Search Documents

By Lionel C. Kilburn

"This geological engineering method is based on jour main characteristics of mineral properties, viz; location: inclusion of valuable mineralization; inclusion of geophysical and/or geochemical targets; and inclusion of geological targets. These are subdivided into a total of 19 subcategories, which are used to determine the value of the property.The nineteen subcategories are prioritized and assigned relative value factors from 1.3 to 10. Value of each mineral claim unit is determined by applying the appropriate subcategory factors to a base value of $400per 16.2 hectare unit. Property value is calculated by totalling the values of such individual claim-units.The boundary between ore grade and sub-ore grade must be estimated for each property under valuation, thereby making the method sensitive to mineral commodity prices.A clear and disciplined sequence of decisions based on personal experience forms the basis of this method. The method utilizes all factors normally used to value a mineral property.IntroductionIt is generally accepted in the exploration industry that valuation of exploration properties is a subjective rather than objective process (Roscoe, 1986; Lawrence, 1988; Lawrence, 1989; Woodcock, 1985), and that it is greatly influenced by the experience and qualifications of the person who is doing the valuation. However, the significantly low degree of objectivity in mineral property valuation at this point in time invites effort to achieve a more quantitative engineering basis.Value of a mineral property depends basically upon metal prices, recoverable grades, mining and metallurgical practices, commodity supply and demand , and political-economic conditions, all of which vary with time. Therefore, any valuation is valid for only that point in time when it is made. Mineral deposits can decrease as well as increase in technical value with time."

Jan 1, 1990

By D. A. Stokes

"In October of 1980, Fording's 15 000-ton capacity clean coal silo was put into operation. The silo was unique in that it was designed to allow the mass flow of material, coupled with a sophisticated computer-controlled dynamic loadout/weighing system.On May 1, 1982, an explosion, attributed to a methane buildup, devastated the top of the silo. .As a contingent plan to minimize the effect of the production loss the conveyance to the silo top was reconstructed and the silo' was back in operation by mid-June 1982, although the silo top was left open to prevent further methane buildup. As dust emissions occurred during loading ofthe silo, an extensive study was undertaken to establish dust control for the silo, while at the same time providing methane detection and control.The study, conducted for Fording by the Cambrian Engineering Group of Calgary, involved an extensive search and investigation of existing coal silos. The study concluded that there IS no universally accepted method of controlling methane emissions in coal silos.The study also produced a unique conceptual design for handling methane, while at the same time, protecting the environment . Fording's Clean Coal SiloThe silo, located at Fording Coal's Fording River metallurgical coal operation, is utilized for the storage and load out of cleaned thermally-dried metallurgical coal.The silo was constructed in 1979 and 1980 to reduce unit train loadout times and to facilitate the handling of “special shipments"" of coal. The silo went into operation in October 1980, under manual control and utilized computerized, automated loading by February 198I.The silo is 21 m in diameter and 76 m high, with a nominal capacity of IS 000 live tonnes. The coal storage portion of the silo is 21 m in diameter and 48 m high, utilizing 2 steep-angled hopper outlets allowing mass flow of the stored coal during train loading. Each hopper has a control gate and a discharge chute, one chute for bulk loading, the other for trim loading of coal into the rail cars."

Jan 1, 1986

By Steve Forgeron, Brendan MacKenzie, Kevin MacPherson

"The geological composition of strata immediately adjacent to coal seams has a significant effect on the safe and efficient extraction of coal from underground mines of the Sydney coalfield. Geological features such as paleo-sandstone river channels, seam splits, floor rolls, paleo-soils and stone-filled rupture features can rapidly alter the competency of immediate roof and floor strata, significantly reduce the height of the coal seam, cause rapid variations in seam gradient and influence the in situ and run-of-mine quality of the coal.The impact of these features on the over-all mining operation can be significantly reduced if mine management can be for-warned of their impending occurrence. Using the information acquired from boreholes, geological mapping, x-ray diffraction analyses, microscopic studies, geophysical logs and seismic surveys, sedimentary models have been constructed which enable the mine geologist to predict, with increasing accuracy, the future occurrence of deleterious geological features ahead of the working face."

