Search Documents

By T. H. Patching, M. W. Mikhail

"The gas sorption and emission characteristic of coals are important to the planning and conduct of mining operations. Methane drainage from coal strata can also provide a supply of fuel in certain circumstances. Gas emissions have also created hazards during the handling and transport of coals and the release of gas also appears to be related to the yield of fine sizes during mining and processing operations.This paper summarizes studies at the University of Alberta on the permeability and gas emission of certain bituminous coals. Permeability of 'solid' samples was found to be drastically reduced by confining pressure. An emission index, .P, which has been related to outbursting behaviour of coals, has also been related to the proportion of fine s in cleaning plants. Gas sorption isotherms are dependent on temperature, moisture content, the gas involved and the type of coal and can be approximately expressed by the Langmuir or the Freundlich equations. Sorption values in sections taken across a given seam were similar but considerable differences were found in . P indices in the different coal layers of a seam.IntroductionThe emission of gases, especially of methane, from coal has been a subject of great interest (and sometimes a matter of life and death), to those who dig and handle coal since it was first mined from underground pit s. Many studies and investigations have been carried out on gas occurrences and emissions but our knowledge of the precise mechanisms of gas sorption, desorption and flow from coal is still incomplete. It is the purpose of this paper to review the principal factors involved in these processes and to briefly rep ort some of the results that have been obtained by studies in the laboratories of the Department of Mineral Engineering, University of Alberta, and Coal Research Laboratory, Edmonton, CANMET"

Jan 1, 1986

By P. K. Chatterjee

"The operations of a large-scale open-cut mine are simulated to produce a user-oriented interactive digital model. SIMULA is chosen as the programming language and a sophisticated data base system is designed to consider the complex information network of large mines. The main features of the program are the mine planning and mine evaluation modules. These modules are responsible for the computation of truck-shovel performance and other equipment details in a mine. Stochastic methods are employed to generate event times. The use of a Data Base Management System and the data base provide an efficient method of information storage and retrieval. Truck allocation techniques have been examined in detail and comparisons between random dispatching and conventional methods are made. The model is intended for mine operators and engineers and the program is well structured and very readable. It is hoped that these features will make the model readily acceptable.IntroductionThe Department of Mining and Metallurgical Engineering at the University of Queensland has been conducting research into computer simulation methods in mining since 1972. The research has been mainly applied to actual operations, with both open-cut and underground mining being equally emphasized. The results of the research to date have not only strengthened the methodology of the approach to complex mining problems, but have also increased confidence in the use of modelling and computer simulation technique s in mining.The model described in this paper translates a complex LHD situation into a user-oriented interactive digital model using SIMULA. The present methods of evaluating truck dispatching and trolley assist are tedious and laborious. This model provide s the engineer with readily acceptable means of rapidly assessing the relative merits of these techniques in a large-scale open-pit operation. Poor utilization figures in many current operations (for example, 40% for trucks, 70% for shovels) are of serious concern to mine officials and computer-controlled dynamic truck dispatching systems have been considered by some of these mines to improve equipment utilization ."

Jan 1, 1981

By J. S. Stachulak

"IntroductionInco Limited operates nine underground mines on the rim of the Sudbury Basin. These operation s are situated near the city of Sudbury, 589 km west of Montreal, and 363 km north of Toronto. The ores are mined primarily for nickel and copper, and the principal minerals are pentlandite, chalcopyrite , and pyrrhotite. Total ore production from underground is in excess of 51 000 tons per day.The total volume of fresh air supplied to the nine mines is six million cu.ft/min. There are 50 main fans in operation at these mines, powered by electric motors totaling 11 200 kW (15 000 hp).The trend in metal mining during recent years towards mechanization and high-tonnage production methods has greatly increased ventilation requirements. The now of air must quickly dilute and carry away diesel exhaust fumes, dust created by mining operations, and the fumes of the explosives used in blasting. Mechanical ventilation is required to obtain the necessary volume and control, as natural ventilation pressures alone are, for the most part, inadequate and unreliable. In the event of a mine fire or other needs, close control of ventilation is essential.There are two unique heating systems presently in operation at Inco: Creighton Natural Heat Exchanger and Stobie Ice Stopes."

