Search Documents

By A. Poitras

The Cummings Complex consists of three superposed sills, exhibiting a differentiation pattern: the lowest sill being the most basic and the highest sill, the most acid. Each sill is also characterized by an internal petrographic and geochemical variation which is evidence of differentiation due to fractional crystallization. The REE concentrations in the different units of the complex indicates that the three sills are comagmatic. The interpretation of these results permits the formulation of an emplacement model not previously proposed for this complex.

Jan 1, 1984

By P. J. Routledge

THE purpose of this paper is to discuss the practical aspects of locating gravel deposits and of establishing efficient, portable concrete aggregate beneficiation plants for use on construction projects where limited amounts of high-quality gravel and sand are required. Certain projects are listed, in order to demonstrate the wide variety of problems encountered. Routledge Gravel Contractors Limited, North Vancouver, have supplied concrete aggregate for construction projects in British Colum-bia since 1957. In tl1at year, in sup-plying aggregate for a small project at a site on the northern coast of British Columbia, our quote was as follows: Concrete aggregate to specifications, f.o.b. scow, North Vancouver$ 1.75 per cu. yd. Scowing charges to site. $16.00 per cu. yd. At that time, our company realized that more attractive quotations could be submitted if local gravel was utilized where available. Port-able equipment was then acquired and a simple screening plant (Figures 1 and 1a) was at first used. This was later replaced by heavier, more versatile equipment. The use of suitable equipment, the keeping of cartage to a mini-

Jan 1, 1962

By J. A. Chamberlain

DURING a recent trip across Canada and parts of the northern United States, the. writer examined some forty mine models. Construction -details and the uses to which the models were being put were outlined in a report to Eldorado Mining and Refining, Limited, and a specific model was proposed on the basis of the Company's particular needs at their Beaverlodge operation. It was felt, however, that portions of the report would be of some value to anyone contemplating building a mine model. For this reason, a synopsis of some of the more important aspects of the problem is presented here, together with a suggested model type that appears to have wide application. Thanks are due not only to Eldorado for permission to publish the following material, but also to the many mine personnel across Canada who allowed the writer to examine their models and gave freely of their time in discussion.

Jan 1, 1958

By B. R. Hart, S. S. Dimov, J. Fournier

Carbonaceous matter (c-matter) in sulphide ores can adversely affect the process of gold recovery during cyanidation due to its ability to adsorb, or preg-rob, gold from a cyanide leach solution. This paper describes a standardized procedure for characterization of c-matter in an ore sample providing detailed information on its composition, maturity and preg-robbing capacity. The procedure utilizes the following complementary analytical techniques in conjunction with several chemical tests and assays: SEM/EDX Raman spectroscopy and TOF-SIMS. Results of the test can be used as a predictive tool to estimate the impact the c-matter will have on the gold recovery process. A comparison between predicted preg-robbing behaviour and cyanidation test results are presented.

Jan 1, 2011

By Grant Small, Jessica Kinal, Christopher J. Greet

"The conversion from an electrochemically reactive grinding media (forged steel) to a more electrochemically inert alloy (high chrome white iron) not only reduces the wear rate of the grinding media, but also has an impact on the grinding chemistry. Typically the grinding chemistry becomes more oxidising, with less reducing Eh values and more dissolved oxygen in the pulp. There is also a decrease in the EDTA extractable iron, which is an indication of the change in the media corrosion. These changes are indicative of alterations in the surface chemistry of the minerals that the operator is trying to separate. For porphyry copper ores the changes in the pulp and surface chemistry not only affect the copper sulphide minerals, but also impact the iron sulphides (i.e. pyrite and pyrrhotite). Generally, with more oxidising pulp chemical conditions during grinding there is an increase in the oxidation of the iron sulphides which renders their surfaces hydrophilic, thereby depressing flotation. This leads to improved selectivity for copper sulphides against iron sulphides.INTRODUCTIONPorphyry copper deposits are the dominant source of copper that is mined today to satisfy global demand. These style of deposits typically contain one percent copper mostly as chalcopyrite, but may contain other copper bearing minerals (for example, bornite, chalcocite, azurite, malachite), small quantities of pyrite and quartz. Porphyry copper deposits also contain economically significant quantities of gold, silver and molybdenum. Interestingly, the majority of the world’s porphyry copper deposits are concentrated along tectonic plate boundaries (Figure 1)."

