Search Documents

By Ali Nasirian Ph. D., Gabriel Carvajal

To facilitate the safer and more secure transportation of inmates from San Diego Central Jail to the new San Diego Courthouse, the County of San Diego committed to building a new transfer facility as part of the downtown developments. The transfer facility includes a three-story underground structure adjacent and connected to the Central Jail and a 60-ft deep, 23-ft diameter, 320-ft long tunnel. The tunnel starts at County Jail, passes underneath Western Regional Detention Facility (Old Jail) and, ultimately, connects to the State Courthouse. Condon-Johnson & Associates, Inc. (CJA) was selected to install the temporary shoring shaft for the underground structure as well as three arrays of canopy pipes to support the tunnel’s Sequential Excavation Method (SEM) construction. CJA installed the rectangular 56-ft deep access shaft shoring with three levels of bracing, and a combination of secant piles, soldier piles, and timber lagging. The shoring also included a sliding bridge at top to provide access for trucks to enter and exit from county jail during the duration of construction. Following shoring and shaft excavation, CJA installed and grouted 7-5/8” dia. canopy pipes in 3 reaches, parallel to the longitudinal design line of tunnel with a slight lookout angle. CJA installed 24 each canopy pipes, 99-ft from face of shaft at reach 1, 21 each, 80-ft length canopy pipes at reach 2, and 21 each, 75-ft length pipes at reach 3. CJA confirmed canopy pipe alignment via Inertial Sensing Gyro. To mitigate the possibility of settlements caused by the tunneling operation underneath Old Jail strip footing and grade beams, CJA also performed void fill grouting. Sleeve port grout pipes (SPGP’s) were installed inside the Old Jail basement and grouted with the use of packers as the tunneling operation passed underneath the Old Jail. In detailing various aspects of the construction, this paper aims to magnify the innovative solutions for shoring, canopy pipe installation and void fill grouting challenges as well as the state of the art quality control measures undertaken by CJA.

Oct 1, 2022

By Dario Libano, Armando Caputo, Francisco Caputo

"UHE Peixe Angical is a 452 MW hydroelectric power plant located on the Tocantins River in Tocantins, Brazil. In 1999, geologists began feasibility studies to estimate the river’s hydroelectric potential, and the decision was made to proceed with the construction of a power plant. In 2002, after extensive investigation, the studies indicated geological homogeneity at the site for the dam, except for an anomaly detected on the left margin, and construction began on the $1.2 billion project.As the work began, the complex ground conditions presented several serious difficulties. The solution was unlike any undertaken before in Brazil— a 100-m-long secant cutoff wall, with 76 1.8-m-diameter piles of up to 78 m deep. All were placed in a six-month period.In the preparation for the detailed construction plans, further studies in the area of the anomaly better defined the geology so that a treatment program could be developed. The feasibility study had detected silicified rock with high permeability in one area, and an injection curtain was designed with five injection lines. In the other area with an anomaly, further investigation revealed a permeable marble formation that was 50 m thick. Here, a specific injection program with three injection lines was developed.The injections started in February 2005 in the marble formation area. By July of that year, only the primary and secondary holes were drilled from the three lines, resulting in a space between injections of 1.50 m. By the end of July, the drilling was halted. The contractor had identified a thick area of heterogeneous material below the transition zone that was characterized by a mixture of soil, fractured rock and hard fractured rock. The anomalies were detected while drilling, and both the general contractor and the designer concluded that the phenomenon of “piping” was taking place.Constructing a positive cutoff wall became a priority."

