Search Documents

By Sammy Bansah, Komla Dzigbodi-Adjimah

Ghana, a major West African gold-producing country, took a crucial step in 1986 to allow private participation in mining ventures that had hitherto been state controlled and starved of funds. This decision has led to a three-fold rise in gold production with substantial local and foreign capital once again flowing into exploration and mining projects. Though the rise in gold export is due primarily to increased production from large mines such as Ashanti Goldfields Corporation, Billiton Bogosu Gold, Tebrebie Goldfields and Ghana Australia Gold that work primary lode gold deposits on quartz veins and Banket conglomerates, a fair amount of gold comes from placer gold mining from which two new mines have been developed at Kwabeng and Bonte during the current gold boom. Also, placer gold mining is important locally because the lower capital outlay required for its development enables many entrepreneurs to operate small concessions and provide employment for a large pool of unskilled labor. Placer gold exploration and development in Ghana is labor-intensive. Pitting is the most used method although few employ the mechanized (“Banka”) drilling. The advantages and disadvantages of the two approaches in the local setting are discussed. The gravel is normally sluiced and the gold recovered by amalgamation. The drawbacks to successful placer gold exploration in Ghana have been attributed to lapses in execution of exploration programs (Dzigbodi-Adjimah and Arhin, 1993; Dzigbodi-Adjimah and Gawu, 1994). However, the failure to recognize and set time frameworks and financial limitations for the various stages of placer gold exploration have spelt the doom of some projects. It is critical that the characteristics of the placer gold deposit be determined by efficient and cost effective means. A planned exploration supported by adequate flow of funds saves costs and leads to success. This article discusses the current Ghanaian situation and presents proposals from case studies for planning and budgeting placer gold exploration pro-grams for use in similar settings.

Jan 1, 1995

By Samantha A. Beeson, Colin Poole

"A selective flocculation-floe flotation technique is already in use in the Canadian potash industry for the removal of water-insoluble slimes, but the process is currently limited in its application and reagent consumption is high. The work described in this paper details investigations into the separation of sylvite and halite from water-insoluble slimes by selective flocculation utilising other commercially available polymers.Preliminary flocculation performance tests were undertaken on pure sylvite, halite and water-insoluble minerals to establish the importance of a number of experimental parameters. The data from these single mineral tests was then used to establish optimum parameters for the separation of sylvite and halite from a synthetic mixture similar in composition to a typical potash ore. Under optimum conditions, separation was achieved with high recoveries using dispersant and flocculant dosages significantly lower than those currently used in plant practice.IntroductionAlthough solar evaporation and solution mining are used in some operations, most potash is extracted by conventional underground techniques and is then processed by froth flotation, in order to separate the valuable sylvite (KCI) from halite (NaCl) and water-insoluble gangue minerals. Flotation is usually preceded by a desliming stage to remove water-insoluble fines, but this also results in high potash losses and affects process brine requirements. To overcome these problems, one plant operated by Cominco in Saskatchewan uses a selective flocculation -floe flotation process (Banks, 1979/1980), in which a polyacrylamide flocculant is added to produce floes of water-insoluble material with minimal incorporation of halides. A collector is then added to render the floes hydrophobic and suitable for removal by froth flotation.A number of workers have also investigated the use of selective flocculation in potash processing, but these too have been concerned with developments in the removal of water-insoluble slimes (Williams, 1960; Brogiotti et al, 1974; Chan et al, 1986; Thompson et al, 1979; etc.). This paper provides results of novel investigations into the selective flocculation of sylvite and halite from water-insoluble minerals and discusses the possible mechanisms involved."