Jan 1, 2016

By D. J. Lloyd

"Bending is involved in the forming of many sheet parts and it is important to understand the phenomena involved. In this paper the basic equations describing bending on a global scale are compared with strain measurements of bent sheet. The development of strain on a local, microstructural scale is also investigated, as is the general aspects of plasticity and the failure process. It is shown that the global equations can be used to estimate the strains involved and the local strains can be attributed to various aspects of the plasticity. The bendability can be related to the fracture strain of the sheet and the ability of a sheet alloy to accommodate the necessary bending to form the part can be assessed.INTRODUCTION The ability of a sheet alloy to undergo bending without failure is an important capability in the forming of many parts and it is useful to be able to assess the bendability of an alloy during its development. The basic mechanics of bending were developed in the 1950s (Lubhan & Sachs, 1950; Hoffman & Sachs, 1953). When a sheet is bent the upper bend surface is in tension, the lower surface in compression and at some point within the sheet there is a plane of zero strain which is referred to as the neutral axis. For sheet exhibiting limited plasticity the neutral axis is static and occurs at the mid-point of the sheet thickness but for sheet exhibiting extensive plasticity the neutral axis progresses deeper in to the sheet as bending progresses. This results in two expressions for the maximum strain at the upper bend surface depending on the motion of the neutral axis. For Al alloys such as AA6111, AA6016 and the like extensive plasticity occurs and the neutral axis is expected to move during bending. However, very few studies have examined how the neutral axis motion and the strains develop, compared with the mechanics analysis. Geist and Parker (1984) used hardness measurements to investigate neutral axis motion but these experiments did not have the resolution necessary to compare the results with experiment but did indicate neutral axis motion. To understand the nature of plasticity and failure during bending it is important to know the extent of neutral axis motion, the scale of strain gradients developed through the sheet and the maximum strains occurring at the bend surface, finally comparing experimental results with the theoretical predictions. The influence of microstructure on the evolution of strain and failure can then be considered in the context of these parameters. Recently, bending in some automotive Al alloys has been reported mainly from the microstructural perspective (Lloyd, 2000, Lloyd et al., 2002, Mattei et al., 2013) and FEM studies have also investigated the development of plasticity under bending, demonstrating the tendency for strain localization (Becker, 1992, Shi et al., 2014)."

Jan 1, 2018

By R. B. Humphrey

Cut-and-fill mining methods at the Thompson Mine have undergone significant changes since production began in 1961. Changes have been introduced in almost all aspects of the mining operation, from the original timbered chutes and air-operated slushers to the present-day bored raises, footwall ore passes and load-haul-dump units. This paper describes the evolution of mechanized cut-and fill mining methods, highlighting the changes in design for stopes and service openings, ground support methods; hydraulic filling and ventilation systems. A mechanized stoping area is described from the initial mining concept through design, development, construction and mining cycles.

