fact that the Whittle software doesnÆt easily lend itself to estimating a sales product of constant quality without maximising grade (metal content). The Whittle software is based on the work done by Lerch and Grossman (in the early 1970s), which proposed that graph theory be used to establish an optimal surface that maximises the revenue from a deposit. The maximised surface created in the pit optimiser is translated into a proposed optimal final pit shape that can be used by the mine design engineers as a target outline to lay out the final practical pit. By treating a geological and ore resources model that was created for an iron ore deposit as a subset of the recoverable resources estimation (RRE) type of geological models, the evaluation of an iron ore deposit and establishing the final pit is greatly simplified in the Whittle 4-X optimiser. Instead of trying to optimise the iron content of the deposit, the emphasis swings to maximising the extraction of a finished and saleable iron ore product. This is achieved by treating the finished saleable iron ore as an element in the multi-element Whittle optimiser. The quality of the finished sales product is represented, and the material that cannot be used in the blended product is also shown. Proposals for enhancing the functionality in the Whittle 4-X optimiser to make the evaluation of iron (and coal) deposits easier includes the creation of a new reporting function that will allow the user to specify which field(s) can be used as the divisor(s) for the reporting of the element grades in the model.

Jan 1, 2007

By Bojcevski D

The deportment and textural relationships of silver bearing phases are key characteristics in understanding the behaviour of silver ores in flotation tests or processing plants. These characteristics are however difficult to define and quantif

Jan 1, 1997

This paper will present a series of examples drawn for a number of Australian and international mining companies showing their recent attempts at optimisation of capital. The results will be compared, contrasted and discussed in the light of six factors that are considered crucial to any analysis of this subject. The factors are: ò the market availability of capital ò the corporate strategy and performance ò the capital structure appropriate to the corporate positioning within the industry ò the parties to the optimisation equation ò the measurement of success of optimisation The factors above are not mutually exclusive and are generally interdependent so their order above is of little consequence. Other papers presented at this conference will dwell in more depth on all these factors, therefore this paper shall focus only on the key elements of each factor. By way of summary this paper will also address the issue of the longevity of optimisation - is it temporary or long term.

Jan 1, 1991

The metallurgical works of the Electrolytic Zinc Company is situated on the Derwent Estuary, approximately five miles north of the city of Hobart and near a relatively dense housing area. Zinc concentrates, consisting chiefly of zinc and sulphur, have been roasted at Risdon for 53 years;- recently at rates of 1, 100 tons per day. The zinc content of the ores is converted to zinc calcine (ZnO), which is a dusty material. The calcine is leached with acid to form zinc sulphate, which is then electrolysed to make zinc. The sulphur is oxidised during roasting to sulphur dioxide, part of which is converted to sulphuric acid and part is dissolved in estuarine water which is then discharged to the Derwent Estuary. Photographic slides were exhibited showing the unaffected green flora of the nearby hills, of clear exit stacks, of green lawns, and of a w ll lrcnt nines hnlP anlf nniir.qa within the Wnrka hnnnrla_rv_

Jan 1, 1971

Australia had been enjoying a market boom led by the mining sector and West Australian mines were leading the way to satisfy the massive demand for our natural resources, especially from China. However, the Apache gas explosion on Varanus Island, 97 km off the west coast, has clearly demonstrated how the unexpected can suddenly impact on profitability and investor confidence for the mining industry. Risk management with contingency planning can provide the most cost-effective solution to help ensure mining projects are successful. For this discussion we will focus primarily on contingency planning, CP for mining projects à and how to plan for the unexpected. The Apache gas explosion will be our example æUnexpected EventÆ. Insurance may provide financial compensation but it will not protect your reputation as a reliable supplier or prevent damage to investor confidence and future mine projects. However, contingency planning can provide real protection for mining projects à to survive the unexpected.

Jan 1, 2009

The outcome of future metallogenic research will be important to everyone because it will. have a profound impact on our ability to find new deposits of non-reservable mineral resources. Failure to replenish our mineral stocks will threaten man's economic and social well-being, and it is vital that future directions of metallogenic research are considered carefully to ensure that research funds are applied wisely to underwrite our future.Today we are witnessing the declining phase of the era of easy exploration. The rate of discovery of shallow orebodies is slowing. This is very evident for base-metal deposits but is becoming increasingly apparent for gold deposits. The easy exploration era was marked by a heavy reliance on exploration techniques capable of directly detecting mineralization. These include simple prospecting methods as well as a host of geochemical and geophysical procedures and tools that enable explorers to pin-point regions' of mineralization within the upper couple of hundred metres of the Earth's crust. The role of

Jan 1, 1990

Courses in chemical engineering and metallurgical engineering at the University of Queensland were compared and the main difference was found to be the greater emphasis on the application of chemical engineering fundamentals, particularly chemical thermodynamics, to specific processes in the metallurgy course. This reflects the distinctive features of extractive metallurgical processes which are not common in other chemical engineering processes and which justify the study of extractive metallurgy in its own right. B.Sc. courses in metallurgy provide one way in which the specialist knowledge of extractive metallurgy can be taught. General metallurgy courses are considered to be preferable to those restricted solely to extractive metallurgy since graduates of a general course have a wider choice of employment, while excessive emphasis on extractive metallurgical applications in chemical engineering courses could reduce the non-specific nature of these courses. Postgraduate diploma and higher degree programmes are avenues for non- metallurgists to acquire knowledge of the discipline.

Jan 1, 1984