Search Documents

By T. S. Smith

INTRODUCTION IN PREPARING this paper for the District 4 Meeting, three factors had to be considered. First, the paper must fit the time alloted; second, it must give a general picture of the geology for those unfamiliar with the property; and third, it must contain some new material in order to be of interest to local delegates. The most comprehensive extant discussion of the geology of the property of McKenzie Red Lake Gold Mines, Limited, is contained in Horwood's report on the general Red Lake area ( 1). This report is the 'bible' of the area, and a general paper on the geology of this particular mine would almost certainly appear to be a condensation of it. It was thought, therefore, that the most suitable procedure would be to base the general outline on Horwood' s report, to extend that outline where possible from information gained since its publication, and finally to leave dangling for the contemplative geologist some of the ideas and problems which ?are currently under consideration. LOCATION AND HISTORY The property of McKenzie Red Lake Gold Mines, Limited, is in Dome township, in the Red Lake mining division of northwestern Ontario. The mine is on McKenzie Island, about four miles north, by water, of the Hasaga mine and old Howey mine.

Jan 1, 1951

By Chuck Edwards

Whatever your opinion of the validity of the scientific case for global warming, or of the wisdom of the Kyoto Protocol, it would seem judicious to err on the side of caution and try to sensibly minimize global climate change. To this end, we should take prudent steps to minimize our emission of greenhouse gases. Cameco is the world's leading supplier of uranium for use as fuel in nuclear power plants. Cameco’s uranium production fuels nuclear power plants in 16 countries. Nuclear power plants generate clean electricity without greenhouse gas emissions. This presentation describes the role that uranium and nuclear power can have in meeting the growing demand for electricity and at the same time combating global climate change.

Jan 1, 2004

By C. J. Van Treeck

PGE concentrations of 18 g/t occur in the pyroxene rich rocks at the Union Bay Alaskantype complex. This PGE enrichment is hosted in magnetite veins. These veins cross magmatic layering and have an irregular morphology in both outcrop and thin section. Fe-Ti oxide geothermometry suggests that this mineralization took place between ~700-400°C. A variation in the amount of ilmenite and Mg- Al spinel exsolution in magnetite correlates with temperature estimates, lower temperature magnetite has less exsolution. Hydrous silicates form an alteration envelope around magnetite veins with a formation temperature of <575oC, vary with temperature, and contain appreciable amounts of Cl. Interaction of a PGE-Fe-Cl rich fluid with clinopyroxene increased the fluids pH and decreased PGE and Fe solubility depositing a PGE enriched magnetite within the Pyroxenites and Olivine Pyroxenites of the Union Bay complex.

May 1, 2003

By C S. Walker

This paper analyzes the physical, operational and economic site conditions which were conducive to the design of a diesel-electric power plant wherein the over-all use of the thermal energy of the fuel exceeds 80 per cent. The heat energy supplied to the diesel engines is recovered in power generation, vapour phase cooling, waste heat boilers, air to exhaust gas heat exchangers and lubricating oil coolers. Electric boilers are also integrated into the plant design to enable the ratio of electric power output to heat recovery to be varied to suit the seasonal and daily variations. The criteria relative to thermal and electric power design requirements are discussed, and the design details of some parts of the plant which conform to these criteria are illustrated. Some data in regard to the actual operation of the plant over a short period are also included. Introduction THE Cantung mine (Canada Tungsten Mining Corporation) is located some 180 miles north-east of Watson Lake, Yukon Territory. It is situated on the upper reaches of the Flat river at an elevation of about 3,700 feet.

Jan 1, 1965

By John G. Payne

The Pebble deposit contains three contiguous zones. In the Pebble West zone, granodiorite stocks intrude gently warped volcanosedimentary rocks that had been intruded by diorite sills and two felsic intrusion breccias. In the Central zone, volcanosedimentary rocks are cut by diorite and granodiorite sills; the latter are genetically associated with the granodiorite stocks. In these zones, widespread potassic alteration consists of brown biotite and K-feldspar, with abundant quartz-carbonate-sulphide vein stockworks. Chalcopyrite/pyrite ratios range from 2/1 to 1/20. Diorite hosts the highest-grade mineralization, with much of it being disseminated. Patchy, later phyllic alteration is moderate and commonly depleted in copper. The Pebble East zone occupies a granodiorite stock and intruded host rocks below an eastwardly thickening wedge of barren Tertiary volcanic and sedimentary rocks up to 600 m thick. Brown biotite alteration and copper mineralization are strong, with chalcopyrite/pyrite ratios commonly over 1/1. The zone extends to a depth of at least 1200 m below surface; some drill holes bottomed in strong mineralization. Later, weak to moderate sericitic alteration removed some chalcopyrite and locally remobilized gold. The Pebble deposit has a Measured/Indicated resource of 3 billion tonnes grading 0.28% Cu, 0.32 g/t Au and 0.015% Mo (= 0.5% copper-equivalent) and an Inferred resource of 1.13 billion tonnes grading 0.30 g/t Au, 0.27% Cu and 0.015% Mo (0.55% copper-equivalent). The Pebble East zone has an Inferred resource of 2.13 billion tonnes grading 0.55% Cu, 0.34 g/t Au, and 0.037% Mo (0.97% copper-equivalent). The Pebble East zone is open to the east and to a lesser extent to the north, south, and to depth.