Jan 1, 2009

By Steni Stefani, Sanjay Dave

"This paper describes an innovative method, used for the first time in India, for the construction of a 1.0metre-thick positive plastic concrete cut-off wall (CoW) at the upstream toe of the dam at the Kishanganga Hydro-Electric Project in Jammu & Kashmir- India. The extremely difficult bouldery geology with an overburden laden with very hard Panjal Volcanics (quartz, feldspar, muscovite and chlorite minerals) boulders of up to 0.8m to 1.8 metres in size with UCS of up to 265 MPa and the requirement of socketing the CoW into the underlying hard bedrock (UCS 265 MPa) for 1.50m made the choice for the excavation methodology critically difficult. After having evaluated several other existing methods – including hydromill trenchers – the Civil Contractor Hindustan Construction Company, in agreement with its Foundations Engineering Consultant (Ricerca e Sviluppo – Cantieri e Gestioni) opted for a two-stage construction method: firstly, preliminary full-depth drilling and “surgical” blasting with full-length inclinometer checking of borehole verticality to ensure the exact location of rock fracturing and fragmentation coincided with the required position and that it was vertical, notwithstanding efficient trenching into the bedrock of a nominal 1m by 1.5m section; and, secondly, excavation by using heavy duty mechanical rope grabs made locally and developed by the Consultant in collaboration with the Contractor. The details of the methodology and the salient construction data is presented and commented for the 33-metre deep CoW installed at a working platform elevation of 2364.50 m above sea level in a very remote area.BACKGROUNDThe Kishanganga Hydro Electric Project (KGHEP) is a ROR (run-of-the-river) project is located on the Kishanganga River some 140kms North-West of Srinagar, capital of Jammu & Kashmir State of India, for generating 330MW of power in a 90% dependable annual year. The key components of the project are: Concrete Face Rockfill Dam (CFRD), Chute Spillway, Plastic Concrete Cut-off Wall (CoW), Head Race Tunnel (HRT), Surge Shaft (SS), Inclined Pressure Shaft (PS), underground Power House and Transformer Hall, Tail Race Tunnel (TRT).The Power House Site is accessible throughout the year from Srinagar while the remote Dam Site, with its tortuous road climbing the Rajdan Pass at 3556m (11,667 ft) above sea level and several 20-tonne capacity Bailey bridges removed prior to snowfall, remains inaccessible for around 4 months between mid-November to mid-May due to winter and heavy snowfall - the only access is by helicopter, weather permitting. Temperature at the Dam Site drops down to minus 27degrees Celsius during winter, therefore, careful planning from the beginning was most essential for the successful delivery of the Project.This paper deals with the Cut-Off Wall construction which was performed, for the first time in India, adopting a “Drilling and Surgical Blasting” method. However, this technology is not new and diaphragm wall excavation with the aid of drilling and blasting has already been done in some of the projects globally; namely:"

Jan 1, 2017

By Emad Farouz

This paper presents a case history of a successful construction-phase pile load test program that optimized the pile design in challenging ground conditions at the Great Neck Wastewater Treatment Plant in the Town of North Hempstead in Nassau County, New York. The improvements and expansion of the wastewater treatment plant included the construction of several new structures to comply with new stringent nitrogen discharge requirements and new design flow. The challenging ground conditions included up to 20-ft thick organic deposits with weight of hammer blow counts and up to 14 percent organic content and tidal ground water that was near the ground surface. The foundation design evaluated various deep foundation alternatives and selected driven closed-ended pipe piles then filled with concrete as the most suitable foundation. The selection process included considerations of cost, risk, vibrations, noise, and schedule. The contract documents utilized an innovative approach of performing an optimization load test program that was implemented during construction to optimize pile lengths and reduce potential vibration and construction schedule. This paper discusses the details of the successful load test program including static testing, dynamic testing, and the innovative contracting approach utilized to implement the construction phase load test program. It also discusses the successful development and implementation of driving criteria for production piles and construction challenges. The successful load test program resulted in savings of several hundred thousand dollars, optimized schedule, and lower environmental impacts.

