Search Documents

By Linda C. M. Elliot, Liangxue Liu

"The deposition of tailings under water is considered to be one of the most environmentally promising and potentially cost effective methods to reduce or eliminate acid mine drainage from tailings. One of the concerns of subaqueous deposition has been that metals may leach into the cover waters, thereby increasing aqueous metal concentrations to higher than acceptable limits. This potential was seen to have an even greater possibility for impact when the tailings are deposited under acidic lake water.The following paper summarizes the results of subaqueous tailings pilot column test work conducted to determine the effects of subaqueously deposited tailings on lake water and tailings pore water. Two types of tailings were tested: high sulphide tailings (pyrrhotite concentrate), and low sulphide tailings (end of pipe slime tailings).Data was collected from five columns over a 13 month test period. The results indicated that a stagnant I 000 mm water cover was capable of maintaining the underlying tailings in a reducing condition. The upwards diffusion of pore water resulted in a pH increase in the waters overlying the thickened pyrrhotite tailings and the pyrrhotite tailings with a shallow cover of substrate. A conductivity gradient between the tailings and the water cover caused a diffusion of salts upwards into the overlying water column. Precipitation noted at the tailings water interface may be related to the precipitation of ferric oxyhydroxides, which resulted in a decrease in Fe concentrations noted in the water cover. Other metal concentrations did not exhibit significant increases in the water cover. A sulphate concentration gradient between the tailings and the water cover may have caused the diffusion of SQ4 from the tailings into the water cover."

Jan 1, 1997

By M. K. Gangal, M. A. Stoakes, A. E. Hall

"The major features of the CANMET thermodynamic mine ventilation network program, developed by the Mining and Mineral Process Engineering Department of the University of British Columbia for the Canada Centre for Mineral and Energy Technology (CANMET), are described.The program is designed for use by deep Canadian mines in planning ventilation flows where the effects of auto-compression of air, moisture lift work and natural ventilation are significant. Routines to simulate stalled fans and give an optional cost printout have been included in the program.A supplementary plotting program used to simplify data interpretation is also described.The program is described with a test data example of a deep mine. It is a valuable analytical tool which can assist ventilation engineers to simulate many alternative ventilation strategies at a low cost in a very short time.IntroductionCanadian underground mines are becoming deeper and more extensive. The use of more and larger diesel-powered equipment increases the amount of air required to be circulated in these complex systems. These effects, coupled with the increasing unit cost of the energy required for mine ventilation, require that the air is used with maximum efficiency.Optimum airflow distribution can be obtained by using network computer programs enabling engineers to plan future ventilation systems based on quantitative assessments. The programs used for deep mines must make allowance for the change of air density with depth, as the assumption of incompressible flow leads to serious errors. Natural ventilation effects may vary with depth and from part to part of the mine; this must be catered for by the program. The air moisture content changes throughout the circuit and a significant portion of the fan work may be used in removing moisture from the mine; as this work varies directly with the flow, a suitable relationship must be utilized in the program."

Jan 1, 1982

By J. L. Jambor, R. W. Boyle

"The Magnet Cove barite-sulphide deposit is a raking pipe-like body that replaced and partly filled a large brecciated zone at the junction of two faults at the contact between sedimentary rocks of the Horton and Windsor Groups of Mississippian age. The principal minerals in the deposit are siderite, barite, hematite, pyrite, marcasite, galena, sphalerite, chalcopyrite, tennantite, proustite, pearceite, acanthite and stromeyerite. The mineral assemblage and textural relationships indicate that the minerals were deposited from low-temperature solutions. The source of the elements in the deposit is believed to be the enclosing sedimentary rocks, with connate or ground waters as the transporting medium, and solubility products as the governing factor controlling the abundance and order of deposition of the minerals."