Jan 1, 1986

By J. R. Morris, A. E. Ball, G. W. Kuzyk

"AECL Research has constructed an underground laboratory for the research and development required for the Canadian Nuclear Fuel Waste Management Program. The experimental program in the laboratory will contribute to the assessment of the feasibility and safety of nuclear fuel waste disposal deep in stable plutonic rock.In 1988, AECL extended the shaft of the Underground Research Laboratory (URL) from the existing 255 m depth to a depth of 443 m in cooperation with the United States Department of Energy (USDOE). The project, which involved carrying out research activities while excavation and construction work was in progress, required careful planning. To accommodate the research programs, full-face blasting with a burn cut was used to advance the shaft. Existing facilities at the URL had to be modified to accommodate an expanded underground facility at a new depth. This paper discusses the design criteria, shaft-sinking methods and approaches used to accommodate the research work during this shaft extension project.IntroductionThe Underground Research Laboratory (URL), a major geotechnical research facility, has been developed by AECL Research, 120 km northeast of Winnipeg, Manitoba. The URL is part of the Canadian Nuclear Fuel Waste Management Program (CNFWMP), which is assessing the concept of nuclear fuel waste disposal in a vault deep in stable plutonic rock of the Canadian Shield (Hancox, 1986). The URL provides a representative environment to conduct a wide variety of geotechnical research relevant to nuclear waste disposal. Extensive characterization and monitoring programs were carried out prior to construction and will continue during operation. The operating phase experiments began in 1989 and will continue until the year 2CXXl (Simmons, 1990). Figure I shows the present extent of the URL facilities and the proposed future development."

Jan 1, 1991

By M. P. Filion, K. Ferguson, L. L. Sirois

Acidic drainage is the largest single environmental problem facing the Canadian mining industry today. Technologies to prevent acidic drainage from occurring in wasterock piles and tailings sites, and on the walls of open pits and underground mines, need to be developed and demonstrated. There are two groups in Canada which have accepted this challenge: the national Mine Environment Neutral Drainage (MEND) program and the British Columbia Acid Mine Drainage (BCAMD) Task Force. This paper summarizes the activities of these two organizations.

Jan 1, 1990

By Jacques H. Nantel, James F. Archibald

"Frozen tailings material may be required, in the future, to perform the support functions of underground backfill in mines located in zones of permafrost, notably in the high Arctic. To date, no knowledge of physical support parameters of such materials has been obtained in Canada due to the limited mining activity in permafrost regions. It is therefore judged essential that the important physical and mechanical properties relating to frozen tailings material be assessed.Innovative mining methods will be required to cope with the harsh environmental conditions that exist at mining sites in the Canadian Arctic. A preliminary laboratory study, in the absence of field trials at limited Arctic mining sites, has been completed in which the physical and mechanical properties of several types of representative mill tailings mixtures have been investigated. A variety of tests, to determine frozen slurry and pelletized tailings strength properties, moduli of compression, optimum water contents, deformation characteristics and the like, have been conducted.The results of this study will be used to establish guidelines for the suitability of tailings use in such northern mining environments. IntroductionFrozen tailings material has never been used to backfill underground openings in Canadian mines. At present only one Canadian mine, the Polaris Mine situated on Little Cornwallis Island, is investigating the use of frozen backfill. However, the Canadian North covers a large territory and potentially contains a large number of mineral deposits. The understanding of concepts related to mining activities in sub-zero frozen ground is therefore important.The implications of using frozen tailings as underground backfill material are far reaching both from the point of view of mine stability and disposal of tailings in the arctic regions.The strength of frozen materials (soil, backfill, etc.) may take on different meaning depending on the engineering situation. Both the concepts of rupture and excessive deformation need to be considered.The functions usually required to be performed by the backfill material in underground mines may be summarized asfollows:a) working floors; such as in cut-and-fill stopesb) stope wall support; for cut-and-fill and delayed fill stope~c) self-support when backfill is exposed on one face; during pillar recovery phases.For fill functions such as working floors, the short-term response of the frozen fill is the dominant concern. For the other fill functions, the long-term deformation response of the frozen fill, or creep, is of interest."

