Search Documents

By Mahmood Alemrajabi, Ake Rasmuson, Kerstin Forsberg, Kivanc Korkmaz

"In the present study, the recovery of rare earth elements (REE) in the nitrophosphate process of fertilizer production is investigated. The apatite has been recovered from iron ore tailings by flotation. After digestion of apatite in concentrated nitric acid, Ca(NO3)2.4H2O is first separated by cooling crystallization and then the REEs are recovered by precipitation. Optimum conditions in these steps have been determined in a previous study. The precipitate mainly consists of CaHPO4.2H2O and REE phosphates.In the present study, selective dissolution and re-precipitation have been studied in order to obtain a precipitate that is more concentrated in REEs. The precipitate was selectively dissolved in nitric and phosphoric acid at different acidities (pH 6 to 0) with the liquid /solid ratio of 100 mL/g. It is shown that most of the CaHPO4.2H2O and other calcium containing compounds will be dissolved at pH 2 while the REE phosphates are not dissolved above a pH of approximately 2. Thus, by partial dissolution of the REE precipitate at pH 2.5 most of the solid calcium phosphates will be dissolved and the remaining solid phase, which is more concentrated in REEs, can be filtered off as a fairly concentrated REE solid mass and the liquor can be recycled back to recover more P nutrients. Alternatively, the REE enriched precipitate was dissolved completely in nitric acid and re-precipitated again by addition of ammonium hydroxide to pH 1.2. A chemical equilibrium software, MEDUSA (Puigdomenech, 2013) has been used to evaluate the experimental results and to estimate the optimum conditions for selectively dissolving the precipitate."

Jan 1, 2016

By Sunil S. Gandhi

"The Mountain Lake deposit is a tabular sandstone-type uranium deposit, hosted by the basal unit of Middle Proterozoic Dismal Lakes Group. Uranium occurs mainly as sooty pitchblende disseminated in stratiform lenses within gently dipping quartzose sandstone. It is associated with copper sulphides, pyrite, hematite, and traces of nickel and cobalt arsenides and of silver.Exploration HistoryUranium showings on the PEC claim group were discovered during 1969 by an airborne radiometric survey carried out over the Dismal Lakes-Great Bear Lake area by Aquitaine of Canada Limited (Bizard and Salat, 1969). Some drilling was done in the vicinity of the showings in 1975 by the company under a joint venture with Eldorado Nuclear Limited but the results were not encouraging (Hassard and Woollett, 1975). During 1972, Trigg, Woollett and Associates Limited conducting surveys for Imperial Oil Limited, discovered numerous high-grade radioactive boulders scattered over a distance of several kilometres north and west of the showings, and the area north of the PEC claims was staked as the YUK claims (Ahuja, 1974). A systematic study of the boulder distribution and Pleistocene geology suggested a source additional to the showings. More intensive exploration followed, and in 1976 drilling just north of the PEC claim group boundary intersected the main deposit at a depth of 75 m to 150 m, beneath overburden up to 60 m thick. Part of the deposit extends into the PEC claim group which is under exploration by the Aquitaine-Cominco Joint Venture.The following brief description is based on the presentations in 1978 by F. Hassard of Trigg, Woollett and Associates Limited at the Geoscience Forum in Yellowknife, and by S.S. Gandhi of the Geological Survey of Canada at the Mineralogical Association of Canada Uranium Short Course in Toronto."

Jan 1, 1986

By Z. D. Hora

Traditionally, industrial minerals in British Columbia comprise about 10 per cent of the combined value of mineral, coal, petroleum and natural gas production. Over the years a wide variety of industrial minerals have been produced in British Columbia, often with a different level of marketing success. For some products such as building stone, common brick or expanded shale, once strong demand gradually disappeared; for others such as asbestos and barite, new discoveries or new industrial activities created demand and new markets. For yet other minerals such as fluorite, talc and perlite, wider use has been prevented by the small size, poor quality or remote locations of the deposits. Bentonite (1926 to 1944-as a by-product from coal mines) Building stone (intermittently since the mid-1800s) Chromite (1918 and 1929) Over the past years, the list of industrial minerals produced has been expanded to include several new commodities: glassgrade silica sand, magnesite, pumice and silica for ferrosilicon and silicon carbide manufacture.