Jan 1, 1991

By Siavash Zamiran, Abdolreza Osouli

"One of the most concerns of room and pillar mining system is subsidence of the ground surface due to coal mining particularly in room and pillar mines. Subsidence of ground surface is a result of floor, pillar, or roof failure of the mine. At the same, due to many difficulties associated with surface disposal facilities of coal refuse, some mining companies are trying to use underground space as a disposal storage place. In this study, stability and subsidence analyses of an underground coal mine located in the Illinois Basin are conducted. This room and pillar mine was abandoned and later on was used as a storage place to accommodate the coal fine refuse with slurry backfilling method. The geological stratigrophy and geomechanical properties of the mine floor and roof were collected. Floor and pillar stability analyses were conducted for areas with various extraction ratios. The stability of the mine was evaluated both prior and after slurry backfilling. The floor and pillar stability analyses results of the mine due to moisture exposure after slurry backfilling are discussed. The subsidence potential due to mine failure is also evaluated.INTRODUCTIONA typical lithology of coal seams in the Illinois Basin consists of weak underclay stratum. The immediate weak underclay causes frequent floor instability problems in Illinois underground coal mines. There are two different stages in assessing floor stability of the mines where slurry backfilling is planned. The first stage is during the mining operation when weak underclay layer squeezes under pillar stress and results in punching or bearing capacity failure. The second stage is after slurry backfilling. During this stage, the slurry material soaks non-durable floor layers and causes strength reduction in floor material. Pillar stability conditions should also be taken into account during both the operational period and after the slurry backfilling."

Jan 1, 2015

By D. M. Ward

"The uranium deposits upon which the Rabbit Lake project story is based are located at the eastern margin of the Athabasca Basin just west of Wollaston Lake in northern Saskatchewan. This paper provides a general review of the exploration history for the major deposits and the influence of an expanding geological data base, which served to guide the continuing exploration programs.A brief description of each of the deposits is provided in order of their discovery and with emphasis upon their relative geological and mineralogical characteristics.The Rabbit Lake and Eagle Point orebodies are monometallic uranium deposits localized by thrust faults within the Aphebian Wollaston Group. The Cof/ins Bay A-zone, B-zone, and D-zone are polymetaflic U, Ni, As, Co (Au , Ag) deposits located within the Helikian Athabasca Group at its unconformable contact with the underlying Wollaston Group. INTRODUCTIONThis paper demonstrates the importance of applying the accumulated geological knowledge, gained through the exploration, mining, and development process, to the ongoing success of exploration programs. To emphasize this point, the basic geology of each of the major Rabbit Lake area deposits will be presented in chronological order of their discovery and subsequent development. These depos its include Rabbit Lake, Collins Bay A-zone, B-zone, D-zone and Eagle Point. The geological descriptions are based primarily upon the detailed observations of many current and former geologist s employed by both Gulf Minerals Canada Limited and Eldorado Resources Limited. Much of the early historical data was obtained from Dr. E.E.N. Smith, formerly with Eldorado Resources Limited. Regional GeologyThe Rabbit Lake area which includes the Rabbit Lake, Collins Bay A-zone, B-zone, D-zone and Eagle Point deposit s, is located on the eastern edge of the Athabasca Basin close to the western shores of Wollaston Lake (Fig. I). The area is in the Churchill Province of the Canadian Shield within the Wollaston lithostructural domain, at the eastern edge of the Athabasca Group. The uranium deposits occur within both the Wollaston Group metasedimentary assemblage of probable early Aphebian age, and the diagenetic ally altered quartz sandstones and conglomerates of the Athabasca Group of Paleohelikian age. Both units unconformably overlie granitoid gneisses interlayered with metasediments and a graphitic iron formation all believed to be of Archean age. All uranium depo sits in the Rabbit Lake area occur in close proximity to the Paleohelikian - Aphebian or Paleohelikian - Archean unconformity."