By Bernard Hertlein, Chia K. Tan

"The move to LRFD methods for structural design by AASHTO, ACI, AISC , ASCE, and the FHWA has been a major change for the American construction industry. The deep foundations industry has arguably been placed most at risk by this situation, because of the need for, and the difficulty of providing, reliable quality assurance.LRFD is attractive for both the owner and the engineer because it promises cost reductions, but the assumption underlying LRFD is often overlooked - that the acceptable margin of safety can be rationally reduced, thus saving costs, provided that all the factors involved are closely controlled. This means that both the quality of the materials and the quality of the construction work must be closely monitored, and held to an acceptable standard.This paper describes the type of comprehensive quality management program that is needed in deep foundation construction projects based on LRFD. Case histories are used to illustrate the importance of both adequate inspection and reliable testing to a comprehensive quality management program.IntroductionOver the last thirty years, the major organizations that set standards and practice policies for the American construction industry, such as the American Association of State Highway and Transportation officials (AASHTO), the American Concrete Institute (ACI) , The American Institute for Steel Construction (AISC), the American Society of Civil Engineers (ASCE), and the Federal Highway Administration (FHWA), have embraced Load and Resistance Factor Design (LRFD) as an alternative to, and in some cases, a complete replacement for, Allowable Stress Design (ASD). AASHTO first published a new set of LRFD-based design guidelines for bridges in 1996, with several revisions in 1997, 1998, and 1999 (AASHTO, 1996). The 1996 AASHTO Bridge Design Code was the first in the United States that required foundations to be designed using LRFD procedures. LRFD has a clear advantage over conventional ASD where variability in material strength, bias in design methodology, and degree of construction quality can be rationally accounted for to achieve an acceptable level of risk."

Jan 1, 2005

By Eric S. Lindquist

Two microtunnel access shafts were constructed using the Cutter Soil Mixing (CSM) method in the San Joaquin Delta region of California, east of San Francisco. Unlike conventional slurry walls and diaphragm walls that utilize concrete, soil mixing relies on blending the soils in situ with a cement slurry to create a soil-cement wall. Cutter Soil Mixing technology utilizes two sets of vertically mounted cutting wheels rotating about a horizontal axis to produce rectangular panels of treated soil. Overlapping of the soil mixed panels enabled the construction of two circular shafts. CSM panels were constructed to a depth of 29 m (95 ft) for the microtunnel jacking shaft and to a depth of 19 m (63 ft) for the microtunnel receiving shaft. The site presented several challenges, including the high depth of treatment, the variable nature of the alluvial soils, and the high water table. This paper describes the CSM technique and presents the design, construction, quality control measures and advantages of using this method for this project.

Jan 1, 2010

By Craig H. Olson

"Anew ship dock at a Philadelphia area refinery will be capable of docking the largest tanker to travel the Delaware River, the Stena V-MAX, which will induce significant lateral loads. The loads at the dock, a system of mooring dolphins and platforms, will be resisted by over 150 pipe piles, including some 20- and 30-in diameter, reinforced, concrete-filled pipe piles and H-piles. Construction included driving the pipe piles to the required ultimate capacity, flushing the pipe pile casing clean of overburden materials, followed by drilling rock sockets into the underlying Wissahickon Formation. The Wissahickon Formation is a complex subsurface that includes variations in depth to bedrock, rock quality, degree of weathering and the presence of very hard quartzite lenses or inclusions. Because of the problematic subsurface, the designers and client requested extensive pile dynamic analysis (PDA) testing by TRC Engineers (TRC).Before beginning, the contractor requested that TRC perform the WEAP (wave equation analysis program) to evaluate the proposed hammer (APE D30-32 open-end diesel) to drive the piles into the proposed bearing strata while maintaining allowable compression stress levels. The WEAP provided a prediction of blow counts and stresses for various ultimate capacities, and showed that for the HP14x89 piles with a required ultimate capacity of 480 kips, a blow count of at least four blows per in at a stroke of 8.0 ft was necessary. New Approachway RampThe PDA testing began at the new dock approach way ramp, parallel to the existing one. The new structure is a 300-ft-long by 21- ft-wide concrete deck supported on seven bents; each has two 24- ft-diameter steel open-ended pipe piles. Every pipe received an HP 14 x 89 x 80-ft pile that was later driven beyond the pipe pile tip to create a composite pile. The pipe piles were later cleaned of overburden materials and finally filled with concrete and rebar. At each bent, a cap was installed on top of each pair of pipe piles, and then a prefabricated concrete deck was added."