May 1, 2006

By M. A. Cristovici

"In the last few years CANMET has taken the initiative by investigating the possibility of reactivating abandoned old tailings dumps (for gold production) which would be of potential economic interest across Canada.Nova Scotia was one location where numerous gold processing plants were in operation in the early days. A survey of the old tailing dumps was conducted and some areas of interest were selected. Among them were the sites identified as Lake Charlotte and Forest Hill.Ore samples collected from those tailing ponds were examined for their chemico-mineralogical composition and investigated for gold extraction. Three technological concepts were tested: flotation, direct cyanidation and flotation followed by cyanidation of the flotation concentrate. The combined flotation- cyanidation variant, yielding a gold recovery in the range of 90%, was recommended for processing the tailing ore.Pilot-plant runs carried out by a commercial testing firm (data not included in this paper) confirmed the conditions and results of CANMET&apos;s technology.As a result a consulting-engineering firm designed the processing plant which is expected to begin operation in the near future.IntroductionIn the last few years CANMET initiated a research program to locate in Canada, abandoned gold-silver tailing dumps of potential economic interest and to explore the possibility of recovering the precious metals from these old deposits by modern techniques.A literature search revealed that the first production of gold in Canada was recorded in British Columbia in 1858 and that, production prior to 1900 was essentially restricted to the Yukon, British Columbia Nova Scotia and Quebec. During the early 1900s, Ontario, Manitoba and the North West Territories joined the ranks of the gold producers.Early milling and recovery methods were mainly restricted to sluice boxes, gravity stamps and amalgamation. Froth flotation and cyanidation were introduced at about the turn of the century.Recovery of gold at plants using flotation and cyanidation was very good, therefore the tailing ponds resulting from those operations would, very likely be of little or no economic importance. However, the gold recovery at the amalgamation and gravity concentration plants appeared to be lower, indicating the possibility that significant amounts of recoverable gold would have been carried with the tailings to the dump sites."

Jan 1, 1986

By J. -F. Blais, M. -O. Simonnot, J. Mocellin, G. Mercier, J. -L. Morel

Large quantities of ferromanganese sludge are generated as waste material by blast furnace during the manufacturing of ferromanganese. These slags are very rich in manganese, zinc and lead (5 to 40 %). These residues have been deposited in a pond in periphery of the steel industry. Considering the market value of the metals, these brownfield sites can now be considered as secondary resources. We have developed a hydrometallurgical process for selectively leaching Zn, Mn and Pb in order to produce compounds of Mn and Zn pure enough to be economically recoverable and a residue rich in Pb. Batch laboratory experiments were carried out to determine appropriate leaching conditions to maximize zinc extraction (100 %) and manganese extraction (90.0 %) with sulfuric acid and to generate a residue containing 15 to 30% of lead. This Pb residue is recyclable by another process.

Jan 1, 2015

By J. Asfahani

"The Schlumberger configuration used in geoelectrical sounding is slightly adapted here to obtain reliable data for both shallow and deep penetration depths from the same survey. In this configuration, two kinds of current electrode half-spacings are used: the first enables construction of vertical electrical resistivity sounding (VES) curves for shallow depths (<50 m), and the second for depths =250 m. For a given VES location, two field curves are measured and interpreted using two standard approaches. Practical characteristics of such a modified configuration are illustrated with two field applications in Syria. The first aims to characterize the structure of Quaternary and recent deposits in the Al-Ghab depression region, and the second deals with exploration for phosphatic sedimentary units in the Al-Sharquieh mine. La configuration de Schlumberger normalement employée dans les levés géoélectriques a été légèrement modifiée afin d’obtenir des données fiables à faible et forte profondeur durant le même levé. Dans cette nouvelle configuration, deux types de demi-espacements des électrodes sont utilisés : le premier permet le développement de courbes de sondage de résistivité électrique verticales (REV) pour les faibles profondeurs (<50 m), et le second atteint des profondeurs =250 m. Pour une localité REV donnée, deux courbes de champs sont donc mesurées et interprétées grâce à deux approches standardisées. Les caractéristiques pratiques de cette configuration modifiée sont illustrées par deus exemples d’application en Syrie. Le premier vise la caractérisation de la structure des dépôts Quaternaires et récents de la région de la dépression d’Al-Ghab, et le second traite de l’exploration pour des unités phosphatiques sédimentaires à la mine Al-Sharquieh."