Jan 1, 1989

By Desmond M. Levins

"Australia has almost twenty per cent of the Western World's low-cost uranium reserves, located mostly in the Alligator Rivers region of the Northern Territory. At present, only one uranium mill is operating in Australia, but a number of new mills are planned for the early 1980s.Details are given of Australian uranium mining and milling proposals and the measures taken to minimize their environmental impact. Major factors affecting environmental impact are discussed, including treatment of liquid wastes, water management, control of radon and other airborne releases, and disposal of tailings. IntroductionAustralia is entering a new phase in uranium mining and milling activity . In the first phase of operations, between 1954 and 1971, about 10,000 tonnes of yellowcake was produced at five locations. Most of the production came from the mines at Rum Jungle in the Northern Territory and Mary Kathleen in Queensland. In the 1960s, the demand for uranium slumped, and much of the yellowcake produced at Rum Jungle was stockpiled by the Australian Atomic Energy Commission. The early uranium processing operations in Australia were typical of overseas practice at that time. Environmental problems were generally given low priority and pollution control measures were unacceptable by today's standards. There was little or no recycling of process water, acid waste streams were not neutralized and tailings dams were poorly designed. At Rum Jungle, oxidation of sulphides in waste heaps, tailings dumps and ore stockpiles subsequently led to destruction of vegetation and heavy metal pollution in a nearby river.In the early 1970s, major uranium deposits were discovered in the Alligator Rivers region of the Northern Territory. Significant orebodies were also located in the Great Artesian Basin in South Australia, in calcrete formations in Western Australia and at several locations in Northern Queensland. According to latest available estimates. Australia has about 160/0 of the Western World's uranium recoverable below $US 80 per kg U. Mining these orebodies will require pollution control measures more stringent than practised previously in Australia."

Jan 1, 1980

By Fred A. Curtis, Kathryn E. Moore

"The past 14 years have brought an increased awareness of environmental problems. Surface mining for mineral aggregates has been one o f the issues which ha s sparked fierce controversy and debate. Various level s of government, industry, and the public have engaged in an unending battle for adequate planning, regulation, and rehabilitation of pits and quarries. Agreement has seldom been reached and, as a result, few standards, guidelines or policies have been established, or enforced province-wide.Surface mining ca uses a number of environmental problems including noise, dust, water table disturbances, aesthetic degradation, increased traffic, and health and safety hazards. These problems are particularly serious in urbanizing area s, where people are exposed to the mining operations. Associated with the operational phase of surface mining are the issues generated by the multiplicity of abandoned pits and quarries which dot the countryside. These large, gaping, often dangerous waterfilled holes are a blight o n the landscape, and represent a misuse of land.The environmental problems connected with pit s and quarries are compounded by the fact that accessible reserves of mineral aggregates are being lost through the process o f urbanization. In addition, restrictive zoning at the municipal level is restricting access to even more aggregate rich land. This results in the paradox that the very urbanizing process which creates the demand for aggregates is rapidly reducing the available supply. These problems have stimulated the Ontario Ministry of Natural Resources to call for a province-wide program of inventory, assessment and planning for the protection o f high-quality reserves in Official Plans. These proposals have met with strong opposition from municipal leaders, who are jealously protecting their autonomy.Environmental management education is a prerequisite for all parties involved in pit and quarry planning, regulation or rehabilitation. To this end the following bibliography of selected articles with attention given to the Ontario experience, should provide helpful information on these topics."

Jan 1, 1985

By Deni Lessard, Roger Demers, Noël R. Billette

"The Quebec Mining Association has for many years been supportive of the activities of the Centre de recherches minérales which were initiated to ensure regular production hoist and cable inspections to maintain safety and productivity standards in underground mines in Quebec. CRM and CANMET have agreed to fund a Quebec Mineral Development Agreement contract to capture this accumulated knowledge. Using VP-EXPERT to process the information and subdirectories to store regulations, the prototype access D-BASE III records on hoist information and LOTUS 123for simulating working conditions that meet local regulations and expert rules of thumb criteria. Objectives are to improve safety in emergency operating procedures, maximize hoist productivity and safety, and promote knowledge transfer to operators."

Jan 1, 1992

By H. W. Smith, D. Guerin

"This paper describes the development of a dynamic model for a full- scale (64 tonnes/hr) grinding circuit consisting of an open-circuit rod mill feeding a ball mill operating in closed circuit. The object of constructing such a model is to investigate the static and dynamic behaviour of potential control schemes. Model selection, data processing and parameter estimation are discussed, and static and dynamic results of simulations are presented. Conclusions are drawn with regard to the adequacy of the model for such studies, and likely limitations on control of such circuits.IntroductionThe model developed here is intended to represent the grinding behaviour of the grinding circuit at the Lake Dufault division of Falconbridge Copper Mines Ltd. This circuit has been fully described elsewhere. At the time of the work described, the ball mill discharge was fed to a four-cell flotation bank , the tailings of which are combined with the rod mill discharge in the cyclone feed pump sump. As the emphasis in this study is on grinding behaviour, and as only I per cent of cyclone feed material is removed in these cells, no attempt has been made to include flotation behaviour in the simulation. One effect of the presence of flotation cells in the grinding circuit is, however, to necessitate somewhat finer grinding than might otherwise be needed: this will have effects on mill parameters.The paper is organized as follows. First the selection of models is discussed, paying particular attention to the problem of selecting simple, yet adequate, flow models for the mills. Then data gathering is described. The method of deriving mill model parameters is explained, and the results presented. Mass balancing of cyclone data and the determination of cyclone model parameters are described. The linking of the models into a full simulation is outlined, and sta tic and dynamic results presented. Finally, the results are discussed and conclusions drawn ."

