Search Documents

By Holly L. O. Huyck

Disseminated hypogene sulphide mineralization in the Lakeshore porphyry copper deposit (also called the Cyprus-Casa Grande deposit) of Arizona occurs in both a granodiorite stock and associated volcanic rocks. Structural development and vein paragenesis at Lakeshore are similar to other Laramide porphyry copper deposits of the southwestern U.S. Two major structural trends are present: intrusive contacts, copper-bearing potassic alteration veins and major post-mineralization Basin-and-Range type faults trend N-NW, whereas phyllic veins and secondary post-mineralization faults trend N-NE, and deep propylitic veins trend NE-ENE. Lithologic permeabilities, caused by fracturing in all rocks and by grain size distributions in volcanic rocks, controlled the distribution of copper mineralization. Differences in chemical compositions of host rocks did not affect are grade. Structural control, through density of chalcopyrite-rich veins, was the major control of are grade. Fracture density of other potassic vein types did not strongly affect grade. Within volcanic lithologies, permeability, as indicated by grain size distribution, provided a second-order, but significant, control of mineralization.

Jan 1, 1990

By Y. Thibault, G. Deschênes

An open-pit mine, located in Mexico, processes an ore a rate of 4000 tpd, using conventional cyanidation and AYR. A laboratory study was conducted to increase silver extraction and to reduce the concentration of cyanide in leaching. The sample contained 0.41 g/t Au, 125 g/t Ag, 99% gangue minerals, 0.7% pyrite, 0.07% sphalerite, 0.03% chalcocite. Silver was present as acanthite, stromeyerite, silver mercury/halogen, silver with copper in solid solution and jalpaite. The plant conditions (2400 ppm NaCN) produced 90.2% gold extraction (residue at 0.04 g/t Au) and 92.7% silver extraction (leach residue at 9.1 g/t Ag). The CELP (CANMET Enhanced Leaching Process) produced 97.0% silver extraction (residue at 3.8 g/t) and 90.2% gold extraction using 500 ppm NaCN. The incremental gross revenue was estimated at $US7.6 million and the reduction of cyanide costs was $2.9 million per year (79%).

Jan 1, 2011

By A. Khodadadi, M. Abdolahi, P. Taimory

Cyanide is used by the mining and chemical industries in tremendous quantities without attention being given to its hazardous properties. The use of cyanide compounds in mining is one of the most important environmental issues for the mining industry due to the acutely toxic properties of many cyanide compounds to humans and aquatic life. Cyanide tends to react readily with most other chemical elements, producing a wide variety of toxic, cyanide-related compounds and because cyanide is carbon based an organic compound it reacts readily with other carbon-based matter, including living organisms. This research is aimed at investigating a feasible and economical technique for the removal of cyanide from tailing wastewater of Muteh gold mine. In this research, removal from Muteh factory's waste water, was achieved at Tarbiat Modares University's mineral processing laboratory through the oxidation of cyanide by calcium hypochlorite. Cyanide oxidizes and changes to cyanide (CNO-) which is 1000 times less environmentally hazards than cyanide. Cyanide titration was accomplished using Rhodanine solution and silver Nitrate. Cyanide concentration in the wastewater, was 270 mg/L. Cyanide removal was achieved at an optimum pH of 12.3. However, at higher temperatures, cyanide removal was complete at this pH level. Optimum Dosage for complete removal of cyanide using calcium hypochlorite was 1.43g/L.

Jan 1, 2005

By B. A. Kjarsgaard, C. J. Mwenifumbo

"Abstract - Natural gamma-ray measurements were made in the GSC Smeaton drillhole as part of the borehole geophysical classification of kimberlite pipe 169. In addition, forty samples of Cretaceous sediments (shales, siltstones, and sandstones) and thirty-five kimberlite samples, selected from the drill core, were analyzed for major and trace elements. These elements included potassium (K), uranium (U), and thorium (Th), which are the main naturally-occurring radioactive elements.Different phases of the kimberlite, and the Cretaceous sediments which show variations in the gamma-ray activity, can be easily delineated on the gamma-ray logs. The gamma-ray logs indicate that the radioactivity in the kimberlite derives mainly from Th, and, to a lesser extent, U. Most of the kimberlite units are enriched in Th and U relative to the Cretaceous sediments, and these radioelements are mainly hosted by accessory apatite and perovskite, and minor zircon. Potassium concentrations are low in the kimberlite. The higher K concentration in the sediments clearly distinguishes the Cretaceous sediments from the kimberlite.The U/K and Th/K ratios show important and distinct differences between the two major types of volcaniclastic kimberlite. Kimberlite lapillistones have higher U/K and Th/K ratios than the olivine crystal tuffs. Furthermore, standardized U/K and Th/K geophysical logs can be used to separate marine reworked olivine shoreface sands from other shallow marine sediments that contain kimberlitic detritus. The identification of different phases and/or stratigraphic facies of kimberlite on the basis of radioelement distributions means that gamma-ray spectrometry can assist exploration, particularly in regard to diamond grade distribution."