Jan 1, 1979

"Geoscan is used for multi-elemental analysis of conveyed bulk materials in the minerals industry with proven performance and demonstrated paybacks of weeks or months in iron ore, manganese, copper, zinc-lead and phosphate industries. Geoscan-M measures continuously through the full bed depth and is unaffected by belt speed, particle size, layering, mineralogy and dust levels. Increments of typically two minutes are accurately measured and provide the plant operators with tonnage weighted results of contained elements. Measurement of the composition in real time enables prompt feedback to the mining operators and also feed forward to the process operators. Crushed ore increments can be diverted based on composition, such as diverting waste for disposal or marginal material to a stockpile for separate processing. Bulk sorting allows material to be placed into relevant stockpiles for subsequent blending to achieve consistency for process feed. Parameters used for decisions may be primary metal content, deleterious component content, other process parameter, or a combination of these. Process parameter may be the elemental ratio between critical components, e.g. Cu:S ratio, basicity, or the content of an “indicator” element (such as Si indicating material hardness). Benefits will be discussed based on case studies in copper and iron ore.IntroductionAs operators of process plants strive to remain competitive as capital and operating costs increase and commodity prices fluctuate, more focus has been directed at incremental performance improvements at incremental cost rather than major expansions to increase output. The philosophy of working smarter allows plants to adopt technologies proven in other industry sectors to minimise risk. This paper discusses one such technology that the minerals sector is adopting and has found to be safe, reliable and accurate with paybacks of weeks in most applications. New applications continue to be found and major benefits realised at various stages in the processing and handling of ores and products."

Jan 1, 2016

By C. Gosselin, G. M. Payenzo, C. Bazin, M. Desnoyers, G. Chevalier

"ArcelorMittal Mines Canada operates hydraulic classifiers to reduce the silica content of an iron oxide concentrate from 4.5% to less than 1.2% SiO2. Sampling campaigns were conducted to develop a preliminary model for the hydraulic classifier. Results show that iron oxide and quartz are respectively concentrated in the coarse and fine size fractions of the classifier feed. The mineral partition curves in the classifier and the size distribution of the minerals in the feed are used to simulate the classifier operation in order to identify the source of variability observed in the daily plant production data. Results indicate that most of the variation is probably caused by unsteady operating conditions of the classifiers.INTRODUCTION Hydraulic classifiers are a class of gravity separation devices (Wills, 1992) used to classify particles according to their size and specific gravity. Hydraulic classifiers also known as density separators (Hearn, 2002) combine hindered settling and upward flow of water to selectively entrain light particles to an overflow stream. Denser particles settle to an underflow stream. Hydraulic classifiers are used for various purposes ranging from cleaning of coal (Das, Sarkar, & Mehrotra, 2009), recovery of chromite from plant tailings (Kumar, Tripathy, & Rao, 2009) to upgrading iron oxide concentrate (Hearn, 2002). ArcelorMittal Mines Canada operates several hydraulic classifiers to upgrade an iron oxide concentrate by removing fine quartz and other light minerals from hematite that is the main iron oxide mineral. A project was initiated to analyze the operation of the classifier in an attempt to identify the source of the variability in the production results and to assess the potential of increasing iron recovery in the classifier. One possible disturbance for the classifier operation is the change in the classifier feed composition and size distribution, while the other considered disturbance is the operation of the classifier. The paper is divided into five sections. The first section summarizes the ore processing sequence for the production of iron oxide pellets to identify the position of the hydraulic classifier in the process. The second section describes the hydraulic classifier. The third section discusses the sampling campaigns conducted on the hydraulic classifier. The method used to process the data from sampling, the results of the data processing and simulation of the classifier are discussed in the remaining sections."