Jan 1, 1984

By S. L. Gula

"Effective and timely communication during routine operations, and especially during emergency situations, is no easy task in any underground mine. At Cominco Fertilizers, Potash Operations, where 150people are employed underground to produce 3.1 million tonnes of potash per annum at a depth of 1100 m (3600ft), this is no exception. The over-all mine workings underlie an area of approximately 20 km 2 with average travel time to the active mining areas being approximately 30 to 40 minutes by light vehicle, and significantly longer than this for heavy equipment.In a mine of this size, the deployment and management of personnel and materials on a day-to-day basis, and during mine emergencies, is an important exercise. The Personal Emergency Device (PED) system has provided the Potash Division a means to achieve improvements in this area and reduce the communications bottleneck.The MineAt Cominco Fertilizers Potash Operations, approximately 30 km southwest of Saskatoon, the orebody is the same horizon being mined by other potash producers in the Saskatoon area and extends over 300 km in an east-west direction, and approximately 150 km in a north-south direction. Mining operations are carried out with approximately 150 employees operating on a continuous-shift basis, seven days a week.Mining is presently being done from Block 6 which takes the mine to its northernmost boundary and contains reserves of approximately 50 million tonnes. Production is from one level by five twin rotor continuous mining machines, each capable of cutting a face up to 5.5 m wide and 3.3 m high . All ore is transported to the shaft via approximately 20 km of conveyor where it is removed to surface by two 24 tonne skips.After the ore is conveyed to the mill for processing, the finished product is shipped by rail car or trucks to other parts of Canada, the United States or through Vancouver to other parts of the world."

Jan 1, 1993

By L. E. Gutiérrez

A new filtration model based on porous media transport theory is presented. It predicts capacity and final moisture content in the filtered cake as a function of design and operational variables at the plant. FilterSim® is the computer code where this new model is programmed. Application of FilterSim® to ten-month operation of an industrial copper concentrate filtration plant is shown on a daily basis and using a single set of internal parameters for the whole period. Average error is less than 5%, both in capacity and moisture estimation. FilterSim® abilities to optimize industrial filtration plants as well as to estimate future budgets are illustrated with several real examples.

Jan 1, 2007

By A. J. Rigby

Computer generated, actual-scale furnace models have been imported into a rendering software application to provide for impressively realistic surface features and lighting. When these models are imported into a 3D engine framework, it is possible to create content-rich virtual environments allowing for complete interactivity and could provide for a powerful tool to conceptualize refractory lining designs. This technology has been applied to illustrate the optimized design concept of an anode-refining vessel, which can be expected to be completely relined in six days and to last for 4-5 years with minimal partial relining. This technology could easily be applied to other smelter furnace, converter and refining vessel designs.