Jan 1, 1999

By Bern Klein, A. Tugba Cebeci, Libin Tong

"Sensor based sorting faces two main challenges related to limited capacity/throughput and the ability of sensors to accurately discriminate based on estimated grades. This paper is aimed at improving sensor discrimination. Sensors have the ability to measure more than a single response. X-ray fluorescence (XRF) can detect and provide concentration information about a range of elements. Similarly, electromagnetic sensors (EMs) can generate magnetic susceptibility and conductivity responses over a range of frequency levels. The sensors thereby provide a response signature rather than a simply a single response that is a proxy for a metal grade. Furthermore, integrating sensor responses can improve the discrimination of metal bearing rock from waste. A study was conducted on a gold ore to assess sortability using XRF and EM sensors. A multi-variable regression approach was used to develop models that included a range of responses. Correlations improved significantly when compared to single response correlations. The approach showed that both positive and negative correlations contributed to the improved correlations. Stepwise regression simplified the models and showed that 2nd order interaction effects can be important. The approach also showed that combining different responses can improve discrimination accuracy. An important outcome of the study was that an ore that had been consider not to be sortable was determined to be sortable through the application of an approach that used the sensor responses in a more intelligent manner.INTRODUCTIONMining is aimed at recovering valuable minerals from their host rocks. Many methods are used to recover valuable minerals, and finding efficient and cost-effective ways is the key in research and production. . Ore sorting technology is fitting this definition. It not only discards waste rocks away from the concentrator but also recovers metal bearing ore particles that could be lost to the waste dump. The benefits of ore sorting include increased energy efficiency and reduced water and reagent usage in the downstream operations (Bamber, 2008; Gunson, Klein, Veiga, & Dunbar, 2012; Mazhary & Klein, 2015; Robben, Wotruba, Robben, von Ketelhodt, & Kowalzcyk, 2013)."

Jan 1, 2016

By Deni Côte, Marcel Vallée

"The Guide to the Evaluation of Gold Deposits reviews the successive evaluation steps in the domains of geology, engineering, and economics. The Guide analyzes, in a systemic perspective, the sequence of exploration, development, and evaluation work required to bring a mineral deposit to production. The aim is to identify the metal/mineralization losses and ore dilution that each work step contributes to the evaluation and mining process. The procedure allows one to maximize the income and profits of a mining operation, and to reduce the risks of financial losses tied to investment decisions in the mining sector. For greater efficiency, the criteria of reserve estimation and classification should be integrated with the evaluation steps and methods. At earlier stages of deposit development, when quantitative knowledge is available mainly on the geological axis, the term ""delimited mineral deposit"" should be used. The term ""reserve"" should be used only in an operating mine or in a mining project, when information in the geological, engineering, and economic domains is adequate to ensure technical and financial feasibility. ""Reserves"" are by definition ""mining reserves"". Each category of proven/probable reserves and measured/indicated deposits should be subdivided into two classes to express better the many steps of mineral valuation. The category of ""possible reserves"" shall be replaced by that of ""inferred mineralization"". This system, derived from the Australasian Code, can easily be integrated into current practices of the exploration and mining industry within a short timeframe. The proposal to develop the use of the margins of error of the estimates at a confidence level of90% should be viewed in a longer timeframe. Establishing the precision of the mineral inventories and distinguishing between categories and classes by means of the margin of error will require more work and a longer break-in period.SOMMAIRELe ""Guide d’évaluation des gisements d'or"" analyse, dans une approche systémique, les travaux d'évaluation et de mise en valeur des gisements minéraux dans l'axe de la géologie, dans l'axée l'ingénierie et dans I ‘axe de l'économique. L’objectif est d'identifier la contribution aux pertes de métal et à la dilution du minerai des diverses étapes de l'évaluation et de l'exploitation du gisement. Ceci aid erra à maximiser les revenus et les profits, et ainsi, à réduire les risques départe financière que comportent les décisions d'investissements dans le secteur minier. Pour atteindre ces objectifs, iI est essentiel de relier les critères d'inventorie et de classification des réserves aux méthodes d'évaluation des gisements. Aux stades antérieurs du développement minéral, lorsque les connaissances quantitatives ne s'étendent qu’à l'axe géologique, le terme ""gisement délimite"" sera utilisé. Le terme ""réserve"" ne sera utilisé que dans une mine en exploitation au dans un projet minier, lorsque l'information dans les axes de la géologie, de l'ingénierie et de l'économique sera appropriée pour en garantir la faisabilité technique et économique. Chaque catégories des réserves, prouvée et probable sera subdivisée en deux classes pour mieux qualifier les niveaux d'évaluation du projet. La catégorie actuelle des réserves possibles sera remplacée par celle des ""minéralisations inférées"". Plusieurs essais démontrent que le système propose, qui s'inspire du Code australasien, peut facilement et rapidement s'intégrer dans les pratiques de l'industrie. II pourrait également contribuer à une standardisation des méthodes et des nomenclatures à l'échelle internationale. La proposition d'utiliser les marges d'erreur des estimes au niveau de confiance de90%pour caractériser les estimations se situe dans une plus longue perspective. Cette application demandera des développement méthodologiques additionnels ainsi qu'une période de rodage."

