Search Documents

By G. Ergin

The interactions taking place between Al-Mg alloys and the bed media during aluminum filtration are not yet well understood. These interactions were studied using the infiltration technique. The reaction interface was analyzed using different techniques such as SEM and TEM. Only spinel formation was observed at the interface regardless of the type of alumina and contact time. This paper discusses the results of the study.

Jan 1, 2004

By Grant D. Nicholas

This paper compares an integrated evaluation approach to decision-making with more traditional sensitivity analysis and Monte Carlo simulation. The primary objective is to highlight the differences in NPV that can arise from using these evaluation methods in a top down and bottom-up approach. Results from three resource scenarios, derived from sampling a "virtual" ore body (reality) on grid spacings of 75m, 50m and 25m, are analyzed and compared.

May 1, 2007

By P. R. A. Andrews

"Graphite is one of the most versatile of non-metallic minerals because of its diversified properties, for example: it is unctuous; it marks readily; burns slowly; is almost chemically inert; is flexible over a large temperature range; is a good conductor of heat and electricity; is hydrophobic; has a negative temperature coefficient of resistivity; has excellent weathering properties; tends to emulsify with water-in-oil; is readily soluble in iron; and after oxidative treatment, can exfoliate like vermiculite. These properties give rise to its major uses in lubrication, refractories, marking instruments, electrical products and paints.Flake graphite is the variety which commonly occurs in Canada; the provinces of Ontario and Quebec contain the deposits of economic significance, although graphite occurs in other provinces. The beneficiation of graphite has been the subject of many investigations at CANMET, thus reflecting graphite 's importance as an industrial mineral. Thirty-eight studies relating to various aspects of beneficiation were conducted between 1918and 1989anda review of some of the more important studies is presented. The information includes mineralogy, beneficiation methods and results; flotation parameters and reagent concentration data are presented in tabular form. By so arranging the principal data, the research worker and production metallurgist will be assisted in the evaluation of graphite ores from a variety of origins."

Jan 1, 1992

By J. A. Finch

Solvent-coated air bubbles in the Air-Assisted Solvent Extraction (AASX) process achieve the dual role of high solvent specific surface area and ease of phase separation. The thickness of the solvent film is of fundamental interest but difficult to measure directly in the process itself. As an approach interferometry (in the UV-vis region) was used to measure the time dependent thickness of a film formed by blowing an air bubble in kerosene-based solvents. The film was stabilized by the presence of 1.5 ppm silicone oil, as employed in AASX. The film appears to comprise two layers; an outer "free" layer of almost constant thickness and an inner "bound" layer which decreased in thickness with time. The bound layer is considered relevant to AASX. For a 20 mm diameter bubble blown in LIX/kerosene solvent the initial thickness was ~ 3 um which decreased over 10 minutes to a final rupture thickness of 500 nm. The bound layer thickness and time to rupture decreased with decreasing bubble size. Correspondence to prior indirect estimates of solvent layer thickness is examined.

Jan 1, 2006

By V. J. Hucka, J. H. Tu

"A computer model has been developed for evaluating the performance of truck and shovel operations in an open-pit mine. The data required for describing the haulage network are simplified and shift startup and ending procedures specific to any given mine can be incorporated into the model readily . The model uses a FORTRAN-based simulation language SLAM and can be tailored to the conditions and practices of a particular mine.The model is used to analyze truck and shovel operations, evaluate different haulage layouts in the planning stage, or compare the expected performance of alternative truck dispatching systems.Stochastic simulation is used to model the random variation in time required f or the individual activities. This gives a more realistic representation of the processes under study. Simulation runs show good agreement with actual performance. The model is especially useful for examining alternatives in equipment acquisition , haulroad design, truck-shovel allocation and dispatching methods. The results of such simulations provide a sound basis f or making major management decisions.IntroductionTruck haul age is widely used in open-pit mining operations. It is also the largest cost item in the operating costs of an openpit mine, in some cases accounting for an estimated 50% of operating costs(1) , Truck replacements, which are necessary from time to time, involve large amounts of cap ital. Increasing depth of mining and consequent increase in stripping ratios require additional capital investment in the truck-shovel fleet. The sharp rise in energy costs over the last decade has also contibuted significantly to an increase in truck fleet operating costs . All these factors have led mine operators to search for ways to improve the effectiveness of the truck-shovel fleet, in order to lower costs and maintain a profitable operation in the face of declining markets and increasing world wide competition.Control of truck haulage in an open-pit mine is usually done in one of two ways."