Jan 1, 2008

By Craig H. Olson

"A new ship dock at a Philadelphia area refinery will be capable of docking the largest tanker to travel the Delaware River, the Stena V-MAX, which will induce significant lateral loads. The loads at the dock, a system of mooring dolphins and platforms, will be resisted by over 150 pipe piles, including some 20- and 30-in diameter, reinforced, concrete-filled pipe piles and H-piles. Construction included driving the pipe piles to the required ultimate capacity, flushing the pipe pile casing clean of overburden materials, followed by drilling rock sockets into the underlying Wissahickon Formation. The Wissahickon Formation is a complex subsurface that includes variations in depth to bedrock, rock quality, degree of weathering and the presence of very hard quartzite lenses or inclusions. Because of the problematic subsurface, the designers and client requested extensive pile dynamic analysis (PDA) testing by TRC Engineers (TRC).Before beginning, the contractor requested that TRC perform the WEAP (wave equation analysis program) to evaluate the proposed hammer (APE D30-32 open-end diesel) to drive the piles into the proposed bearing strata while maintaining allowable compression stress levels. The WEAP provided a prediction of blow counts and stresses for various ultimate capacities, and showed that for the HP14x89 piles with a required ultimate capacity of 480 kips, a blow count of at least four blows per in at a stroke of 8.0 ft was necessary.New Approachway RampThe PDA testing began at the new dock approachway ramp, parallel to the existing one. The new structure is a 300-ft-long by 21- ft-wide concrete deck supported on seven bents; each has two 24- ft-diameter steel open-ended pipe piles. Every pipe received an HP 14 x 89 x 80-ft pile that was later driven beyond the pipe pile tip to create a composite pile. The pipe piles were later cleaned of overburden materials and finally filled with concrete and rebar. At each bent, a cap was installed on top of each pair of pipe piles, and then a prefabricated concrete deck was added."

Jan 1, 2008

By Yan Lap J. Kan

"A waterfront stabilization system consisting of Deep Soil Mixing (DSM) columns, vinyl sheet pile fascia, and concrete flood walls supported on shallow footings was designed and constructed for a high-density waterfront development in Northern California. The project site is underlain by soft, compressible organic soil locally known as Bay Mud that has been capped with loose sand and imported fill. The waterfront stabilization system constructed at the site mitigates liquefaction, consolidation settlement and seismic potential slope deformation along the waterfront; the system was designed to reduce lateral displacements to tolerable amounts for the proposed structures. This paper presents the general design methodologies, construction challenges and quality control of this waterfront stabilization system.INTRODUCTIONUrban development in Northern California is fueling innovations in geotechnical engineering as more complex sites are developed. ENGEO Incorporated introduced a deep soil mixing technology from Japan to the US and designed a waterfront stabilization system for a high density waterfront development project in Redwood City, California. The approximately 12½-acre project site, as shown on Fig. 1, is surrounded by water on three sides, with an inner marina at the center of the site.The project site is located in the seismically active San Francisco Bay Area in California. The San Andreas Fault, the Monte Vista-Shannon Fault, the Hayward Fault and the San Gregorio Fault are major active faults located within 25 miles of the site. Once a former marshland with a major slough until the late 1950s, the site was reclaimed by placing imported fill over the native compressible clay deposits, locally known as Bay Mud."

Jan 1, 2016

By Moonkyung Chung

Static pile load tests were performed in order to evaluate bearing capacities and mechanical behaviors of three different pile types: (1) steel-concrete composite drilled shaft with rebar reinforcements inside the concrete, (2) steel-concrete composite drilled shaft without rebar, and (3) conventional drilled shaft (reinforcement concrete pile). The material elastic moduli obtained from pile load tests of steel-concrete composite drilled shafts with and without rebar reinforcement were found out to be similar. On the other hand, the elastic modulus of steel-concrete composite drilled shafts is almost twice as high as that of the conventional drilled shaft. The ultimate strengths of the steel-concrete composite drilled shaft with rebar, the steel-concrete composite drilled shaft without rebar, and the conventional drilled shaft were 9,810, 7,848, and 4,414kN, respectively. The results of these load tests reveal that the ultimate strengths of the steel-concrete composite drilled shaft with reinforcement and that without reinforcement are 2.22 times and 1.78 times greater that that of the drilled shaft. The structural failures of the steel-concrete composite drilled shafts occurred either at the boundary between tip of steel casing and rock-socketed concrete.

