Search Documents

By G. Tozsin

A six-stage sequential leaching procedure was used to assess the leachability of heavy metals from waste rock in Antamina Mine. Sequential extractions procedure is well established for fine and small (? 1g) samples. However procedures for coarse and large test samples are lacking. This study presents results of the sequential leaches tests conducted on relatively coarse and large representative samples in terms of the availability and mobility of metals. Selective chemical reagents were used to extract metals from six different fractions where metals released with each subsequent extraction are believed to be bound tighter than those released in prior steps and therefore less likely to be leached.

Aug 1, 2013

By K. D. Peaslee, J. M. Soto, IéDé Smith, A. D. Saikia

Spinel-forming refractories reduce penetration of metal and slags through a tightening of the lining resulting from the volume expansion associated with spinel formation. Sintered spinel is often added to reduce the overall volume increase that results. Tests were carried out to evaluate the difference between performance in spinel¬forming and spinel-containing refractory mixes. Eight refractory linings, one (1) pure magnesia, three (3) magnesia-base spinel-forming and four (4) alumina-base spinel- containing dry vibratable mixes, were tested for four hours in contact with a low-carbon, low-manganese steel in a coreless induction furnace at temperatures in excess of 1600°C. Afterwards, sample were cut, and wear and penetration were measured. For magnesia-based mixes wear was minimized using 20-30wt. spinel formation although further experiments are required to determine the optimal value. For alumina-based mixes, there seemed to be an optimal ratio of spinel added to spinel formed that minimized penetration and wear at the slag line. Sidewall accretion occurred and the accretion was the highest for the mix with the ratio of spinel formed to spinel added near the optimum value. Therefore to design an optimum refractory mix the benefits of higher ratios of spinel added to reduce penetration and wear at the slag line will need to be balanced with the tendency to form accretions on the sidewalls of the furnace.

Jan 1, 2004

By H. Fujihara, K. Uesugi, H. Toda, A. Takeuchi, K. Shimizu

"Hydrogen is trapped at a variety of microstructures, for example grain boundaries, dislocations and particles. It is thought that hydrogen trapped at trapping sites is redistributed to the other sites under loading and then brittle fracture occurs with hydrogen accumulation. In order to understand hydrogen embrittlement behavior, it is necessary to investigate the time evolution behavior of hydrogen accumulation at each trap site. In the present study, changes in hydrogen distribution are observed under stress using Kelvin force microscopy (KFM) that can visualize hydrogen concentration distribution on material surface at high resolution. Spot-like hydrogen enriched regions are observed on the surface of a material. In addition, hydrogen depleted regions are observed around those enriched regions, and the appearance of hydrogen trap due to particles existing near the material surface is revealed. On the other hand, hydrogen trapped at grain boundary can be visualized. From in this result, it was suggested that crystallographic factors influence hydrogen accumulation. The relationship between initiation and propagation of intergranular crack and hydrogen accumulation under stress will be discussed.INTRODUCTIONHydrogen present in a metal sometimes has significant effects on various properties. Hydrogen in a metal is trapped at a variety of microstructure, for example dislocations and grain boundaries. Grain boundaries, dislocations and micro pores are the major trap sites in aluminum alloys. Some researchers considered that hydrogen redistribution and accumulation between these trap sites in a material with loading plays an important role in the brittle fracture behavior. In general, in intergranular fracture and quasi-cleavage fracture, the hydrogen trapped at grain boundaries and dislocations contributes to fracture behavior, respectively. Recently some researchers have shown that the ductile fracture in aluminum alloys is resulted from growth and coalescence of hydrogen micro pores. Analysis using first principles calculation indicates that intergranular fracture occurs when hydrogen concentration reaches 20 atom H/nm2ongrain boundary. From this report, it is considered that hydrogen redistributed during deformation accumulates locally in order to cause hydrogen brittle fracture. In order to understand hydrogen embrittlement, it is necessary to investigate the time evolution behavior of hydrogen accumulation at each trap site. In the present study, we evaluate the relationship between hydrogen accumulation behavior and fracture behavior in Al-Zn-Mg based alloys. In-situ observation was made by combining the tensile test with Kelvin force microscope (KFM) that can visualize the hydrogen concentration distribution on the material surface with high resolution. We also investigate the relationship between hydrogen distribution behavior and crystal orientation."