Jan 1, 2007

By W. B. Xie

The hardening behaviour and microstructure evolution of Cu-30Ni-30Mn alloys aged at 350 °C has been investigated utilizing optical microscope, scanning electron microscope, transmission electron microscopy and Vickers hardness tester. The results show that the discontinuous precipitation of NiMn phase results in a remarkably hardening effect in Cu-30Ni-30Mn alloy during aging at 350 °C. The maximum hardness (~494HV) is attained in the sample after aged for 48 h. The NiMn precipitates are ordered and have a face-centered tetragonal structure. The coherent orientation relationship between the NiMn precipitates and Cu matrix is (220)Matrix // (220)P, [1-1-2]Matrix // [1-1-2]P. In addition, there is a linear relationship between hardness and volume fraction of the discontinuous precipitation, which indicates that the hardness increment of Cu-Ni-Mn alloys aged at 350 °C is attributed to the microstructure characteristics of discontinuous precipitation. The high strength of discontinuous precipitation colony is caused by the formation of nanoscale NiMn precipitates with a lamellar structure in discontinuous precipitation. INTRODUCTION Cu-Ni-Mn alloys are attractive candidates for oil drilling, aerospace and energy applications due to their high elasticity, high strength and excellent corrosion resistance (Sun et al., 2009; Liu, Yang, Xia, Jiang, & Gui, 2016). The high strength of the Cu-Ni-Mn alloys is mainly attributed to the precipitation of NiMn phase (Shapiro, Tyler, & Lanam, 1974; Xie et al., 2015). The uniformly dispersed nanoprecipitates formed by continuous precipitation can impede dislocation movement, and thereby lead to a significant improvement in strength of traditional precipitation-strengthened alloys. However, it is reported that there are two precipitation types observed in Cu-Ni-Mn alloys, namely, continuous precipitation and discontinuous precipitation (Shapiro et al., 1974). The discontinuous cellular colony with a lamellar structure nucleates at grain boundaries, and progressively grows inward the grain on the process of discontinuous precipitation (Ng, Bettles, & Muddle, 2011). It is found that the discontinuous precipitation can occur in many Cu-based alloys, such as Cu-Ni- Mn alloy (Shapiro et al., 1974), Cu-Be alloy (Monzen, Hasegawa, & Watanabe, 2010) and Cu-Ni-Sn alloy (Zhao, & Notis, 1998). Many studies consider that the discontinuous precipitation results in a detrimental effect on hardness and strength, and the discontinuous precipitation occurring during aging treatment should be suppressed (Markandeya, Nagarjuna, & Sarma, 2004; Semboshi, Sato, Iwase, & Takasugi, 2016). The mechanical properties can also be improved by discontinuous precipitation in AZ91 magnesium alloy (Tamura, Kida, Suzuki, & Soda, 2009) and AM30 magnesium alloy (Saikawa et al., 2012). Jun (2017) found that the reduced interlamellar spacing of precipitate fibers in discontinuous cellular colony leads to a significant increase in hardness. Indeed, the strengthening contribution of discontinuous precipitation is similar to that of continuous precipitation in Cu-20Ni-20Mn alloy. Discontinuous precipitation of NiMn phase can provide a significant strengthening effect in Cu-Ni-Mn alloys.

Jan 1, 2019

By K. Sawamukai, S. Ogasawara, D. Umenai, T. Tsuruta

"Removal of cobalt, strontium or cesium ion from the aqueous solution containing each metal ion only using microorganism was examined. Arthrobacter nicotianae which had a high ability to remove cationic metal ion was used for the removal of each metal. The removal of cobalt, strontium or cesium using A. nicotianae cells was affected by the solution pH, concentration of metal ion, and cell amount. The effects of above mentioned factors on the removal of each metal and time course of strontium from the solution containing each metal only using A. nicotianae cells were reported in this paper. INTRODUCTIONRadioactive elements, such as cesium, iodine, strontium, plutonium, barium, cobalt, lanthanum, yttrium, and tellurium, were detected around Fukushima Daiichi nuclear power plant, which was damaged by the magnitude 9.0 earthquake and the tsunami followed.The removal of radioactive elements from contaminated sources is a worthwhile subject to investigatein terms of environmental control. Research efforts have been especially concentrated on studying microorganisms that remove uranium including bacteria (Andres et al, 1993, Hu et al, 1996, Marques et al, 1991, Strandberg et al, 1981), actinomycetes (Byerley et al, 1987, Friiss and Myers-Keith, 1986, Golab et al, 1991), fungi (Byerley et al, 1987, Galun et al, 1983a, Galun et al, 1983b,Tsezos and Volesky, 1981, White and Gadds, 1990) and yeasts (Strandberg et al, 1981, Schmate II et al, 1978).We have investigated removal and recovery of uranium from aqueous systems using microorganisms isolated from uranium mines. We identified some strains of bacteria with extremely high uranium removing abilities (Sakaguchi et al, 1996), and thus, the microbial biomass may be considered as an adsorbing agent for the removal and recovery of uranium and heavy metals present in aqueous systems around Fukushima Daiichi nuclear power plant.In the present study, we screened various species and strains of bacteria, actinomycetes, fungi, and yeasts for their ability to adsorb uranium (Tsuruta, 2002). Basic features affecting uranium adsorption?co-existing cations and anions, cell amounts, pH, and the adsorption time course?by Arthrobacter nicotianae cells, which adsorbed the largest amount of uranium, were also investigated. In addition, we examined the removal of an other actinoid element, thorium ion, which may be present with uranium in refining effluents.In this paper, the removal of cobalt, strontium, or cesium from the solution containing each metal ion using A. nicotianae cells is discussed."