Jan 1, 1980

By D. Moffat

Rio Algom Limited has mined uranium at Elliot Lake, Ontario for 20 years. The production of this energy-generating element results in the need to dispose of low-level radioactive solid wastes and liquid effluents. Because of the wet-temperate climate at Elliot Lake, the liquid effluents are of particular importance. Radium-226 is the isotope which requires most attention, and the current practice for its control is by addition of barium chloride and retention of the resultant precipitates in large settling ponds. Analyses of typical effluents and waste streams are discussed and typical levels of radium-226, thorium-230, thorium-232, thorium-228, lead-2iO, polonium-2iO, and uranium isotopes are presented.

Jan 1, 1979

By Chaluvadi K. Sridhar, Prashanta K. Chatterjee

"IntroductionThe planning of an underground coal mine requires a complex blend of technical expertise, experience and subjective design criteria implemented by the mining engineer. Currently the procedure is largely manual and requires considerable resources to generate a single mine plan. Often three or four people are assigned to work in the development of a single draft layout. Evaluation of the layouts is also tedious as it requires many repetitive calculations. The evaluation of layouts developed manually generally attempts to derive a single economically feasible solution. Operational constraints in underground coal mining such as manpower, time, equipment, etc., do not allow the generations of more than one alternative layout. As a result, the first plan is generally the only one considered.Computer-aided mine planning can automate many of the manual procedures and calculations involved in mine planning thus allowing to evaluate man y layouts and mining strategies and to select the optimum plan with confidence. An optimized planning procedure will also provide the capability to evaluate mine performance continuously and critically, thereby helping to maximize return on investment. Although recent advances in computer graphics have provided the hardware necessary for developing and evaluating min e plans rapidly, software that will allow the mining engineer to make use of the new technology is slow in developing. The need for such software packages has been recognized and ackowledged.At several sessions in recent conferences on the applications of computers in the mining industry, the use and benefit s of computer-aided mine planning were discussed. However, there were few papers presented that referred to actual applications of interactive graphics to underground mine planning. The emphasis of this study is toward the development of a completely integrated computer-aided underground mine planning package that integrates geological modeling, engineering design and planning"

Jan 1, 1986

By Robert B. Parsons

"This month, Tax Notes focuses on two features which can potentially ""dress up"" a new issue of common shares to make the shares more attractive to investors. Attaching warrants to a share issue is a relatively common practice, and recent years have seen an imaginative variety of different kinds of warrants, some of which can be subject to somewhat different tax treatment . A less common financing strategy which certainly deserves some consideration involves the possibility of utilizing ""Share Purchase Tax Credits "" in conjunction with a new share issue.IntroductionPrevious subjects covered in Tax Notes have dealt with flow-through shares and other tax angles which can make equity issues more appealing to potential investor s. Two other techniques which can add zest to a new stock issue involve the utilization of warrants and ""share purchase tax credits"" (or SPTCs). This article takes a brief look at the better known subject of warrants and the lesser known matter of SPTCs.Of course, this paper presents only a relatively general summary of the income tax implications of warrants and SPTCs, and is not intended to be a definitive commentary on all of the detailed and complex tax issues that might be relevant in the circumstances."