Jan 1, 1985

By Jack Craft

Local Environment Atmospheric conditions (or lack thereof) Drilling fluids are impractical Cuttings removal is a major concern Heat dissipation is a major concern Some tried-and-true mechanisms need air to function properly Gravity Low gravity means low downforce Microgravity means even less downforce Regolith Local dust may be highly abrasive Packaging for Spaceflight System mass is highly constrained The drill must fit within the spacecraft?s launch envelope Power is constrained

May 1, 2013

By Bruce W. Downing, Philip G. Claridge

"The availability of environmental data is a major concern in the development of an exploration project through the permitting and feasibility stages. The collection of these data should ideally start very early in a major exploration program. Although a large proportion of the environmental data can also be used for exploration purposes, (e.g. stream-sediment, soil, and rock analyses), environmental sampling will rarely have been initiated at an early date. For the Windy Craggy project, a major environmental concern is the potential for generation of acid rock drainage from waste-rock piles. The project is reviewed with respect to the environment of the deposit, deposit geology, mineralization and reserves, the sequence of exploration activities to the present, the potential for the development of acid rock drainage, the geochemistry and water quality, and the integration of exploration and environmental databases and their application to environmental planning. IntroductionIn the classical sense of exploration of a mineral deposit, the efforts throughout exploration are routinely directed at confirming the existence of the deposit and defining its extent, grade and continuity. Environmental issues are usually tackled separately, possibly by different personnel at a later date. When that is the case, an opportunity is lost to build, from an early date , a comprehensive database that (I) will satisfy the needs of conventional exploration and environmental monitoring, and (2) is usable as a predictive tool for environmental impact assessment.The concept of environmental geochemistry is not complex. The availability of environmental data is a major concern in the development of an exploration project to the feasibility and permitting stages. The collection of data should ideally start very early in any major exploration program. In many cases a significant proportion of the geochemical exploration data gathered early in the life of a project will also be used later for environmental purposes (e.g. stream-sediment, water, soil, and rock analyses). Rarely, however, will the data gathered in a geochemical exploration program provide information as complete as that attainable if environmental objectives had been considered in scoping the work.A knowledge both of local and regional geochemical processes can lead to a better understanding of environmental impacts. This understanding is the basis upon which good environmental management practices may be built. Geddes Resources Limited has undertaken a major study of the natural environment in the Windy Craggy area which includes geology, surface and underground waters, soils, stream sediments, glaciers and geomorphology (Geddes Resources Limited, 1990). This paper deals with the building and integration of the exploration and environmental databases."

Jan 1, 1993

By Bruce Macdonald

Operational monitoring of slope stability can be achieved by space based InSAR monitoring platforms. Natural and man-made rock slopes are monitored using a novel stack-based InSAR method that exploits both persistent point scatterers (PS) as well as coherent distributed scatterers (DS) such as areas of pavement and sparsely vegetated surfaces. The new method, Homogenous Distributed Scatterer (HDS)-InSAR identifies InSAR targets by using adaptive multilooking of statistically homogenous pixel neighbourhoods combined with thresholding the differential temporal coherence of each target candidate with respect to its surroundings. HDS-InSAR preserves PS and therefore forms a direct generalization to our proven DualScale-PSI method. The density of HDS exceeds that of PS by more than an order of magnitude often providing essentially continuous coverage over urban and industrial landscapes featuring a mix of infrastructure with mostly bare soils or rock surfaces. The improved coverage enables better definition of surface motion and underlying geology, which will lead to superior interpretation of the geophysical mechanisms causing the surface deformation, e.g. through improved integration with 3D deformation modeling. We illustrate the performance of our new HDS-InSAR method compared to DualScale-PSI using displacement results from Vancouver, Canada; Bingham mine, USA; and the Palabora mine, South Africa.