Jan 1, 1992

By A. S. H. Kabir, I-H. Jung, J. Su, S. Yue, M. Sanjari

The final mechanical properties of wrought magnesium alloys are mostly controlled by microstructure and crystallographic orientation or texture. In common magnesium alloys, grain coarsening occurs during annealing process and formation of undesirable basal texture cannot be changed markedly. The aim of this work is to investigate the effect of static precipitation on microstructure and texture evolution during annealing at 250 °C after warm rolling of Mg-Al-Sn alloy. Mg-3Al-3Sn (wt. %) alloy has been designed using thermodynamic modeling software, FactSageTM, based on forming target stable and incoherent Mg2Sn precipitate within the industrial deformation temperature range. Microstructures and precipitation were investigated by optical and scanning electron microscopes and macro-texture was measured by X-ray diffraction (XRD) techniques. It was found that static precipitates form in a large scale at the recrystallized grain boundaries and retards the grain growth during annealing. Slight weakening in basal texture was also observed during annealing.

Jan 1, 2014

By Youngjib Ham

Understanding energy performance of existing buildings is vital to increasing their efficiency and reducing the overall energy consumptions. This entails facility managers to systematically monitor building energy performance and reliably identify and analyze potential problems. Currently, infrared thermography is widely used as a primary diagnostic tool for the detection of building performance problems. Nonetheless, applications of thermal images for building inspection are mainly restricted to manual and labor-intensive identification and qualitative assessment of heating or cooling loss. Automated identification of potential problems and reliable cost analysis of the associated energy loss can help homeowners to minimize financial risk of retrofits and maximize energy savings. To that end, this paper presents a new automated method for calculating the cost of energy loss for building diagnostics. In the proposed method, first, using a hand-held thermal camera, the auditors collect digital and thermal imagery from the buildings under inspection. Then, using a recently proposed method for Energy Performance Augmented Reality (EPAR) modeling, an actual 3D spatio-thermal model is generated and superimposed with a computational fluid dynamics (CFD)-based expected energy performance model. The resulting EPAR model is placed into the method proposed in this paper for cost analysis of the energy loss. Through a new 3D thermal mesh modeling using k-d tree structure and nearest neighborhood searching, performance deviations between these models are automatically calculated. Using a temperature threshold, the areas associated with potential performance problems are detected in the EPAR model and are visualized using a metaphor based on traffic light colors. Then, the actual R-values of the detected areas are measured at the level of 3D points. Based on the measured R-values and the estimated air change rate for the detected air leaks, (1) the heat loss or gain caused either by poor insulation or air infiltration/exfiltration and (2) the associated energy costs are automatically calculated. The proposed method is validated on several locations of existing residential buildings. The preliminary results show the potential of the proposed method for minimizing the inspection time as well as the risk associated with the cost analysis of retrofitting potential building performance problems.