Jan 1, 1986

By W. G. Davenport

Methods of extracting copper are evaluated in terms of innovations during the 1970's, and predictions to the end of this century are made. It is concluded that between one and two new smelters and refineries will be needed per year until the turn of the century, and that most of these smelters will be of the oxygen or oxygen-enriched flash furnace type. For converting, the Peirce-Smith converter will still predominate, but the Hoboken converter will play an increasingly important role. Five Japanese pollution control systems are described and it is suggested that much of this technology will be included in future smelting installations. Further growth of hydrometallurgy is predicted, especially for oxide ores, based on improved product metal quality and low plant cost. A n increased level of scrap resmelting is also expected.

Jan 1, 1980

By J. E. Danoczi

Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne area kimberlite field in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as ?gently? as possible since essential to the diamond liberation process is the minimization of diamond damage, particularly for the larger, high value diamonds. The Southern African diamond mines traditionally use Jaw and Gyratory crushers as their primary comminution method. However, these diamond mines generally process the harder, competent kimberlite that is located in the diatreme zone as well as the root zone of the volcanic pipe. Softer kimberlite is typically located in and around the crater area of a volcanic pipe and it is this source of kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills, this being the preferred method of comminution for minimizing diamond damage.

Nov 1, 2011

By D. François-Bongareon

"In previous publications by the author, significant advances and generalizations of the theory of sampling of broken ores, prompted and confirmed by experimental results, have been presented. This paper shows how to implement these theoretical results in practice. The models to be used are reviewed, with a description of the various sampling parameters involved. Then the methodology for the experimental assessment of those parameters, including segregation factors, is described in simple and practical terms, along with the use of handy sampling protocol charts. Finally, the particularly important case of processing data from a sample-tree experiment is detailed, and examples of applications covering all situations and types of experiments are provided.IntroductionThe reliability of a sample of crushed material , i.e. the expected (average) deviation between its true grade and the true grade of the lot it comes from, mostly depends upon six factors:• the size (mass) of the sample (and to a minor extent, for small lots, the size of the lot);• the size of the rock particles (degree of comminution)• the nature of the mineralization at microscopic scale (i.e., within even the smallest particles);• the geological nature of the mineralization and mineral of interest;• the grade of the lot in the mineral of interest; and• in some cases, the state of segregation of the lot.In practice, one should first disregard segregation problems, and assess sample variability in the segregation-free case. Once the numerical parameters governing this variability have been assessed, then segregation factors can be assessed in turn. In the case of laboratory standard sample preparation procedures, segregation can usually be disregarded altogether."

Jan 1, 1993

By Jaime V. Ongpin

"The author will give a capsule history of Benguet Corporation and attempt to identify its operating environment and underlying ""strategy"" until 1974, when the company's management assumed office. The company's operating environment and ""interim strategy"" from 1975 to 1980 will be described. The discussion will cover an environmental forecast and define the company's"" strategy for survival"" for the balance of this century.IntroductionIn December last year, I was asked to deliver a pa per for the management lecture series a t the Asian Institute of Management in Manila. The paper was entitled "" The 1970's: A Decade of Disaster For New Mining Projects"" . In that paper, it was my task to review the results of new mining projects in the Philippines during the previous decade. The task was not a happy one, for the results themselves were not only unhappy, but disastrous on a scale unprecedented in Philippine history. Out of a total of 17 major mining project s involving an aggregate capital investment in excess o f US $2 billion during the 1970s, only three project s have been profitable, and all the rest have either gone "" belly up"" or are teetering on the very edge of financial disaster.It is in the context of this shocking record of widespread financial dislocation in the Philippine mining industry, (which in varying degrees appears to have been paralleled in virtually every other country in the world where mining is an important sector of the economy) that I address myself tonight to the theme of this symposium. My paper is entitled ""Risk Management Strategy in Mining"" and it is sub titled ""Can Benguet Corporation Survive to Celebrate its Centennial in 2003?"". I have inserted the word ""Strategy"" and added the subtitle, because I wish to make it clear first, that my presentation to you tonight will be focused exclusively on the strategic aspect s of risk management, and second that I will limit myself to Benguet's own ""in-house"" experience and perspectives on this subject. I would caution you therefore, to consider my views within this restricted framework, and in light of the particular and sometimes peculiar circumstances within which Benguet Corporation operates."