Jan 1, 1966

By H. R. Huffman

"This paper reviews the history of iron powder production, and outlines the varions production methods. The uses of iron powder and the reasons for its use are also covered. The paper concludes with a look at future trends in powder metallurgy.INTRODUCTION TO POWDERSTHE IRON POWDER INDUSTRY is enjoying a very rapid growth. The annual consumption of iron powder is now at the 100,000-ton level, twenty times higher than it was at the end of World War II, and the yearly in-crease bas been almost consistent at 20 per cent. This is expected to increase, bringing the tonnage to 200,-000, or even (according to some experts) to 270,000, in 1970. In any event, powder metallurgy is expanding at high speed and making an important impact on the production of iron and steel products. Some indication of the faith in the future market may be indicated by the commencement of three new powder production plants in Canada with a total capacity of 136,000 tons annually."

Jan 1, 1969

By W. N. Wallinger

The mine and concentrator of Cyprus Anvil Mining Corporation are situated in south-central Yukon, some 120 miles north of Whitehorse. The large lead-zinc concentrator employs conventional crushing and grinding , followed by differential flotation, to produce selective lead and zinc concentrates, as well as a mixed lead-zinc (bulk) concentrate. Since the commencement of operations in 1969, the concentrator has undergone expansions and modifications which have increased the capacity to 10,000 tons per day, and afforded some metallurgical improvements.

Jan 1, 1978

By M. Maldonado

This work details the application of a decentralized control strategy to a pilot flotation column working with a two-phase system (water-air). The process is represented by a multivariable system composed of three inputs and three outputs. The selected control variables are the froth depth, the air hold-up and the bias rate, whereas the corresponding manipulated variables are the set-points of the local flow controllers of tailings, air and wash water. All controlled variables are estimated using electrical conductivity based techniques. In particular, the results of a new method for estimating the bias rate, based on the measurement of the volumetric fraction of wash water under the interface, is presented. This method reduces the coupling problem associated to the bias estimation as a difference between feed and tailing water rates. Moreover, the nominal system transfer matrix can be represented by an upper triangular matrix, in such a way that the closed-loop system stability reduces to the stability of the independent control loops. The experimental results show that the closed-loop system performance, particularly that of the bias rate loop, is strongly dependent on the air flow rate, reaching in some cases the saturation point of the controller.

Jan 1, 2007

By A. C. Hitchins, C. N. Orssich

The Eagle zone is a gold-bearing, sheeted, quartz vein porphyry deposit hosted by the Cretaceous Dublin Gulch biotite granodiorite stock, located in central Yukon, 50 km north of Mayo. The deposit occurs at the western end of the stock and has been drill tested over a 1000 m by 500 m area, to a depth of 150m. Mineralization consists of 1 cm to 2 Cm wide, parallel, grey and white quartz veins with accessory gold, arsenopyrite, pyrite, pyrrhotite, chalcopyrite, native bismuth, bismuthinite, and scheelite. Vein densities range from two to fifteen veins per metre and average approximately five per metre. The majority of the veins have potassic and or phyllic alteration envelopes. Alteration of the granodiorite becomes pervasive as vein densities increase. Mineralization outside of the Eagle zone, but spatially related to the Dublin Gulch stock, includes: (i) scheelite bearing sheeted quartz vein zones within the east-central portion of the stock; (ii) a swarm of gold-bearing quartz-sulphide veins up to a metre wide in a zone along the northern contact of the stock and extending 7 km further west; (iii) the Mar scheelite skarn located on the south side of the stock; and (iv) cassiterite-bearing breccias located 2 km north of the stock. A geological potential resource of 64.5 Mt tonnes at a grade of 1.03 g/t Au has been estimated for the Eagle zone from widely spaced core and reverse circulation drill holes. Mineralization is open at depth, on strike to the west and beneath the hornfels to the north.

