Search Documents

By Narasimha Mangadoddy, Teja Reddy Vakamalla

"Vertical hydrocyclones are very common in most of the comminution circuits. Inclined cyclones are also found for specific mineral processing applications. In this work, Computational Fluid Dynamics (CFD) technique and experiments are used to find the reasons behind the inclinations effect on hydrocyclone performance characteristics. The water and silica slurry experiments are conducted with 75 mm hydrocyclone at different inclined positions (0-600) to the vertical plane. Corresponding two-phase numerical simulations are performed with Volume of Fluid (VOF) model coupled with Large Eddy Simulation (LES) turbulence model. Multiphase simulations are carried out with Algebraic Slip Mixture model modified with lift, drag forces and Newtonian rheology model corrected with fines for various feed solids concentration. A raise in the under flow solids percentage, cut diameter and a reduction in the water split is observed with the inclination. Electrical Resistance Tomography (ERT) and High Speed Video (HSV) data is used to cross validate the inclined cyclone’s CFD air-core and solids concentration data. Predicted efficiency curves are found in a close agreement with experiments for all the inclinations. Comparison of experimental and predicted flow data clearly follows trend with the literature. Key words: Hydrocyclone, CFD, ERT, inclination, water splitINTRODUCTIONHydrocyclones are devices used to separate or classify particles based on particle size difference in the water medium. Their usage is very wide in chemical, petroleum, mineral and bio industries due to its structural simplicity, high throughput, small volume, low cost and maintenance. Cyclone mainly consists of a cylindrical section followed by a conical section attached to a single feed inlet and two product outlets named vortex finder and spigot. It works on the principle of centrifugal sedimentation. The slurry is fed tangentially to the hydrocyclone, in which larger particles are moved towards the wall and separated by centrifugal forces to the underflow. Smaller size particles follow liquid due to drag forces to the overflow. With its simple structure, the flow behavior inside the hydrocyclone is quite complex. Vertical cyclones are common in practice in most of the comminution circuits. Horizontal cyclones can be found in extreme cases which are for installation convenience rather than for process reasons. Inclined cyclones are also present for specific mineral processing applications. In coal preparation plants, dense medium cyclones are operated near to horizontal inclination of 20 degrees to allow large spigot sizes for sinks removal, self-drain of contents during shutdown. In the phosphate removal, dense medium cyclones are inclined with an angle between 0-90 degrees for better separation of ore and tailings (Liu Feng et al., 2006). Even in the clusters, hydrocyclones are mounted with an inclination around the feed distributor for uniform distribution of slurry and under flow collection. It is believed in mineral processing industry that inclined cyclones would fetch the benefit in number of ways while classifying the material by size. Gravity influences the cyclone performance through the air core size and position variations in large cyclones. It also favours the cyclone operation at coarser cut points without varying any other design and operating parameters. Minimizing fines misplacement to underflow can be achieved with inclination."

Jan 1, 2016

By L. Chunpongtong

The Athabasca oil sands mineable resource is located in northeastern Alberta, Canada. In oil sands mining, the ore zone is regulated to have a minimum mining thickness of 3 m and a cutoff grade of 7 wt.%. The current algorithm that is widely used to flag ore zones and waste zones tends to overestimate oil reserves and causes low-grade ore to be processed. This paper presents the development of a more complex algorithm that is more representative of the actual oil found during operations and that can prevent low-grade ore from being sent for processing.