Jan 1, 1983

By J. M. Skeaff

"The main solution, ore and residue pulp streams in the Rio Algom Quirke I uranium mill at Elliot Lake have been sampled and analyzed for radium-226. Analysis of the ore and leached residues indicates that Ra-226 dissolves and precipitates within the first pachuca tank. A maximum of approximately 0.2% of the Ra-226 in the ore remains in solution during leaching.IntroductionConcern over the acid drainage and radionuclide dissolution problems associated with uranium tailings disposal sites in Canada has prompted investigation into methods for improving current uranium processing practice.Present commercial practice usually involves leaching of the uranium ore with sulphuric acid, ion-exchange separation of the uranyl sulphate complex from the leach liquor and"" precipitation of the uranium as yellowcake. Daughter products of U-238, such as Th-230, Pb-21O and Ra-226 remain with the tailings and undergo long-term dissolution.Table I summarizes the probable behaviour of the radionuclides during milling. The concern here is with Ra-226, because it will deposit in the bones if ingested and is ""thus considered a serious health hazard(1), Similarly, Po-218 and Bi-214, which are daughter products of Rn-222, can be retained in the lungs and are considered to be the principal sources of radiation dosage(2) arising from the inhalation of Rn-222. Previous investigations(3-9l indicate or imply that Ra-226 undergoes redistribution during milling. However, detailed published information on the behaviour of Ra-226 in the uranium milling process appears to be lacking. A knowledge of the behaviour of Ra-226 in uranium mills, particularly during leaching, could lead to improved methods for its control.This paper reports the occurrence of Ra-226 in the Rio Algom mill. The main objectives of the study were to determine (1) the distribution of Ra-226 within the solids, (2) at what point, and how rapidly, redistribution occurs and (3) whether there are high concentrations of Ra-226 in solution."

Jan 1, 1981

By A. MacKinnon, P. W. Kingston, W. F. Caley

"Wollastonite (CaSiO3]) is experiencing increased usage in a variety of applications, such as fillers in paints, plastics and resins, as an extender to replace both non-fibrous and fibrous materials (e.g. asbestos), and in the glass and ceramics industries. Significant new deposits of wollastonite have been discovered in Marmora Township, about 175 km northeast of Toronto. The geological setting of these large-tonnage. High grade deposits has recently been investigated to assess the possibility of their development. A preliminary study of the chemistry, as well as the mineralogy of six occurrences is presented. Based upon this information, it is suggested that several of the deposits have an excellent development potential.INTRODUCTIONWollastonite is an anhydrous calcium metasilicate (CaSiO3), with a theoretical composition of 48.3% CaO and 51.7% SiO2; the calcium may be partially replaced by iron, manganese, magnesium, and strontium. Commonly associated minerals include diopside, tremolite, idocrase, grossularite andradite, quartz, and calcite. Wollastonite forms as a contact metamorphic mineral within impure limestone near intrusive bodies of granite, or other acidic rocks, as the result of metasomatism of calcareous sedimentary rocks, or by the crystallization of certain magmas (e.g. carbonautes). Generally, the reaction of calcite with silica to produce wollastonite occurs when siliceous hydrothermal fluids from a granitic intrusion or primary silica in the limestone/marble react with calcite in limestone at temperatures between 450°C and 600°C."

