Search Documents

By M. Gauthier, A. C. Brown

"Monometallic zinc mineralization associated with marbles of the Grenville Supergroup in the Mont-Laurier Basin of Quebec is found to be stratiform and to occur (1) within limited zones of dolomitic marble and (2) more precisely along contacts between these marbles and adjacent metaclastic units. Massive sphalerite with accompanying pyrrhotite and pyrite is the prime exploration target, and commonly gives rise to good geochemical anomalies, but generally weak and ambiguous geophysical responses. Disseminated sphalerite in dolomitic marbles may signal proximity to interesting massive mineralization, although, due to weathering, this broadly disseminated mineralization may not be detected easily on outcrops. It is concluded that the western and possibly the eastern margin of the Mont-Laurier Basin constitute favourable areas for continued exploration.IntroductionThe Grenville Supergroup marbles of Ontario, Quebec and New York State host numerous occurrences of zinc mineralization (Fig. I) , several of which have been periodically mined since the beginning of this century (Fig. 2). The Balmat Edwards district of New York is the giant of this depo sit-type, with the production since 1915 of some 20 million tons of ore grading 10% zinc, and acknowledged current reserves of approximately equal tonnage and grade. At present, there is renewed interest in the potential for similar mineralization throughout the Grenville Supergroup, and this paper outlines some of the geological, geochemical and geophysical guidelines that may be employed in the search for new ore. The geologic guidelines are derived especially from lithologic and stratigraphic features which survived intense, multiphase deformation and metamorphism.Although major portions of the extensive Grenville Supergroup hold potential for zinc mineralization, the present study is confined to a known zone of mineralization in the Mont-Laurier Basin of Quebec. Concurrently, we are compiling information on the regional metallogeny of the basin so that our conclusions can be applied to areas of similar Grenville Supergroup host-rocks elsewhere."

Jan 1, 1980

By Brian McIntrye, Bo Trygg

"The need for grinding mills of ever increasing capacity and greater feed openings has tended toward mill trunnion diameters being beyond the size limits for roller bearings.Hydrodynamic plain bearings need to be wide enough to achieve the necessary bearing pressure in order to obtain an oil film with sufficient carrying capacity at low rotational speeds. This greater width increases edge loading resulting from the deflection of the mill under load.Because of the high surf ace pressure involved, the life of support rollers and girth rings is often inadequate-fatigue leads to flaking on the contact surfaces. Heat treatment of the girth rings also has its problems.The hydrostatic shoe bearing permits unlimited trunnion diameter and a high carrying capacity. The self-aligning shoes compensate automatically for radial deviations and large deformations can be tolerated at the girth ring.The sliding surfaces are completely separated by oil under pressure, enabling negligible starting torque and good damping capacity to be achieved together with low rotational speeds.IntroductionHydrostatic bearings have been known within machine technology since 1865, when the Frenchman Girard received a patent for such a bearing. During the following 75 years, these types of bearings were used sporadically for thrust bearings, primarily in water turbines. The first usable radial bearing was not designed until 1938. Since the 1950s, when hydrostatic bearings started to come into use within the field of machine tools, extensive research and development work has been carried out at various institutions and research centres throughout the world. Many support problems are now solved by means of hydrostatic plain bearings and the primary factor in deciding to use them is their unique characteristics:• ability to carry high loadings• no starting torque• large damping capacity• no wear• large running accuracyThe hydrostatic shoe bearing has been developed specially for use in the heavy machine industry, with the requirements for high loadings and large support diameters which this market demands."

