Search Documents

By Randolph A. Pax, Brian Cornish

The operation of grinding mills in an ore processing circuit is supported by monitoring the input and output variables. These can include the feed ore size distributions, ore feed and water addition rates. The outputs can include the discharge undersize density, oversize tonnage rate and the P80 of the discharge. The grinding mill performance is judged by the power draw, recycle rates and discharge grind size. Conditions inside the mill are inferred from loads cells or bearing pressures and past histories. An overall noise value is sometimes used to evaluate the load as well as the occurrence of excessive impacting of steel balls onto the liners/lifters of the mill. This paper presents results of the internal behaviour of a mill using non-contact stationary microphones located close to the mill outer shell (Pax, 2012). The noise generated by a mill can be attributed to a number of events that occur inside these mills and suitably analysed can provide real-time determinations of in-mill behaviour and can provide powerful insights into the operation of the primary comminution tumbling mills. The acoustically determined signals including a specific 'steel' signal, water hold-up, integrated area together with a classification of impact events. Specific results from case studies will show information of the trajectories inside a mill, steel to rock ratio as well as rheology effects. By incorporating a self-consistent understanding methodology for the in-mill processes from an array of microphones, the information can be used to diagnose the dynamic conditions inside a mill.

Jan 1, 2016

By G. Swan

"The selection of material comprising a backfill is, of economic necessity, site dependent. Nevertheless, given the existing range of typical components-coarse waste, alluvial sand, tailings a balanced or optimal choice is no straightforward matter. A new design approach toward deciding what constitutes an optimum combination of backfill material promises to be useful. In particular a 'binder ' number, based on the mean distance between aggregate particles, specific surface and cement content, is proposed. Using this number, related empirically to compressive strength, the expected mechanical performance of any cemented fill can be predicted.IntroductionOver the years a considerable volume of information has accumulated on mine backfill material design. The principal aggregate component has been deslimed mill tailings, though more recently admixtures of rock waste, sand and tailings are quite common. For these materials uniaxial compressive strength and percolation rate properties are known to be controlled by, among other things, aggregate grading. While empirical formulae exist for relating grading to percolation rates, considerable uncertainty exists concerning strength development."

Jan 1, 1985

By Stephan Day

Comments on Robust M3 to Protect Water Quality ?Regulatory and philosophical thinking have tended to evolve at decade scale since 1970s. ?Mines typically last more than a decade. ?Robustness is defined by the ability to adapt to new realities. Managing Water Quality in BC ?1973 ?BC Pollution Control Objectives ?1977 ?Federal Metal Mine Liquid Effluent Regulation (Fisheries Act) ?Late 1980s ?Philosophy of ?Designing for Closure? ?1990s ?Designing for Acid Rock Drainage Management ?2000s ?Awareness of need for water quality management in general, regardless of acidity

May 1, 2010

By Pierre O'Dowd

"The southern Abitibi Belt is the major source of gold in Quebec. Although the northern part of the belt is quickly being developed, the area under study will not be downgraded in the near future because it still contains more than 75% of the known reserves in the belt.Gold is found in a variety of geological environments which are part of a small number of distinct structural patterns. For the exploration geologist, outlining such patterns might be easier and more productive than defining, when it is possible, the exact genetic nature of the gold mineralization.Exploring in the right place has always been one of the main concerns of explorationists. This paper briefly describes the various favourable geological settings, and outlines areas, types of structure and lithologies of high potential for gold exploration in the southern Abitibi Belt.IntroductionThe southern part of the Abitibi Belt is a profilic mining area for precious and base metals (Lulin 1990). Although mineralizing processes and controls of polymetallic deposits are well known and understood (Lydon 1984), almost every gold occurrence is a unique case and numerous models have been proposed (Roberts 1987; Hodgson and McGeehan 1982; Hodgson 1990).This study does not define new genetic models for the formation of gold deposits, neither is it meant to elaborate on the existing ones. A genetic approach, is by definition, theoretical and, to some extent, universal. It helps geologists define types of targets and exploration tools but does not outline or quantify target areas. To tentatively summarize the complexity of a genetic approach, a brief discussion on the various genetic models in vogue in Abitibi and the problems related to their use in exploration can be found at the end of this paper."