Jan 1, 2012

By Zhuo Chen, Jun Zhou, Jiemin Zhou

Samples of the reacting suspension particles were taken from the reaction shaft of a commercial flash furnace at different heights. The processes of matte and slag formation and morphology of the samples in the shaft were observed and analyzed. Variations of matte and slag composition in the shaft were investigated. By analyzing the samples taken from the settler at different locations, settler processes were studied such as slag formation, agglomeration and separation of matte-slag phases, Fe3O4 reduction, copper-in-slag reduction etc. In accordance with the characteristic of matte and slag formation the flash furnace can be divided into 6 functional regions, and a mechanism model called as “Micro bath process” is proposed for matte and slag formation in a commercial flash furnace. INTRODUCTION During flash smelting, concentrate particles scattered in the reaction shaft complete their oxidation reactions in suspension. The droplets produced fall into the settler beneath with a small amount of un-melted solid particles, agglomerate and separate into matte and slag layers which are tapped out from their tap holes separately. With respect to the extent of slagging reaction in the reaction shaft, there isn’t any commonly accepted understanding in literature (Kimura, Ojima, Mori & Ishii, 1986; Kemori & Kondo et al.,1988; Kemori, Denholm & Kurokawa, 1989; Fagerlund &Jalkanen, 2000). Some assume that the slagging reaction in the shaft can be ignored and some propose that all slag is produced in the shaft. With regards to the characteristics of the physical-chemical changes of concentrate particle in the reaction shaft, although there are some research results reported from pilot scale and commercial scale experiments (Kemori, Ojima & Kondo, 1988; Hagni, Vierrether & Sohn, 1988; Jorgensen, Taylor, Dickinson & Stevenson, 1992; Swinbourne, Simak & Yazawa, 2002; Kivinen & Tuominen, 2005), they are generally limited themselves to theoretical analysis and calculations. No studies are published concerned with the processes of matte and slag generation in the shaft, quantitative analysis of the processes, variations of matte and slag composition and morphologies of the melts along the axis of the shaft, etc.

Jan 1, 2019

By P. Kostuik

"Recent interest in the pipeline transport of solid mate-als has been sparked by the idea that, in an inflationary onomy, pipeline costs are more stable than the costs of any other transport systems. Pipelines have proved over 1e years to be dependable, records indicate that main-•nance and operating costs are comparatively low, and 1eir amenability to automation is of considerable im->rtance.The concept of hydraulic hoisting of solids from under-round, or cross-country hydraulic transportation of con-~ntrates and ores, is currently of prime interest to the ining industry. In general, this paper deals with a preliminary investi-ation of energy losses incurred while transporting a rela-vely heavy, crushed mine product, namely magnetite, oth vertically and horizontally. The basis and validity of everal equations derived by other experimenters to com-ute these losses is discussed. A theoretical analysis of ydraulic hoi:,,ting is made, and, based upon test results, calculation of horsepower requirements for hoisting an re under a given set of conditions is presented. Results indicate that:n vertical transport, the friction head losses are identical to those of clear water, and the total energy requirement for hydraulic hoisting then becomes a function of height of lift, concentration and specific gravity of the solids being hoisted. .-In horizontal transport, friction head losses can be calculated with reasonable accuracy using Bonning-ton's correlation curve. Losses computed utilizing Durand's correlation (K = 85) result in estimates which are too low by 10 to 30 per cent, an<l those calculated using Newitt's correlation (K = 1,100, K = 66) give friction loss values which are too high by 10 to 30 per cent . . -The theoretical horsepower (RMS-hp.) required for hoisting hydraulically is approximately half of that required for conventional double-drum skip hoisting."