Jan 1, 2014

By G. W. Harris, P. Mousset-Jones, J. Daemen

"To minimize ore dilution induced by blast movement in surface mines, it is necessary to quantify such movement. This will enable more accurate location of the grade boundaries beneath the surface of a blasted rock pile before excavation. A method has been developed and tested to accurately measure the direction and magnitude of subsurface blast movement. This technique uses a cesium vapour gradiometer and a real-time, differentially corrected GPS system to locate pre- and post-blast position of magnetically enhanced target objects placed within blastholes inside a bench. The procedure developed does not require the blasted rock to be disturbed, and the movement information is available within a sufficient time to allow for modification of the selective mining boundaries for each surveyed blast. It was found that the maximum depth of target detection was 18 m, with the overall accuracy being measured as ±1 m (horizontally) and ± 1.2 m (vertically). IntroductionOre dilution is a critical concern for many mining operations. In some instances, it may be the cause of considerable mineral loss. Where the mineralization is finely grained, sedimentary and disseminated in nature, and exhibits no clearly defined visual ore/waste boundary, there is a heightened possibility for ore grade dilution. In most modern open pit gold mines, it is economically desirable to minimize dilution in the production process through the practice of selective mining by defining pre-blast ore digging boundaries, called digging polygons, on the preblast bench area. The polygons’ positions are defined by sampling the production drill holes, with the resultant assay and survey data being used to estimate the areas of specified grade content within the bench. Once the ore is blasted in the bench, the pre-blast locations of these digging polygons are flagged as designated areas on the broken ore pile. The purpose is for the loader operator to be able to recognize which areas of blasted rock are to be sent to the appropriate processing facility or to the waste dump."

Jan 1, 2001

By Erwin L. Zodrow

"IntroductionThrough an extensive coal sampling project in the Sydney coalfield of Nova Scotia during 1981 - 1984 involving a majority of the mineable coals (Zodrow, 1985, Fig. 1), a sizeable inventory on trace, minor and major metals was established. In this paper, results of studying the inventory are summarized, concentrating mainly on the relationship that exists between metal variations and thickness of coal channel samples (i.e. trends) and on explaining the trends in geochemical and sedimentological terms. As an over-all conclusion the Everglades peat of Florida is proposed as a modern-day analogue to Upper Carboniferous peat swamp development that took place in the Sydney Basin.Data InventoryFor this study 17 channel samples were cut , 8 cm to 14 cm channel width and 8 cm to 10 cm depth, from 10 successive coals which in stratigraphically descending order are as follows: Point Aconi (3), overrider Lloyd Cove (2), Lloyd Cove (2), Stubbart (2), Harbour (4), Backpit (I), Phalen (,I), Shoemaker (1) and McAulay (I), where bracketed values signify the number of channel samples cut from a seam (Zodrow, 1985, Fig. I). Each channel sample was subdivided by 15 em incremental length yielding a total sample size of 137 for analysis. By appropriate modern techniques these samples were analyzed to determine concentration levels for 32 chemical elements and ash content, the average results of which are presented in Table 1.Tests were also made for Pd, Pt, Ga, Nb, Cd, Cs, Sm and W but their concentration levels in many instances hovered on the lower detection limits that were used and on this accounts are excluded from discussion. Ashing, when necessary for the determination of concentration levels, was done for 12 hours at a temperature not exceeding 450°C. Concentration levels for the elements are reported in reference to whole-coal or whole-coal equivalents and discussed on this basis. In the course of the analyses, lower detection limits received careful attention."

Jan 1, 1986

By P. Chryssanthakis

"The aim of this study is to give a better understanding for the behaviour of the composite material RRS and the synergy effect of its components while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10 m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. The newest part of the lower part of the Q-chart gives more information on required support compared to older Q-system versions. The RRS can be described as a three part composite material with the 3rd component being the reinforced concrete beam (with no fibers) and with steel rebars that are placed in groups and sprayed with pneumatically applied shotcrete in layers. The RRS usually have a total thickness varying between 0.20 and 0.50 m and a width between 0.25 and 0.60 m respectively. They are placed at different distances along the tunnel axis depending on the rock mass quality.In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. This was done by writing a FISH subroutine which is implemented in the discontinuous numerical code Universal Distinct Element Code (UDEC) that takes into account the characteristics of the reinforced beam (height, width, number of steel rebars, and spacing) in the calculation process. A rather extensive parametric study has been run by using the same key input rock mass parameters and in situ stresses (?H/?v = 0.5), and changing only the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam.The results show that: a) the S(fr) is almost overloaded in the first 4 hours after application in both tunnels; b) on the S(fr) and steel rebars, the stresses, axial and shear loads, as well as moments are decreasing after 16 hours and 28 days; and c) the bolts loads are increasing with time. The observed reduction in stresses and loads in both the S(fr) and reinforced beam is surprising. A possible explanation is that tunnel arches are self-supported to a lesser extent as time progresses due to redistribution of stresses in the nearby rock mass through the radial bolts. The loads in radial bolts are increasing by almost 25%. This can be seen from the overall results as we observe an increase in maximum principal stresses, displacements, shear displacements along joints and hydraulic apertures compared to tunnel baseline that has no support of any kind."