Jan 1, 1991

By P. A. Geusebroek, N. A. Duke

Abstract - The Lupin mine, located in the central Slave province just east of the western boundary of Nunavut Territory, is a world-class example of a Neoarchean-aged banded iron formation (BIF)-hosted lode-gold deposit. At the minesite the gold-mineralized Lupin BIF, separating stratigraphically underlying psammitic wacke and overlying argillaceous turbidite sequences, delineates the Lupin dome, a hammerhead-shaped F2/F3 interference fold structure occurring at the greenschist to amphibolite facies metamorphic transition within the thermal aureole of the Contwoyto batholith. Detailed paragenetic relationships indicate that peak thermal metamorphism coincided with the switch from regional D2 compression to rapid D3 unroofing of the Neoarchean orogenic infrastructure. Gold initially precipitated with pyrrhotite, replacing amphibolitic BIF at the apex of the Lupin deformation zone, separating the east and west lobes of the Contwoyto batholith. Over the course of associated prograde/retrograde metasomatic overprints, gold was further remobilized during garnet and loellingite/arsenopyrite growth in chlorite-altered selvages of late-forming ladder quartz veins. A metamorphic model of ore genesis, with gold being scavenged and transported by metamorphic fluid that was shed and structurally trapped at the amphibolite recrystallization front, is favored over the previously proposed syngenetic and exogenic models of gold concentration that have tended to polarize genetic interpretations to date.

Jan 1, 2004

By Owsiacki. Leo

Both the 8 and A-C ore zones of the Heath Steele Mine contain extensive areas of brecciated ore. This texturally distinct ore type has been tentatively defined as a fragmental or conglomerate massive sulphide. It consists of subangular and round fragments of pyrite up to 30 em in diameter, smaller quartz clasts and chloritized, mineralized, lithic fragments in a faintly banded matrix of pyrrhotite and chalcopyrite. The chalcopyrite is concentrated in the pressure shadows of the fragments and appears to reflect remobilization and recrystallization during a deformation which postdates the formation of the clasts. A generally conformable relationship with the underlying banded pyrite-sphalerite ore, discordancy with the host banded argillites, spatial distribution and similarity to Kuroko ores suggest that the fragmental ore is of primary origin and that breccia formation is probably due to soft-sediment slumping or sliding initiated by volcanic explosions, as hypothesized for similar massive sulphides in various Japanese mines. It is nevertheless recognized that certain structural features in some clasts may result from deformation preceding the formation of the breccia, and at this stage a tectonic origin cannot be completely eliminated.

Jan 1, 1979

By E. Rosseland

Glencore Nikkelverk is operating its Chlorine Leach Process in Kristiansand, Norway, producing nickel, copper and cobalt metals by electrowinning. The copper tankhouse, with an annual capacity of 40 000 tons, is based on traditional technology with copper starting sheets and cast lead anodes. Due to the integration of this copper sulphate process in a nickel chloride refinery, operating conditions are unique. In recent years, operating costs have escalated, and health, safety and environment are top priorities. Test work on a new copper process involving permanent cathodes was therefore initiated in 2007, and a pilot plant was started up in 2012. The objective was to introduce innovative technologies and tailor these to be robust in the Nikkelverk process, to form a basis for a new sustainable copper tankhouse with a high degree of automation. Key learnings from more than 10 years of R&D work is presented, focusing on cathode materials and copper metal deposition including product quality, robotic stripping, coated titanium anodes, electrode contacts and alignment, electrode current monitoring with Hatch HELM tracker technology and acid mist capture using cell hoods with off-gas scrubbing. The new copper tankhouse project was approved in December 2018, and commissioning is planned in 2022. INTRODUCTION The Kristiansand nickel refinery was started up in 1910, processing nickel-copper matte originating from Norwegian mines. It was the first industrial plant in the world to produce nickel by electrolysis using the Hybinette electrorefining process. After roasting to burn off sulphur in the matte, copper was leached and recovered as cathodes by electrowinning with lead anodes. In the first years, the copper cathodes were fire- refined and cast into ingots for sale (Thonstad Sandvik, 2004). The Nikkelverk refinery was acquired by Falconbridge Ltd. in 1929, and since then matte from Sudbury, Canada has been the main feed source. The Hybinette process was in operation until 1975 when conversion to the newly developed Chlorine Leach Process was started (Stensholt, Zachariasen, & Lund, 1986). In this process still used today, nickel and part of the copper in the matte is leached using chlorine gas generated on dimensionally stable anodes in the nickel and cobalt electrowinning tankhouses, as illustrated in Figure 1. The presence of dissolved copper ions in the strong chloride leach solution is essential for effective chlorine absorption and nickel dissolution. To improve copper-nickel separation, slurry from the atmospheric leach is pumped to autoclaves and then to cementation tanks for precipitation of copper as copper sulphide, which is collected in filter presses. The leach residue, also containing the precious metals, goes through a 3-stage wash to remove chlorides before being introduced as a slurry to fluid-bed roasters for sulphur removal. The resulting calcine is then leached in spent electrolyte from the copper electrowinning tankhouse, to dissolve most of the copper and also some nickel, cobalt and other elements. After separation of the leach residue, elements like Bi, Te, As and Ag are removed from the strong copper sulphate solution by reaction with metallic copper in three columns in series filled with cut copper cathodes. The purified solution then passes polishing filters before being mixed with spent electrolyte and returned to the electrowinning cells.