Jun 1, 2012

By M. E. Hurst

SINCE 1934 there has been a marked revival of interest in the Porcupine district, especially in the eastern portion of the area, where exploration on the property of Pamour Gold Mines has indicated the presence of extensive gold-bearing deposits. Owing to the prevalence of overburden and the limited amount of exploratory work that has been done, little information is available as yet concerning the distribution and structural relationships of the rocks in the area to the east of Porcupine lake. In order to throw some light on the structural conditions in this section, a brief discussion of the sequence and character of the formations in the better known, producing section of the camp has been included. It should be emphasized that this paper is a preliminary study and that, consequently, the conclusions expressed should not be regarded as final. The writer wishes to acknowledge his indebtedness to P. C. Benedict, whose study of the geological relationships on the Foley-O'Brien property has made possible a fuller understanding of the structure in the central portion of the area. The writer also wishes to express his appreciation of the information and facilities placed at his disposal by R. M. Macaulay and C. D. Stevenson, of Pamour Gold Mines, and by A. Bell, of Noranda Mines, Limited.

Jan 1, 1936

By R. Clarkson

"Free gold particles occur in many base metal and precious metal mines throughout the world. Due to the high density and malleability of gold, large circulating loads of free gold particles can build up over time in grinding circuits. This gold is often deposited in unintended traps throughout the mineral processing system.These unidentified free gold deposits represent a serious security risk as well as an inaccessible inventory of gold. Deposits of free gold particles often remain undetected by mine management until they are accidentally discovered while repairing mill equipment.Nuclear tracers have been used to determine the free gold recovery efficiency of gravity recovery equipment, drills, and sampling equipment (Clarkson, 1994, 1995; Walsh and Rao, 1986; Walsh and Kelly, 1992). In November, 1993, the author inspected the grinding circuit at La Mine Doyon in Rouyn-Noranda, Quebec and made recommendations to recover coarse gold and to eliminate gold traps from the circuit. In 1995, the author salted mineral processing circuits with radioactive gold particles. The gamma and X-ray radiation from gold’s nuclear isotope (Au198) were detected through steel, in pipes, and in moving equipment using scintillometers. The radiotracers proved to be a safe, rapid and accurate method of identifying gold traps and improving security.Nuclear TracersWhen particles of gold are placed in a nuclear reactor, some of the gold atoms (Au197) absorb another neutron in their nucleus to form gold’s radioactive isotope (Au198). In the process of radioactive decay, this isotope emits high energy gamma rays and X-rays which are easily detected (even through steel) with scintillometers.Radioactive gold (Au198) has a very short halflife of 2.7 days. At the relatively low activity levels used for tracing, the particles remain detectable with a small hand-held scintillometer for about 10 to 14 days. After 14 days the irradiated gold is close to background levels and within two months it is essentially non-radioactive. The radiation has no effect on the recovery characteristics of the gold particles. The gold radiotracers are very safe due to their very low level of radiation, short half-life, and their inherent physical and chemical stability. However, the use and possession of even mildly irradiated gold is strictly licensed and regulated."

Jan 1, 1997

By M. Leahy

"Very little is known about the large scale fluid dynamics and associated distribution of copper in an operating electrowinning cell, yet they will have a major influence on mass transfer and plating quality. The CFD model in this work is used to simulate an entire EW cell with 60 cathodes and 61 anodes, or 121 anode–cathode pairs, elucidating for the first time the three-dimensional (3D) flow and copper distribution in an industrial cell. Two methods for the distribution of electrolyte are modelled:1. Downcomer method: electrolyte is fed by a downcomer at one end of the cell, overflowing at the opposite end.2. Manifold method: a horizontal manifold pipe runs the whole length of the cell and feeds electrolyte via small holes in the top of the manifold pipe.The recirculation that develops within each anode-cathode pair, driven by oxygen bubble generation on the anode, is similar to that seen previously in two-dimensional models of single anode–cathode gaps. However a more complex 3D flow recirculation is established, which involves flow of electrolyte down the side gaps (being a path of low resistance for return flow) as well as the usual return flow down the cathode side of each pair gap. The bubble-driven flow is not influenced by the mode of electrolyte distribution.The electrolyte flow due to the manifold and downcomer is somewhat secondary to the bubble driven flow. In the case of the downcomer distribution mode, the high injection velocity causes a very turbulent flow in the first 1–2 m down the cell from the downcomer, with several large vortices developing. This may lead to some sludge particles being entrained into the bulk of the cell.In the manifold pipe case, the jet from each hole is dissipated very quickly, within the first 10–20 cm. The jets are directed into the downward flowing zone of the bubble-driven recirculation, which leads to unstable and periodic behaviour on a large spatial scale.In both the manifold and downcomer cases, there is a marked two-zone vertical stratification in copper concentration."