Jan 1, 2015

By I. Lackey

In 2004, Zinifex Budel Zink commenced testing with the objective to increase the precipitation of aluminium in the iron purification stage of its hydrometallurgical zinc circuit, without the use of expensive reagents. Findings from the literature applied to the leach circuit at Zinifex Budel Zink demonstrated that aluminium removal from the leach circuit could be increased by lowering the ferric concentration and acidity in the vessels where jarosite precipitation occurs. An associated increase in copper precipitation was mitigated by limiting the extent to which the ferric concentration was lowered in the vessels where jarosite forms and lowering the ratio of copper to aluminium in the solutions entering these vessels.

Jan 1, 2006

By T. E. Warren, K. W. Bowles

"IntroductionTHE PROBLEM of producing synthetic liquid fuels from coal and other raw materials is of increasing importance in Canada as well as in the United States. This is due, to a large extent, to the continually increasing demand for gasoline and other liquid products which are now obtained solely from petroleum. The United States has reached a position where domestic supplies of crude petroleum must be augmented by imports and Canada is still a long way from self-sufficiency. In the event of war, there might well be an immediate need to find supplementary sources of liquid fuels. It is, therefore, expedient to consider alternative sources of production now -well in advance of the time when supplies of petroleum may prove inadequate to meet requirements.The purpose of the present paper is to give a short review of the history of liquid fuel production from coal, to describe briefly the research sponsored by the Federal Government on the coal hydrogenation process, and finally to evaluate the present status and future trend of the synthetic fuel industry, with special reference to necessary research work.History of the Oil-From-Coal IndustryThe history -of coal liquefaction began in 1913, in Germany, with the work of Frederick Bergius. His first approach to the subject was not deliberately planned."

Jan 1, 1952

By V. I. Birss

Planar solid oxide fuel cells (SOFCs) offer great promise as stationary power generation devices, primarily due to their flexibility in terms of fuels, high energy conversion efficiency (when both electricity and heat are captured), and their relatively low fabrication costs. However, the anode performance can be compromised by such factors as exposure to certain sulfur-containing fuels and the deposition of coke when using hydrocarbon fuels. In terms of the cathode, its performance is limited primarily by the slow kinetics of the oxygen reduction reaction, while its lifetime can be negatively affected by factors related to the corrosion of currently used stainless steel interconnect materials. This talk will present an overview of these challenges and some possible solutions to these problems. The presentation will also focus on how electrochemical methods can be used to evaluate and improve the performance of SOFC anodes, cathodes, and interconnect materials. In addition, recent promising research efforts directed towards performance enhancement of SOFCs through the use of nanoscale electrocatalysts will be discussed.

Jan 1, 2005

By Jing Li, Weiqiang Lai, Joe Zhou, Jiezhen Ma, Shuibo Chen, Ashele Copper Company, Feng Gao, Guofu Feng