Jan 1, 2019

By P. E. Weidmark

"CANMET InformationPART 1-Published PapersAsmis, H. W., ""The dynamic response of caverns in discontinuous rock""; Proc 22nd U.S. Symposium on Rock Mechanics, Cambridge, Mass, June 1981, 272-277; 1981.Austin , M.W., Bray, J.W. and Crawford, A.M., ""A comparison of two indirect boundary element formulations incorporating planes of weakness"" ; Technical Note; Int J Rock Mech Min Sci Geomech Abstr; 19:339-344; 1982.Barrett, J. R., ""Applying geotechnical theory to underground metalliferous mining""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 210-222; 1983.Barron, K., Wright, P.L. and Smales, T., ""Guideline s for the design of coal pillars in the No .4 seam at Mclntyre Mines Ltd ., Grande Cache, Alberta""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of A IMMPE; 559-578; 1983.Bauer, A., ""Wall control blasting in open pit mines""; Mining Engng; 34:155-158; 1982.Bieniawski, Z.T., "" Improved design o f room-and-pillar coal mines for U.S. conditions""; Proc 1st Intnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 19-51; 1982.Blackwell, G.H. and Calder, P.N., ""Practical aspects of wall stability at Brenda Mines Ltd., Peachland, BC""; 3rd Intnl Conf on Stability in Surface Mining; Vancouver, BC, June 1981; SME-A1ME; 3:573-608; 1982.Blake, W., ""Microseismic monitoring for underground stability "" ; Proc 1st Intnl Cont on Stability in Underground Mining; Vancouver , BC, August 1982; SME of AIMMPE; 272-294; 1983.Brawner, C.O., ""Stabilization of rock slopes"" ; 3rd Intnl Conf on Stability in Surface Mining; Vancouver, BC, June 1981; SME-AIME; 3:289-310; 1982.Bridges, M.C., ""Review of open stope mining in Australia""; Proc 1st lntnl Conf on Stability in Underground Mining; Vancouver, BC, August 1982; SME of AIMMPE; 813-828: 1983."

Jan 1, 1983

By M. Remillard, M. Garon, D. Hodouin, M. Therien

"Nineteen streams in the copper and zinc flotation units of the concentrator of the Matagami Division of Noranda Inc. have been sampled f or particle size distributions, chemical assays, and gold and silver contents in each particle size interval. The data are upgraded by the mass balance package BILMA T. These results, in conjunction with microprobe analyses, are used to quantify the silver losses in the copper cleaning flotation stages and to determine how over-all silver and three silver-bearing minerals are recovered in the plant final products. RESUMEDix-neuf produits des circuits de flottation du cuivre et du zinc de la division Matagami de Noranda Inc. ont été échantillonnés pour leur distribution granulométrique, leurs analyses chimiques et Ie contenu d'argent et d'or des fractions granulométriques. Le bilan métallurgique a été obtenu à l'aide du programme BILMA T. Ces résultats, couples avec une étude minéralogique a fa microsonde, sont utilisés pour quantifier les pertes argentières aux diverses étapes de nettoyage du circuit de cuivre et pour déterminer la répartition de l'argent et des trois minéraux argentifères dans les produits finals de l'usine."