Jan 1, 2012

By R. von Bonsdorff

Electrochemical and quartz crystal microbalance (QCM) methods were used to investigate the dissolution rate of gold in a solution similar to those utilized by the Outokumpu HydroCopper® process. The measurements were conducted in an electrolyte solution where [NaCl] = 2.8-280 g/L, pH = 1-2.5, [Cu2+] = 0-30 g/L and T = 70-95°C. According to these measurements, the solution flow has the greatest impact on the dissolution rate of gold in the HydroCopper® process. Under adequately acidic conditions (pH < 3), the dissolution rate of gold increases with increasing cupric concentration, increasing chloride concentration and increasing temperature. The results and trends observed compared well with the literature.

Jan 1, 2007

By Ronald C. Schimmel

In 2006, the Corus IJmuiden pellet plant produced approximately 4.6 mln tonnes of pellets. Corus IJmuiden is about to increase its pig iron production to 6.4 mln tonne HM per annum. The burden of the Corus IJmuiden blast furnaces consists of approximately 50% high basicity sinter and 50% acid pellets, both produced in-house. To enable an increased iron production, the capacity of the pellet plant needs to be raised to 5.0 mln tonne per annum. The capacity is increased by modifications to the plant layout, which were implemented during the 2006 cold maintenance stop. In addition, the composition of the ore blends is optimised to gain productivity.

May 1, 2007

By P. Wanjara, M. Xiao

During fusion welding of aluminium alloys, the avoidance of defects (such as porosity, oxides, hot cracking, undercutting) as well as the ability to optimize the microstructure-property characteristics in the assembly are critical for the stringent manufacturing specifications in the aerospace industry. In this work, aluminium alloy (AA) 2024 was electron beam welded autogenously as part of a study to determine the influence of parametric conditions on the characteristics of the heat affected and fusion zones to obtain optimal welding conditions. In particular the evolution in the weld geometry, microstructure and mechanical properties were examined as function of the processing conditions, including beam current, beam focus, beam oscillation, linear heat input and welding speed. For optimized parametric conditions, microstructural examination of the joints revealed narrow fusion and heat-affected zones comprising of dendritic structures without the occurrence of defects that enabled a maximized joint efficiency.

Jan 1, 2006

By Bernard Tougas, Franco Chiesa, David Levasseur, Bernard Duchesne

"In the present paper, the optimization of a tilt poured permanent mold will be carried out using filling and solidification modeling. This exercise resulted in 3 modifications of the initial mold design which was based on the foundry experience. The optimization provided a 20% improvement in the yield while increasing the output from 10 to 15 castings per hour.In a subsequent study, the value of the critical fraction solid of AlSi7Mg (A356) alloy was verified by radiographic analysis of the castings produced in the first 5 cycles of a run, which are necessary to bring the mold to a dynamic thermal equilibrium."