"Copper-zinc ores often contain gold and silver, which can be recovered into copper concentrate by flotation as by-product. The challenges for operations that produce copper, zinc, gold and silver are the separation of copper and zinc and the low grade of precious metals. Ashele copper-zinc ore in north China contains 2.38% Cu, 0.69% Zn, 0.21 g/t Au and 18.10 g/t Ag and the plant produces copper and zinc concentrates, with gold and silver being recovered into copper concentrate. Copper occurs mainly as chalcopyrite and Zn occurs as sphalerite. Copper is well recovered with a recovery of over 94%. However, the recovery of Zn is substantially low (around 50%) due to fine grain size of sphalerite. In addition, gold recovery is much lower than expected and only 33% of gold in the flotation feed was recovered. The grade of gold in copper concentrate is also lower than the required payable grade (1.0 g/t). To determine the cause for lower Zn and Au recoveries, a plant survey program was conducted on the operation. The information acquired shows that the loss of Zn was mainly in the copper concentrates (accounting for approximately 38% of the head assay); of which, 24% was liberated, 8.5% was associated with chalcopyrite and 4.6% was associated with pyrite, indicating that the separation of copper and zinc was the main cause for the Zn loss, with liberation being the second cause for Zn loss. Future effort in improving Zn recovery should be focused on the separation of zinc from copper. Gold in the ore occurs as both microscopic gold and submicroscopic gold, accounting for 36% and 64% of the head assay, respectively. Microscopic gold occurs mainly as native gold and electrum; it is relatively coarse with a grain size of 10 to 240 µm and a large portion can be recovered by gravity. Submicroscopic gold was mainly carried by pyrite (accounting for 38%), and to a less extent, by tennantite (15%) and chalcopyrite (10%). Gold in sphalerite is nominal (1%). It is suggested that more coarse gold and tennantite be recovered and a gold recovery increase can then be achieved to obtain a copper concentrate with over 1.0 g/t Au through flowsheet optimization. Gravity concentration should be investigated and may be worth added into the existing flowsheet to maximum the gold recovery and grade.INTRODUCTIONCopper-zinc ores containing gold and silver is a subtype of polymetallic sulphide ores. Unlike porphyry copper sulphide ores and iron-oxide copper-gold ores, this type of ores often contains substantial amounts of zinc and lead. Polymetallic sulphide ores are mainly distributed in Canada, such as at the LaRonde and Horne deposits. Other examples include Mt. Morgan in Australia and Boliden in Sweden. Globally, production and reserves from gold-rich VMS deposits account for 1370 t gold. This is equivalent to 1% of the world production and reserves, whereas the Canadian total for gold-rich VMS deposits is 870 t, representing close to 10 % of Canadian production and reserves (Gosselin & Dube, 2005a, 2005b). Flotation is the principal process for processing the copper-zinc sulphides ores, for subsequent smelting, roasting, or hydrometallurgical treatment. Oxidized copper-zinc ores can also be processed using leaching technology. For example, at LaRonde operation (a Cu-Zn-Pb ore containing 3-4 g/t Au and 60-100 g/t Ag) the flowsheet consists mainly of a copper flotation circuit and a zinc flotation circuit followed by a cyanidation process of flotation tails. The precious metals are recovered with copper concentrate, zinc concentrate and cyanidation of zinc tails via Merrill Crowe precipitation (Zhou et al., 2005)."

Jan 1, 2016

By S. Harvey

The McArthur River deposit is a structurally-controlled unconformity-related uranium deposit. The mineralization is situated at the intersection of a pronounced fault zone, referred to as the P2 fault zone, and the unconformity between Paleoproterozoic Wollaston Group metasedimentary rock and Paleoproterozoic to Mesoproterozoic Athabasca Group. Mineralization is variably hosted within the Athabasca Group fault wedge and the faulted basement, consisting of twelve zones covering a strike length of 2,700 m. The main P2 fault zone consists of several reactivated foliation-parallel faults containing narrow seams of graphitic clay gouge that are separated by highly cleaved, graphitic wall rock. The mine grid east-dipping P2 fault zone is characterized by reverse offset of the unconformity surface. It varies from a single discrete fault to splay offsets consisting of two to three individual splays. The combined vertical offset along the P2 fault zone is a maximum of about 80 m. The fault has emplaced a wedge-shaped sequence of Wollaston Group metasedimentary rocks into the Athabasca Group. Foliation-oblique faults occur throughout the McArthur deposit trend. Steep east-northeast trending faults generally exhibit apparent oblique dextral sense of shear. Less common, and possibly conjugate, are steep faults trending east-southeast with an apparent sinistral sense of shear. Offsets are generally less than 10 m on these structures. South-trending and shallow west-dipping brittle faults with offsets less than 1 m are also observed while rare steep, north-trending faults are also noted locally and played a critical role in development of the Zone 2 basement-hosted mineralization.