Jan 1, 1988

By John A. Herbst, Gerald H. Luttrell, Jaisen N. Kohmuench, Aaron Noble, Michael J. Mankosa

The HydroFloat TM is an innovative fluidized-bed separator that can substantially increase the upper particle size that can be successfully treated by flotation. Recent studies conducted using laboratory, bench-scale and pilot-scale equipment indicate that this technology can be used to float coarse sulfide middlings that cannot be recovered by conventional flotation machines. Recent data collected from pilotscale tests conducted at a base metal concentrator indicate that this technology can float middlings particles as large as 850 microns in diameter containing as little as 1% exposed hydrophobic mineral. As such, the crossover of this technology into the base metals industry has the potential to substantially reduce grinding costs and increase concentrator recovery/capacity through the use of split-feed circuitry. The split-feed concept, which is often used for upgrading industrial minerals, involves segregation of the feed into more than one size class followed by subsequent upgrading using mills/separators/reagents specifically optimized for each size class. In this article, a split-feed circuit is described that utilizes two stages of classifying cyclones in conjunction with the HydroFloat_ separator. The circuit is designed to recover, recycle and regrind coarse middlings containing small amounts of valuable mineral while simultaneously rejecting coarse well-liberated siliceous gangue so that mill throughput can be increased. Simulation data conducted using well-known process models suggest that this approach can increase existing primary mill capacity by up to 25% with only modest investments in new classifying and flotation equipment.

Jan 1, 2016

By P. Rocque, S. Talebi

Although the measurement of blast vibration close to the blasthole is critical to the understanding of rock fragmentation mechanisms and blast damage in the rock masses, limited experience for such monitoring exists. Because much higher vibration amplitude and frequency ranges are expected in rock masses close to an explosive charge as compared to far field vibrations, different problems from those for the far field monitoring must be considered for near field blast vibration monitoring. Currently, guidelines for design of the near field blast monitoring systems do not exist. This paper describes the development of an integrated technique for vibration monitoring close to a blast hole, including selection and installation of transducers, design of a monitoring system and signal recording. A densified cement was designed for grouting accelerometers in order to match p-wave impedance between the rock and grout. The monitoring technique described has proven suitable for blast vibration monitoring within 2 m to 15 m of a blast hole having loading conditions similar to production blasts.

Jan 1, 1993

By G. W. R. Kuzyk

"Hydraulic drills, recently implemented at the Tantalum Mining Corporation of Canada, Limited, Bernie Lake Mine, are proving to be an economic alternative to pneumatic drilling systems. The paper describes the application of an electric-hydraulic drill jumbo to the mechanized room-and-pillar mine and its performance. The application of these drills resulted in improved environmental and working conditions.Drill rods and bits are a major cost centre in hard-rock mining applications. The paper also discusses the performance of one manufacturer's product used on the hydraulic drills.IntroductionThe Tantalum Mining Corporation of Canada, Limited (TANCO) started producing tantalum ore from its Bernie Lake pegmatite in 1969. The pegmatite, encased in amphibolite, is shallow seated and flat lying. It is defined by diamond drilling along 4,000 feet of strike and 1,500 feet down dip, ranging in thickness from 60 to 280 feet. Relatively well defined zones of mineralization occur within the pegmatite and form separate orebodies of tantalum, lithium and cesium."

Jan 1, 1981

By Robert B. Parsons

"The Department of Finance introduced draft amendments to the resource allowance regulations on July 23, 1992 that effectively nullify the decision in the Gulf Canada Limited case. Prior to the amendments it appeared that only ""directly"" related general and administrative, capital cost allowance and scientific research expenditures had to be deducted from resource profits. Now ancillary expenditures are required to be deducted. Consequently, the ability of taxpayers to claim the resource allowance is curtailed.IntroductionOn October 25, 1990 it was almost certain that taxable mines were going to get a break. The Federal Court-Trial Division had just decided in Gulf Canada Limited's favour to allow it to claim resource related tax benefits larger than what Revenue Canada evidently wished. Revenue Canada appealed first to the Federal Court of Appeal and then to the Supreme Court of Canada. On January 10, 1992 the Federal Court of Appeal agreed with the Federal Court decision and on July 2, 1992the Supreme Court declined to hear any further appeal. A mere three weeks later, on July 23, 1992, the Department of Finance issued draft ""clarifying"" measures to amend the calculation of the resource allowance. These measures effectively nullify the benefits that arose under the decisions of the Federal Court."