Jan 1, 1995

By A. C. A. Howe, J. C. Rowntree

"The Bernie Lake pegmatite near Lac Du Bonnet in southern Manitoba is a complexly zoned pegmatite containing several lithium-bearing units in addition to the western world's largest known reserve of cesium. The pegmatite forms a flat-lying ellipsoidal body within an east-west-trending Precambrian amphibolite. The pegmatite enclosed by this vertically schistose amphibolite lies near the eastern tip of a granitic intrusive. The relationship of this intrusive to the pegmatite is obscured by Bernie lake. To date, the pegmatite body has been delineated aver an area of approximately 80 acres; it attains a maximum thickness of 280 feet. Several distinct zones, including three assemblages of economic importance, comprise the pegmatite itself. The combined spodumene and lepidolite assemblages provide a recoverable defined lithium ore reserve of almost 5 million tons averaging more than 2 per cent lithium oxide. The recoverable cesium ore of the pollucite assemblage provides 300,000 tons averaging more than 20 per cent cesium oxide; this represents more than half of the western world's pollucite reserve. The Bernie Lake pegmatite deposit, owned by Chemalloy Minerals Limited, is well located with respect to the growing United States markets, and its reserves of cesium are large enough to enable it, under favourable economic circumstances, to become the major producer of this metal in North America."

Jan 1, 1967

By M. S. Badollet

INTRODUCTION THE DEMAND for general knowledge on asbestos fibres has increased considerably in recent years. A few publications have printed data showing some of the physical and chemical prupertie3 of asbestos, but in many cases this information is difficult to find and is seldom available when needed. During the past ten years, Johns-Manville have received many inquiries on the physical and chemical properties of asbestos fibres. Fortunately, we had some of the information in our files, and we willingly supplied the data. To help relieve this need, we have tried to present briefly in this paper some of the interesting and out-standing properties of asbestos. This information was obtained over a period of years by search of the literature and by experimental investigations. PROPERTIES OF ASBESTOS FIBRES Table I (1, 2) presents, in convenient form for easy comparison, data on the principal properties of the several varieties of commercial 'asbestos' -actinolite, amosite, anthophyllite, chrysotile, crocidolite, and tremolite. Under each variety of fibre is a brief statement describing the properties in terms of structure, mineral association, origin, etc. Some of the more important data in Table I are expanded and presented in Table II (3). SOLUBILITY OF ASBESTOS A report ( 4, 5) discussing the effects of acids and caustic on asbestos fibres was published in Germany in 1927.

Jan 1, 1951

By E. Wolmarans

The selection of the main mineralised zone (MMZ) concentrator milling circuit has followed a comprehensive route over the preceding 10 years. Many knowledgeable parties have contributed and assisted in developing the milling circuit according to the best available information. The final selection of the flow sheet was completed after DRA conducted a techno-economic study on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous (AG) milling. The results from all the above mentioned work indicated that it is possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding circuit. The flow sheet was designed to treat the main mineralised zone (MMZ) arising?s from both underground and open cast operations and incorporates a fully autogenous grinding (AG) circuit. Commissioning of the 375ktpm concentrator at Nkomati Nickel began in August 2009 with the first ore reporting to the mill on the 15th of September 2009.

Jan 1, 2012

"The link between ore texture and mineral liberation has previously been established at a microscopic scale. To construct ore texture models that can be used in mining applications requires this relationship to be retained at a significantly larger scale. This is initially dealt with by finding a basic set of microtextures that form the elements of the ore textures at the next larger mesoscopic scale, simulating these mesotextures at a fine scale, then changing the support of the mesotexture simulations to generate the expected mining block/stope mesotexture distributions. Thus, a mutually exclusive and exhaustive set of spatially locatable mesotextures can be used to fully characterize the metallurgical properties of in situ material.A method that generates expected distributions of mesotextures for any mining block size or shape is proposed, and includes: (1) characterizing the spatial correlation of the set of mesotextures with a single covariance function; (2) generating multiple simulations of mesotextures at a fine scale; and (3) using the simulations at a fine scale to generate the expected mining block/stope mesotexture distributions. A case study, using the George Fisher sediment-hosted base metal deposit in Queensland Queensland, Australia, is developed to demonstrate the proposed methodology as well as show the inadequacy of off-the-shelf approaches.Mining-scale texture models can be used to improve the in situ discrimination of ore from waste by exploiting the joint spatial variability of grades and textures to quantify the expected metal recovery of in situ material, then calculate local marginal cut-off grades. An artificial case study is presented to demonstrate the changes in ore/waste selection when considering ore texture models compared to constant metal recoveries."