Jan 1, 2016

By Nathan Deisman

Coupled reservoir geomechanical simulations have become a key component of caprock integrity assessments for SAGD operations. This work demonstrates the differences of stress evolution when considering coupled versus uncoupled reservoir simulation. Coupled simulation involves the use of a reservoir and a geomechanical simulator with feedback to each simulator to update reservoir or geomechanical variable (permeability, porosity, relative permeability, pressure, temperature, saturations). Uncoupled simulation only passes the pressure and temperature to the geomechanical simulation with no reservoir simulator updating. Therefore, it is possible to complete uncoupled simulations exclusively with no knowledge of geomechanical flow property evolution. However, it is important to understand the differences between the stress evolution in each model for caprock integrity analysis. A single geological model was selected and parametric analysis was completed while varying the geomechanical the production injection pressures (1600 kPa, 1900 kPa, 2200 kPa) for a reservoir with an initial pressure at the injector of 1300 kPa. The results of the six uncoupled and coupled models are compared through the changes in mean stress, shear stress, and strength with focus on geomechanical assessment of caprock integrity.

Jun 1, 2012

By Mark Rantapaa

Measurable improvements in throughput have been documented at Barrick Goldstrike due to increased ore fragmentation through efficient drilling and blasting techniques. A decrease in throughput at the Autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the Open Pit and Process areas worked closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of actually improving throughput in future years, despite the projected harder ores. A series of tests were conducted to determine if adjustments to drilling and blasting could positively influence throughput. Better fragmentation and a subsequent increase in mill throughput were achieved through the use of: 1) Electronic caps for more precision and flexibility, as well as for allowing extremely fast shots. 2) Explosives with a higher velocity of detonation (VOD), to provide for improved shock energy. 3) Improved distribution of the explosives by decreasing pattern spacing. Early tests indicated a significant increase in throughput when processing identified harder ore. It is anticipated that the total process throughput (hard and soft ore) will increase by six tph in 2003 due to the improved fragmentation of the hard ore. Barrick Goldstrike?s D2M initiative includes roaster ?hard ore? (BWI >17), as well as autoclave ?hard ore? (BWI >15). Approximately six million tons of D2M material is expected be shot in 2003, a relatively small amount compared to the 150 million tons to be mined. The benefit of additional ounces produced should far outweigh the additional drilling and blasting costs.

May 1, 2003

By Carricajo T., S. Nazari

This paper discusses a unique dynamic solution for optimizing comminution area in real time. The proposed technology is a combination of model predictive controller, optimization methods and real-time digital twin for mineral processing. For grinding area, the ultimate goal of an effective control strategy is to maximize the mineral processing, reduce energy consumption and stabilized size classification. To have a continuous and effective comminution operation, a reliable control system that minimizes the need for human intervention is necessary. The implemented advanced control strategy for comminution area consists of two layers in hierarchical structure. The lower layer objective is to stabilize the process stabilization using model based predictive controller (MPC) technique. The unique MPC used in this layer is called BrainWave™ chosen for its robustness, convergence and delay handling; furthermore, the developed platform offers stable and repeatable solution and has short implementation time. The upper layer is a supervisory control, which sends the preferred process operation points to the lower layer to drive the process towards optimal performance. The goal of this layer is to optimize the process targets, as well as making decision. To increase process performance, automatic ore characteristic adaptations are implemented in this layer. A digital twin of comminution area is built in the second layer that runs amongst the process in parallel. By communicating, the process data in real time, a virtual densitometer is built that is being used in our advance process control strategy. Our control strategy has been developed, tested and implemented in various areas of a copper concentration plant. The targets for implementing advance process control are usually increased throughput, decrease energy consumption and variability reduction in particle size distribution. Overall, the results showed in different mine sites are increase throughput between 2 and 5%, specific energy consumption reduction about 15% and process variability reduction up to 60%. In this paper we discuss the results of the recent implementation of this technology on Minera Los Pelambres, Minera Collahuasi and CAP Minería. Their concentrator plants have installed control systems with the most updates optimization features, for SAG mill, ball mills and thickeners.