Aug 1, 2013

By W. Dolsak

Introduction Alternative bolting injection resin Hollow bars, rebars, and cable bolts Results from an in-house product development project Sept. 2011 to Feb. 2013 Goals Introduction of a newly developed bolting silicate injection resin as alternative to cement grout based injection systems Definition of easy-to-use pumping devices and installation accessories Accomplishment of installation trials and performance evaluation

May 1, 2013

By Z. Liang, Z. Q. Liu, X. F. Li, H. L. Zhang

"Dynamic characteristics of frozen soil is important for the safe, effective and rapid construction in cold regions and artificially frozen engineering. In this paper, dynamic characteristics of frozen clay with various low temperature and different strain rate were studied by using Split Hopkinson Pressure Bar (SHPB) test and numerical simulation test. Variation of dynamical parameters and dynamic stress-strain curves of frozen clay were obtained and analyzed. The results of these test show that: Frozen clay exhibits temperature effect and strain rate effect that the failure type tends from plastic failure to brittle failure with the increase of strain rate or decrease of temperature; Under impact loading, frozen clay exhibits three typical dynamic stress-strain curves as strain rate increases, and the maximum strain of frozen clay only linear increases with strain rate.INTRODUCTIONArtificial freezing technology has been widely used in the construction of underground engineering, such as the coal mine shaft, the deep foundation pit, the urban metro and subsea tunnel, etc. Research on dynamic mechanical behavior of artificial frozen soil will provide supports for these artificially frozen engineering (Xu et al. 1998; Ma 2009). However, the dynamic mechanical research on frozen soil is mainly carried out at low frequencies or small amplitudes of the waves, behavior of frozen soil under impact loads or high strain rate loads has not been made clear."

Jan 1, 2015

By G. Q. Liu

"The application of oxygen-enriched cyanidation to three Canadian gold ore samples has been investigated. The results showed that the use of oxygen can improve gold dissolution kinetics, reduce grinding time, and lower cyanide and lime consumptions. To obtain the same gold extraction, the required cyanide leaching time was reduced from 48 hours in slurry containing 8 ppm O2 to 12 - 24 hours in 20 ppm O2 slurry. Reagent consumptions were reduced by 23 - 37% for cyanide and by 35 - 54% for lime. There was little advantage to further increasing the dissolved oxygen to 32 ppm from 20 ppm. Gold extraction from the +200 mesh fraction improved 4 - 14% in oxygen-enriched slurry. A general kinetic model derived from the cyanidation of three ore samples can be described by the following equation: <equation>where E is the gold extraction (%) at time t (hours), EI is the ultimate gold extraction (%) , and &apos;P and k are constants depending on cyanide concentration, level of dissolved oxygen, and the characteristics of the ore samples. Comparative studies of conventional carbon adsorption and carbon adsorption in oxygen-enriched slurry have also demonstrated that oxygen enrichment resulted in more favourable conditions for gold adsorption."

Jan 1, 1995

By Paivi Suikkanen, Kari Hietala, Kaarlo Haavanlammi

"Processing of high-magnesia concentrates, the recoveries of nickel and copper, as well as those of platinum group metals (PGM’s) and cobalt are key issues of the Nickel Smelting technologies. PGMs are typically found in association with each other, but also importantly with nickel and copper. A challenge of producing saleable concentrates at acceptable recovery degrees, an increasing focus on the sustainable use of metals and recent decreases in the value of nickel has increased the interest to find a reliable route from Cu-Ni-PGM bulk concentrates to product. According to studies, most efficient process for Ni-Cu-PGM concentrates is flash smelting using DON process20 years ago, in 1995, Outokumpu commenced at Harjavalta a new Nickel Flash Smelting technology based on the Direct Outotec Nickel (DON) Smelting Process. The DON process enables production of high-grade nickel matte with low Fe-content directly in the Flash Smelting Furnace (FSF) without subsequent converting. Metal values from the smelting slag are recovered in the Electric Furnace (EF) as iron containing Ni-matte. Matte refining is based on atmospheric pre-leaching and total pressure leaching. Nickel, cobalt and iron are leached leaving a leach residue containing small amount of gangue minerals and PGM’s. Iron is removed from the leach solution in and nickel will be recovered with standard methods. Overall > 95% metal recovery can be expected with low energy consumption and low environmental impact."