Jan 1, 1982

By James J. Roettger, Robert J. Mitchell

"The results of a series of model stope pours designed to investigate working pressures on bulkheads during hydraulic pouring of classified tailings backfill are reported. Total bulkhead pressures and fill water pressures were monitored under the condition of a fully saturated backfill. Similitude of the model testing is discussed and equations are developed to estimate bulkhead pressures under prototype conditions. The model results show that good base drainage, combined with a bulkhead setback, can reduce the expected bulkhead pressures to values such that timber or concrete block structures should be capable of supporting a saturated backfill. Introduction Bulkheads are used in underground running operations to block drift openings in order that hydraulically placed sand backfill can be contained in stope pours. Whenever possible, the sand fill is designed to have sufficient percolation rate so that excess hydraulic transport water will gravity drain out through the bulk headed drifts. This avoids costly decanting systems. Early bulkhead design assumed that the bulkhead pressure could be as high as 0h = Hy where H is the fill height and ""y is the saturated unit weight of the fill (Thomas et al., 1979)(1). A typical design pressure for a 50 m fill height would be 1250 kPa giving a design force of 12,500 kN on a bulkhead located in a drift of 10m2 in area . Typical bulkheads were 1 m thick heavily reinforced concrete structures formed and poured into a notched drift. Not only were these expensive structures but the associated problems of inside drainage systems and curing time delays increased production costs. As experience with bulkheads for large bulk pours increased and fill pressure measurements became available [see, for examples, Libby et al., 1975(2), Askey et al., 1978(3)] , 'free drainage' timber and concrete block bulkheads were designed. Substantial savings have been realized using these types of bulkheads but greater engineering design and monitoring of backfill pours is necessary to ensure that backfill pressures do not exceed the bulkhead design pressures.The effective and total stress components of fill pressure, the engineering concepts associated with the 'free drainage' design and some detailed design considerations have been discussed by Smith and Mitchell (1982)(4) . It is important to the safe use of these designs, however, that the basic engineering concepts be demonstrated and communicated to those responsible for the day-to-day backfill operations. This paper describes and explains observations from a series of model studies designed to measure bulkhead pressures in a saturated fill."

Jan 1, 1984

By D. F. Hambley

"In designing are passes f or underground mines specific consideration should be given to unimpaired flow of broken rock, the dump point, and typical practices f or overcoming operational difficulties. Design features such as branches, bends, and knuckles should also be considered. This paper pro vides engineering information and various criteria for designing are passes, draw points. feeders, and support systems, together with several illustrative examples.IntroductionOre passes are the primary mean s o f vertical transfer of mined ore to the ore bins and loading pocket from which the o re is hoisted to the surface (Fig. 1) . While the words "" ore"" and ""ore pass"" are used here, such transfer systems ca n be used for any broken rock.The most extensive ore pass systems are found in caving and sublevel stoping mines. Extensive ore pass systems are also found in multilevel mines having steeply dipping orebodies. In more flat-lying orebodies , ore pass systems are sometimes used in conjunction with conveyor systems .Two decades have passed since the principles of the flow of bulk solids were formulated (Jenike, 1961, 1964; Johanson and Colijn, 1964; Kvapil , 1965). However, few published papers are available that discuss the design criteria for ore pass systems. Therefore, the aim of this paper is to provide the information necessary for good o re pass design .Rock Flow in Ore Pass SystemsIf an ore pass system is to fulfill its function, the transfer o f material must occur in an orderly fashion and in such a way that the full size of the opening is employed effectively. Apart from un controlled flow at the drawpoint, or outlet , whose design will be considered later in this paper, two occurrences may impede flow in an ore pass, namely:• Hangups due to interlocking arches.• Hangups due to cohesive arches.Prevention of each of these problems will be discussed in succeeding sections of this paper. A third problem piping, is related to the ratio of the drawpoint size to the o re pass size and will be discussed under drawpoint de sign."

Jan 1, 1987

By S. Dessureault, M. Yildirim

More mining companies are now investing in IT, including updating one of the traditional IT process control tools used in the mining industry: real time in-pit truck allocation control and monitoring systems, or fleet management systems (FMS). These systems have been used to maximize the overall mine production by improving equipment utilization and reducing production costs. Most modern operations monitor the in-pit operations using GPS and wireless communications to produce data. Improvements in bandwidth, sensors, and computing power are causing modern systems to become more complex and generate more data. However, human analysis by simple regression or table generation in spreadsheets of the data is becoming impossible. Data mining solves this data management problem. Data mining finds patterns and relationships in very large data sets. This paper describes the application of modern data mining techniques on truck dispatching systems in a real open pit hard-rock copper mine. The analyses conducted included determining how the trucks performed under particular conditions and allocation systems. The long-term benefits of this work are to identify strengths and improvement opportunities in truck assignment systems and establish the skill sets and IT infrastructure needed in undertaking more complex datadriven technology such as a truck dispatcher trainer.