Jan 1, 2014

By R. Burnette

Gold has been mined from a variety of deposit types that range in age from Archaean to Recent. The large variability in the geological settings of the gold deposits implies transport and concentration of gold by magnetic, hydrothermal and sedimentary processes. The factors that control the concentration of gold at certain sites and the grade estimation thereof remain major topics of debate. Due to the complex nature of the Witwatersrand Basin a mineralogical study, including mineralogical, petrographic and geochemical investigation was launched on TauTona Mine in order to characterize the various reef facies. The aim of the investigation was to determine if a correlation could be found between macroscopic characteristics of the reef, hanging wall and footwall, and the microscopic nature of the ore (especially gold grade). Petrograpgic and mineralogical results indicate that a correlation exist between gold, detrital and hydrothermal sulphides, uraninite, carbon, detrital heavyminerals and phyllosilicates. No correlation exist between gold and Mg, Fe or S. It appears that clast supported reef is of higher wade than matrix supported, but more work is suggested. No correlation exists between reef thickness and grade. The reef samples had the lowest phyllosilicate content compared to the hanging wall and footwall samples with pyrophyllite the most dominant. All of the correlations diagrams showed significant scatter and suggests a multi- factorial mineralization model. Gold distribution is also controlled by sedimentary features and thus it is not possible to select a single model for the formation and distribution of gold. It is evident that both sedimentary and hydrothermal factors influenced the mineralization and gold distribution on TauTona mine. It is thus essential that all related theories be incorporated in the development of a grade prediction model.

Jan 1, 2011

By S. Srinivasan, R. Coté

"India is undergoing a massive electrification program using local coal to provide fuel for thermal generating plants. The Rajmahal mine in northern Bihar is scheduled to produce coal at the rate of 10 million tonnes per year by the end ofa sixty six month contract with MET-CHEM Canada Inc. for mine development. In order to control maintenance performance and warehouse inventory MET-CHEM is installing some proven computer-controlled programs and will provide extensive training to ensure that the systems are properly used. The programs are Maintenance Planning and Control System (MPCS) and Materials Management System (MMS), both of which were developed and used by Quebec Cartier Mining Company at its iron ore mine in northern Quebec. In addition, a Predictive Maintenance Program (PMP) using vibration analysis will be introduced . This paper discusses the three systems.IntroductionIndia is currently undergoing a massive countrywide industrialization and electrification program. Most of the power will be supplied by coal-fired thermal electric plants.One of the mines being developed as part of the over-all program is the Rajmahal Open Cast Coal project in the Godda District of Bihar, approximately 270 km north , and slightly west of Calcutta.The project is based on an agreement signed in January, 1989 between two government organizations - Canadian Commercial Corporation (Ccq and Coal India Limited (CIL). MET-CHEM Canada Inc. (MET-CHEM), an international consulting engineering organization which has worked in India since 1976, is CCCs Canadian executing agency for the project. METCHEM was the engineer-constructor and mining associate for the development of the 7.5 mtpy Kudremukh Iron Ore Project. This US$430 million project was completed on schedule and under the original budget estimate. The Rajmahal deposit is the responsibility of Eastern Coalfields Limited (ECL), a subsidiary of CIL. The project is to produce coal at the rate of 10.5 million tonnes per year in 1994."

Jan 1, 1991

By S. Asano

Hydrometallurgical processes for treating copper sulfide concentrates have attracted considerable attention over thirty years and many processes have been developed. However there have been still problems in those processes because of difficulties of iron removal and high purity copper production with low operating cost. Although SX-EW is highly cost effective method, it is difficult to process the chalcopyrite. Sumitomo Metal Mining Co., Ltd. (SMM) conducted a review of hydrometallurgical copper concentrate processing and has successfully developed a novel process for the hydrometallurgical production of copper from copper concentrate. In this process, copper sulfide is leached by chlorine gas under atmospheric pressure. Most of hydro metallurgical processes can leach only some of chalcopyrite under atmospheric pressure then they need high pressure leaching facility like autoclave. In this process, copper in chalcopyrite can be leached completely by controlling oxidation reduction potential and chloride ion concentration. Cu(I) ion in leached liquor is separated from Fe(I!) ion by SX using TBP then pure copper powder is produced by electrowinning. Results in batch and continuous testworks and pilot plant tests at Niihama Research Laboratories are presented in this paper. Cu2007

Jan 1, 2007

By Meifeng Zhi, Yuqing Niu, Xixin Chang, Fengqi Zhao, Weimin Qiu, Hao Wang, Zhenqian Wen, Zujun Shu

