Search Documents

By Q. B. Li, B. Gonçalves da Silva, J. T. Germaine, H. H. Einstein, Z. Moradian

"Shale gas and oil production has grown rapidly in recent years, and consequently there are increasing demands to understand the mechanical and microseismic properties of shale. Acoustic emission (AE) monitoring provides useful information on the fracture mechanisms of shale rocks, and provides a basis for interpreting field seismic observations. While there have been attempts for microseismic monitoring of conventional hydrocarbon reservoirs, shale presents a large number of issues that require further investigation. For this purpose, experiments were conducted to understand the characteristics of the AE waveforms propagated through Opalinus shale rock in the time and frequency domains. Frequency range, arrival time, first arrival amplitude and other parameters such as counts, duration and energy of the waves generated from artificial and natural sources in the shale specimens were detected and compared with AE characteristics of granite, a brittle rock that has been extensively investigated. The experimental tests showed that there are some important factors that influence the analyses and interpretations of seismic surveys and microseismic monitoring of shale compared to granite. One of these factors is the anisotropic behavior of shale that causes the wave to propagate with different velocities in different directions. Also bedding planes and micro-discontinuities in the shale cause attenuation of the waves. Thus the AE waveforms that arrive at the sensor are a distorted and attenuated versions of the source waveform.INTRODUCTIONMonitoring microseismic activity from hydraulic fracturing of shale provides vital information for mapping injection paths and fluid migration in order to check the effectiveness of the hydraulic fracture stimulation. Analysis of microseismic source locations can be used to identify fracture networks induced or mobilized during the hydraulic fracturing operation (Rotherd and Shapiro, 2003). On the other hand, by monitoring and assessing detected signals from hydraulic fracturing one can evaluate the induced seismic impact of the stimulation operation.While there have been attempts to monitor microseismic events in conventional hydrocarbon reservoirs, shale presents a large number of issues that require further investigation. For this purpose, experiments were conducted on Opalinus shale to understand its acoustic emission (AE) characteristics in the time and frequency domains."

Jan 1, 2015

By Shawn Harvey

HIGHLIGHTS of STAR DIAMOND PROJECT Initial underground bulk sample 4,048 ct / 25,253 tonnes: US$135/carat: 3,050 ct March 2005 $116 million financing: Newmont takes 9.9% SGF Prefeasibility study commenced on Star Merger with Kensington: 42.245% FALC-JV Voting agreement with Cameco in FALC-JV November 2005 $120 million financing: Newmont maintains 9.9% SGF Diamond valuation: 5,950 ct/ 36,529 tonnes: US$135/carat

May 1, 2006

By Glen Robertson, Jeff McLaughlin

"The Clarabelle Mill rock tailings have the potential to generate sulphuric acid through chemical and biological oxidation of sulphide minerals. Current rock tailings assay between 0.80 -1.40 %S, with sulphur occurring principally as coarse pyrrhotite. Acid generation within the tailings area can be substantially reduced by segregating pyrrhotite rich tailings in a submerged storage area and by depositing only low sulphur rock tailings in exposed areas. Laboratory tests confirmed that low sulphur tailings could be produced by flotation at reduced pH with a small xanthate addition. A plant test was conducted to evaluate the production of low sulphur tailings in conjunction with INCO's continuing commitment to environmental protection and progressive decommissioning of the metallurgical site.During the plant evaluation, approximately 5% of the mill rock tailings were reprocessed in a line of 100 tt3 Denver flotation cells. Tailing grades below 0.40% S were easily achieved through operation at pH 6 -7, with xanthate addition (dosages up to 0.02 lb/ton) and 10 -15 minutes of nominal retention time. Froth depths between 1 -3 inches combined with relatively liberal amounts of frother were required to pull the lightly mineralized froth into the concentrate which averaged 11% sulphur and less than 5% mass recovery. In addition, three field lysimeters were each filled with two hundred.ton bulk samples of low sulphur tails (0.35% S), standard rock tailings (0.98% S), and mill total tailings (2.30% S) for long term monitoring. The implications for full scale plant design, tailings area decommissioning, the possibility of increased nickel recovery and preliminary field lysimeter data are discussed."