Jan 1, 2007

By L. M. Nolan

Chemical Mechanical polishing, or CMP, has four components in the polishing interface; namely the polishing pad, the polishing fluid, the abrasives in the fluid, and the surface being polished. Understanding the way that load is transferred between these components is key to understanding and predicting wafer polishing. Numerous models of CMP and the different load sharing arrangements which occur between these four components have been proposed. These include models by Luo and Dornfield (1) and Fu, Chandra and colleagues (2). Other models focus on just one or two loading arrangements, such as `hydroplaning' when all load is transmitted by the liquid in the case of Runnels and Eyman (3). In this work, we consider four possible combinations of load transfer from pad to wafer in CMP. These combinations are listed below in Table 1 and are illustrated schematically in Figure 1. It is important to note the role of scale in this process; the illustrations in Figure 1 are drawn to scale from actual profilometer scans obtained over a length of 5 with particles of 150 nm in diameter. Table 1 - Load Transfer Combinations Load Regime Illustration Wafer - Fluid - Pad Figure la Wafer - Particles/Fluid - Pad Figure lb Wafer - Particles - Pad Figure lc Wafer-Pad Figure ld The interest in load-sharing between the system components is because some configurations are anticipated to achieve higher polishing rates than others. For instance, in hydroplaning, or hydrodynamic lubrication, the lateral force exerted on the polished surface by the particles can be no higher than the fluid shear force developed in the gap between the pad and wafer. This is not expected to generate high rates of material removal from the surface (4). For contact that is largely between the pad and the wafer, such as the regime depicted in Figure ld, the lateral load is transmitted to the wafer by the pad and is hence limited by the pad's low rigidity. This regime is not expected to generate high material removal rates either. The highest levels of material removal are expected from regimes where the mechanical load exerted on the system is transmitted by the particles, in combination with either the fluid or the pad. Under what circumstances does the polishing regime change from one to another? What must occur in order to initiate or terminate contact between the system components? This is an ongoing question in the field of tribology, and has traditionally been viewed in terms of the pressure and velocity applied to the system, the thickness of the fluid film between the two surfaces, and the roughness of those surfaces (4). In this paper, we propose a new mechanism ? that the load on the particles may be sufficient to totally embed them in the polishing pad, at which point they are no longer able to transmit load and polish the wafer surface. This is illustrated schematically in Figure 1(d).

Jan 1, 2010

By G. W. Poling, E. M. Coelho

"Sedimentary phosphate ores make up approximately 87% of the world's known reserves and are generally more difficult to beneficiate than igneous ores. In almost all cases, desliming prior to flotation represents the major source of losses. Laboratory studies of selective desliming of sedimentary ores are presented. Some fundamental studies with pure mineral systems are also discussed. Selective desliming, especially using selective flocculation, gave the best performance. Possible industrial applications of this selective flocculation-flotation procedure are discussed.IntroductionPhosphate ores are a major source of raw materials used in inorganic fertilizers (which supply nitrogen, phosphorus and potassium). Approximately 96% of the total world production of phosphate is utilized in the fertilizer industry. Reserves and production data are available in the literature. Today deposits with grades as low as 4% P2O5 are exploited in a few cases. However, in some northern African deposits, ore grades are still as high as 33 - 35% P2O5. Hout pointed out in 1982 that approximately 200 million tonnes of phosphate ore were upgraded by flotation only.Although there is a large number of phosphate minerals (over 300, only those in the apatite series are important ore minerals in phosphate ores. The most common member in this series is fluorapatite – Ca5(PO4)3F. However, in sedimentary phosphate rocks, many different substituents occur in the apatite lattice. Carbonate-fluorapatite (or francolite) is one of the most common names used to describe sedimentary apatites. It can be represented by the empirical formula:"

Jan 1, 1986

By Margaret Armstrong, Chris Roth

Abstract -Estimating ore reserves for vein type deposits is a two-stage procedure: first, calculate the geometry of the vein system, and second, estimate the grades within this system. The grade estimation can only be consistently performed if the vein geometry - its size, shape and orientation - has been correctly characterized. Getting the size and shape of the different veins right means that the ore tonnages will not be artificially inflated, e.g., by falsely classifying host rock as veins. Similarly, correctly estimating their orientation and location helps mine management decide on the appropriate mining technique, selective or not. When applying geostatistics to estimate the vein geometry all available information needs to be used and not just the standard lithologic indicator of being or not being in a vein.