Jan 1, 2019

By Naizhong Xu

During the past 30 years, fully mechanized caving mining has played a positive role in the improvement of the efficiency of coal production, but which has also had a great influence on the mining environment, especially to environment damage of shallow mining areas in the central and western regions of China. The surface subsidence parameters are the basis of the surface environment evaluation and governance. During 1980~1990s of the last century in China, fully mechanized mining subsidence laws were researched more fully, however, since coal caving technology is affected by many factors, and researches on its mining subsidence laws (parameters) were found to be grossly inadequate. Through actually observed in recent years, it is considered that coal caving mining subsidence laws (parameters) can use fully mechanized mining law (parameters) for reference. Based on fully mechanized mining laws (parameters), this paper reveals the similarities and differences of the surface subsidence laws between fully mechanized caving mining and fully mechanized coal mining, which can guide the work of coal mining under buildings, water bodies and railways in new mine area and mine collapse governance.

Aug 1, 2013

By R. Pakalnis, H. Miller, Madill. T.

"This paper describes a methodical approach to the estimation of the orientation and the magnitude of in-situ stresses. The study was performed at the Ruttan Mine, Sherritt Gordon Mines Ltd. , a 6,000 T.P.D. underground operation, located in northern Manitoba, Canada. It involves an initial estimate to be made based upon: structural interpretation • virgin stress measurements conducted in other areas (world wide, regional)The verification of the prevailing stress regime was made by conducting CSIRO hollow inclusion(1) overcoring measurements. The current cost for a virgin stress determination is about $7000 per measurement(2) and the difficulty encountered in attaining a good reading is high. This paper will describe the analytical procedures employed at Ruttan in evaluating the in-situ stress magnitude and orientation based on three overcore tests. It is proposed to perform an additional six measurements in order to verify the following results:Vertical stress = av (MPa) = 0.027 by depth (m)Major principal stress = o! """" 2.5 xav (340°/-20°)*Intermediate principal stress = a2 - 1.2xav (070°/0°)Minor principal stress = a3 """" o.8xov (160°/-70°)IntroductionThe Ruttan Mine of Sherritt Gordon Mines Ltd., a 6,000 T.P.D. underground operation, is located in northern Manitoba, Canada (Fig. I). The Ruttan copper-zinc orebody is a multi-lensed, steeply dipping (70 degrees) en-echelon deposit. Individual lenses have a maximum strike length of 350 m with widths varying from 7 m to 61 m. The mining method is o pen stoping with delayed backfilling and extends from surface to 860 m below surface."

Jan 1, 1985

By T. Y. Chong, J. A. Folinsbee

Since milling began in 1909, the PJV Dome mill has been expanded several times, to the current throughput of 11,500 tonnes per day. PJV recovers free gold using crushing and grinding followed by gravity concentration. The remaining gold in the gravity tails is recovered by cyanide leaching followed by Carbon-In -Pulp processing. Prior to 1993, cyanide tailings were impounded in the tailings pond where cyanide was allowed to degrade naturally. Effluent was discharged seasonally during the summer and early autumn to maintain the water balance. In 1993, an Effluent Treatment Plant (ETP) was designed and constructed for the purpose of removing dissolved metals and suspended solids. In 1997, an INCO SO2/Air cyanide destruction process was added to the ETP. Even though the ETP was successful in meeting the cyanide, metals and total suspended solids (TSS) discharge limits, often the treated effluent failed to pass toxicity tests. Following successful laboratory and plant scale testing, the addition of the chelant EDTA (ethylene diamine-tetra-acetic-acid) was commenced in the 1999 operating season. To date, discharged effluent has passed all toxicity tests. This paper describes the evolution of the ETP from its early conception to the various phases of upgrade needed to meet the MISA discharge limits.