Jan 1, 2014

By Y. Long

The deep-hole surface blasting technique is a prime method of iron ore mining. Blasting fragmentation is one of the important economic indicators that measures the blast method to obtain the iron ore. To improve the efficiency of the blasting method and further reduce the cost of the subsequent processing of iron ore, this paper summarizes measured data gained from a certain amount of blasting test conducted in an iron ore mine in Guangdong province, China. According to the data analysis, there are differences on iron ore blasting fragmentation by different indicators of deep-hole blasting, such as decoupling coefficient of charge, contact state between charge and borehole wall, and change of detonation position in charge. These factors were compared in terms of relevance and impact. Research shows: under certain rock conditions, the decoupling coefficient of the charge has a best range related to blasting fragmentation. Since the detonation position in charge determines the direction of propagation of the explosion stress wave through ore and rock, bottom initiation and mid initiation will help to improve the iron ore blasting fragmentation in joints fractured rock and ore. The research conclusions have important application value for program design of iron ore surface blasting and to guide other types of rock surface blasting.

Aug 1, 2013

The total current inventory of mature fine tailings is estimated to be nearly 850 million m³. Pressure has come to bear on the industry to accelerate its tailings management practices and prevent this inventory from steadily growing. The present paper describes the treatment, management and reclamation of fluid fine tailings. New technologies being evaluated include: i) Thin layered - fines dominated deposits, ii) Deep - fines dominated deposits, iii) Fines enriched sand deposits, and finally iv) water capped disposal in end pit lakes. A brief overview for each of the methods of treatment and disposal for fluid fine tailings is provided.

Aug 1, 2013

By A. de Ville d’Avray, G. Guezennec, P. Wavrer, E. Braak

The aim of the European CEReS project was to develop an innovative copper recycling route based on the coprocessing of coal production waste by bioleaching and printed circuit boards (PCBs) from Wastes of Electrical and Electronic Equipment (WEEE). Coal waste is processed by bioleaching in stirred tank reactors, and the resulting bio-lixiviant solution is used to extract copper from PCBs pre-treated by catalytic cracking. Copper is then extracted using solvent extraction, stripping and electrowinning. The whole process flowsheet combines thermal, biotechnological, physical and hydrometallurgical operations. Once the process concept has been validated at laboratory scale, a simulator of the whole process has been built in the USIM PAC software platform. The tool enables to improve the analysis of the results of the lab-scale experiments and to design industrial-scale scenarios by simulation. The results of such simulations allow to estimate the economical interest and to perform environmental impact assessment. After presentation of the CEReS project objectives and main results, the paper describes the methodology used to build the simulator and define the scenarios corresponding to feasible process routes. The main results of the simulations are then presented with technical, economic and environmental point of views. INTRODUCTION Because of rapid technological innovations in the electronics industry, electronic waste represents the fastest growing waste stream in the world, especially in developing countries (Işildar et al., 2018). Meanwhile, the global copper demand is expected to go on rising in the future. As significant amounts of copper are present in end-of-life printed circuit boards (PCBs), it becomes a necessity to develop efficient copper recycling routes. Metal refining from e-waste is traditionally performed by pyrometallurgical processes. However, the hydrometallurgical processing of PCBs, which has been shown to be technically feasible at laboratory scale with a wide range of leaching reagents, could be a less energy intensive and more flexible alternative (Tuncuk et al., 2012). However, a large amount of leaching reagent is required to leach the metals from PCBs.

Jan 1, 2019

By J. Mirza, E. Nicol, J. Lipkowski

Gold passivation in thiosulfate leaching media is a major barrier to its implementation. Addition of Cu (II) into the leaching solution has shown to aid in gold dissolution, but the mechanism by which it acts, and its role in the passive layer, remains unknown. Surface Enhanced Raman Spectroscopy (SERS), in tandem with linear sweep voltammetry, were employed to determine the dependence of leaching currents on mass transport and for fingerprint identification of sulfur species on the surface of gold. SERS leaching experiments were performed using gold nanorod electrodes that showed increased stability compared to other SERS active surfaces.

Jan 1, 2011

By Nima Nabavi

Shovels and excavators have significant blind spots due to their large sizes, increasing the chances of collision with other surrounding equipment such as haul trucks, loaders, and dozers. While a camera surveillance system is very useful in preventing collision, it can benefit from two additional features: (i) the ability to display the distance of the closest object within the view, and more importantly (ii) the ability to warn the operator if objects are getting too close. After a comparison between few different technologies, it is explained how these features can be provided by integrating rugged pulsar radar sensors with a camera system. The specific radar technology is already field proven in the harsh mining environments. Motion Metrics International Corp. has developed this exact product, which combines its 4-camera surveillance system (ViewMetricsTM) with a series of rugged radar sensor elements, named ViewMetricsTM-Radar. The radar system employs intelligent CAN bus communication to reduce wiring, hence improving hardware reliability with built-in troubleshooting features. A USB connection is the only hardware bridge between the radar sensors and the embedded computer. As such, an existing ViewMetricsTM system can be easily upgraded to ViewMetricsTM-Radar. As addition of new interfaces to the cab could result in operator distraction, this paper explains how ViewMetricsTM-Radar reduces distraction compared to other radar collision prevention systems.