Jan 1, 1995

By Philippe Monier, Frank C. Basham

"This paper outlines the scope and applications of 'COALMOD', the British Columbia Ministry of Energy, Mines and Petroleum Resources' computerized financial simulation model for coal mining developments. After a description of the computer system and language of implementation, the logic and scope of current model sub-routines are presented. This is followed by a presentation of examples on the current applications of the model to public policy evaluation, including benefit-cost analysis, fiscal analysis and evaluation of the effects of public infrastructure investments made in support of mining projects.IntroductionThis presentation has been developed in response to a number of requests from coal mining companies and various public agencies who have indicated interest in understanding our application of contemporary analytical techniques to public policy in the coal sector. In particular, the subject of this paper is an explanation of COALMOD. a mnemonic given to a computerized, mine-specific, financial simulation model which is assisting the Government of British Columbia in evaluations of new coal projects, assessment of public sector investments made in support of these projects and. more generally, measurement of the financial effects of current or proposed government policies, and factors outside immediate government control such as coal prices and transportation costs."

Jan 1, 1981

By Ludwig Strah

"The paper outlines the history of rubber mill liners beginning with the awarding of the first North American patent rights in 1923. It includes the early-day applications and installations of the 1920s and 1930s through to their present-day application. Over-all rubber mill liner design is discussed in relation to present day installations employing rubber mill liners in various grinding applications. A brief overview is given of a manufacturer's procedures to produce rubber mill liners.IntroductionIn early 1910, it became apparent that the productive life of the silver mines in Cobalt, Ontario, could be substantially prolonged by mining lower-grade ores.The mining of lower-grade ores required the establishment of treatment facilities which initially employed jaw crushers, stamp mills, jigs and concentrating tables. The recovery of silver in other than a coarse metallic form required the additional step which was introduced at that time: the cyanidation of silver concentrates from the tables. The resultant requirement for increased and improved recovery led to the introduction of grinding mills, i.e. tube mills.Shortly after the introduction of the tube mills to the Nipissing Mine's mill in 1914, the idea of using rubber as a mill liner material was spawned. However, no action was taken due to the advent of World War I. It is interesting to note that the idea of rubber mill liners emanated from having used pieces of solid rubber tire as an emergency repair on a set of liners when a liner had broken and no immediately available spare was on site.The credit for this ingenuity and subsequent application for a patent on rubber mill liners falls to James John Denny, the mill superintendent, and Rolla Barnum Watson, the general manager of Coniagas Mines Limited. The patent application was formally made on December 3, 1921. The U.S. Patent Office issued Patent No. 1,470,597 on October 16, 1923."

Jan 1, 1982

By Maria Skyllas-Kazacos

The All-Vanadium Redox Flow Battery that was pioneered and has been developed at the University of New South Wales (UNSW) in Sydney since the mid-1980s is currently regarded as one of the most attractive energy storage systems for large-scale implementation in a wide range of grid-connected and offgrid applications. Several companies are now manufacturing and installing MW-scale VFBs in applications ranging from renewable energy storage, load-levelling, emergency back-up power and power arbitrage. The full-scale uptake of the VRB in commercial energy storage systems however, is heavily dependent on the availability and cost of vanadium used in the VRB electrolyte. Cost is also a function of purity requirements and although there is little scientific evidence on the effect of impurities on the VRB life and performance, VRB developers continue to demand high purity vanadium at considerable cost. This paper will provide a brief overview of the current understanding of electrolyte impurities on VRB performance together with an economic analysis of the impact of vanadium prices on overall VRB capital and levelised costs for a range of applications.