Jan 1, 1994

By Richard Q. Fox, Joe L. Pinson

This paper provides guidelines jo1• analyzing and selecting electric power demand controlled. Error calculations, load selections and timing criteria are identified as the three key functions which affect the suitability of a demand controller for any particular application. The advantages of simulating the demand control application on a computer are described, and applications of a demand controller to an iron ore concentrator and a copper refinery are shown. Finally, the paper studies the return on investment for a demand controller.

Jan 1, 1976

By Maurice Hall Haycock

ONE result of the higher price of gold has been the exploitation of many low-grade deposits, the successful treatment of which depends upon obtaining high recovery of the contained gold. Modern methods have made it possible to recover gold from many ores formerly regarded as impossible to treat economically, but in order to apply these methods efficiently it has become desirable, and indeed in many cases indispensable, to gain precise information concerning their mineralogical and physical character. The most successful means of doing this is the use of the reflecting microscope. Reflecting microscopes had long been employed by metallurgists for studying polished surfaces of iron and steel when, thirty years ago, Dr. W. Campbell, of Columbia University, advanced the idea of using similar methods for studying opaque minerals (1). The immediate result was the completion of two microscopic studies, the first on Cobalt silver ores (2) and the second on Sudbury nickel ores (3). The idea was surprisingly slow in being adopted, and not until 1911 did it begin to spread through the universities of this continent. From then on, ore microscopy, or 'mineragraphy', made rapid progress, and, during the next fifteen years, research in universities of North America and Europe led to the development of somewhat specialized apparatus and technique. This phase of development, which resulted largely in contributions of a descriptive nature, furnished a mass of data from which the possibility of economic applications was soon recognized. Ore microscopy became an aid to the mining geologist in solving many problems of ore deposition. This soon led to its application in the study of ores and mill products in connection with their treatment. Its usefulness in this latter field has been very marked and has led to its widespread adoption by the mining industry.

Jan 1, 1937

By George Efremidis, Markos Avlonitis, Elias C. Aifantis, Avraam Konstantinidis

"Nowadays, there is an increasing interest for realistic spring-block models capable of addressing precursor phenomena in catastrophic earthquake-induced landslides. By pre-defining the constitutive law between externally applied stress and induced local strain increments, the dynamic behaviour of the rock/soil slope can be studied by means of the distribution of slip events at the interface between the soil and the bedrock. It is shown that by relaxing the assumption of constant of externally applied stress rate and local strain increments, a robust 2D spring-block model can be formulated for studying triggered landslides. A cellular automaton is built in order to examine the dynamic behaviour and the stability of rock/soil slopes during the initiation of a landslide. The type and nature of the failure plane, as well as the triggering mechanism is studied. The different dynamic evolution modes of the slope can be mapped to specific shape parameters of the corresponding distributions of the incremental displacements. The proposed spring-block model can be used in order to understand, predict and minimize the impact of catastrophic landslides triggered by earthquakes.INTRODUCTIONEarthquakes have long been introduced as one of the major cause of landslides. Earthquake induced landslides are of great importance because they can cause considerable damage and life casualties. Existing analyses can provide landslide concentration, i.e. the number of landslide sources per square kilometer of surface area, as well as the distance from the earthquake source, which is related to the strength of shaking, the slope steepness, which is connected to shear stress, and finally the rock type, which is referred to material strength (Keefer, 1984). In spite of their great importance in social and economic life, earthquake-induced landslides are still considered as an open geotechnical problem. The dependence of the number and distribution of landslides on earthquake magnitude and ground shaking intensities is a crucial factor for the description and determination of the phenomenon. The hazardous types of earthquake-induced landslides, the most susceptible geologic materials and the reactivation of landslides originally triggered by nonseismic activity are some important topics for areas affected by landslides. Most of these areas present an irregular and asymmetric shape with respect to epicenters and fault ruptures, and also show a strong correlation with magnitude (Keefer, 1984, 2000). The number of landslides caused by an earthquake generally increases with increasing earthquake magnitude. Keefer (1984) presented a magnitude scale in order to quantify the number of earthquake-induced landslides. Malamud et al. (2004) have proposed an independent landslide-event magnitude scale on the earthquakes, based on the logarithm of the total landslides number associated with an event. The aforementioned studies try to relate the landslide magnitude scale to the visible effects of the triggering mechanisms."