Jan 1, 2009

By J. P. Bennett, W. E. Lee, S. Zhnag, K. S. Kwong

An EAF slag properly saturated in MgO results in increased refractory service life and steelmaking efficiency. A computer model was developed using phase equilibrium data from the MgO-CaO-SiO2-FeO, MgO-CaO-Al2O3-SiO2 and SiO2-CaO-Al2O3-FeO systems to predict MgO saturated slag chemistry. This model has been successfully applied to a commercial EAF, although disciplined plant practices are required to achieve benefits from slag chemistry control.

Jan 1, 2004

Risk management has taken on renewed vigor since the economic crisis of the late 2000s. The resources of governments, individuals, and corporations are being stretched to a point where only the most promising projects move forward. Risk management is a crucial part of the decision making process, yet it remains a broad term that includes disciplines from engineering to finance. A collaborative effort will be necessary to ensure that the most auspicious and appropriate projects are the ones moving forward. Risk management can be quantified to an extent by comparing the likelihood of an instance with the result of consequence of the instance occurring. In this manner it is possible to assign risk factors to instances and ultimately, begin to associate monetary value to the instance. Carbon sequestration is an emerging field that has a number of unique challenges. Risk management and mitigation must be an integral part of the overall picture. This begins with the planning and design phase, continues through implementation and production, site closure, and does not cease until termination of liability. The ability of carbon sequestration projects to successfully assess, mitigate, and recover from leaks will be a decisive characteristic of overall success. The costs of mitigation and failure will need to be analyzed on a test level, but will still need to be reliable enough to extrapolate to a commercial level operation. This paper will build a risk management profile based on case studies and field tests in Tennessee and Virginia. These tests are scheduled to commence in late 2013 and consist of small-scale injection tests in unconventional storage reservoirs with an emphasis on enhanced coalbed methane (ECBM) recovery and enhanced gas recovery. The ultimate goal will be to provide a clear and concise direction to move carbon sequestration from the test phase to commercial scale. While it is necessary from a risk management perspective to analyze all risk points, the scope of this paper will focus on pre-injection risk assessment for carbon dioxide (CO2) leakage potential. Despite the differences between the two tests, CBM compared to shale among other differences, a framework for analysis and mitigation can be developed pertaining to leakage risk. The probability of each type of failure will be assessed and analyzed, and plans to mitigate or reduce these risks will be reviewed.

Aug 1, 2013

By A. Berry, N. R. Banerjee, C. S. Finnigan, M. Fayek, N. J. Bridge

Lac Cinquante is a mineralogically simple, vein-hosted uranium deposit in Archean basement rocks (Angikuni greenstone belt) that originally were unconformably overlain by Proterozoic sedimentary and volcanic rocks of the Baker Lake Group (BLG). Basement rocks are mainly pillowed and massive tholeiitic lavas (N-MORB) with interbedded tuff; overlying sedimentary rocks comprise a basal talus/fault breccia that grades upward into fluvial sedimentary rocks and subaerial, trachytic volcanic rocks; granite and porphyry dikes (Hudson and/or Nueltin granitoids) intrude the basement rocks. A typical section through the Main Zone comprises 1) laminated ‘tuff’, 2) altered (carbonate-hematite-chlorite) schistose ‘tuff’, 3) a pitchblende-bearing, breccia-vein, 4) altered ‘tuff’, and 5) laminated ‘tuff’. The vein comprises brecciated chlorite, hematite, and pitchblende with carbonate cementing the breccia. Graphitic ‘tuff’ with sulfide-stringer veinlets locally overlies or underlies the vein. Pitchblende also occurs in the altered rocks and in gash veins that cut basement rocks. U-Pb ages on pitchblende fall into two groups: one at 1828 } 29 Ma reflects primary uranium mineralization, and a second at 1437 } 31 Ma represents resetting. Pb-Pb chemical ages show other resetting events at 1260-1321Ma, 895 Ma, 741-813 Ma, and 660-706 Ma. One possible genetic model for the Lac Cinquante deposit involves leaching of uranium from granitoids and the BLG by basinal brines that migrated to depositional sites where graphitic rocks acted as a reductant. A second model requires that uranium was sole-sourced from the BLG and that granitoid rocks provided heat to drive the hydrothermal system, which leached and ultimately precipitated uranium. The deposit has characteristics similar to vein-type uranium deposits in the Beaverlodge District of Saskatchewan