Jan 1, 2014

By K. R. Wood, G. W. McDonald

"The tailings disposal system at Les Mines Selbaie includes dewatering of tailings in a high-capacity thickener, followed by point discharge of the thickened solids to form a stable conical pile. Tailings water drains to ponds formed behind engineered dams, prior to either recycling f or process use or discharge to the environment. Design and economic considerations of the system are discussed. Construction, start-up and operating experiences are also presented.Introduction Les Mines Selbaie is located in the Abitibi region of northwestern Quebec, approximately 700 km north of Toronto and 150km south of James Bay. More locally, the Detour gold mine is 60 km to the west while the Noranda smelter is 220 km to the south.The deposit was discovered as a result of a Questor INPUT Mark VI geophysical survey in 1973, followed by diamond drill programs from 1974 to 1976. Three mineralized zones were delineated and underground exploration was carried out on all three. A production decision for the 'B-zone' copper-gold-silver orebody was made in July 1979. The underground operation started in July 1981, with full production of 1500 t/d being achieved in May 1982.During the planning phase, every effort was made to ensure that the operation would be environmentally sound . The design included the provisions of the then newly proposed provincial environmental guidelines. The tailings disposal system formed the most significant part of the environmental program due to the large volumes of solids and water effluent. In addition, the design allowed for future expansion of the system to accommodate mining of the other zones, thus minimizing future costs and disruptions."

Jan 1, 1986

By F. W. Crossland

Losses of metal are often traced to incorrect pH/ORP signals in flotation, leaching, extraction, electrolysis, and precipitation processes, aggravated by pressure changes. IC Controls, a Canadian mining sensor manufacturer, developed a new superior pH/ORP sensor that stops metal losses, reduces environmental footprint and contributes to sustainability. The cause of incorrect pH/ORP signal is rooted in the reference. Reference junctions are designed to allow diffusion of reference chloride ions into the process but also allow process ions to diffuse into the reference. This development is important to mines and hydrometallurgists where sulphide, cyanide, ammonia and other poisoning ions are present in the process. These ions react with reference electrolyte components causing the signal to change, drifting from the correct process value. With fluctuating process pressure, ion in migration dilutes the electrolyte producing similar signal drifts. If process ion in-diffusion could be stopped, the pH/ORP signal would be accurate. IC Controls new pH/ORP sensor stops process ion in-diffusion, and remains accurate over long periods. New processes using higher pressure and fluctuating pressurized reactors will greatly benefit from stable pH readings. Similar to IC Controls' proven model 642 Mining pH sensor, our new model 647 contributes to sustainability through reducing disposal costs from waste reagents, lost metal and fewer used sensors.

Jan 1, 2014

By Julia Pflieger, Manfred Russ, Johannes Gediga

This paper shall show an economic feasible approach to implement Greenhouse Gas (GHG) reduction measures into the mining and metallurgy industry. The goal to improve energy consumption is directly linked to the reduction of GHG emissions and therefore directly in correlation with the economic viability. A baseline scenario of the considered reference system and of the respective reference year has to be defined, mapped and analysed. In a second step an analysis of the same operation using available and prospected Best Available Technology (BAT) processes is carried out to generate a basis for a benchmark system. The identified reduction potentials are reported and the GHG emission reductions are put into relation to the investment cost of the new process technologies / process adaption to be implemented. This economic feasibility calculation is necessary to realise a cost efficient GHG reduction roadmap implementation into the company's business operations. The GHG reduction roadmap is developed using ratios between GHG reduction and investment / operating cost to get an indication for a sequence for implementing carbon emission reductions measures.

Jan 1, 2010

By K. Sawada

Along with the expanding demand of copper concentrate in Asian countries, custom-smelters have confronted with difficulties of low TC/RC. Now, Japanese Copper Industry have 2 options; investment in mine development and/or recycling of copper scraps. The strategy of global mining companies is analyzed, and implications for Japanese Copper Industry will be discussed from the viewpoint of sustainability of smelters in Japan.