Jan 1, 2015

By William James Kempson

This paper discusses ore handling systems in shafts. These are considered from the loading facility at shaft bottom all the way through to the discharge mechanism in the headframe. These systems will be discussed from the following perspective: i. Intrinsic safety of the systems ii. The efficacy of the systems to perform consistently iii. The maintainability of the systems iv. Overall system cycle times Particular emphasis is placed on the following specific areas: 1. The Shaft Bottom Loading Facilities The various shaft loading systems currently in use are discussed, the selection parameters surrounding these are quantified and the specific selection criteria are outlined. 2. The Various Skip Configurations In this section the various skip configurations in use around the world will be described and the specific design details associated with these will be highlighted. The advantages and disadvantages of these systems will be compared and the overall efficacy of these will be discussed. 3. The effect of the loading and skip configurations on the Load Cycle Times. The overall cycle time which can be achieved by a shaft system is strongly dependant by the speed and efficiency with which the ore can be loaded and transported out of the mine. The potential of the various systems to be optimized will be discussed. The emphasis of this paper is to highlight the lessons which have been learned with respect to ore transport system design and provide a common basis against which these can be compared in future applications.

May 1, 2013

By G. D. Ruttan

"LYNN LAKE, in northern Manitoba, has become Canada's second nickel-producing area. The discovery by Sherritt Gordon Mines of nickel ore in an entirely new district was the result of systematic prospecting of a belt of volcanics and sediments situated 100 to 150 miles north of the Company's former copper-zinc mine at Sherridon, Manitoba.Prospecting in this area was begun in 1937 and continued each year until 1941, when Austin McVeigh, a company prospector, found a patch of sulphides on a gabbro outcrop near a small lake named Lynn Lake. Samples from this sulphide indicated nickel and copper in significant amount. In 1943, magnetometer work disclosed a number of weak anomalies in low ground near the discovery. In 1945, staking was followed by geophysical surveys and diamond drilling, which continued through 1947. During this period the A, B, E, EL, and Corebodies were located and partly outlined. The discovery of the high-grade ""EL"" orebody in January 1947 was the turning point in the estabishment of the mine. Subsequent development, including additional exploration on surface and under-ground, evolution of a new metallurgical process, financing, erection of a mining and milling plant, hydro-electric power development, building of a rail line from Sherridon (by Canadian National Railways) and a refinery at Fort Saskatchewan, Alberta, culminated in August 1954, when the first shipment of nickel left the refinery. This paper, presented at the 1955 Annual General Meeting of the C.l.M. in Toronto, was one of a symposium covering the whole operation."

Jan 1, 1949

By E. Ghali, C. Su, G. Houlachi

"The influence of lead ions on zinc electrowinning process was investigated by means of electrochemical noise measurements (ENMs) and cyclic voltammetry in conjunction with scanning electron microscopy and X-ray diffraction. All electrochemical experiments were performed in sulphuric acid electrolyte containing different lead ion concentrations as impurity. Lead was added in six trace levels between 0.05–0.8 mg/L in the bath. The lead content of the zinc deposits was dependent on the introduced lead concentrations. The overpotential associated with zinc electrodeposition shifted to higher values with the increase of lead concentration in the solution. An appropriate correlation was found between the different concentrations of lead in the electrolyte and the morphology of zinc deposit by ENM. The results showed that the increase of lead ion concentrations is generally accompanied with the decrease of skew and increase of kurtosis values that could be related to the morphology of zinc deposit. Effectively, the morphology changes from well-defined hexagonal platelets to large hexagonal, layered platelets and finally to non-symmetric refined crystalline structure, respectively.INTRODUCTION In commercial zinc electrowinning, zinc oxide is leached from the roasted calcine with an aqueous acid sulfate electrolyte. Then the zinc-rich solution is purified and transferred into an electrolytic cell. During electrolysis, zinc is deposited on aluminum cathode where lead-silver or pure lead is served as anode. Electrodeposition of zinc could be influenced by several parameters such as bath acidity, temperature, current density, the nature and concentration of impurities as well as additives in electrolyte. Metallic impurities play a complex role during zinc electrowinning and they can adversely"