Jan 1, 1966

By N. Katsikaros, A. Lewis-Gray, P. Richards

"To optimize gold recovery in complex leach-to-electrowinning processes, Gekko Systems developed the Gekko resin exchange column (G-REX) as an intermediate step, using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin. Operational experience has been gained at the Castlemaine Goldfields Ballarat gold mine. In near-continuous operation since 2008, the Ballarat plant treats unclarified concentrate leach solution. The extension of this technology to higher throughputs and more complex chemistry is discussed.RÉSUMÉ Afin d’optimiser la récupération de l’or dans des procédés complexes impliquant la lixiviation suivie de l’extraction électrolytique, Gekko Systems a développé la colonne Gekko de résines échangeuses d’ions (G-REX) comme étape intermédiaire, à l’aide d’une résine hautement sélective pour la récupération de l’or qui permet d’isoler les métaux contaminants. Gekko détient la licence exclusive pour la résine AuRIX®100 produite par Purolite, et la colonne G-REX a été spécifiquement conçue pour cette résine. C’est à la mine d’or Ballarat de Castlemaine Goldfields que l’expérience opérationnelle a été acquise. L’usine de Ballarat, en exploitation quasi-continue depuis 2008, traite une solution concentrée non clarifiée de lixiviation. L’extension de cette technologie à des capacités supérieures et à une chimie plus complexe est examinée.AURIX®100 RESINAuRIX100 resin is a crosslinked polystyrene alkaline resin developed by Henkel (Virnig, Mackenzie, & Adamson, 1996). The resin beads are off-white in colour and spherical, with a nominal size of 100% +600 µm. This resin is highly selective for gold and silver over many metals, by way of extracting precious metal–cyanide complexes from leach solutions with a pH of less than 11.5. The higher end of the pH scale produces the best selectivity according to the order of preference: Au > Ag > Hg > Zn > Ni > Cu > Co > Fe. Purolite produces the resin and Gekko Systems maintains licensing of AuRIX100 resin for use in its G-REX column, as part of its unique suite of gravity gold–handling equipment.Significant cost savings over carbon-in-solution (CIS) systems are realized with AURIX100 resin: approximately 4–12% in capital savings and 27–40% in operating costs (Virnig, Mackenzie, Katsikaros, & Gray, 2004). Additionally, AuRIX100 resin is not susceptible to fouling; that is, the resin does not load with inorganic salts or organic compounds that would affect the loading and extraction of precious metals. To counter any potential for fouling by inorganic salts, a dilute acid wash is periodically conducted in service on the resin to unblock resin pores."

Jan 1, 2017

By M. Kreuh

Crystalline Mg(OH)Cl and amorphous Mg2(OH)3C1 were successfully isolated from a hydrolyzed molten salt electrolyte sample in this work, It was found that the chemical form and crystallinity of the hydroxylchloride were controlled by the cooling rate of the molten sample when it was taken. Crystalline Mg(OH)Cl could only be obtained by cooling the molten electrolyte sample at a rate not faster than 0.6 °C/min, Upon more rapid cooling, the hydroxylchloride species precipitated as Mg2(OH)3Cl, The behavior of these solid hydroxylchlorides when contacted with fresh and non-hydrolyzed molten electrolyte at 550°C was also examined, It was found that the Mg(OH)Cl rapidly dissolved in the hot electrolyte and did not decompose into MgO at that temperature as would be expected from the literature, The dissolution rate of solid Mg2(OH)3Cl was found to be so slow by comparison that it resulted in the complete decomposition into MgO which thereafter was incorporated into the electrolyte as a suspended solid phase rather than dissolution.

Jan 1, 2004

By J. L. Feng, F. Zhang, S. K. Hu

"Cracking is one of the most serious damages in tunnel linings, which is often observed by in-situ inspection to tunnel engineering. It is difficult to better characterise for the deformations from continua to discontinua by the traditional continuum mechanics due to emerging of crack initiation, crack propagation, and coalescence, at several scales. In this paper, the process of failure that was from micro damage to macro crack in concrete tunnel linings under experimental load conditions, was quantitatively simulated by the combined finite-discrete element method (FDEM). Comparison of the simulating results with that obtained by the full-scale test of concrete lining under different loading conditions in the literature was respectively good agreed and shows that such FDEM technique is appropriate to model the continuousdiscontinuous problems. The present study indicates that the FDEM technique could be benefit to quantitatively evaluate the stability and damage level of tunnel lining system. INTRODUCTIONMost damage to tunnel linings is caused during the construction phase, which can emerge in a form of single macro cracks or even large-scale spalling. The cause of such damage is mostly the occurrence of, either impermissibly large contact stresses resulting from high thrust loads combined with production and installation tolerances in the segments resulting in a geometrical lack of fit (Maidl et al., 2012; Transportation Research Board, Basic Research and Emerging Technologies Related to Concrete Committee, 2006), or unallowable tensile/shear stresses appearing in the tunnel linings under complicated loading conditions (Ansell, 2010). Such a macro failure phenomenon may also be regarded to as a result of growth, coalescence, initiation of microcracks in tunnel linings due to the complicated loading action, and even potentially lead to an instability or collapse of the local or entire tunnel system. Much work has been devoted to investigate for the characters of micro and macro cracks, the influence factors of damage patterns, the settlement of a tunnel, the width, length and density of lining cracks, especially from classifiedly and qualitatively (Wang, 2010; Huang et al., 2013). However, the safety evaluation of tunnel is definitely required to not only inspect in situ, but further also quantify computing and analyzing for tunnel lining systems, so as to provide a global viewpoint of process of the tunnel deformation, which aims to help for subsequent decisions, e.g. controlling traffic flow or immediately repairing task. Additionally, the design of lining thickness and its structural analysis that is mostly determined by previous experience and similar construction examples is also needed to be improved."