Jan 1, 2014

By Alan B. Morrow, William A. Poe

"Minerals processing operations are constantly challenged with improving production rates, yields, energy efficiency and process stability. Advanced Process Control has proven to be an effective tool for improving operations by capturing the full process capabilities consistently. However, the velocity of applying the technology as well as the sustainment of these significant benefits has been hampered by the usability of the software and adaptability of the applications.Some of the new technology developments that improve the usability and adaptability of advanced process control include:• modern and intuitive user interfaces,• customizable models to support unique process behavior,• fast and flexible OPC connection tools,• automated model building,• integration with first principles dynamic models and• improved performance monitoring.This paper will briefly discuss the new technology developments that have improved the usability and adaptability of advanced process control and how this can affect minerals processing operations.In today’s environment, Minerals Processing plant managers continuously face new challenges and requirements including:• higher energy efficiency,• increased run lengths,• reduced product quality variability,• reduced emissions,• higher availability, and• lower operating costsOperating a unit to meet these challenges in real time is not easy for operators and conventional process control systems. However, innovatively using existing technologies in Minerals Processing plants can improve operations on a minute by minute basis and reap significant benefits.Advanced Process Control (APC) can extract the maximum performance benefits from existing equipment while respecting plant operating constraints. Expensive capital projects to upgrade equipment are not always necessary. Advanced Process Control can deliver significant economic benefits by maintaining the plant at its most profitable point as conditions change."

Jan 1, 2016

By J. Etcheverry, E. Seguel, R. Díaz, F. Parada, R. Parra, E. Balladares

A thermodynamic and kinetic model is proposed to explain the formation of bornite, chalcopyrite and magnetite during partial roasting of enargite-containing copper concentrates. The proposed mechanism involves solid-solid-gas and solid-gas reactions between chalcocite, pyrrhotite, gaseous sulfur and oxygen. The formation of bornite could be explained by a two-step reaction: the first one involving the formation of chalcopyrite by a reaction between Cu2S, FeS and gaseous sulfur, followed by a second step in which the newly formed chalcopyrite reacts with additional chalcocite to form bornite. Although thermodynamically the direct formation of bornite is more favorable than that of chalcopyrite, the lower diffusion kinetics of bornite formation could explain the preferential formation of chalcopyrite. If the reaction occurs with stoichiometric chalcocite and pyrrhotite in the presence of gaseous sulfur to form chalcopyrite, no bornite is formed, while for the stoichiometric reaction between chalcopyrite and chalcocite in the absence of sulfur, only bornite is formed. For the formation of magnetite and chalcopyrite the mechanism could involve the partial reaction of chalcocite and pyrrhotite in the presence of oxygen. The proposed model is thermodynamically consistent with the experimental results obtained in laboratory and pilot plant. INTRODUCTION The processing of high-arsenic copper concentrates with over 0.7 wt.-% arsenic by conventional smelting-converting normally require an additional arsenic removal step to reduce arsenic content to levels below 0.2–0.3%. One of these high-arsenic copper concentrates is the one produced by the Ministro Hales Division (DMH) of CODELCO, which has the typical chemical composition shown in Table 1. Enargite (Cu3AsS4), chalcocite (Cu2S) and pyrite (FeS2) are the main mineralogical species present in these concentrates, with over 75 wt.-%, as shown in Table 2. Partial or “neutral” roasting of these concentrates under controlled temperature and partial oxygen pressure conditions at 923–993K (650–720ºC) can remove up to 95% of the arsenic as As2S3 (As4S6), which has a high vapor pressure under these conditions, leaving a calcine with low residual arsenic. In copper concentrates, arsenic is present generally as enargite and arsenopyrite. This compounds as well as others such as pyrite and covelite, decompose readily above 770 K (500ºC), releasing, in addition to gaseous arsenic trisulfide, gaseous sulfur which by oxidizing to SO2 generates most of the heat required by the process.