Jan 1, 2016

By J. A. Hillier

"IntroductionThe purpose of sampling is to remove a portion of material from a stream which is representative of it in size, moisture and mineral content.To prevent the effects of segregation, generally caused by the way in which a conveyor, pipe or launder is loaded or directed, the sampler should cut proportionally the entire cross section of the stream.If one conveyor transfers to another at a right angle, fines may be dropped on the near side, and the coarse material thrown to the opposite side. Segregation can also occur as a result of the motion of a conveyor belt passing over the idlers causing the coarse material to roll to the sides of the belt.When slurry changes direction of flow in a launder or pipe, the heavier and coarser fraction will centrifuge to the outside of the curve and tend to remain on one side of the stream. Similarly, if two streams joining in a common launder are not mixed at the point of confluence, they will continue down the launder unmixed . This effect is particularly noticeable in a plastic lined launder.Therefore, a proportional sample is usually accomplished by a constant rate of cutter travel across the entire stream, making certain that the cutter is not full or splashing over before reaching the end of travel.The cutter should operate on a constant interval based on time, tonnage and uniformity of flow. The opening should be at least three times the width of the largest piece to be sampled. The cutter width is more critical with ore samples where particle sizes are large. With slurry samples, the opening is usually much larger than the minimum in order to obtain sufficient samples"

Jan 1, 1989

By A. F. Robertson

FOR several years, the rock-burst question has been given serious consideration by the operating staff at Wright-Hargreaves mine and, as a result of observations and experiences, several different methods of mining have been developed which are now in use in various parts of the mine. These are described in the following pages. It should be emphasized, how-ever, that these methods, and the views expressed in this paper, are based solely on conditions at Wright-Hargreaves mine. Such conditions may or may not be similar to those obtaining in other mines in the Kirkland Lake area, where ore occurrences, veins, wall-rock, faulting, intrusives, etc., may be entirely different. Size and shape of ore-bodies, composition of the ore-bodies and their surrounding rocks, locations of intrusives and sedimentary rocks, and direction, dip, and strength of faults, all introduce problems that are peculiar to each individual mine. Ground failure' in coal and metal mines is not at all unusual. A variety of systems of mining have been developed to delay movement of large or small blocks of ground, or, in some instances, to take advantage of the fact that ground movement, due to mining operations, is unavoidable. Ground failure may be either slow collapse or it may take place with explosive violence. It is principally with the latter condition that we are concerned in the mines of the Kirkland Lake district.

Jan 1, 1939

By C. D. Smith

Numerous studies have shown the potential of air rate profiling to significantly improve the flotation performance of a bank of cells. To date many profiles have been implemented; balanced, increasing, decreasing and combinations of these. Previous work has typically shown using an increasing air rate profile, where the air rates are increased proportionally to each cell down the bank, yields a higher grade for a given recovery compared to other profiles. Air rate profiling can then be thought of as having two distinct components; determining the correct distribution of a given volume of air and, perhaps more importantly determining the correct total volume of air to add to the bank. To date no method for this second component has been established. In an alternative technique the air rate to each cell is adjusted in order to optimise the air recovery from that cell. Air recovery is the fraction of the inlet air which overflows the weir of a cell as unburst bubbles. The peak in air recovery (PAR) is a robust measurement that indicates optimal performance for the operating conditions in the cell, and sets the PAR air rate. By doing this for each cell in the bank, the optimal total air rate to the bank and the optimal distribution of that air can be simultaneously determined. In this study plant trials evaluated different air rate profiles, and profiling based on PAR. The total air rates to the bank for all profiles tested were approximately equal, allowing direct comparison. The results showed that the highest cumulative mineral recovery was achieved by operating at air rates which gave the PAR for each cell down the bank. Different distributions of the same total air rate to the bank gave the same cumulative upgrade ratio, but lower cumulative recoveries. In this study, the increase in cumulative mineral recovery, at the same upgrade ratio, was more than 33%. Peak in air recovery (PAR) based optimisation of air rates to banks of cells and to the individual cells has been shown to significantly improve flotation performance as it simultaneously determines the optimal air rate to the bank, and the optimal distribution of that air.