Jan 1, 2015

By Norman O. Lotter, Lori Kormos, Greg J. Wilkie, Peter J. Whittaker, Johannes S. Stickling

"Assessment of opportunities to improve mineral processing performance in existing concentrators and in describing undeveloped orebodies is key to improving the business case of a mining company. This assessment has traditionally been performed using the distinct and separate inputs from Mineral Processing and Mineral Science.More recently, Process Mineralogy has been used to integrate these two disciplines. This trend has been driven by the need to develop and process more challenging ore deposits, and has been assisted by the availability of modern automated instruments. Together with the acquisition of a QemSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) from CSIRO in Australia, and with the use of a supporting SEM with EDX / WDX capabilities and an XRD, the development of Process Mineralogy at Falconbridge commenced in 1997.The sampling challenges in presenting a QemSCAN with representative sample material at the polished section level are significant, but have been effectively addressed. The full description of this aspect is beyond the scope of this paper.It is shown that, by use of this approach, the set nature of an orebody can be best exploited with selected flowsheet changes in a concentrator which address the generic characteristics of the orebody. In this way, the flowsheet provides a process that more effectively fits the mineral processing requirements of the ore. This leads to clear and tangible improvements in grade and recovery."

Jan 1, 2002

By G. B. Langford

UOCK bursts are a phenomenon about which insufficient is known. This l.~ statement has a twofold meaning. In the first place, far too many people, both inside and outside of the mining industry, are woefully ignorant of the whole subject, and secondly, as those who are face to face with the problem in the mines realize, our knowledge of rock bursts is inadequate. The first group embraces the general public, who have never been enlightened on the subject, and a great many geologists and engineers who have never shown more than a curiosity about it. Such technical men do not realize what a vital problem it is to our mining industries. They are usually thankful that bursting ground is not their problem, and leave it to those unfortunate enough to run into it. From such men one often hears the pious opinion that if proper mining methods were used there would be no problem. It is hoped that this paper will give these people a different viewpoint. Those in the second group deserve much credit for what they have done and are doing. They are fighting a large and difficult problem. In the pages that follow, I have tried to give a bird&apos;s-eye view of that problem, and suggest new ways in which it may be attacked.

Jan 1, 1941

By A. S. Eve

The detection of magnetic dykes by using magnetic variometers is the oldest application of. geophysics to mining, and is also one of the more simple and certain methods 0f locating such deposits. As a result of recent improvements in the instruments, it is now possible to find the dyke, deter-mine with magnetic variometers its strike and dip&apos;, with fair accuracy, and to estimate the approximate depth of overburden when there is no outcrop. The application of electrical methods may be used to distinguish mineral from diabase dykes. The authors have had an opportunity of making surveys with the modern Askania types of vertical and horizontal variometers over magnetic dykes in the Sudbury region. The interpretation of the results has been confirmed by diamond drilling in some cases, and by experiments over models. The variometers used were the standard form of Askania instruments (1). The sensitivity of the horizontal type was 17.2 gammas per division, and that of the vertical variometer double this quantity. To make a preliminary survey of the district, parallel lines were laid off two hundred feet apart running north and south, and readings were taken with the vertical variometer every 100 feet along these lines. This can be done very rapidly, and when an indication of a magnetic deposit is found, the readings may be taken every hundred feet, or less if the size of the deposit warrants smaller intervals. If the deposit is a vein or dyke, the readings along the adjacent lines immediately indicate the strike of the body. Thus the presence and strike of a magnetic dyke, whether of mineral value like the pyrrhotite and nickel deposits of the Sudbury district, or simply a worth-less diabase dyke, is simply and rapidly found.