Jan 1, 2013

By Y. Özçelik

Rocks show a variety of engineering and physical properties that affect typical quarry operation such as diamond wire cutting in the marble quarry. The physical and mechanical properties of rocks depend on their mineralogical and petrographical characteristics. The purpose of this study is to investigate the effects of mineralogical and petrographical properties of a rock, such as grain size and mineral content, and how these affect the wearing of diamond bead and cutting rate in a diamond wire cutting operation in a marble quarry. Statistical analysis is used to carry out the study. Three different rock types were examined, namely, hard rock (andesite) and softer rocks like limestone and marble. The study revealed that the mineralogical and petrographical properties of the rocks, such as percentage of quartz, biotite, plagioclase, matrix minerals, and opaque minerals, are important. In addition, the grain size of quartz and plagioclase in andesitic rocks and calcite grain size for carbonate rocks significantly influenced the wear rate and cutting rate in diamond wire cutting operations.

Jan 1, 2005

By P. Marcotte, G. LeBlanc, S. Ouellette, J. Boutin

"To characterize noise and vibration sources of different types of mining equipment used in underground mining, the authors performed a study in eight Quebec mines on 28 pieces of equipment. This paper presents the procedure followed to select the equipment to be evaluated, and the low-cost acquisition system developed to perform multichannel time-domain data acquisition in harsh environments. It also presents the results obtained for the noise level produced by the equipment and for handarm and whole-body vibration exposures.RÉSUMÉ Dans le but de caractériser les sources de bruits et de vibrations de divers équipements miniers utilisés sous terre, les auteurs ont étudié 28 équipements dans huit mines du Québec. L’article présente la procédure suivie pour choisir les équipements à évaluer ainsi qu’un système multicanal à faible coût développé pour acquérir des données dans des environnements difficiles. Il présente aussi les résultats obtenus pour les niveaux de bruit produit par les équipements et pour les expositions main-bras et du corps entier aux vibrations."

Jan 1, 2015

By D. E. Keeley

Introduction Gunite is a mixture of sand and cement applied to any surface by being shot by compressed air through a nozzle, where it is wetted just before leaving the orifice. The mixture is transported through a hose from a machine called a &apos;cement-gun&apos;(l). Guniting of rock surfaces has been standard practice at the Mcintyre Porcupine Mines, Limited, for several years. Where used on walls and backs of cross-cuts; shaft stations, and other rock openings, as an air seal, gunite has eliminated the necessity of constant scaling to keep rock from falling from these places, and, under worse conditions, it has been used in place of timber supports. This has been of definite help in reducing costs, promoting safety, and minimizing fire hazards. During the past year guniting has been quite extensively used here in the rock head-works of the new internal shaft, No. 12, sunk from the 3,875-foot level. Gunite is at present being applied to the stations of that shaft well below a mile from the surface. This paper describes the method of guniting as carried out at the McIntyre, and illustrates how, by the adoption of this process, mining problems connected with scaling and loose ground have been completely solved. It is hoped that the information presented may stimulate discussion and assist in the use of gunite in this and other mines. The guniting method of applying cement was first developed by Carl E. Akeley (2), Curator of the Field Museum, Chicago, in 1907, and was exhibited in New York at the Cement Show in 1910. The museum was located in one of the old World&apos;s Fair buildings, built of roughcast and in bad repair. Mr. Akeley, who was a man of inventive nature, set about devising means of applying cement to repair the walls. The cement-gun was the result. Mr. Akeley was a taxidermist of note, a sculptor, and also the inventor of the Akeley camera. In his work, he was in the habit of using fast setting materials to build up foundations for statues, etc.