Jan 1, 1998

By B. McFadzean, I. Achaye, T. Chidzanira, J. Wiese

"Froth stability has an overriding effect on metallurgical recovery and grade for many ore types. Froth recoveries of less than 10% are common for low stability froths such as those in sparsely mineralized ores or in cells at the back end of flotation circuits. It is well known that, aside from chemical factors such as frothers and electrolytes, the mineral particles themselves have the dominant influence on froth stability. The particle properties of size and hydrophobicity are expected to have the greatest effects on froth stability. The aim of this study was to understand the effects of particle size on froth stability and to quantify these relationships.The study compared a synthetic ore of pyrite and quartz, with carefully controlled size ranges and hydrophobicity, with conventionally milled platinum-bearing UG2 ore and the bulk reverse flotation of hematite ore. A novel bench-scale continuous column flotation cell and continuous mechanical hybrid cell with large relative froth volumes, as well as a three-phase froth stability column were used to characterize the froths.It was found that froth stability could be related to the concentrate particle surface area by a Langmuir-type relationship. This is indicative that the mechanism by which particles stabilize the thin films in froths is similar to the mechanism by which surfactants lower surface tension. Different froth stabilities were found for different ores and this was thought to be the result of different particle sizes and distributions, which resulted in different packing densities in the thin films and Plateau borders. Interestingly, there was a clear relationship between the feed particle size and the froth stability even though froth stability was dependent on the concentrate particle surface area. It seems that the feed particle size is a good predictor of the surface area of particles in the concentrate. Concentrate particle size did not show a clear relationship with froth stability since it was already shown that it is both the size and the amount of the particles in the froth that contribute to the stability.INTRODUCTIONThe stability of the froth in froth flotation is important to the recovery and grade of the valuable mineral. Too stable a froth and the grade is reduced; not stable enough and the recovery may be compromised. Platinum-bearing ores with fragile, poorly mineralised froths are known to have froth recoveries that are routinely less than 10% (Crosbie et al, 2009). There are a number of chemical, physical and operating parameters that can affect froth stability, including reagent dosages, air flow rate, pulp density and particle properties. Arguably, the largest contribution to froth stability is from the particles that stabilise (or destabilise) the thin films in froths. Particle size, hydrophobicity and shape all affect froth stability to some extent."

Jan 1, 2016

By W. B. Evans, D. P. Taylor

"ANFO has two major disadvantages as an explosive low density and no water resistance. ANFO can be blended with more dense, water-resistant explosives to form ""Heavy ANFO"". The use of emulsion or slurry explosives as a matrix is an attempt to correct deficiencies on the basic ANFO while maintaining cost effectiveness.This paper will deal with four main topics.1. Product description, general properties, strengths and weaknesses.2. Technology of ""Heavy ANFO"" , the emulsion matrix concept and the range of products.3. Relative performance and economics in various rock types.4: Current status in Canada and worldwide, and the expectations for future use.IntroductionANFO has been in use for roughly three decades and remains the explosive of choice where conditions are suitable. ANFO has not become the universal explosive - despite its undoubted superiority in cost effectiveness - because it has serious flaws as an explosive. The most serious of these flaws are the low density and absence of water resistance in ANFO. Low density implies a low concentration of explosive energy in a borehole. The amount of energy available can be increased by. adding an energetic material, generally aluminum, or by drilling more holes. Both solutions add considerably to the over-all costs. The absence of water resistance in ANFO is inherent and can only be overcome by changing the fundamental nature of the product. The history of research in the explosives industry since the advent of ANFO is mainly the story of the various attempts to overcome one or both of ANFO's shortcomings.Many technologies and products have been developed to compete against ANFO, among them slurries, emulsion s and the so-called Dense ANFOs (ANFO with an extra nitroalkane liquid sensitizer). None of them was cost-competitive with ANFO so their market penetration has been limited to wet holes or specialized applications. The exception to this result is Heavy ANFO. The aim here was to have the best of both worlds, the high density and water resistance of emulsions or slurries plus the low cost of ANFO. The concept is very simple. ANFO is about 50 % air, roughly 30% in the prills and 700,10 between the prills . The air in the prills provides the necessary sensitivity but the air between them is waste volume. If one fills this volume with a high density, waterproof product, the resultant mix will be denser and more water resistant than ANFO and with very little added cost. This basic concept was invented by B. Clay in the 1970s and is covered by Canadian Patent No. 1 115 959. The water resistance and/or density of the mix can be tailored by changing the emulsion level. Because Heavy ANFO is relatively inexpensive while providing good in-hole densities and water resistance, it can compete successfully against all other bulk products. It competes against ANFO and Al / ANFO by allowing pattern expansion and reducing over-all costs while it competes against emulsions and slurries on price."