Jan 1, 1932

By Sherwin F. Kelly

With the progressive exhaustion of ore deposits easily discovered by surface prospecting, the attention of scientists is being turned more and more to the employment of mechanical means for the location of ore bodies whose outcrops are not visible. The dip needle, the Eotvos Torsion balance, and various methods of electrical prospecting are illustrative of the modem tendency. Interest in the possibility of applying electricity to the solution of many of the prospector&apos;s problems dates much farther back than is usually realized. The first person to notice an abnormal intensity of electrical activity in the region of certain ore bodies was an Englishman, R. W. Fox, who experimented on the Cornwall copper and tin veins about 1830. Dr. Barus, in the United States, carried the early experiments a step further in his work on the deposits of Eureka, Nevada, about 1880. He made the very definite suggestion that the phenomena noticed would be of material aid to the prospector. Not until Professor Schlumberger, of the Ecole des Mines, Paris, took up the matter, shortly before the war, was any definite effort made to put electrical prospecting on a commercial basis. His work resulted in the establishment of sound principles and practicable field technique, for two distinct methods of prospecting.

Jan 1, 1924

By T. Patching

"Introduction The occurrence of coal was first reported in the Drumheller area in 1793 but it was not until 1912 that production of coal was recorded. In that year 13,000 tonnes were mined in the Drumheller area. Three years later the Drumheller mines ranked next in the Province to those in the Crowsnest and Lethbridge districts, with an output of 225,000 tonnes. By 1917 production had increased to 600,000 tonnes, moving Drumheller to second place in output in the province, second only to the Crowsnest district. It held this rank until 1960. Production, almost all from underground mining, rose to over a million tonnes a year by 1920 and remained between one and two million tonnes per year until 1954. Competition from newly discovered oil and natural gas, beginning around 1950 caused a steady loss of domestic coal markets, especially from underground mines. By 1960 Drumheller's production had fallen below a half a million tonnes per year and the field ranked third in output in the province, being surpassed by new stripping operations in the Castor field. By 1965 only a couple of producing mines remained in the Drumheller valley, and output was only about a quarter of a million tonnes per year(1). Throughout the life of the field production was seasonal, depending mainly on the domestic heating market. In 1979 the last mine ceased production. For the last several years of its operation it had remained open in the summers to provide tours for visitors(2). The Drumheller mining operations were located along or near the Red Deer River valley which is 300 to 400 feet deep, and extended from a few miles above the city of Drumheller to East Coulee, about 13 miles down the river in a south-easterly direction. Intervening mining communities existed for some years at Wayne and Rosedale. During the peak years of production some 2000 to 2500 miners and their families lived in these communities and the surrounding areas."

Jan 1, 1985

THE Michipicoten area, one of numerous iron-bearing "Archean" segments in the Shield, contains two main types of iron formation, a normal Keewatin-type, consisting of interbanded chert, siliceous magnetite and jasper, and, gradational to this, a carbonate-sulphide type which contains large de-posits of siderite and pyrite. The carbonate-sulphide type of iron formation bears a direct and intimate relationship to the volcanic development of the area; it there-by affords some insight into genetic problems of Archeanron formation in general. The purpose of this pa-per is to summarize the geological setting of Michipicoten iron formations and to briefly review genetic aspects of recent work in the area. GENERAL GEOLOGY in largely by assorted volcanics and sediments of the Michipicoten series and younger, regional granite masses. (Fig. 1). The Michipicoten series comprises a thick assemblage of mixed flows and pyroclastics together with elastic sediments and banded iron formations. The volcanics belong to the Andesite-Rhyolite Association, and characters-

Jan 1, 1961