Jan 1, 1934

By Donald O. Downing

"IntroductionThis paper provides an overview of the coal mining industry in Canada with a description of current circumstances. The Canadian industry is placed in a global context and the future prospects of the industry are described. The export market is very important to the future of Canadian coal production and the essential aspects of the market are explained. Future prospects are very much tied to metallurgical coal exports and some key characteristics of that market are discussed, including major technological changes in the industry. Stability in 1996The Canadian coal industry enjoyed another strong year in 1996 continuing a trend established over the last four years. The strength of the industry is based on a stable domestic industry and a relatively healthy inter- national market. The figures bear out these statements. In 1996 total production reached 75 million tonnes and consumption was 52 million tonnes. The major markets for coal in Canada are electricity generating stations (Alberta, Saskatchewan, Manitoba, Ontario, New Brunswick, Nova Scotia) and the steel industry in southern Ontario. Approximately 11 million tonnes of coal were imported and exports reached a new record of 34.5 million tonnes, mainly from western Canada. Canadian Coal FlowsCanada represents a unique case in the coal world because we both import and export coal (Fig. 1). The reason for this apparent dichotomy is Canada’s geography. Eastern Canadian coal markets are located closer to the eastern United States coal fields and are basically served by them. This is true for both thermal and metallurgical coal. Major imported coal users are the steel industry, electricity generators and other industry including the cement industry in southern Ontario, Quebec, New Brunswick, with a little coal imported into Manitoba. Only about 2.2 million tonnes of western Canadian coal move into the east, including both lignite and bituminous coal."

Jan 1, 1997

By E. E. Mason

THE Myrtle group of mining claims is situated on Barkerville mountain in the Cariboo mining district of British Columbia, west of the old mining town of Barkerville. An 1,800-foot adit, known as the Shamrock tunnel, was driven in 1935-36 from the Barkerville road and in the general direction of the Myrtle group. It was proposed to enlarge this adit to more convenient section, extend it 2,500 feet int0 Myrtle ground, and from there drive a main entry 3,000 feet along the length of the group. Several laterals were also to be driven off this main entry as part of the tunnel schedule. It was thus originally proposed to drive 5,500 feet of new adit and 1,800 feet of laterals, a total of 7,300 feet of new work. Work was commenced with a bulldozer on April 21st, 1941, cutting a bench on the hillside for a plant site. The power plant was ready for operation on August 8th. Slashing and re-timbering of the old adit rook longer than was expected. It was found that 57 per cent of the length required timbering, chiefly by fore-poling, and there was also trouble in several sections with swelling ground. First round in the new face was taken on September 17th, when a 2-shift daily schedule was commenced. Due to delays in delivery of electrical equipment, it was not possible to add the third shift until November 14th. From then on, a 3-shift daily schedule was maintained with the exception of holidays and fortnightly change Sundays until August 1st, 1942, when shortage of labour caused the dropping of a shift. All work was suspended on August 14th. The ground through which the tunnel passed was such that the driving was often interrupted by the need of protective timber at the face. Further, crews were continuously employed timbering behind the face, and in maintenance of timbered sections in swelling ground. Roughly 980 feet of the new workings are now timbered, about 21 per cent of the total.

Jan 1, 1942

By Harry Siewert, Tom Milner, Jack Stickney

"LocationThe Gibraltar mine is located in central British Columbia (NTS 93B/9W), 362 km north of Vancouver. Access is provided by 20 km of paved road from McLeese Lake, which lies 45 km north of Williams Lake on Highway 97. Latitude and longitude of the mine are 52° 30' and 122° 16', respectively.The total area of the McLeese Lake site is approximately 1700 ha (4200 acres). This includes the orebodies, dumps, surface drainage collection system, plant site, roads and tailings ponds.Brief Description of OperationOre is mined by open pit methods and is concentrated using conventional crushing, grinding and flotation processes. Copper and molybdenum flotation occurs at an average rate of 40 000 tons per day. Tailing is discharged to an impoundment area and the water recycled as process water. Additional copper is extracted from the waste dumps using sulphuric acid as a leach solution followed by solvent extraction and electrowinning.HistoryExploration by Gibraltar began in 1964, continuing until late 1970, at which time it was announced that the property would go into production. Construction started in early 1971, with initial production in March 1972. Target capacity of 30 000 tons per day was achieved by the end of March and is currently at 40 000 tons per day.Ore reserves as of January 1, 1998 were 184 384 000 tons grading 0.31% Cu and 0.010% MoS2."