Jan 1, 2005

By L. H. McKay

Tailing Dams Three types of dam have been structed to impound tailings from the Allenby mill: 1.- By classifier unit 2.- By earth dam 3.- By direct deposition of tailings The first type, which includes two dams, was built across a shallow valley which sloped down to Similkameen river, just below the mill site. Two earth embankments, one below the other, were built across the valley. Tailings were then piped to Akins classifiers mounted on wooden wheels. The classifiers were set up at one side of the valley and gradually moved ahead on the sand embankment created by the sand discharge from these classifiers, the slime overflow going to settli.ng ponds formed by the dams. Decanting wells were built in the settling ponds by placing four six-by-six timbers vertically in the ground, two feet apart, to which two-by-six tongue-and-groove boards were nailed. The elevations of the ponds were raised, as required, by nailing additional two-by-six boards on the well and bolting on more six-by-six timbers when required. The bottoms of the wells were attached to a covered launder made of three-inch lumber laid on a one per cent grade. This launder carried the overflow through the dam. The second type of dam was built across a long, narrow valley, known as Hitchen's Flat, the upper ~n d of which was about 2½ miles north of the mill. This valley, an ideal tailings site, was 4,000 feet long and from 600 to 800 feet wide. An earth embankment with a concrete spillway through the top was built approximately 28 feet high across the lower end of this valley. Tailings were then dumped into the upper end of valley, with no further expense until the basin was filled up to the level of the flume where this entered the valley. When the upper end of the valley was filled to this point there was still room for more tailings at the lower end. Therefore, a pump was installed to elevate the tailings to build a wall around the upper end of the valley by depositing sands from a launder built up on 20 foot supports and sloping both ways from the pumping station around the upper end of the basin.

Jan 1, 1950

By M. F. Goudge

ROCK wool, one of the most recent additions to the list of Canadian-made, insulating materials, is a soft, light, fibrous material consisting of interlaced, flexible, glassy fibres so exceedingly fine that, individually, they are almost invisible to the naked eye and will float in air. In the process of manufacture, a suitable rock, generally a self-fluxing argillaceous dolomite consisting of nearly equal proportions of acidic and basic constituents, is melted to a completely fluid state and then converted into fibres either by a blast of steam or air, or by a mechanical device. The increase within the past five years in the number of plants in the United States making rock wool and slag wool has been remarkable, especially in view of the depressed conditions prevailing 'with most industries during this period. In 1930, there were only 8 plants reporting production of .these materials, whereas at the present time there are 44 plants in the United States listed as making these products, and there are 3 plants in Canada. In 1929, the total sales of rock-wool products in the United States amounted to-$2,377,324. In 1934, according to the National Rock and Slag Wool Association, 26 member companies reported sales of $3,695,405, and in 1935 the sale's of 30 member companies had a value of $5,571,469. The establishment of the rock-wool industry in Canada followed the publication in 1931 of a report (1) by the Mines Branch, Department of Mines, Ottawa, in which was set forth the results of field work and laboratory studies which indicated that large deposits of rock in the Niagara peninsula, hitherto regarded as valueless, were suitable for the making of rock wool. This report was supplemented in 1934 by another report (2), giving the results of further laboratory and commercial-scale tests on the rock from these particular deposits, which proved conclusively that rock wool of good quality could be made from the rock in question.

Jan 1, 1936

By E. M. Stiles

Introduction The papers that follow deal with recently completed major improvements in practices at the Sullivan operations in Kimberley. The papers have been prepared by members of the Consolidated Engineering Staff and outline the construction programme which has been in progress for the past three years, entailing an expenditure of some millions of dollars. Four major operational changes have been brought about in the mine and concentrator. They are: (1) A change in backfill procedure for filling stopes below the 3900 level. (2) A 12,000-ton,per-day sink-float plant at the concentrator. (3) A new haulage system from the mine to the concentrator. (4) A completely new crushing plant and ore storage facilities located underground. A brief outline of the background and history leading up to this overall project will be given to show how each started as an independent betterment and how they were finally co-ordinated into one major programme. The first of these, namely, the necessity for backfilling stopes below the 3900 level, was the most pressing problem. All filling to date bad been done above the 3900 level, where mining was carried on in an irregular pattern of open stoping. Stopes below the 3900 level were first opened in 1940 and are being worked on a regular pattern of panel sub-level open diamond drill stopes. The two areas are separated by a sill pillar traversing the entire length of the vein at the 3900 level elevation.