Jan 1, 2018

By E. A. Haack, L. A. Warren

Microbial biofilms are essentially biologically driven, geochemically reactive interfaces between solid surfaces and aqueous solution. Field investigation of acid rock drainage (ARD) associated biofilms at the Onaping nickel mine (Onaping, ON, Falconbridge Ltd.) characterizing: (1) micro-geochemical gradients (pH and 02) (2) metal fractionation amongst biofilm solid components, and (3) microbial communities; over both seasonal and diel timescales, indicates biofilms are highly metal reactive. Results show that biofilms accumulate metals seasonally within two microbially controlled solid fractions: amorphous hydrous manganese oxide (HMO) biominerals and the organic biofilm matrix. The biofilm geochemical microenvironment, driven largely by microbial activity, dynamically impacts biofilm metal behaviour over diel timescales. These results indicate that microbes can play significant roles in bulk system reactive metal transport. On-going investigation seeks to characterize the microbial players and the microbial-geochemical linkages involved in Mn oxyhydroxide formation and subsequent metal sequestration, with the goal of engineering this microbial activity as a bioremediative approach. This approach will have utility beyond specific application to the Falconbridge Onaping site to ARD mine environments in general, as the likely microbes involved in these processes are typically common across ARD systems.

Jan 1, 2004

By T. Yalcin

"This paper describes a process that can provide high rates of dewatering and that has the potential of bringing significant savings in tailing disposal costs. It involves a three-stage, closed-circuit operation employing a hydrocyclone, a settling cone and a thickener. The mill tailing, with adjusted pulp density, is first fed to the hydrocyclone. The underflow from the hydrocyclone goes to the settling cone for further dewatering. The overflows from the hydrocyclone and the settling cone are sent to a thickener which, with the addition of a flocculant, gives a clear liquid effluent and a dilute underflow which is recycled back to the hydrocyclone. The underflow of the settling cone is a material with as high as 78% pulp density and is suitable for direct disposal or for use as mine backfill.INTRODUCTIONDewatering is an essential process for the disposal of mill tailings and forms an additional cost item in milling operations. Cost-cutting measures are therefore desirable in this area as in any other stage of milling. One way of achieving this is through increased rate of dewatering which would require smaller dewatering units with correspondingly lower capital and operating costs."

Jan 1, 1987

By Sina Mostaghel, M. Guo, E. Klaffenbach

The current paper is focused on evaluating the behavior of copper in a copper production slag and the assessment of metal recovery possibilities. For this reason, thermodynamic calculations were carried out to determine the influence of parameters such as slag composition, temperature and oxygen partial pressure on recovery of non-ferrous elements. It was found that the formation of a solid face centered cubic (fcc) phase, mainly consisting of iron, limits the extent of reduction that can be achieved for an industrial process. However, it could be discovered that solubility of iron in the Cu-rich liquid alloy strongly depends on presence of other elements, particularly arsenic. As part of the results of this study, the solubility of Cu in the slag at onset of fcc phase formation is presented as function of temperature, oxygen partial pressure and concentration of MgO and CaO. It was concluded that lower temperature (1200°C) and higher CaO addition (16 mass-% in this study), would result in the highest achievable copper recovery from slag. INTRODUCTION Copper slag is produced as a by-product of the copper production process. The slag is still containing a high amount of copper and other valuable metals. This demands further treatment of the slag as a secondary source of metals. In addition, the physical/mechanical properties of slag allow its use in several applications such as hydraulic engineering, civil engineering, as an abrasive and many more. These applications help reducing the use of natural resources like rock and sand. By decreasing the content of heavy metals such as Cu, Pb, Zn and As in the slag, its application in abovementioned fields becomes more attractive as the probability of releasing these elements to the environment is further reduced. To develop a pyrometallurgical slag reduction process, it is necessary to understand what describes the end point of the reduction. This point is expected at maximum copper recovery without facing operational challenges. Existing literature provide some information on the effect of different parameters such as temperature or concentration of different slag formers, on solubility of copper and heavy metals in different phases. However, due to complexity of industrial slags, equilibrium experiments and accurate thermodynamic modelling are essential to be able to reliably predict the behavior of different elements in the system and determine the end-point of reduction.

Jan 1, 2019

By J. H. Baek, D. W. Lee, B. K. Kim

Nanostructured Cu-Al203 composite powders were synthesized by thermochemical process for an electrode application. The synthesis procedures are 1) preparation of precursor powder by spray drying of solution made from copper and aluminum nitrates, 2) heat treatments to evaporate volatile components in the precursor powder and synthesis of nanostructured CuO+Al2O3, and 3) CuO reduction by hydrogen into Cu. The suggested procedures stimulated the formation of the gamma-Al2O3. The mean particle size of the final composite powders was 20nm, and the electrical conductivity and hardness in the hot-extruded bulk were competitive with Cu/Al2O3 composite by the conventional internal oxidation process.