Jan 1, 2005

By David J. Kerr, Robert Mason

"From1927 to1989, the Hornemineproduced53.7 Mt of ore grading 6.1 g/t Au and 2.2% Cu from two large volcanogenic massive sulphide deposits composed primarily of pyrrhotite, pyrite and chalcopyrite. The ore bodies were hosted by a package of chlorite-sericitealtered epiclastic rhyolite tuffs which were deposited in a narrow palaeo-graben located on the flank of a major felsic volcanic centre. M ineralizingfluids percolated upward through the permeable footwall rocks and were further focussed along syn-volcanic, graben-bounding faults. Sulphides were deposited by a process of sub-seafloor replacement of the rhyolite tuffs.Gold-copper-(zinc) mineralization, including ore zones mined between 1985 and 1989 as the REMNOR ore zones, is present throughout the 900 m of felsic volcanic stratigraphy at the Horne. All the deposits were formed by syn-volcanic hydrothermal processes active during felsic volcanism. There is no evidence to indicate that any economic gold mineralization was introduced by a post-volcanic hydrothermal episode.RESUMEDe 1927 a1989, /amineHorneaproduit53.7 Mt de minerai avec une teneur de 6.1 g/t Au et 2.2% Cu provenant de deux grands amas de sulfures massifs volcanogeniques comprenant esentiellement de la pyrrhotite, de la pyrite et de /a chalcopyrite. Ces gites font partie d'une séquence de tufs rhyolitiques epiclastiques chloritises et sericitises qui ont ere déposes dans un paleo-graben étroit situe sur le flanc d' unimportant centre vo/caniquefelsique.Lesfluides mineralises ont circule de bas en haut a travers /es roches perméables sous-jacentes; ils ont été également canalises par les failles syn-volcaniques en bordure du graben. Les sulfures se sont déposes par remplacement des tufs rhyolitiques immédiatement et sous /e plancher océanique.Les zones minéralisées en or et cuivre (±zinc) - y compris celles qui ont ere exploitees au cours de l’opération Remnor (1985-1989) - se retrouvent, sans discontinuité, à travers les roches volcaniques felsiques dont l' epaisseur atteint 900 m. Ces gites se sont formes par le biais d' un processus hydrothermal qui ag issait pendant le volcanisme felsique. II n'y a aucune évidence de minéralisation aurifère d'importance économique qui soit postérieure a l' activité hydrothermale syn-volcanique."

Jan 1, 1990

By Himanshu Dehra

The pre-fabricated outdoor rooms are often utilised near the mines and construction sites for office purposes. The paper has presented modelling and simulation results of the integration of commercially available glass coated photovoltaic (PV) energy technology and solar ventilation technology into a pre-fabricated outdoor room. The pre-fabricated outdoor room has been setup at Concordia University, Montréal for full scale testing of the glass coated PV modules with solar air ventilation. The computer simulation model has been developed for PV modules installed on a double wall wooden frame in an outdoor room based on its preliminary field testing. The testing apparatus was a wooden frame assembly of double wall with solar air ventilation: two adjacent glass coated PV modules, air column and plywood board filled with polystyrene. The measurement data collected from various sensors were: solar intensity, ambient air temperature, room air temperature, electric power, surface temperatures of PV modules and plywood board, air velocities and air temperatures in the air column. The enhancement in the air velocity of the air column was achieved with an exhaust fan fixed in an outdoor room. The simulation model is used to perform the two dimensional energy analyses with applied one dimensional solution of steady state heat conduction equations. The simulation model is based on conjugate heat exchange paths with network boundary conditions of convection, radiation heat exchange and solar air ventilation heat transport. The model parameters are based on measured values of ambient air temperature, room air temperature, air velocity at outlet of air column in double wall, electric power and available solar intensity. The model has predicted fairly well energy performance of glass coated PV modules with solar air ventilation installed on a wooden frame. The model is also useful for predicting heating, ventilating and air-conditioning (HVAC) requirements for the pre-fabricated outdoor rooms.

May 1, 2007

By P. Ashtari

Influence of Sr and Mn single and combined additions on the modification of the Fe-containing intermetallic compounds and mechanical properties of Fe-rich AA319 aluminum alloys have been investigated, The microstructural features e,g, morphology of the Fe compounds and eutectic Si has been correlated to the mechanical properties, It was demonstrated that modification of the Fe compounds from the platelet ß-Al5FeSi to the Chinese script a-Al8Fe2Si compound improves the UTS and elongation of the alloys by 10.3% and 83.9%, respectively. Moreover, the simultaneous modification of the Fe compounds and eutectic Si increases the UTS and elongation of the alloys by 15,3% and 116,1%, respectively.

Jan 1, 2005