Jan 1, 1987

By Makarinskym F. M.

"This paper describes mechanical and operating modifications that were and are being made to current on-line flotation cells at Falconbridge Nickel Mines concentrators. Improved metallurgical performance and metal recoveries of some 3·4% over the past ten years are the end result of the modifications made. The paper acknowledges the contribution of operating, technical and maintenance personnel and the Company ""suggestion plan"" program. 1. INTRODUCTIONFalconbrirdge Nickel Mines Limited, incorporated in 1928 is a major product of nickel, copper,coba1t and other metals and minerals. The Canadian Nickel Division operating facilities in the Sudbury Area currently includes seven mines, two concentrators, and a smelter.For many years at all concentrators, improv0mcnts in metal recoveries have been continually under investigation. One area was to improve the flotation cell performance. This paper will deal with mechanical and operating modifications to the cells at the Strathcona and Falconhridge Ni-Cu sulphide concentrators, at the Sudbury Operations.One of the prime means to mineral beneficiation processing has been, and will continue to be, the basic froth flotation cell. The efficient operation of a flotation cell is the key to satisfactory metal selectivity and recovery. The essence of good design is simplicity. Changes to cell design can contribute to a significant improvement in metal recovery.Over the past 10 years, modifications to the flotation cells have contributed to an improvement of some 3-4” in mineral recovery. Providi11g tl1c initiative for improvements include operating, maintenance and technical personnel, as well as the employee suggestions submitted th1·ough the Suggestion Plan Program."

Jan 1, 1982

By S. Afshar, E. Dajoux, C. Allaire

For various reasons, molten salts, mainly chlorides and fluorides, are used in the aluminum industry. In the holding and melting furnaces, these salts may have different roles such as protecting the metal from oxidation, reducing the metal content of the skim or removing inclusions or impurities from the metal bath. However, the use of these salts may also have some undesirable effects such as easy attack of the furnace lining refractory materials by molten aluminum. The aim of the present investigation was to clarify and to compare the effects of chloride versus fluoride salts, on the corrosion process of the aluminosilicate based refractory materials. A laboratory test and procedure, simulating the conditions at the metal line in the aluminum treatment furnaces, was used. Different aluminum alloys (A1-5wt.%Mg, A1-5.5wt.%Zn and 7075 alloy) and chloride or fluoride salts (MgC12, KC1, CaCl2, NaC1, MgF2, CaF2, NaF and cryolite) were used as well as several aluminosilicate materials. Thermogravimetric measurements were also carried out in order to analyze the effect of the salts on the oxidation of molten aluminum alloys. The experimental results showed that fluoride salts are more aggressive than chlorides against the tested refractory products. It is postulated that the fluorides prevent the formation of a protective oxide layer on the metal surface, favoring at the same time the corrosion of refractories. Moreover, it was found that the presence of Na in fluoride salts increases significantly the aggressiveness of the aluminum alloy towards the refractory samples.

Jan 1, 2004

Abstract - A method to extract certain types of error variance information from paired data is presented, which constitutes an important tool for the calibration of Gy’s formula for variance predictions in the sampling of broken ores. The research summarized here complements publications by others on geochemical precision. The model and method proposed for treating duplicate data provide a practical means of deriving separate estimates of the purely analytical and aliquot sampling variances, from a unique set of duplicate assays, and, hence, proposes a new avenue for estimating effective mineral grain size.

Jan 1, 1998

By J. C. Botham, T. D. Brown

"Coke is the most costly item in steelmaking via blast furnaces . Recent innovations in cokemaking have been directed toward reducing this cost while simultaneously improving coke quality and expanding the range of coals used in the process. It is also important to meet increasingly stringent environmental legislation.Improvements in coke quality have been achieved by novel blend selection procedures, by charge density control using both selective pulverization and partial briquetting, and by the use of modifying additives.The Canadian Carbonization Research Association provides a focus for Canadian cokemakin g research which has demonstrated these technologies in a series of pilot-scale experiments."