Jan 1, 1985

By P. A. Verhey

"This paper describes a series of wear-resistant ceramic materials which have been successfully used in the mineral processing industry in Canada. Applications include use with metallic ores, coal, potash and asbestos, and in other processes where wear degradation is of major concern. The paper will also deal with considerations involving the selection of the different ceramic materials available. It will cover the installation of ceramic materials on support structures under varying process ' conditions, as well as the other physical and chemical factors which have to be taken into account.IntroductionIn the mineral processing industry, large volumes of ores tailings and other materials are handled. The abrasive nature of most of these materials results in extensive wear to both handling and processing equipment.Wear ratios versus cost, production losses due to down time and wear-resistant material suitability for a given application all demand particular attention when viewed against the need for increased efficiencies in existing processes. As a consequence, a very active continuous search for materials with improved wear resistance has been carried out for many years.In this search, starting about 20 years ago, dense ceramic materials were tested and evaluated in certain applications, notably in the iron ore and asbestos operations in Eastern Canada. As a result of substantially better performance both in continuous extended life and ultimate economics realized , wear-resistant ceramic applications developed progressively in many other processing applications, replacing traditionally used materials.In the vast majority of wear-resistant ceramic applications, considerable extended life over previously used materials was established. This invariably was not just a fractional increase but, in most cases , in factors of double, triple and often all the way up to 18 and 20 times the life of alternative materials used previously. In certain applications, extended life could not be measured and appears to be indefinite.Obviously, as a result of such experiences, the progressively wider use of wear-resistant ceramic materials is now an established trend."

Jan 1, 1981

By K. T. Aye

An investigation into the leaching of chalcocite and covellite in cyanide solutions at concentrations typically encountered daring gold cyanidation has been conducted. The results indicate that, for both minerals, the extent of leaching is greater under anoxic conditions, but is still incomplete even in the presence of free cyanide ions, with undissolved copper solids remaining in equilibrium with solution species. The speciation of the sulfur and cyanide reaction products in solution are interpreted in terms of the fast formation of a copper(I)- cyanide complexes in solution and a sulfur-rich copper(I) polysulfide solid phase, which then reacts more slowly to produce thiocyanate ions.

Jan 1, 2011

By A. L. Mular

"IntroductionSince the mid -1960s, automatic control of grinding circuits has become the rule, to avoid losses attributable to frequent circuit upsets associated with uncontrolled disturbances such as ore hardness variations. Higher capital costs of grinding equipment and corresponding operating costs-especially with respect to energy consumption-are major factors that continue to stimulate interest in grinding control.Grinding circuit control strategies depend upon the control objectives defined by the processing plant and are subject to constraints such as: maintain final per cent solids within some range, do not transport steel ball s out of the discharge trunnion, or do not overflow or empty the pump box and so on. Constraints depend on the nature of equipment employed within the grinding circuit and may actually determine the characteristics of the control scheme. Typical control objectives are:1. Maintain final particle size at set point by ,a. manipulation of fresh feed rate with circulating load maintained by manipulation of pump box water addition rate, orb. manipulation of pump box water addition rate with circulating load maintained by manipulation of fresh feed rate, where the methodology utilized to accomplish either (a) or (b) is dependent upon equipment/circuit constraints such as the availability of a variable speed pump.2. Maintain circuit throughput at a maximum by,a. manipulation of fresh feed rate subject to constraints on final particle size and variables such as power draw, circulating load and mill overload.3. Maintain mill load at set point by a. manipulation of fresh feed rate subject to constraints such as on power draw.4. Maintain mill power draw at set point bya . manipulation of fresh feed rate subject to mill load constraints. Often, a grinding control objective is dictated by the recovery vs fineness-of-grind characteristic that exists for downstream separation circuits. When recovery is relatively insensitive to size, maximum throughput in the grinding circuit is advantageous.The purpose of this paper is to review control strategies for primary ball mill grinding circuits, rod mill/ball mill grinding circuits and semi-autogenous grinding mill circuits. Primary sensors employed are highlighted and modern trends are documented briefly."

Jan 1, 1989

By T. A. Apelt, B. J. Elliot

"In September 1993, the flash furnace at Kalgoorlie Nickel Smelter, KNS, was brought off line after almost 12 years of operation. This is a record campaign life for a flash furnace. The furnace was' totally rebuilt and the capacity of the plant increased from 540 000 tpo to 750 000 tpa of concentrate throughput. The throughput increase was' achieved through the construction of a 525 t/day oxygen plant and upgrading of various plant ancillaries. A number of significant design modifications were also built into the flash furnace and oxygen enrichment was implemented in the operation of the Peirce-Smith converters.This paper discusses the rebuilding of the flash furnace and design modifications made to furnace equipment and ancillary plant. Some preliminary post-startup operating data are presented.IntroductionIn September 1993, Campaign 6 of the flash furnace was concluded and the furnace brought off line for rebuilding. The campaign length was almost 12 years and set a new record for campaign length. Planning for the rebuild took place over the last five years of the campaign. A number of modifications to the design of the furnace and the ancillary plant were planned to coincide with the furnace rebuild. The furnace was rebuilt and recommissioned in 70 days. The increased plant capacity of 750000 tpa has been achieved by the construction of a 525 t/day oxygen plant and modifications made to ancillary plant which centred around increased p~ control, efficiency and hygiene. This paper examines the development and implementation of the modifications made to the furnace and ancillary plant. Preliminary post-shutdown performance data are presented."