Jan 1, 2020

By Rick J. Chalaturnyk

In Alberta, oil sands bitumen is utilized for synthetic crude oil production by surface mining, bitumen extraction followed by primary (coking) and secondary (catalytic hydrotreating) upgrading processes, or by catalytic hydrocracking and hydrotreating replacing the primary and secondary upgrading processes. Oil sands tailings, composed of water, sands, silt, clay and residual bitumen, is produced as a byproduct of the bitumen extraction process. Several processes have been proposed for the treatment of oil sands tailings, resulting in different recovered water characteristics, consolidation rates and consolidated solid characteristics, which may have effects on the performance of the overall plant operations. A process for the same purpose has been developed by treating the oil sands tailings with CaO lime and CO2 and thickening it using a suitable thickener. In this process a release water of acceptable properties is recovered in a short retention time, which makes it possible to recycle the recovered water, probably after a reconditioning treatment, as warm as possible to improve the thermal efficiency of the extraction process. The paper presents the theory and laboratory results for the CaO and CO2 thickening of low temperature flotation tailings. The water release rates, segregation potential of the thickened underflow and chemistry of the release water are shown and discussed. It is suggested that in using the proposed process, the thickened tailings underflow can be disposed for further consolidation, or combined with the coarse tailings to produce Blended Composite Tailings, corresponding to the Composite Tailings process in the existing hot water extraction plants.

May 1, 2002

By W. A. Bain

"AbstractProduction from the Excelsior Reservoir has amounted to approximately one million barrels. This production has caused a 'Pressure •drop of 10 p.s.i. from the original pressure of 1,245 p.s.i.g. Volumetric balance calculations indicate that the pool as being produced by a water drive whose strength is •probably unsurpassed in Western Canada. It has also been shown by 'unsteady state' calculations that the reservoir will still be above the saturation pressure of 915 p.s.i.g. at the time of depletion. The average permeability of the producing formation is approximately 1,000 millidarcys and, consequently, well draw-downs are very low. The field is essentially a bottom-water drive and calculations have shown that gravity drainage will greatly assist the recovery of oil. Water flooding data on several cores •have placed the flushing efficiency at •approximately 50 per cent, which indicates a recoverable oil-in-place of 17.7 million stock tank barrels. Calculations and field data indicate that the MER for the early life of this field is probably as high as 8,000 to 10,000 stock tank barrels per day.IntroductionTHE EXCELSIOR NISKU oil reservoir is located about twenty miles northeast of Edmonton. The field was discovered in November, 1949, by Imperial Excelsior N.o.1 well, in Lsd. 13, Sec. 3, Twp. 56, R. 22, W. 4, at a depth of 3,850 feet.Since discovery, development has continued on a 40~acre spacing pattern. At the end of 1951, drilling over approximately 80 per cent of the estimated productive area of 1,680 acres had established 32 we1ls capable •of production. The field •has been fairly well delineated by dry holes on all but the eastern flank ."