Jan 1, 1980

By D. Madsen, B. Salamondra, A. Moss, D. Etienne

"Raise mining at the Namew Lake Nickel Mine in Manitoba uses 3 m diameter bored raises driven at 45 to 50 degrees dip for stope access and drilling. These raises are developed within the orebody on 20 m centres to accommodate electric-hydraulic longhole jumbos and charging wagons. Critical elements of stope development include delineation of are contacts, control of deviation during raise development, optimal stope sequencing to permit a high extraction rate, drill anchorage installation, production drilling and blasting, and ground control. Procedures to deal with these elements are described, with emphasis on the geotechnical investigation for design of open stopes and pillars.Although mining with drilled raises does not have the flexibility to follow large variations in orebody dip, results to date indicate that it can be used successfully in the thicker ore zones. Thinner zones are currently mined using a modified Avoca method. Some flexibility to accommodate variations in orebody dip in thin are zones may be obtained by using alimack raise climbers to drive access raises, and carry longhole drills and charging equipment. Rock quality has been sufficiently good to maintain stable stope walls for full-height mining of primary stapes at 20 m strike length.IntroductionThe Namew nickel deposit is located 60 km south of Flin Flon, Manitoba. It is a moderately dipping (45 to 50 degrees) pipe-like ultramafic intrusion with a sulphide halo enrichment. The diluted recoverable ore reserves at January I, 1990 are 2.2 million tonnes grading 2.05% Ni and 0.7% Cu. The operation is a joint venture between Hudson Bay Mining and Smelting (60%) and Outokornpu Mines Ltd. of Toronto (40%). The mine is budgeted to produce 530 000 tonnes in 1990. The deposit was discovered in 1984 and mine development commenced in 1987.In the raise mining area, primary stopes will be filled with a high quality backfill consisting of cement and quarried limestone. Secondary stopes will be mined out between the primaries in the second pass of mining. The design extraction rate is 94% over all.The orebody above 120 level has an average mining width of 2.4 m, so is too narrow for raise mining. A modified form of Avoca stoping is used."

Jan 1, 1991

By R. H. Seraphim

"The Phoenix Camp, in the Boundary Creek district of southern British Columbia, produced before 1920 about 15 million tons of ore averaging more than l ·5 per cent copper, about 0.03 ounces per ton in gold, and 0·5 ounces per ton in silver. Attwood Copper Mines Ltd. conducted an exploration program in the Phoenix area from 1951to1953.Publications on the camp are listed in the bibliography. Brock's work was not sufficiently detailed to unravel the structural and stratigraphic pro bl.ems. The work of LeRoy and McNaughton is referred to later.The stratigraphic column is as follows:Tertiary.Midway Formation: Volcanics and hypabyssals; dacitic to basaltic flows, with associated dykes and sills of syenite (pulaskite in part) and augite porphyry.Jura-Cretaceous.Intrusives of quartz diorite and diorite (nearest outcrop two miles from Phoenix).Late Palaeozoic or Triassic (Attwood Series).Brooklyn Formation: Sharps tone conglomerate, limestone, grey-wacke and/ or andesitic tuff, with minor shale and basalt. Rawhide Formation: shale with minor conglomerate.Early Palaeozoic.Knob Hill Formation: Chert and andesite, with minor limestone, shale, and serpentine.This column differs from that of LeRoy in two important respects: (I) Attwood's work indicates that the Rawhide shale is basal to, rather than stratigraphically above, the Brooklyn formation. The shale contains conglomerate lenses, which become more abundant and thicker toward the top, and grades upward into Brooklyn conglomerate. Ripple marks indicate that the shale is right side up."

Jan 1, 1949

By A. F. Matheson

"The Jellicoe is the most westerly mine in the Little Long Lac area with a record of gold production. The property is largely covered with overburden and the ore deposit was found by diamond drilling along the projected strike of a gold bearing zone at Magnet lake 1 ½ miles to the east on the property of Bankfield Consolidated Mines, Limited. In 1940-41 Jellicoe mined the whole orebody of approximately 14,000 tons, recovering 5,620 ounces of gold.The vein is in light-coloured greywacke. A mile-long dyke of fine-grained quartz feldspar porphyry 5 to 10 feet in width lies 100 feet south of the vein. A similar, even longer dyke lies 700 to 800 feet north of the vein. Some narrow diorite dykes are also rather closely associated. The porphyry dykes are gold bearing, but not ore. The vein material is quartz and silicified and brecciated greywacke. Mineralization consists of native gold, pyrite, arsenopyrite, and some sphalerite."