Jan 1, 1989

By James Tuer, John R. Goode, Jim Cambon

"Hudson Resources Inc. (Hudson) has defined a major resource of high purity anorthosite (calcium feldspar) assaying about 30% Al2O3 at the White Mountain (Naajat) deposit in Western Greenland. Extensive beneficiation and evaluation testwork has shown that the material can be simply beneficiated to produce a feed material ideal for the production of low-alkali E-glass used for making glass fibre. An offtake agreement is in place with a major US fibreglass manufacturer and, subject to the mine construction schedule, shipments are scheduled for late 2016 or early 2017. In parallel with the E-glass program, Hudson has completed an initial program of metallurgical testwork which shows that the White Mountain anorthosite can be processed by hydro- and pyro-metallurgical processes to yield either smelter-grade alumina (SGA), suitable for conversion to aluminium metal, or a high purity, chemical/specialty-grade alpha-alumina (CGA) commanding a premium price. The process includes dissolution of the anorthosite in hydrochloric acid, HCl sparging to precipitate aluminium chloride hexahydrate (ACH), recycle of the ACH filtrate to leaching with a bleed stream processed for HCl regeneration from CaCl2, and two-stage calcination of the ACH to regenerate HCl and produce SGA and/or CGA. Calcium silicate and amorphous silica are marketable by-products. This paper discusses the White Mountain anorthosite deposit; the process testwork completed to develop production processes for SGA and CGA; production plans, and indicative economics.INTRODUCTIONHudson Resources Inc. (Hudson) holds a 100% interest in the Naajat Exploitation Licence in Western Greenland that cover the White Mountain high-calcic anorthosite deposit. Anorthosite is a calcium aluminosilicate of slightly variable composition but generally containing about 30% Al2O3. The alumina content is similar to that in bauxite and anorthosite has long been studied as a feedstock for the production of alumina. Other potential uses include feedstock for the high-end fiberglass (E-glass) industry and as a filler for use in paint and plastics."

Jan 1, 2016

By H. Stocker, C. E. Makepeace

"This paper presents the statistical analyses of several sets of data acquired in several programs of sampling of radon daughters in uranium mines. The measurements were taken over periods of days or weeks for given locations or location occupations within these mines. Because the sampling applies to specific intervals of time and specific locations, a method is suggested f or the eventual application of a monitoring program which would be suitable on an annual basis for these locations. The present data and analyses thereof are not justifiably applicable to a monitoring regimen on an annualbasis, without a number of additional assumptions.The aim of the present analyses of concentration measurements is the determination of the minimum number of measurements required to achieve an annual radon daughter exposure estimate, for individual workers, having an error no greater than 50% at the 95% confidence level. The criterion of accuracy is taken from a statement in the American National Standard, Radiation Protection in Uranium Mines (ANSI NI3.8-I973), and is currently used, in somewhat modified form, as a guide to uranium mining licensees in Canada. Uncertainties associated with occupancy time are ignored in the present analysis. IntroductionOne of the principal aims of any scheme of radiation protection is that of improving the accuracy of exposure estimation for workers. The example presented here is from the area of radon daughter exposure estimation for uranium miners. The conventional means of estimating workers' exposures is grab sampling of radon daughter concentrations combined with occupancy time weighting in the various work and travel locations. Uncertainties exist in each of these components, and in an environment of highly variable radon daughter concentrations (such as an active uranium mine) one is always uncertain as to the representativeness of the grab sample (compared to the average concentration) unless a sophisticated monitoring scheme has been implemented based on previous experience in such an environment.Improvements in the accuracy and precision of employee radon daughter exposure records depend, primarily, on three factors;"