Jan 1, 1995

By Stanley G. Butcher

Predictions of coal cleaning plant performance from the washability data are traditionally used at the conceptual design stage of a coal preparation plant to confirm process selection. The development of computer programs which simulate the operation of a plant facilitates the optimization of product yield and quality, and ultimately proceeds. It is shown that the optimum is sensitive to changes in mine operations and market price structure. A computerized review of operations is thus recommended as an on-going activity .

Jan 1, 1979

By R. S. Nichols

"During 1973 to 1978, Canadaka Mines Limited, a subsidiary of St. Joseph Explorations Ltd., undertook an extensive exploration and development program in the Cobalt area. This program resulted in the delineation of previously unknown stratigraphic units in the Archean volcanic sequence. During this time period, significant are controls related to area silver deposits were also identified.The Archean geology is comprised of a volcanic pile conformably overlain by sediments. The volcanics contain at least two felsic volcanic centres near the stratigraphic top of the pile. The bulk of the pile consists of mafic flows and interflow sediments. lnterflow sediments around silver are shoots contain mineralized halos of base metal sulphides. The halos exhibit lateral and vertical metal zoning with Cu, Pb and Zn mineralization decreasing away from an are shoot.Silver mineralization controls determined during the Canadaka program agree with the historically well established importance of Coleman sediments as well as Archean contacts for hosting silver deposits. The vertical extent of are shoots is typically 150to 250ft. A strong correlation was found to exist in the Cobalt area between Archean strike and the strike of are veins. Finally, al/ Cobalt area are deposits appear to be associated with a distinct volcanic pile at the top of a sequence of Archean flows."

Jan 1, 1988

By Mark Stephenson, Paul Henharen

"The objective in the mineral processing of primary ores is to liberate and effectively recover each individual economically viable diamond with minimal reduction in its potential value.There are three distinctive phases in diamond processing:Feed PreparationWhere the diamonds are liberated and waste material finer than the economically selected cut-off size is rejected. In this section we will discuss the various techniques utilised worldwide to effect feed preparation.Primary ProcessingWhere the diamonds are recovered into a high grade concentrate suitable for the more expensive and selective final recovery process. In this section we will discuss the development of primary processing from jigs and pans to the more current techniques utilised worldwide.Final RecoveryWhere there is selective rejection of waste particles until only diamonds remain. The diamonds may then be acidised prior to packing and marketing.Within these distinct phases a variety of unit processes have been utilised and this paper will discuss their relative merits, limitations and suitability in respect to the various stages of diamond project development from prospecting through to production.Basic capital and operating costs are compared for the autogenous milling route developed in the CIS and the crushing and scrubbing route utilised in the west."

Jan 1, 1994

By D. Bois, F. P. Hassani, M. Hossein

"A growing environmental awareness hos prompted the mineral industry to seek innovations in waste management and technology. It is estimated that over 500 million metric tonnes of solid waste each year are rejected by the Canadian mineral industry. This waste hos to be disposed of in the most environmentally and economically acceptable manner.An extensive study has been conducted to estimate the cost of implementing total tailings fill from a waste disposal point-of-view as an alternative to large-scale surface disposal of tailings. The cost of waste disposal at the surface (tailings pond), and underground (total tailings fill) for three Canadian mines which have taken part in Quebec Mine Survey conducted in 1992 are analyzed. Surface disposal is the most economical and common method of mine waste disposal in Canada. Total tailings backfill as a method of waste disposal is technically feasible but cannot be regarded as more economic than surface disposal in all . It is important to remember that while surface disposal costs are rising, due to tighter legislation and more environmental pressure on governments; the costs of preparing and placing total tailings backfill is still falling as the technology improves."

Jan 1, 1994