Jan 1, 1950

By Casey Erickson

Goldstrike Property ??Located in Elko, NV USA?Carlin Trend ??Mining Since 1985 ??27 Million Ounces of Gold Mined ??Production of 400,000 tons/day ??1,600 Employees

May 1, 2011

By Robert B. Parsons

"Exploration and development of mineral resources in developing countries by Canadian-based multinational mining companies is becoming increasingly common. One problem being encountered is that the objectives of the governments of developing countries can differ from those of developed countries. These objectives are not always consistent with maximizing returns from the projects, which can create conflicts between the mining company's responsibility to its shareholders and the desire to be a good corporate citizen. This article discusses how a mining tax regime can be designed to make the social goals of a government consistent with the economic goals of the company.IntroductionAt the recent International Seminar on Mining Taxation organized by CIM and the United Nations there was considerable discussion about the role of international mining companies operating in developing countries. Not surprisingly, given the diversity of backgrounds of individuals attending the Seminar, there were different opinions about what this role should be.Government PositionRepresentatives of governments pointed out the strong desires of their countries for technology, high-level technical training of their workforce, increased employment, and development of social infrastructure. They pointed out that, to a large extent, these objectives could be more efficiently met by mining companies operating in the country than by the governments themselves. For example, a multinational mining company (""MMC"") would have extensive knowledge of the various technologies available, and would have performed a detailed evaluation of the mineral resources before choosing the most cost-efficient technology for that project. They would, therefore be in an ideal position to assist the country in importing and developing such technology. Similarly, the company could provide opportunities for hands-on training, both at the technical and managerial levels, which would otherwise be unavailable to the government."

Jan 1, 1991

By W. P. Campbell

Introduction OWING to the necessity of curtailing the length of this paper, nothing like an exhaustive treatment of the subject will be attempted. Instead, merely a few aspects will be considered, viz., water trouble in wells, sampling of waters, analysis, methods of reporting analysis, and the comparison of a few typical waters. The waters discussed will not be confined to those occurring in areas where oil or gas has already been found, but will include samples from areas in which drilling is being carried on in the hope that oil or gas may be found, i.e., from unproved fields. The Water Problem The problem of dealing with water encountered in oil and gas producing areas has engaged the attention of petroleum engineers from the early days of the industry. Water was not always considered a menace to oil sands; indeed, a certain amount of it was considered beneficial in some areas, but if such exist today they are very exceptional. In some fields, the problem is more acute than in others, and at times has baffled all attempts to solve it satisfactorily. Wells have been brought-in with promise of good production, but after a brief period have 'gone to water'. Whether ?it has always been a case of poor engineering in the form of unsuccessful water shut-off of 'top' or 'bottom' water, or because 'edge' water was present and water and oil were in such close contact it was impossible to remove the one without the other, is hard to say.

Jan 1, 1929

By K. Buxmann

Climate change is a subject of growing concern. Based on the International Energy Agency, about 19% of man made greenhouse gas emissions globally are generated by the transport sector. This paper will focus on the environmental aspects of the light-weighting in transport and the resulting savings of fuel and electricity. Aluminium is an option for lightweight applications in transport, with very high benefits not only in the use stage, but also in the stage of vehicle recycling. Life cycle assessment is used to quantify the relative benefits of light-weighting specific components of cars, commercial road vehicles, buses, ships and trains. A vehicle consists of many components, which are produced by different processes and undergo different types of end-of-life operations. This document does not intend to compare a generic aluminium vehicle with a generic "heavy materials" vehicle. It rather tries to use a pragmatic approach based on specific examples of components where aluminium is used and can be used in the design of new vehicles, also taking into account future developments. The case studies in this paper are based on real cases where aluminium was used. For each component, sensitivity analyses are applied to see the impact of specific parameters such as the end-of-life recycling rate and the use stage driving distance. Significant greenhouse gas savings by the use of aluminium are demonstrated for cars and even higher ones for trucks, buses, trains and ships. In addition, the total potential benefits of light-weighting with aluminium are shown on the global level.