Jan 1, 2009

By C. E. Baltzer, W. H. Harper

"This study has been developed to illustrate the trend and pattern of distribution applying to the quantities and costs of the fossil fuels used, and the related amounts of electricity generated, in the thermal segment of the Canadian electric utility industry.Traditionally, Canada's requirements for electric energy have been preponderantly met by hydraulic power. The need for augmented supplies of thermally generated power has mainly developed since the close of World War Il-in an era that has seen drastic decline in the production of indigenous coal and buoyant expansion in the supply of oil and natural gas. Although coal currently is faced with serious competition from the fluid fuels, the utility industry in particular promises an advancing market for coal, because of its abundant resource, at prices less likely to show sharp increase. For Canada as a whole, this trend has been progressive since 1959, and, unbelievable as it may now seem, the extent of the advance by 1975, particularly in Ontario and the Prairie Provinces, may well be as much, or even more, than the present rate of consumption for all purposes.The text and the tables and charts are arranged to focus attention on: the growth of thermal genera ting capability; the historical trend in consumption of fuel and the related production of electricity; patterns of distribution by types of fuel and thermal capacity; the relationship of steam to other sources of thermal capacity; and the quantities, costs and related percentages of electricity generated by types and kinds of fuel used, both regionally and provincially."

Jan 1, 1966

By R. Minto, W. G. Davenport

The slag removed from the reverberatory furnaces of copper smelters contains significant copper values. A serious financial loss is involved, as further recovery operations are not normally carried out. This paper describes the factors affecting physical transport of matte into slag by gas bubbles, and the subsequent entrapment and flotation of matte drops. Three distinct patterns of transport behaviour have been identified from studies of a number of liquid/liquid systems, including liquid metal and liquid matte systems. A theoretical approach is proposed to explain these behaviour patterns, and to predict transport and entrapment behaviour in matte/slag systems. The concepts of "Film Coefficient" (ø) and "Flotation Coefficient" (?) are introduced. The effects of smelting process variables on the physical loss of copper matte in slag are also discussed.

Jan 1, 1972

By L. H. Thorleifson

Demand for both gem and industrial diamonds is very strong. Synthetic production supplies industrial uses, but synthetic gems remain inferior and expensive, so the large gem market is supplied by mining. Several major mines have been depleted, and the market is receptive to new sources of high quality gems. Canada's Precambrian terrane, extending across the Canadian Shield and under the Phanerozoic cover of the Plains and Hudson Bay, has excellent potential for diamonds, but exploration conditions are difficult due to recent glaciation. Early world exploration relying on recognition of diamond in alluvial sediments was adequate to launch pre- 1900 production from India, Brazil, and Africa. Exploration success in Canada, as was the case in Russia and other more recently discovered sources, however, had to await large investments in effort supported by advanced science and technology. Canadian exploration in many ways is similar to that in other regions, relying on analysis of tectonics, indicator minerals, geophysical surveys, and multiple stages of drilling and sampling. Very different from other regions, however, is Canada's surficial environment, in which recent glaciation has caused fresh indicator minerals to be transported hundreds of km. Exploration accelerated in Canada after 1960, first in Ontario and the Arctic Islands, then in Saskatchewan in 1988, and most importantly after the Chuck Fipke - Stew Blusson discovery at Lac de Gras, Northwest Territories, in 1991 that led to the billion-dollar BHP - Dia Met Ekati Mine that opened in 1998. In 2003, production from Ekati will be supplemented by that from the similar and nearby Diavik Mine of Rio Tinto and Aber. These mines will bring Canadian output to over 10% of world supply, and will position Canada with Botswana and Russia as world leaders in production of high quality gem diamonds. There could be other mines as well, as sites across the Arctic and in the south from Alberta to Québec are being explored by an array of companies, including De Beers, other majors, and several juniors.