Jan 1, 1952

By W. H. Stheeman

"The high rock pressures at the deeper levels of the Tsumeb Mine have necessitated the changing of the mining methods and the introduction of cable bolts. After two rockfalls in the cable-bolted stopes, the mechanics of cable bolting were investigated. Practical methods were developed to find the best grout mixtures, the bond stresses between cables and cement, the bond stresses between rock and cement and the load on the cable bolts, which was mathematically calculated from data observed underground. The design of the cable bolt support system as used at the Tsumeb Mine is explained. GeneralThe Tsumeb Mine is in northern South West Africa/Namibia, approximately 400 km by road from the capital city, Windhoek, at an elevation of 1300 m above sea level. Mining operations in Tsumeb were started in 1905 by the Otavi Minen und Eisenbahn Gesellschaft and continued, with an interruption during the Depre ssion, until 1940, when the mine was closed and taken over by the Custodian of Enemy Property. The present owner, Tsumeb Corporation Limited, obtained the mine in 1947 and restarted the underground mining operations in 1949 after the mine was dewatered. Currently, the stoping operations are between 26 Level (840 m below surface) and 38 Level (1260 m below surface). In addition, the mine is an important silver producer and has produced 670,100 kg of silver since 1947."

Jan 1, 1982

By B. G. Cousins, L. Racine, R. S. MacPhail

"FLEX 31 is a chemically enhanced sodium isopropyl xanthate that has shown improved collection properties over SIPX for copper-bearing and copper-activated minerals. Characteristics such as improvement of recoveries with lower dosages and high pyrite and pyrrhotite rejection capabilities have all been exhibited by FLEX 31.The most improved results have been seen insphalerite flotation. Plant trial work carried out in the zinc circuit at the Louvicourt Concentratorin northern Quebec has produced data showing superior grade and recoveries from rougher concentrates that previously had not been attain-able with other reagents effectively. The improvement over SIPX adds up to an almost$1,000,000 annual improvement on the mine’s bottom line at present zinc prices.IntroductionSodium Isopropyl Xanthate (SIPX) is one of the most popular flotation chemicals on the market today. Somewhat more specific than amyl xanthates, SIPX is used in a variety of ores like copper/zinc, lead/zinc, arsenopyrite/pyrite, and many others (Melis et al., 1991). An investigation carried out by Tennants Research Technology Applications (TRTA), a division of Charles Tennant & Co. (Canada) Ltd., produced a chemically enhanced SIPX that has shown all the advantages of normal SIPX along with improved recoveries of copper and copper activated minerals. The new product has been named FLEX 31. Currently, FLEX 31 is manufactured at the Prospec Chemicals, another division of Charles Tennant & Co. (Canada) Ltd.A large amount of laboratory testing pro-grams have been carried out with FLEX 31 todate (MacPhail and Cousins, 1995; Cousins and MacPhail, 1996). One of the minerals that has a defnite affinity to improved fotation is sphalerite (ZnS). Once activated with copper sulphate, sphalerite has produced some of the most spectacular test work when FLEX 31 is compared directly to SIPX. Plant trials of FLEX31 at Aur Louvicourt Inc. carried out in 1995show that FLEX 31 is far superior to SIPX for activated sphalerite flotation."

Jan 1, 1997

By J. C. Loretto, H. A. Simons

The paper discusses how, in the routine testing of ores, insufficient communication between the laboratory and the design personnel can lead to misunderstanding or misinterpretation of test results and consequent design errors. A number of examples are given together with suggested modified interpretations and the resulting dollar savings indicated by these new interpretations.

Jan 1, 1972

By J. W. Matousek

The heat content of the waste slag from a typical smelting operation methods for estimating the thermodynamic properties of smelting slags, to include: -- heats of formation -- heat capacities (specific heats) -- heat contents -- melting temperatures -- heats of fusion The techniques are illustrated with the analyses of a nickel reverberatory furnace slag from Copper Cliff, an iron-making blast furnace slag, and a "lateritic" slag from a ferronickel operation in Colombia.