Jan 1, 2007

By M. N. Pons, E. Benizri, B. Laubie, A. Bani, Université de Lorraine LRGP, P. Kidd, A. J. M. Baker

"Serpentine (i.e. ultramafic) outcrops in Europe cover more than 10,000 km2 and have a low-fertility and low-productivity, making them unattractive for traditional agriculture. In general, these areas are slowly abandoned by local farmers, affected by strong rural exodus and landscapes undergo a process of closure. However, ultramafic landscapes have the potential to provide multiple ecosystem services that can contribute to Europe’s goals towards insuring food security, production of renewable raw materials and renewable energy. Phytomining (agromining) aims at cultivating metal hyperaccumulator plants that are able to accumulate Ni and other strategic elements from metal-rich soils and transport them to the shoots (>1%), which can then be harvested as a bio-ore. Such metal-rich biomass can be used to recover highly valuable metals, e.g. nickel (Ni) and also to produce energy (heat, electricity). Nickel agromining can thus offer an eco-efficient alternative to classical pyro- or hydrometallurgical processes without disturbing the soil cover and the geology from soils and rocks that would be considered as low grade ores or sterile material for conventional mining methods.Phytomining agroecosystems can lead to better soil resource efficiency and can offer a fully integrated, new agromining agriculture that could cover thousands of km2 in Europe, benefit local communities with a sustainable rural development and provide a wide array of ecosystem services which will need to be optimised under a life cycle assessment methodology:1. Production of bio-sourced metal products2. Production of energy biomass3. Restoration of soil fertility for conventional agriculture (Ni stress)4. Limiting Ni intake by local populations and farmers5. Use and conservation of local biodiversity (plant and soil fauna and microflora) as cultivated ecosystems6. Store carbon in cultivated soils7. Enhance pollination activity at landscape level.Nickel agromining could therefore change the economical balance in historically-disadvantaged ultramaficregions of Europe"

Jan 1, 2016

By M. Rebolledo, N. Mora, G. Zarate

For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Jetti Resources has developed a novel hydrometallurgical alternative to extract metals of value from mineral ores that the mining industry has struggled to process. Jetti’s catalytic technology, whilst being especially advantaged for extracting copper from low-grade and highly refractory minerals, such as chalcopyrite, seamlessly integrates with existing heap leaching methods and downstream processing operations. The technology uses a catalyst which weakens the metal-sulfide bond in the crystalline structure of the chalcopyrite mineral and alters the structure of the passivation layer allowing the leaching process to continue. Metallurgical test work was conducted to examine the effect of ore variability, in terms of grade and copper deportment. The results presented in this study highlight the amenability of the technology and demonstrate that it is possible to enhance leaching performance of copper primary sulfides over a wide range of copper grades, from 0.1 to 2.2%. Further, it is concluded that despite the copper grade, the tests with increasing chalcopyrite content render copper recoveries up to 4 times higher compared to the tests under non-catalyzed conditions. Jetti’s catalytic technology is currently being evaluated at larger scales, namely a commercial dump leach operation and 50-tonne crib tests. The results obtained thus far are compared to the results from conventional sulfide heap leaching tests. INTRODUCTION For decades, the mining industry has been focussed to find an efficient and economically attractive process for the leaching of chalcopyrite. Chalcopyrite (CuFeS2) is the most abundant and recalcitrant of the copper sulfides (Singer, 2017). Owing to its abundance and economic importance, it is the most demandable natural source for copper worldwide. In fact, the projected demand for copper is further expected to rise much higher beyond the current demand by the year 2020 (Panda et al., 2015). Therefore, it becomes imperative to find low intensity hydrometallurgical technologies for the extraction of copper from chalcopyrite in ores of such low-grades that are un-economic to concentrate and to augment the supply by extracting copper from ores with complex mineralogy that cannot be concentrated (Watling, 2013).

Jan 1, 2019