Jan 1, 1980

By E. Contestabile, T. R. Craig

"This report describes the development and effective use of shaped charges as part of the Elliot Lake Mine Roof Stability Project to remotely remove the heads from roof bolts. With a slight modification, these same shaped charges are being recommended f or use to the Brunswick Mining and Smelting Corporation Limited (Mining Division), to cut steel cable bolts.IntroductionThe Canadian Explosives Research Laboratory (CERL) often receives requests to cooperate in solving problems encountered in private industry or other sectors of the government. CERL is equipped to design and test explosive and pyrotechnic devices and the policy is to treat each case individually.The first case reported evolved from a request from a sister laboratory at Elliot Lake. The intent was to remotely remove the head s of roof bolts as part of a mine roof stability project. The device designed for this use was 1000,70 effective in the laboratory and 80% effective in the mine.The second case reported results from a request from a private mining company knowledgeable of the Elliot Lake Project. Their requirement was to remotely cut cable bolts. This request was first treated as presenting a new problem. The solution, however, proved to be very similar to the former."

Jan 1, 1985

By G. R. Davidge

"Falconbridge Mine has a history of significant microseismic activity dating back to 1955. Since mid-1981, a microseismic monitoring system has been operating in the area around the No .9 Shaft hoist room located 25 m from the are zone at a depth of 1200m. Several mine wide faults dissect this area and have been shown to be microseismic-active due to mining. The microseismic monitor has been interfaced with a small dedicated personal computer and a communications device to perform routine data evaluation and to produce graphical output. The programs are described and selected result s from the monitoring program are presented.IntroductionFalconbridge Mine is located on the southeast rim of the Sudbury Basin. The nickel-copper sulphide ore zone is essentially a tabular orebody striking approximately east-west and dipping at 80 degrees north near surface and rolling to 75 degrees to 80 degree s south by the 1000 level. (Mine level number s represent the approximate depth in feet below ground surface .) This dip is maintained down to the 6000 level. The north wall is comprised of jointed norite and a faulted contact up to 1 m thick exists between the ore zone and the norite. The south wall rock is a greenstone with highly siliceous lenses and often has a faulted contact with the ore zone. No less than five mine wide faults exist, as shown in Fig. I.Mining ha s been carried out from virtually the bedrock contact to depths of 1830 m although the majority of current activity is between 900 and 1500 m below surface. A winze provides access below the 4025 level and the cage hoist room is located on the 3850 level in the north wall 25 m from the contact. Because of concern for the stability of this hoist room, there has been no mining activity within 60 m of the hoist room and by 1980 this block of ore was one of the major blocks of high-grade ore remaining in the mine . Mining of this block was originally scheduled for very late in the decade.Prior to a six-month shutdown in 1982, this mine produced approximately 450,000 tonnes of ore annually, mainly by cut and- fill techniques. Following the shutdown, annual production has been reduced to approximately 200,000 tonnes and production is now mainly by undercut and fill techniques .Mining-induced seismicity has occurred at Falconbridge Mine since at least 1955 and reviews of the microseismic problems for the periods from 1965 - 1970 and from 1971 to 1979 were made by Singh (1971) and Vongpaisal et al. (1980), respectively. The need for instrumentation was addressed by these authors. Following several large events during the spring of 1980, a decision was made to investigate existing microseismic monitors and to apply micro seismic monitoring techniques in Falconbridge Mine. Application of microseismic monitoring to Falconbridge Mine was to concentrate on the No . 9 Shaft hoist room area of the mine, particularly around the 4025 level where a large mechanized cut-and- fill stope was approaching this level. By mid - 1981, the microseismic monitor was fully installed and with in a year , a short-period seismograph and a personal computer had been added to the system."

Jan 1, 1984

By Nick Vagenas

"Loading and transportation are important activities of the mining process. Automation of these activities in underground hard rock mining has been discussed for a long time. This paper deals with the performance evaluation of a prototype automatic Load-Haul-Dump (LHD) vehicle (a 7-ton GHH LF LHD model) operating in Zinkgruvan mine, Sweden. The purpose of the data analysis is to evaluate the operational and maintenance characteristics of the automatic LHD system in the mine. Graphical and numerical methods have been used for the statistical analysis of the data. IntroductionDuring the past years, the idea of integrated automation and tele-operation on Load-Haul-Dump (LHD) machines (Fig. 1) has attracted considerable interest in the Swedish mining industry. This is mainly due to the demand for improvement in the working environment and due to the rapid development of economic and reliable microprocessors for mining vehicles. Several advantages can be foreseen with the application of a Remote-controlled/Automatic LHD (RAL) system in underground mining. Some of them are (1)':• better utilization of working hours;• less interruption in production at shift changes;• better operational control of a fleet of vehicles;• improved safety; and• one operator may be able to operate more than one vehicle simultaneously."