Jan 1, 2019

By S. Bantubani, I. Mc Dougall, S. Arjun, H. Joubert, R. Hansraj

The requirements determining the design of the Söderberg electrode columns used in base metal applications are different to those of other industries. There is a strong trend to position the contact shoes above the furnace roof in order to reduce the risk of water leakages directly onto the furnace bath. Tenova Pyromet has adapted its proven electrode column design for application on base metal electric furnaces based on these requirements. The design modifications implemented as well as considerations regarding the overall electrode-roof-furnace arrangement are discussed. Equally important is the management of the Söderberg electrodes to prevent over or under baking. Tenova Pyromet has developed the AutoFurn™ furnace controller to not only optimise furnace operations, but to improve electrode management. An overview of the electrode management control philosophy implemented by AutoFurn™ is provided, focusing on intelligent electrode regulation, slipping and baking. INTRODUCTION Tenova Pyromet has developed an electrode system for use in base metal furnaces, which builds on the experience that Tenova has gained during the past 30 years with electrodes in the ferroalloy and base metals industries. In base metals applications, an important safety consideration is the minimization of water within the furnace and on the furnace roof. In addition, direct contact between copper equipment such as contact shoes and pressure rings and the contents of the furnace is discouraged. In a 3 phase AC furnace, three electrode columns transfer the electrical energy to the furnace bath. Both Söderberg and prebaked carbon or UHP graphite electrodes are in use in base metal furnaces. In each column, the electrode is held in position by a hydraulic slipping and regulating device, a pressure ring and contact shoes. The electrodes can operate in a submerged-arc or brush-arc configuration, where the electrode is immersed in the slag or a short distance above the slag (Mc Dougall 2013). The electrode equipment is divided into an upper and a lower electrode assembly. The self-baking Söderberg electrode is made from lengths of steel casings that are added to the top of the electrode column and welded into place. Carbon electrode paste is added to the inside of these casings and is baked to form a solid tip in the region of the contact shoes. The working platform that surrounds the area where new electrode casings are added, is electrically isolated from the building and each electrode is isolated from the others to ensure the safety of the personnel who perform the electrode casing additions.

Jan 1, 2019

By Esa Peuraniemi, Hanna-Leena Heikkilä

Boliden Harjavalta has been operating a copper flash smelter since 1949. Thus, in 2019, the smelter is celebrating its 70th anniversary of flash smelting. Slag formation is an integral part of the smelting process; currently the processing of slag is based on froth flotation at the slag concentrator. It provides high recovery of copper but restricts slag utilization; the final copper slag is deposited in a landfill. The Harjavalta smelter commissioned a new landfill area for final slag in May 2018. This paper describes the full project from permitting to commissioning of a new landfill area. The permitting process is described comprehensively, including environmental impact assessment together with the environmental and dam safety monitoring. During the environmental impact assessment, observations on rare animals protected on European level were made as well as archaeological findings. Successful completion of the permitting allowed the construction phase to start on time. After six years of intensive work, the new landfill was commissioned in May 2018. The new landfill area provides a sustainable way to store the smelter’s slag for decades to come. INTRODUCTION Slag processing Sulphide based concentrates have always formed the main raw material stream at Harjavalta’s copper smelter. During the smelting and converting steps, the iron included in the concentrate is oxidized and fluxed using a silica-based sand. Originally, the slag was processed by using an electric slag cleaning furnace after which the final slag was water granulated. Froth flotation has been utilized for slag treatment since 1966. In the beginning, the slag was cooled in open ditches. In 1984, controlled slow cooling of slag was licenced to enhance copper recovery at the flotation plant. Today, the slag from both the smelting and converting is tapped/skimmed to slag ladles and treated in the following steps: Slag ladle transportation from the smelter to the cooling area by slag hauler Slow cooling of slag in the ladle to allow mineral precipitation Unloading the slag by tilting the ladle; causing the slag to crush as it drops from the ladle Feeding the crushed slag (-500 mm) by wheel loader to a slag concentrator’s feed funnel followed by a conveyor belt transporting the slag to the concentrator plant Crushing and grinding using lump and pebble mills Froth flotation of the valuables Recycling the slag concentrate back to the smelter feed after dewatering Pumping the final copper slag to the landfill area.