An applicable Eluex process was developed for acid in-situ leaching (ISL) uranium mine in Bayanwula. In this process, uranium was adsorbed with strong base anion resin from the pregnant solution, then the loaded resin was eluted by sulfuric acid. After D2EHPA extraction, the concentrated eluate was enriched, and the loaded organic phase was stripped by sodium carbonate. The yellow cake was obtained by sodium hydroxide precipitation at last. The uranium concentration in the loaded strip solution was 52.8 g/L. Parameters of the process were determined, and the impact of the Eluex process in underground leaching was also investigated. In industrial design, 95% of raffinate went back to elution and 5% back to in-situ leaching. No significant effect on uranium leaching or resin adsorption was found.

Jan 1, 2020

By Kenneth Blower

This paper gives a detailed coverage of the ore flow through the primary crusher, cobbing plant and concentrator, including equipment sizes, recoveries, reagent consumptions and product descriptions. Special features, such as rubber chutes, rubber-lined mills, pebble-mill grinding, steam-hooded filters and process control instrumentation, are also discussed.

Jan 1, 1968

By Robert B. Parsons

"One of the disadvantages of the federal government&apos;s idea of ""taxation by consultation"" is that it seems to take longer to enact new legislation. The proposed new rules for taxing automobile benefits is one example. Here is a ball which has been batted around between government and the public several times and still has not come down to earth. Fasten your seatbelts, there may be more to come. IntroductionThe draft legislation released on April 13 contains the details of the government&apos;s current proposals on car expenses and benefits. They differ significantly from the last announced position. Finance Minister Wilson has indicated that the release in draft form will provide an opportunity for the Commons Standing Committee on Finance and Economic Affairs (the Blenkarn committee) and other interested persons to comment before the legislation is introduced in Parliament. Accordingly, there may yet be revisions.Notwithstanding the prospect of further changes, the proposed rules generally come into force in 1988. While taxpayers may welcome some of these changes, particularly the increase in the tax-exempt allowance, many must be frustrated that, at this late date, the rules for the current taxation year are not yet finalized."

Jan 1, 1988

By J. P. McGeer

"With the ever-increasing flood of new science and technology has come a new approach to design. The combination of these factors has produced an ever-accelerating pace of materials substitutions.Examples to illustrate the points made above will be given. An overview of the current new materials fields will follow. Finally, the particular nature of the challenge for Canada will be discussed. IntroductionThere are a number of forces currently at work which make it mandatory that the Canadian resource sector re-examine its strategies and policies. The author thinks there need to be very significant changes in the business plans of Canadian mineral processing corporations. Current changes in our environment demand such a reaction.The changes in our environment include more rap id substitution of materials; a significant alteration in design philosophy; the global economy; and market saturation and market diversification in dev eloped countries.This paper will cover the changes and illustrate how they will affect the Canadian resource industry. It will show some of the ways that Canadian corporations are reacting to maintain profitability. Finally, some policy issues will be considered"

Jan 1, 1988

By R. R. Irrinki

Abstract -The Key Anacon deposit consists of four sulfide zones called, from south to north : Key Anacon No. 1, Key Anacon No. 2, Key Anacon No. 3, and Key Anacon Copper Zone. Massive sulfides of zones 1, 2, and 3 are underlain by rocks correlated with the Nepisiguit Falls Formation and are overlain by matie volcanic rocks correlative with the Boucher Brook Formation. In contrast to zones 1, 2, and 3, narrow northwesterly-trend.ing, copper-rich fracture zones occur within the Patrick Brook Formation. Sulfides in zone 2 occur as three mineralogical associations, namely: pyrite-chalcopyrite, pyrite-sphalerite-galerta, and pyrrhotite-sphalerite-galerta. The distribution of lithologies and en-echelon patterns of the three sulfide lenses of Key Anacon No. 2 zone are the result of F1 and F2 folding. Zone 2 is the most promising economically, with proven reserves of 1.11 million tonnes grading 0.2207o Cu, 3.47% Pb, 8.41% Zn, and 96 g/t Ag; the zone is open below a depth of 427 m.

Jan 1, 1992