May 1, 2003

By Lauri Gregg

How Can Man Meet the Carbon-Free Energy Challenge ? ? Increases in Energy Efficiency can displace 1/2 to 2/3 of the Carbon-Free Energy required to stabilize at 550 ppmv ? Renewable Energies require too much land and thus can displace 5 to 10 % of the energy requirement ? Large new sources of carbon free energy are needed ? Conservation is desirable but provides only a small and variable contribution ? People will have to adjust to higher levels of CO2 in the atmosphere as energy demand continues to grow

Nov 1, 2002

By E. Fritz

This paper reviews the history, developments and 10 milestones of the oxygen steelmaking processes, with a special focus on conventional autothermic converters, high-speed converters with a blowing rate up to 5 m3n/t min and allothermic converters with coal addition, post combustion and the possibility to increase the scrap rate up to 50%. Related operating results are introduced. A new process route, which is based on hot metal and chromium ore, is outlined. The cost advantage for the production of 304 stainless steel grade is higher than 100 USS/t. The synthesis of EAF and oxygen converter steelmaking, a comparison of decarburization rates, refining combustion burners for optimized oxygen-management in EAF and an example for a large advanced EAF are outlined. Possibilities of flexible steelmaking and the growth and outlook of worldwide oxygen steelmaking are described.

Jan 1, 2004

By T. P. Riordon

"Major swings in the silver price since 1979, along with the ever constant fight to maintain ore reserves has forced United Keno Hill Mines Limited through several unique series of events in order to survive in the 80s.This paper is specifically meant to be a description of safety and productivity improvements achieved to ensure the survival of a silver mining community ill the Yukon. There are, however, other events and conditions that must be described to complete the story and this paper attempts to do that as well IntroductionUnited Keno Hill Mines Limited, a subsidiary of Falconbridge Limited, is the only silver producer in the Yukon. Operations are located in north central Yukon, in and around the small town of Elsa, latitude 62.5 °, about 275 road miles from Whitehorse. The Arctic Circle is about 185 miles due north of the town.Temperatures in 1986 ranged from a high of 28.5°C in July to a low of -37.0°C in November, however, much lower temperatures have been recorded in previous years. Due to the mountainous terrain the town of Elsa is completely in the shade from mid-November until early February, a period of about 12 weeks.The Elsa area, as is most of the north, is considered semiarid with an average precipitation level of about 15 inches. Vegetation, however, is quite abundant though slightly dwarfed at the townsite elevation of 3200 feet above sea level: Many of our operating and exploration portals as well as our open pits are above the tree line. Permafrost in the area has been recorded up to 400 feet below the surface."

Jan 1, 1988

By Roger V. Pierce

"WITHOUT mineral wealth, modern man would not exist. True, man could survive on a stone-age basis with an average life expectancy of, say, 25 to 30 years -once he got past infancy.However, no metal would tip his arrow in a hunt for protein; no steel plough would break the soil for the organized planting of seed; and no coal, nor oil, nor natural gas nor uranium fuels would pro-vide him with light or beat or safety from either beasts, or other men, or an unkind nature that threatened him and his family.Modern agriculture, fishing and forestry represent the other three wealth-producing industries. With-out metals, non-metallics and energy minerals, however, it would be impossible to fit any of these to man's modern needs."

Jan 1, 1967

By C. J. Sullivan

It is of importance, in prospecting, to distinguish ores of magmatic origin from those derived by the meta-morphism and granitization of source rocks and from those accumulated in certain sedimentary facies. The magmatic ores, which are characterized by their occurrence along fault structures, may be associated with volcanic (including explosive) phenomena. Heat effects are local. The magmatic sequence is well de-fined: kimberlite, with diamond pipes; ijolite, with carbonatites; peridotite, with nickel deposits; norite, with nickel-copper deposits; and diabase-gabbro, with copper-zinc deposits. These deposits are characteristic of Precambrian shields, where a thick sialic crust may rest on basic to ultrabasic magma. The sequence is resumed in the Paleozoic terrains (in a broad sense), with monzonite porphyries and associated copper, copper-gold, and cop-per-lead-zinc deposits.

Jan 1, 1962