Jan 1, 2019

By R. A. Nemchek

Over the years, concentrator plant design has evolved from a large number of small grinding mills to a small number of large mills. In many cases, all of the tonnage runs through a single mill (typically a large SAG mill), so that the plant’s performance hinges on the productivity of this one machine. Industry specifications attempt to address the critical nature of today’s grinding mills in a manner that is often overly complex, neglects economics, and is not clearly focused on the end user’s goals. This paper surveys current industry practices, and proposes an improved approach to standards writing recognizing that product design, procurement, manufacturing, and quality are all inter-related in contributing to a project’s success. The lessons learned here can be extended to specifications for all types of machinery.

Jan 1, 2012

By H. Dundar

The first application of High Pressure Grinding Rolls was in 1985 at a cement plant, for the purpose of capacity improvement. Then various circuit configurations were derived to achieve a reduction in overall specific energy consumption, by transferring more of the grinding required to the HPGR. In most circuit configurations, the recycle of fines is required for effective breakage between the rollers. By increasing the fines amount in the feed material to a specific level within the recycling load, a uniform material bed is created and a higher pressure gradient along the roller width is obtained, resulting in compact flakes, including more fines. The fines recycle results in enhancement of the interparticle breakage. This paper will discuss the effect of the feed size distribution on HPGR performance.

Jan 1, 2012

By R. Saulters, M. Garshasb

The Transportable Moisture Limit (TML) is the copper concentrate moisture content beyond which liquefaction may occur during shipping. This study indicates that TML is a function of mineralogical characteristics of concentrate, which in turn may directly affect moisture retention properties. A comprehensive mineralogical and chemical analysis was conducted to determine the impact of composition and mineral content on concentrate’s TML. The analysis indicates that the high TML value is associated with particular minerals such as gypsum, swelling clay, muscovite and pyrite. Since higher TML values allow higher moisture contents for shipping, this property is desirable for concentrate inventory management and shipping flexibility. Scarcity of minerals that may increase TML contributes to limitations of shippable inventory. INTRODUCTION TML is the maximum moisture content of copper concentrate beyond which liquefaction may occur. Moisture content above the TML is considered a shipping hazard as it may result in loss of lives and cargo. The details of TML testing are given in ISO 12742:2007 (ISO 12742). In principle, TML is 90% of the Flow Moisture Point. The method of testing for Flow Moisture Point and TML is based on procedures that provide pulsations that simulate the cyclic force of ocean waves to determine moisture levels at which the onset of concentrate flow may occur. International Maritime Organization (IMO) provides guidelines for developing and approving TML testing and moisture determination in the context of its Moisture Management Plan (MMP) for shipment of copper concentrate cargoes (IMO 2013). The IMO regulations are specifically provided in MSC.1/Circ. 1454 “Guidelines for developing and approving procedures for sampling, testing and controlling the moisture content for solid bulk cargoes which may liquefy”. Since each port has its own operational characteristics, resource availability, peculiarities of governmental structure, and desired methods of interaction with the authorities, it is necessary to adopt the IMO guidelines to the local requirements. In order to establish a TML and MMP measurement system, it is required to implement and follow proper guidelines for the relevant procedures. For example, sampling procedures are developed in accordance of ISO 12743, “Copper, lead, zinc, and nickel concentrates – Sampling procedures for determination of metal and moisture content”. Moisture content of copper concentrate samples are determined in accordance with ISO 10251, “Copper, lead, zinc, and nickel concentrates – Determination of mass loss of bulk material on drying”. To assure strict adherence to the MMP procedures, the overall system needs to be integrated into the site QA/QC system, which would make them auditable and certified in accordance with standards such as ISO 9001, ISO 17025, and ISO 17020.