Jan 1, 1954

By O. Guyot, A. Broussaud, M. Revalor, G. Legrand, D. Kok, E. Roux

"The paper describes the advanced grinding control system implemented at Newmont Ahafo gold mine, Ghana in 2009 and 2010. It shows how the different components of the Advanced Process Control (APC) system cooperate for increasing plant performance.The SABC circuit processes hard rock from different pits mixed with a variable proportion of oxides. The control strategy is designed to address specific disturbances, including start/stops of pebble crushers, unavailability of oxides, changes in rock size distribution resulting from segregation in the stockpile, and changes in ore type and hardness.The system consists of an expert system per se with extensive use of fuzzy logic, supplemented by an online dynamic model of the process used as a soft sensor, a VisioRock™ rock size measurement system over SAG mill feed before addition of recycled pebbles, and an AudioMill™ system to analyze the SAG mill sound and detect impacts on liners. All these components are embedded in the same OCS© software platform, which, among other benefits, makes it easy to support the entire system remotely. The paper details the physical constraints and the variables that are manipulated. It describes the control strategy and the contribution of each component of the system. It also describes the project implementation and the performance of the system. In addition to a strong involvement and support of management, the very good acceptance of the operators has been facilitated by the remote access system that made it possible to immediately modify the system each time it was needed during the baby sitting phase.The system made it possible to increase gold production significantly through increases in tonnage and recovery thanks to a better control of the grind size through a stabilization of the secondary ball milling circuit and an improvement of the operating conditions of the classifying cyclones."

Jan 1, 2012

By E. Landry, W. Naudts

"The amenability theory was developed by Alex Naudts and considers grouting operations as continuous permeability tests where Newtonian test fluid water, is replaced by a cementitious or solution grout. It utilizes hydraulic conductivity and grouting data to establish the amenability coefficient of a particular grout zone. The amenability coefficient reflects the quantity of apertures or voids accessible to the selected grout, divided by the number of apertures accessible to water, in the zone intersected by the grout hole. By calculating, in real time, the effectiveness of a particular grout at the start of a grouting operation, the most appropriate grout to match design criteria can be targeted. By incorporating the amenability theory in every grouting operation, schedule savings and an increase in productivity are typically achieved. Three short case studies illustrate different enhancements in productivity: At an underground mine during the construction of declines, a cement based suspension grouting program was highly ineffective and did not appear to affect the inflow into the mine workings. The amenability theory was utilized to evaluate the grouting program and based on this evaluation, changes to the grouting program were made which allowed the grouting to meet the project’s objectives. On another project, a pre-excavation grouting program implemented during shaft sinking operations utilized the amenability theory to select the most suitable grout for the program. Schedule constraints also influenced the selection of the grout. In the third case history presented, the amenability theory was used to select the grouting sequence of every individual grout hole for a grouting project in a highly heterogeneous soil formation. INTRODUCTION The amenability of a given soil, civil structure or rock formation for a particular grout formulation is a measure of the ability of that grout to permeate the pores, fissures and apertures water will flow through. The amenability coefficient of a particular grout for a specific zone equals the percentage of apertures, pores and fissures accessible by water that are also accessible by grout. Grouting should be viewed as a continuous permeability test, where the apparent in-situ hydraulic conductivity value for a particular grout zone is continuously evaluated, using grout instead of water as test fluid."

Jan 1, 2019

By Somchet Vongpaisal

This paper presents the R&D results on the development of a new knowledge-based system for predicting stope instability and associated unplanned dilution in deep underground mining operations. A new prototype was developed based on databases generated from 3D non-linear elasto-plastic finite element stress analysis, heuristic rules, and case histories. This prototype aims to assist mine operators to make decisions on strategic mine planning and feasibility in a quick and efficient manner thereby minimizing risk on ground failure and optimizing mining costs.

Jun 1, 2012