Jan 1, 2004

By E. Kordzadeh, M. Reza Bateni, M. Karaminezhaad, A. Moeini

A series of austenitic heat resistant Fe-Ni-Cr-Al alloys with different nickel contents have been investigated at 1100 ° C and 25, 50, 50,100 hours in S/0 bearing atmospheres. Before sulphidation test, the specimens were annealed in argon at 1250 °C for 8 hrs. Weight changes were measured using an automatic thermo gravimetric analyzer and corrosion products were analyzed by scanning electro microscope (SEM), energy dispersive X-ray spectrometry (EDAX), X-ray diffraction and optical microscope. The results showed that sulphidation resistance decreased with increasing nickel content. Internal sulphidation controlled by gaseous transport through cracks and pores and the formation of internal sulphide increased when liquid sulphides formed on the surface.

Jan 1, 2004

By George Hope, Dave Green, Jacques McMullen

The Est Malartic mill has been treating massive sulphide, copper/gold ore from the Bousquet 2 mine since 1989. The need to minimize copper content in flotation tails which are leached for gold recovery and to produce a saleable copper concentrate led to the evaluation of Conventional, Column and HG flotation methods. The HG method was preferred and two full-scale cells were installed and operated over a two-year span. In 1992, it was decided to expand the mill capacity from 1500 tpd to 2500 tpd. A total of nine additional HG Tank Cells were installed to provide additional roughing and cleaning capacity. The expanded plant has been operating since June 1993.

Jan 1, 1994

By P. Lauzon, C. Oprea, S. Zhou, G. Oprea, J. Rigby, T. Troczynski

Hydration of basic refractories could occur during storage, drying after installation or in use. In order to assess the hydration resistance of various commercially available magnesia-chrome bricks, hydration tests were performed in steam at 110, 120, 130 and 150°C. The changes of the modulus of elasticity by the impulse excitation method, apparent porosity, air permeability, average pore size and pore size distribution were correlated with the hydration data. Mineralogical and microstructural changes were also studied on selected specimens by XRD and SEM/EDS. The hydration mechanisms were discussed in correlation with the chemical and mineralogical compositions of the experimental bricks, in particular with the nature of the mineralogical phases at the grain boundaries.

Jan 1, 2004

By J. H. Baek, S. Alexandrovskii, D. W. Lee, B. K. Kim

Nano-phase titanium carbide was synthesized by Mg-thermal reduction process using a novel route of Mg-thermal reduction. The processes are based on I) feeding of TiC14+CxC14 x = 1, 2 ) solution into liquid magnesium, 2) Mg-reduction of metal chlorides, 3) TiC formation by the reaction of released Ti and C atoms, and 4) vacuum separation of residual liquid phases of Mg and MgCl2. In this study, the process for titanium carbide production with composition close to stoichiometry and the minimum content of impurities was optimized with the various process parameters such as concentration of initial solution, its feeding rate and reaction temperature, as well as a kinetic study.

Jan 1, 2004

By D. Royston

Reducing SAG Mill feed size has been a major trend in recent years. ‘Mine to mill’ strategies have reduced blasted-rock size, and in a growing number of operations reducing the primary crusher CSS and/or adding additional crushing upstream of the SAG mill have reduced rock feed size. While reducing feed size will increase SAG mill throughput, issues arise in terms of retaining charge in the mill, exposing the shell lining to impact damage, and maintaining milling performance should the pre-crush system shut down. This paper reviews the past experience on pre-crushing for SAG mills and provides an analysis of liner design (in particular grates and shell liners) for pre-crushed feed.

Jan 1, 2012

By G. T. Fisher

A continuous process is used at Phelps Dodge Sierrita Inc. to produce copper sulfate pentahydrate via a solution extraction ? crystallization approach to supply the animal feed market. A review of the fundamental concepts of the process and unit operations is presented. Improvements in the process are aimed at achieving a controlled size distribution of product crystals (-40+80 mesh) with minimization of fines by primary nucleation and crystal breakage. An independent temperature control design was implemented for the heat transfer medium (water) in each crystallizer, albeit using common headers in and out of the chiller. This design was developed to maintain a controlled degree of supersaturation in each vessel while preventing localized spontaneous nucleation of fines and reducing encrustation of the heat transfer surfaces in each crystallizer. A model was developed to calculate the heat load and heat transfer coefficient of each crystallizer along with the saturation copper tenor as a function of temperature and free acid.

Jan 1, 2007

By Y. C. Kim

This paper discusses Air Liquide's patented SPALTM (Surface Protection Air Liquide) technology and process for the inerting of coreless induction furnaces using cryogenic liquid gas. Air Liquide Canada Inc., in collaboration with Riverside Brass and Aluminum Foundry Limited (Riverside Brass), conducted plant trials to demonstrate the applicability of the SPALTM technology for copper-based alloys. Results showed that with SPALTM, Riverside Brass benefited from a significant increase in metal yield as the level of dross formation was drastically reduced. Together with the many other benefits of this technology, SPALTM demonstrated to be a non-negligible cost-effective solution to reduce metal production costs. In an effort to optimize the argon flow, different flow rates were used and the oxygen level above the metal bath was measured to pinpoint optimal flow. The results of metal yield, charge mix, dross formation, and melt temperature are compared with and without argon. The metal yield improvements are dramatic and calculated net savings are presented hereunder.