Jan 1, 2019

By Xiaolin Cheng, A. J. Sinclair

"Abstract - Norm calculation procedures originally designed principally for igneous rocks are very rigid in their application and, in general, do not utilize important alteration minerals. For instance, volatile components are essential constituents of many metasomatic rocks but either are not used or are not used effectively in determining normative minerals by the CIPW norm or Niggli-Barth norm procedures. Our approach to determining norms for metasomatic rocks allots all major, minor and volatile constituents to a set of standard normative minerals which are commonly observed as products of hydrothermal alteration. A useful procedure is to have a metasomatic norm approximate the mode as closely as possible. Petrographic information helps to provide the necessary mineralogical constraints. With the recognition of an immobile component and knowledge of sampling and analytical errors in lithogeochemical data, it is possible to recast norms into amounts of alteration minerals relative to a given amount (100 grams) of parent rock. Combining these results with the calculations of absolute loss or gain of individual chemical constituents and considering errors (e) for an appropriate confidence level, an overall (net) material exchange equation can be presented as follows:SMineralparent rock ± e + SConstituentgained from solution ± e= SMineralaltered rock ± e + SConstituentlost from wall-rock ± ewhere all items have extensive units (e.g., grams). The model includes the initial and final mineralogy of rocks (evident in the field) as well as gains and losses of specific elements. Only those constituents whose calculated losses and gains are significantly different from zero are retained in the above model, and only the normative minerals with abundances significantly different from zero are included in the model (equation). One advantage of the chemicomineralogic model is that parent rock and product are modeled in mineralogical terms that are familiar to and easily usable by exploration geologists."

Jan 1, 1995

By Y. A. Grinin, M. A. Liamina, V. A. Shumskij, Y. I. Sannikov, M. V. Radashin

"A brief history of the development of the Kivcet flash smelting process is presented. The broad scope of the process with an ability to treat high grade lead sulphide concentrates, as well as oxidized lead-zinc residues, is emphasized. Fine coal in the charge serves two purposes, one as auxiliary fuel and the other as a pre-reductant for ferric iron in residues. Current Kivcet operations incorporate a layer of coke or “coke checker” at the surface of the slag in the reaction shaft that acts as a reducing agent for flame products or slag that flow through it. Details of this invention, are given. IntroductionFor many years, the sinter-blast furnace lead smelting process has been the main internationally accepted method used for the production of primary lead metal. In recent times, this process has been unable to meet legislated environmental restrictions and it became clear in the mid-1960s that a new and cleaner process would have to be developed. The present level of Kivcet performance was developed in three main stages:1. flash smelting natural sulphide lead raw materials with the attached electric furnace for production of lead bullion and crude zinc;2. natural raw material smelting with lead and zinc separation in a “coke filter” or “coke checker” at the surface of the slag in the reaction shaft to produce lead bullion and ZnO-bearing slag that can be fed to conventional slag fuming; and3. processing of oxidized lead-bearing raw materials, such as low grade zinc plant residues, with the production of lead bullion and ZnO-bearing slag periodically directed to slag fuming."

Jan 1, 1998

By J. Seidel

In 2009 Newmont Mining Corporation’s annual global spend on grinding media reached $94M USD, having doubled in the five years since 2004. The major contributing factor to the spend escalation during this period was unit consumable price, with total media consumption also rising as a function of annual ore tonnes milled. In an effort to better understand and manage the growth of this expenditure a significant supply chain management program was implemented. This was complemented by a series of technical initiatives focussed on grinding media specifications, quality management and the prediction of grinding media wear rate as a function of physical ore characteristics. This paper discusses the methodology and outcomes of these activities.

Jan 1, 2012

By J. Seidel

In 2009 Newmont Mining Corporation’s annual global spend on grinding media reached $94M USD, having doubled in the five years since 2004. The major contributing factor to the spend escalation during this period was unit consumable price, with total media consumption also rising as a function of annual ore tonnes milled. In an effort to better understand and manage the growth of this expenditure a significant supply chain management program was implemented. This was complemented by a series of technical initiatives focussed on grinding media specifications, quality management and the prediction of grinding media wear rate as a function of physical ore characteristics. This paper discusses the methodology and outcomes of these activities.

Jan 1, 2012