Jan 1, 1993

By David Rahal, Saul Ortiz, Maria Escobedo

The general trend in the minerals industry is towards the processing of fine grained, disseminated mineral deposits. This has led to an increase in the number of fine/ultra-fine grinding installations using stirred media mills. The challenge is that both the equipment type and the mineralogy of the deposit have an effect on specific energy consumption. Fresnillo PLC recognized this issue and addressed it by providing samples for testing in a laboratory regrind system. The objective of the test program was to determine the specific energy required to achieve a product size of 10 µm (P80). A specific energy plot was generated for both a lead and zinc flotation concentrate. It indicated that 34 kWh/t and 51 kWh/t were required for the two samples (Pb and Zn respectively). This difference highlights the effect of mineralogy on the energy required for fine grinding. The regrind feed and products were submitted to a range of basic mineralogy tests to quantify the mineral differences that could have changed the specific energy requirements. These tests provided general mineralogy, documented optical textures, and provided particle size microscopy. The lead concentrate was found to contain significant amounts of silicates in addition to the dominant sulphide, pyrite. The zinc concentrate was determined to be mostly sphalerite with minor amounts of quartz, chalcopyrite, pyrite and galena. The material testing results illustrate the importance of basic mineralogy studies in conjunction with comminution testing to determine specific energy consumption.

Jan 1, 2016

By J. E. Udd, L. B. Geller

"Responding to requests by the Canadian mining industry and the mine regulatory authorities, the Canada Centre for Mineral and Energy Technology (CANMET) undertook a major research project on evaluation of wire rope testing in 1986. The objectives were to document, analyze, and clarify - in basic operational terms the reasons for ongoing mine shaft wire rope failures that occur despite mandatory non-destructive testing (NDT) with electromagnetic (EM) instruments on a routine basis.The project's investigative scope and depth was unprecedented. It could not have been successfully completed without the wholehearted cooperation of industry, research organizations, and mine-inspectorates at both national and international levels.The project's goals were attained. II was shown that, at present, the problem areas in Canada are oj a human , rather than of a hardware-related nature. Consequently, the principal recommendations are concerned with a more widespread, more uniform and thorough operator training and certification process at industrial and regulatory levels. Secondary suggestions concern areas of hardware-related improvements.In this paper an up-to-date general overview is given of the major project results. A n extensive reference list is also provided of papers that contain all relevant documentation in detail."

Jan 1, 1992

By L Mariani, G. Mendoza-Suarez

In this investigation, TiH2 powders were coated with copper and nickel by electroless plating to delay hydrogen evolution. Copper-coated samples were found to have a mixed acicular (2D growth) and cauliflower (3D growth) morphology whereas the nickel-coated samples had a cauliflower morphology. Examinations of the coated powder cross-sections revealed that the coating thickness ranges from 0.2 µm to 4 µm. Uncoated areas on the powder surface and coating flakes unattached to TiH2 particles suggest poor adhesion between the coating and the substrate. The phase transformation undergone by the TiH2 during dehydrogenation was studied in samples taken at intermediary points in the heating cycles and examined by XRD. The findings reveal that as the powder is heated from room temperature to 800°C, it changes from TiH1.971 to Tiu and to aTi. Differential Thermal Analysis (DTA) was performed to study the effects of the coatings on the temperature of hydrogen release. It was found that increasing the number of plating iterations, and therefore the thickness of the coating, creates a significant shift in the temperature of gas release.

Jan 1, 2006