Jan 1, 1992

By C. A. Roloff

Demands for increased grinding production, lower-grade are and limited capital have resulted in ever larger grinding mills, some as large as 36ft (/1 m) in diameter and 12,000 hp (8,950 kw). The result is often f ewer machines per plant, with a greater dependence on each machine. To meet these reliability requirements, manufacturers of mills, drives, castings and other components have had to be innovative and creative in their design. Only by thorough review of past designs and practices and by model studies confirmed in field tests can the manufacturer have full confidence in the product. Because of the great interest in large mills, a short review of larger machines is presented. This discussion covers material feeding, bearings, the rotating element, drive trains and material discharge.

Jan 1, 1979

By A. Himsley, E. Byleveld

"With reference to the chemical constraints underlying the ion exchange process for uranium recovery, a generalized view is presented on the actual and the achievable efficiency of the process. The area considered is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution.A comparison between actual plant results and the chemical requirements shows that:(a) Unless new and better ion exchange resins are developed, no dramatic change in equipment size and resin inventory is""anticipated. (b) Elution efficiency, especially for sulphuric acid, may be improved considerably. More concentrated eluates may beproduced at lower chemical consumption. A possibility of achieving additional purification solely by ion exchange is discussed.IntroductionThis paper presents a generalized view of the actual and the achievable efficiency of the ion exchange processes for urannium recovery. The study is restricted to acid leach circuits in combination with nitrate, chloride or sulphuric acid elution. The ultimate efficiency attainable with ion exchange is dietacted by the chemical reactions underlying the process. The most sophisticated technology cannot change the diffusion rates in the ion exchange resin nor make the uranium loading exceed its equilibrium valueThe design of an ion exchange plant for uranium recovery involves a considerable number of parameters as a result of the wide variety of pregnant solutions produced from different orebodies. Therefore, a generalized approach of the ion exchange process inevitably neglects some parameters which maylead to significant variations in apparently identical situations.The uranium concentration in the pregnant solution, together with its pH, are the principal variables which determine resin loading and residence rime in the ion exchange system. On the elution side, the type of eluant and its concentration will determine the contact time required and the amount of eluant needed to strip the resin. The temperature, the properties of the ion exchange resin, the total dissolved solids in the feed solution and the competing ions are other variables that affect the chemical performance; these, however, may be considered as a correction of the principal parameters if one is interested only in general trends."

Jan 1, 1980

By G. K. Livingstone

"This paper describes mining conditions in the Kaiser surface and underground coal mines in the Sparwood area of southeastern British Columbia. Mining methods are explained, major mining equipment is listed and production rates are given. Reclamation methods and results are described. Data are given on safety organization, safety practices, accident statistics, safety inspections and absenteeism. IntroductionThe coal mines of Kaiser Resources Ltd. are located in the southeast corner of British Columbia. All present mining is in the Sparwood area, where operations began in 1900 with the opening of the Michel underground mines. Production increased rapidly at first, then went through successive periods of depression and prosperity. Following are the highlights. Quantities are in clean, short tons. 1900 1910-Rapid rise in production to a peak of 512,000 tons in 1910.1911-1924-Reduced rate of production, averaging 238,000 tons per year, due to strikes, manpower shortage during World War 1 and post-war depression.1925-1929-Second prosperous era, with production climbing to 383,000 in 1929.1930-1933-Second depression-production falling to 231,000 in 1933.1934-1942-Third era of prosperity-production recovered and new production peak of 908,000 tons reached in 1942 during World War II.1943-1956-Corttinued prosperity, with production averaging 720,000 tons per year.1957-1959-Loss of markets to oil and gas; production dropping to 517,000 tons in 1959.1959-1969-Recovery due to new coal market in Japan; production climbing back to the 900,000-ton level.197D-Present-Jump in production reaching 6.6 million tons in 1975. This was the result of the purchase of the property by Kaiser Steel, who negotiated a large-volume, long-term contract with Japan, built the coal port of Westshore, reduced shipping costs by instituting unit trains, and reduced production costs by investing in large-scale mining machinery and a new preparation plant."

Jan 1, 1980

By J. G. Conaway, P. G. Killeen

"Gamma-ray spectral logging, a useful technique for uranium exploration and evaluation, has generally been underutilized by the Canadian mining industry. Provided that the technique is properly applied, it is capable of yielding reliable quantitative information regarding the distribution of uranium and other radioelements along the borehole under most conditions.In practice. there are numerous factors which potentially can degrade the quality of the log and thus any quantitative interpretation based on it. Fortunately, the appropriate choice of logging equipment and technique can avoid many such problems, and corrections can be applied to the data to compensate for most of the others."