Oct 1, 2009

By T. L. Lee, D. Y. Tan, J. Mi

Considerable progress has been made in studying the mechanism and effectiveness of using ultrasound waves to manipulate alloy solidification microstructure, However, uncertainties remain in both the underlying physics of how microstructure evolve under ultrasonic waves, and the best technological approach to control the final microstructure and properties. We used the ultrafast synchrotron X-ray phase contrast imaging facility housed at the Advanced Photon Source, Argonne National Laboratory, USA to study in-situ the highly transient and dynamic interactions between the liquid metal and ultrasonic waves/bubbles. The dynamics of ultrasonic bubbles in liquid metal and their interactions with the solidifying phases were captured in-situ for the first time. The experiments were complemented by the simulations of the acoustic pressure field, the pulsing of the bubbles and the associated forces acting onto the solidifying phases, providing more quantitative understanding for using ultrasound to control the growth of dendritic grains and to enhance grain multiplication effects for grain refinement.

Jan 1, 2014

By Te Gao

It is a general expectancy that in most of the construction and renovation project, the contractor is going to hand over the as-built documents to the owner or the facility management team at the completion of the project. The main challenge for the handover process is to ensure the completeness of the captured building information and the accuracy of it in terms of how well it represents the reality. Building information models (BIMs) can be used as an information repository to store and deliver as-built information. However, due to changes made in the construction and renovation phases and errors made in the design and modeling phases, discrepancies can exist between BIMs created in the design phase (asdesigned BIMs) and actual building conditions. Laser scanning technology is able to efficiently capture accurate geometric information, which provides an opportunity to identify and quantify discrepancies and update as-designed BIMs into as-built BIMs. This paper presents a case study, within which the asdesigned BIM of a newly renovated research lab was updated into an as-built BIM using laser scanned data captured in the renovation phase. This paper introduces the challenges associated with the updating process for the as-designed BIM. In order to address these challenges, this paper introduces a framework that supports the update of an as-designed BIM by incorporating point clouds captured by the progressive laser scans.

Aug 1, 2013

By Jan E. Nesset, L. Paul Staples

"High Gradient Magnetic Separation (HGMS) technology, although developed over 2 decades ago, has not been widely applied to the separation of sulphide minerals. Under conditions of strong magnetic field gradients, weakly magnetic minerals such as chalcopyrite (CuFeS2) and marmatite (Zn(Fe)S, sphalerite with iron in solid solution) behave paramagnetically and can be effectively separated from diamagnetic minerals such as galena (PbS). The application of this technology to the separation of Cu-Pb and Zn-Pb bearing streams in the treatment of fine grained complex sulphides may in some cases be more effective than separation by flotation. A 2 TPH Sala HGMS pilot plant was operated at Brunswick for a nine month period, ending in March 1995. The testing demonstrated the mechanical reliability of the technology, the consistency of operating results and the scale up from laboratory testing. HGMS is seen as a complimentary technology to flotation, best suited to performing those separations of galena (and other diamagnetics) which flotation does not do as well.IntroductionBackgroundSince the turn of the century, the magnetic character or magnetic susceptibilities of minerals have been determined with increasing precision and accuracy. Figure 1 illustrates specific magnetic susceptibilities of some common minerals. As long as susceptibility ranges do not overlap, separation is possible.In 1937, the principle of using a magnetizable matrix material in a magnetic field to increase both magnetic flux density gradients and number of capture sites for susceptible minerals was first applied (Frantz). It was not until the 1970's, however, that the genuine development of wet high gradient magnetic separation began with the introduction of very fine matrix materials to the magnetized volume of large solenoid magnets. Today, dozens of HGMS units purify, filter and separate minerals, primarily for the removal of iron stained minerals from clays used in the paper coating and china clay industries and for the recovery of fine titanium and iron oxides in the iron ore industry. Only the Garpenburg mill in Sweden is currently applying a continuous HGMS machine to separate complex sulphide minerals; upgrading a lead concentrate since 1988."

Jan 1, 1996