Jan 1, 2007

By I. S. Laitinen

Outokumpu Technology has recently introduced new technology in both copper electrorefining and electrowinning. This technology includes, among other things, a new permanent cathode (Outokumpu Permanent Cathode) and new busbar technology (Outokumpu Double Contact System). The new technology has already been tested in commercial scale cells. To get a better understanding of the busbar system a multiphysical simulation model of the electrowinning and electrorefining cells was developed. A mathematical model of electrical conduction and heat transfer in a copper electrolysis cell was developed from partial differential equations. The model was expanded to a cell group including seven electrolysis cells connected electrically in series. The model was solved numerically using the finite element method (FEM). Using the model, different intercell busbar systems were simulated. Typical electrical disturbances, like loose contacts between cathodes and the main busbar and short circuits between electrodes, were included in the simulation. The results of the simulation runs with conclusions are presented in this paper.

Jan 1, 2007

By Steven Aiken

The East Boulder Mine located in Montana, U.S.A. utilizes snowmaking to assist with mine water treatment for nitrogen removal. Nitrogen species, including ammonia, are common contaminants in mine water from underground mining operations. Snowmaking provides secondary treatment of nitrogen during the winter due to the chemical and physical processes that occur during snowmaking, in the snow pack and in the snowmelt. The primary processes include atomization, evaporation, sublimation and volatilization. The snowmakers also provide secondary treatment for nitrogen removal when used as evaporators and/or land application units during the summer. In 2002, the snowmaking process was successful at reducing total nitrogen in the mine water by up to 87%. If additional losses due to soil and root zone processes are included, total nitrogen reduction would increase to between 87 and 97%. Snowmaking is an effective nitrogen reducing treatment method during the winter when other treatment methods such as land application cannot be used.

May 1, 2004

By M. Kalin

Tailings deposits are frequently the source of ground water contamination due to the transport of contaminated tailings pore-water. If amendments to tailings covers could be made to facilitate a precipitation reaction and halt or reduce the generation of acid in pyritic tailings, the quality of pore-water quality would be improved which would in turn reduce the production of contaminants. The effects of phosphate wastes, added to base-metal mine tailings in Newfoundland, Canada, were tested. Laboratory and field experiments determined the effects of different mixing ratios of phosphate wastes to tailings volume (1:4, 1:8, 1:12 and 1:20, dry weight) for a total period of 3.2 years. The addition of phosphate at ratios of 1:4 to 1:12 substantially increased the pore water pH, and reduced both acidity and Zn concentrations. These results suggest that addition of phosphate wastes to tailings covers can reduce acidity generation and improve tailings pore-water quality.

Jan 1, 2004

By T. Nagasaka, T. Miki

Suppression of CO2 and waste such as slags discharged from iron- and steelmaking processes are some of the typical major issues for the protection of global environment and sustainable growth of steelmaking industry. Utilization of active phytoplankton growth will be one of the best options to stabilize and suppress carbon dioxide at high-efficiency. Inorganic minerals such as C, 0, N, Si, P and Fe are necessary for phytoplankton multiplication. It is crucial for supply of nutrition into seawater effectively for phytoplankton multiplication to understand the dissolution behavior of some elements from steelmaking slags into seawater. The morphology of the precipitated phases in steelmaking slags during cooling period was investigated in the present work. The dissolution behavior of some elements from steelmaking slags into artificial seawater has also been studied. The effect of nutrient dissolved into seawater on phytoplankton multiplication, some examples of marine structure made from steelmaking slag, and estimation of CO2 fixation amount by marine phytoplankton are also discussed.

Jan 1, 2004

By M. A. Keogh

This paper reviews the physical properties that make low-density polyethylene the most practical and economical material for launder• fabrication in the majority of mine and mill applications. The basic design features and use of other launcher• materials are also discussed.

Jan 1, 1976

By Sadough vanini Ali

The silicon anisotropic wet chemical etching technique is widely employed for fabricating various microelectromechanical system (MEMS) structures for advantages such as simple etching equipment and its capability to fabricate special microstructures. In this paper, we consider a complete theoretical derivation of the analytical solution based on geometrical and kinetic aspects of step flow on any surface and with a mathematical method we derive new equation for calculating the microscopic etch rates of surface atoms for a new range of concentrations and temperatures. Furthermore, a novel equation is presented for the calculation of the microscopic activation energies for some typical surface atoms and a new comparison of activation energies between some atoms is made that divides atoms into three categories. The results demonstrate agreement with the experimental results.

Oct 1, 2011