Jan 1, 1980

By Carl Edmunds

Talk Outline Deposit?s Vital Statistics and Economic Environment Regional Geologic Setting Deposit Geology UBC Research Search Model and Current Exploration Plans Kemess Operations Kemess South Mine Mining rate (2006) ?135,000 tonnes / day Mill throughput (2006) ?52,000 tonnes / day Average Annual Production ?300,000 oz gold and 75 million lbs copper ?Production until mid-2009 Kemess North > Open pit reserve 423.8 million tonnes @ 0.3 g/tgold and 0.18% copper > 4.1 million ounce gold reserve (127 tonnes) > 1.45 billion pound copper reserve (636,000 tonnes) > 0.75:1 Strip Ratio

May 1, 2006

By Sukumar Bandopadhyay, Arunapuram Sundararajan

"For the last three decades, the application of network planning has provided a basis for a formal and general approach to the discipline of project management. For fixed activity duration, a very simple algorithm commonly known as critical path method (CPM), gives the length of time required for the total project as well as indicates the activities which are vital to the completion of a project. Project Evaluation Review Techniques (PER T) on the other hand, generalize the above approach to recognize uncertainty in the activity durations by allowing them to be random variables. One of the misleading aspects of current "" PER T"" solution method is, however, the implication that there is a unique critical path. In general, any number of paths could be critical, depending on the particular realization of the random activity durations that actually occur. In this case, simulation can be utilized to estimate completion time of a project.In this paper, the concept of criticality indexing is discussed, and a simulation model application which defines the critical path based on the criticality indexing concept, to a longwall development - extraction network, is presented. The model also provides suitable scheduling of resources based on the resource constraints and smooth s out period-t o-period assignments. IntroductionThe successful management of large-scale projects require careful planning, scheduling , and coordinating numerous interrelated activities. To aid in these task s, formal procedures based on the networks and network techniques (variously called PERT or CPM) were developed. In its original form the completion time for individual activities of a project was assumed fixed and known in advance: this in turn led to the familiar algorithms for computing the critical path, earliest start time, slack, and so forth. The unreality of such an assumption is, of course , apparent in many contexts. Consequently, attempts were made to introduce probalistic activity completion times, allowing representation of the stochastic nature of most projects."

Jan 1, 1987

By A. D. Hunter, J. M. JR. Moore

"The Aldermac deposit and associated prospects occur in the Noranda Archean volcanic centre of the Abitibi greenstone belt. Over two million tons of are grading 1.65% copper, with minor gold and silver, were mined between 1933 and 1943. The deposit has features in common with the Vauze and Millenbach mines in the same district.Recent detailed mapping, geochemistry and petrography combined with data from former diamond drilling and mining operations permit a re-interpretation of the Aldermac area. The orebodies and spatially related sulphidic zones are con eluded to be volcanogenic.The host rocks are a chemically bimodal suite of mafic and rhyolitic flows, volcaniclastics and related subvolcanic intrusions. Massive sulphide lenses are spatially related to a quartz-feldspar- phyric rhyolite dome and siliceous, volcanic-exhalative sedimentary rocks, The succession is cut by gabbro and syenite, related to later stages of volcanism, and by post Kenoran diabase dykes. Regional metamorphism attained the low greenschist facies, but the rocks lack penetrative deformation.Hydrothermal alteration is primarily an intense silicification of mafic volcanic rock s enveloping, or lying below, sulphidic zones. Chlorite and sericite alteration zones, including dalmatianite, are more locally developed and have a closer spatial relation to mineralization, as do epidote, calcite and calcic garnet.The structure is complex and cannot be explained by isoclinals folding; rather it reflects concurrent faulting, and extrusive and intrusive activity. Fault blocks were rotated and exhibit opposed facing; the original selling was possibly a submarine graben.Sulphidic zones occur within mafic and felsic volcanic rocks and at the interface between the two; there is thus potential for discovery throughout the known stratigraphic succession. Exploration conducted according to a volcanogenic model is advisable, particularly in the light of recent discoveries in similar rocks of the Amulet area."

Jan 1, 1983