Jan 1, 2007

By R. V. Kumar, C. Schwandt, S. Subramanian, S. Sampath, S. Vimalnath

Waste waters and industrial effluents containing toxic heavy metals such as Pb, Hg, As and Cr, beyond permissible limits (0.1 ppm, 0.01 ppm, 0.02 ppm and 0.05 ppm, respectively) (WHO, 2011), pose serious threats to the ecosystem, when discharged into the environment. It thus becomes imperative to monitor the concentration of the toxic heavy metals and treat them before discharging. In this study with the above objective in mind, a microbial sensor has been developed using P. aeruginosa cells drop coated onto a carbon paste electrode (CPE) for the detection of Pb(II) ions in aqueous solutions. Detailed biosorption experiments confirmed that complete bioremoval of lead could be achieved using P. aeruginosa cells under optimum conditions of pH and biomass loading. For the electro-analytical determination, the Pb(II) ions were initially preconcentrated on the P. aeruginosa modified CPE, reduced and then anodically detected with oxidation of Pb0 using differential pulse anodic stripping voltammetry (DPASV) technique. All the experiments were carried out in the presence of 0.1 M sodium acetate buffer and KNO3 as background electrolyte. The parameters namely pH, scan rate, biomass loading, deposition potential, deposition time and concentration of Pb(II) ions were optimized for the biomass modified CPE, to obtain maximum voltammetric response. Under the optimized conditions of pH 5.6, scan rate of 0.008 V/s, biomass content of 1.7–1.8×109 cells/mL, deposition potential of –1.2 V, and deposition time of 500 s, the developed microbial sensor showed a linear response for the peak current between 0.5×10-5 M and 1×10-8 M of Pb(II) ions with the R2 value of 0.9979. The lowest limit of detection (LLOD) was determined as 2.4×10-7M of Pb(II) ions (0.05 ppm). The redox mechanisms of Pb(II) ions on the P. aeruginosa modified CPE surface are discussed.

Jan 1, 2016

By N. R. Thornton

This paper discusses the rapid growth in the application of instrumentation for metallurgical process control. It covers such methods as ultrasonics, pulp density measurements, on-stream X-ray analysis and reagent control, as well as the expanding use of computer control and data acquisition.

Jan 1, 1971

By G. F. Warning

"THE H. B. Mine is situated on the north side of Sheep Creek valley, about six miles southeast of Salmo, B.C. It is the most northerly producer along a belt containing a number of zinc-lead deposits, including the Jersey mine of Canadian Exploration Limited, 3 miles to the south, and the Reeves MacDonald mine, 12 miles to the southwest. The important zinc-lead producing area around Metaline Falls, Washington, lies 23 miles to the south. Two prospectors, Horton and Benson, located and staked the oxidized outcrops in 1.907. The property was named the H.B. after the two discoverers. Exploration by a number of operators failed to locate any sulphide orebodies until 1946, when Cominco began a geological study followed by surface drilling which was successful in locating extensive sulphide mineralization. A program of underground exploration revealed sufficient ore to war-rant mill construction. A 1 ,000-ton mill was completed by 1953, but due to low metal prices production was deferred until May, 1955. To September 1, 1959, 1,900,000 tons of zinc-lead ore have been milled; present milling rate is about 1,250 tons per day. Concentrates are trucked to the Trail Smelter, a distance of 35 miles."

Jan 1, 1960

By Delio J-J Tortosa, Fred F. Langford

"The Cenex orebody occurs at the intersection of northwest and northeast-trending fault zones that formed during post-Hudsonian uplift. The ore is localized in breccia zones, along faults, and in veins and adjacent wallrocks. The host rocks are Tazin quartzo-fe/dspathic mylonites and ultramylonites and chloritesericite- quartz-graphite-feldspar mylonite schist. The uraniumbearing minerals are finely disseminated pitchblende and uraniferous titanate.The earliest mineralization may have been associated with /ate-stage retrograde metamorphism in the mylonite schist. The main stages of mineralization were associated with brecciation, hematization, carbonatization, and chloritization of the mylonites and ultramylonites. Uranium mineralization was clearly much later than any igneous or metamorphic activity associated with the Hudsonian orogeny.Late post-orogenic uplift, erosion, and deposition of the Martin continental clastics in fault basins were coeval with uranium mineralization. The deposit is consistent with a meteoric-hydrologic system constituting a source for orebearing fluids, hence the close spatial relationship of the uranium deposits in the Beaverlodge area with the basal unconformity of the Martin Group."

Jan 1, 1986