Jan 1, 2000

By Xiaozhu Chen, Qi Ping, Pu Yuan, Qinyong Ma

"In order to investigate the fractal feature of coalmine deep rock fragments under impact loads, variable cross-section split Hopkinson pressure bar apparatus, 50 mm in diameter, was adopted to conduct impact compressive test for rock specimens from -962m deep coalmine. Various impact pressures, such as 0.3, 0.6, 0.9 and 1.2MPa, were selected to implement different loading rates. Sieving statistical analyses were conducted for rock fragments after being impacted, and the particle size distribution of broken rock in various loading rates were calculated with the fractal method and then the corresponding fractal dimension was obtained. Test results shows that there is a good self-similarity and fractal feature in fragments distribution of deep coalmine sandstone under impact loads. The fractal dimension of fragments is between 1.9 and 2.7. The research also indicates that there is an approximate power relationship between dynamic compressive strength and fractal dimension, and a strength power relationship between fractal dimension and average strain rate. Moreover, there is a linear relationship between fractal dimension and specimen absorbed energy. The rock fractured process can be quantitatively described through fractal dimension, which can reflect the deep rock broken degree and is an ideal index to evaluate the distribution of rock fragments.INTRODUCTIONBroken rock is one of the most basic processes in mining operations, rock fragmentation has always been an important index to evaluate rock breaking effect (Xu & Yu, 1984). Macroscopic fragmentation of rock material is the final results of continuous development, expansion, gathering and cutthrough of internal micro-cracks. This process, developing from microscopic damage to macroscopic fragmentation, is an energy dissipation process and shows fractal characteristics (Xie, 1993). Turcotte (1986) has conducted statistical analyses of fragmentation for different kinds of geological materials under various broken conditions, and arrived at the conclusion that fragmentation distribution is a fractal."

Jan 1, 2015

By A. M. Richmond

Introduction The apparent commonplace, and prosaic, nature of building-stones, lime, cement, gypsum, and clay products, and many other miscellaneous non-metallic minerals, such as abrasives, barite, diatomite, magnesite, mica, slate, salts, etc., and their everyday appearance and necessary in our lives, has removed much of the glamour, romance, and speculative attractiveness so frequently associated with our gold, silver, lead, zinc, and copper mining ventures. However, it will be readily appreciated, with but a brief study of the thirty-five or more non-metallic minerals and products which are mined, prepared, or are known to occur, in British Columbia, that the &apos;industrial minerals&apos; industry in the Province has an abundance of interesting technical problems, is fraught with speculative possibilities, and, as such, fully deserves much more technical attention than it has hitherro received. The brief notes presented in this paper show, in summary form, the magnitude of the British Columbia industrial and non-metallic mineral industry; outline in synoptically form the principal deposits of non-metallic minerals presently known; and indicate in a general way a few of the possibilities which exist in the Province for the expansion of the industry. For convenience in presentation, the assembled material has been divided into four sections: 1.-Sraristical information 2.-Strucrural non-metallic minerals 3.-Miscellaneous non-metallic minerals 4.-Non-Metallic mineral possibilities in British Columbia 1. -Statistical Information The writer does not propose to dwell at length on the statistical comparisons and deductions which may be drawn from the four tables which have been compiled for this section of the paper, nor is it considered essential, as the figures present a most emphatic story in themselves.

Jan 1, 1935

By M. Gaumont, F. Robichaud

"Agnico Eagle Mines Limited (AEM) is a Canadian-based gold producer with operations in Canada, Finland and Mexico. In 2010, AEM produced its first gold bar in Nunavut, Canada as it started its Meadowbank operation. It is also in 2010 that AEM acquired the Meliadine property, which is located 25 Km North of Rankin Inlet, Nunavut, Canada. The Meliadine gold project is an advanced exploration and development project, comprising of workers camp, underground and open mines, a processing plant and all the services facilities and infrastructures required to sustain operation in a remote arctic environment.Pending formal board approval, production start-up is planned for Q3 2019 and the process flowsheet is based on an ore processing rate of 1.1 million dry tonnes per year (3,000 dry tonnes per day from underground mining) for the first three years, and 1.98 million dry tonnes per year (5,000 dry tonnes per day from both underground and open pit mining) for the remaining years at 92% process plant availability.To the end of 2015, more than 45 metallurgical test programs have been conducted on the Meliadine deposits. Based on the results of these programs, an optimal gold circuit was designed, comprising of crushing, grinding, gravity separation and cyanide leaching with a carbon-in-leach circuit (CIL), followed by cyanide destruction and filtration of the tails for dry stacking. The assumed gold recovery for the reserves averages 96.0% at a 7.44-g/t gold average mill feed grade."

Jan 1, 2016