Jan 1, 2010

By Meeok Kim, Paul Beljan, Gordon Chen

"Clinton combined sewer overflow storage (CSO) facility project developed by the Department of Water Environment Protection of Onondaga County, New York, is to improve sewer facilities and infrastructure in Syracuse, New York. The below grade facility will provide a storage of untreated stormwater during highflow periods to be treated later, thus reducing CSO discharges to Onondaga Creek.The CSO system consists of three parallel storage tunnels and two end chambers (west and east chambers) as main underground structure. The storage tunnels are about 850 ft. long, 55 ft. wide, 24 ft tall and located 20 ft deep below grade. The chambers, include above access and operation structure, are about 40 to 55 ft. deep and approximately 60 to 100 ft. wide.Kiewit Infrastructure and Weidlinger Associates Inc. developed an alternative approach for the tunnels to meet the facility completion schedule, strict design guide lines and quality control as an environmental and water tight concrete structure for the project. The original design anticipated use of a TBM machine to bore three parallel tunnels between two previously constructed chambers.The alternative design used a three barrel culvert cast-in-place structure in a cut and cover excavation supported by a soil bentonite wall. The SOE along the jet grouted bottom seal provided a ground water cut off as well.The SOE system is specially designed to enhance the quality of culvert CIP structure construction by providing enough space for a full height construction. Also it further reduces the construction time by having the less squarefootage of jet grout installation. The design of tunnel systems is accomplished effectively through the utilization of soil structure interaction using a finite element methodIntroductionTo avoid construction of an additional treatment plant to handle increases in combined sewage flows, the Department of Water Environment Protection of Onondaga opted to construct the Clinton combined sewer overflow storage (CSO) facility.The Clinton CSO facility provides an environmental friendly mitigation method for combined sewer overflows on Onondaga lake which is located in northwest of Syracuse."

Jan 1, 2015

By Phillip E. Glogowski, N. Catherine Bazan-Arias

Steel foundations can be designed to cross-sectional configurations ranging from triangular and square to other multi-side shapes. Adding lateral extensions (hereby called wings) along the length of the steel stem can increase the foundation’s uplift, torsional and lateral load capacities. DiGioia Gray staff developed a methodology for the optimal design for multi-facetted, winged deep steel foundations. A finite element (FE) model is used to represent the steel components and the nonlinear subsurface behavior. The geometry of the foundation can be complex; thus, an optimal design needs to be fine-tuned to the specific site conditions. We created a pre-processor tool to generate the FE model including varying values for the number and size of wings, depths of embedment, reveal/stickup heights, top plate geometries, and subsurface profiles. The analytical model has been partially validated through full-scale testing and the methodology has been applied to two installed projects to date.

Sep 8, 2021

By Jeff Jackson, Paul Axtell, David Graham

The Montana Department of Transportation recently awarded a contract to construct a replacement bridge across the Clark Fork River in Heron, MT. Both abutments and both intermediate bridge bents were to be founded on 6-ft and 8-ft diameter, permanently cased drilled shafts with rock sockets, respectively. Two drilled shafts per substructure location were designed for a total of eight drilled shafts. The original design included 6-ft diameter drilled shafts at the abutments but the Contractor elected to submit a Value Engineering proposal that increased them to 8-ft diameter. On the basis of the subsurface exploration program, extremely challenging subsurface conditions were known to exist, including the potential presence of large boulders within the predominantly sand and gravel soil matrix. The successful bidder elected to use an oscillator to install the permanent casing to the top of bedrock, while simultaneously removing the spoils from inside the casing with a clam-grab. On seven of the eight shafts, this approach worked well. Unfortunately, on one of the shafts, the casing met refusal on one or more boulders encountered in the predominantly sand and gravel soil overburden. Following several attempts, and despite several variations of approaches, it was determined that the casing could not be advanced beyond the obstruction without unacceptable risks to the pile-supported temporary work trestle (i.e., loss of soil and reduction in pile capacity for the foundations supporting the work trestle). To mitigate the problematic drilled shaft, a unique solution was designed and successfully constructed. The solution involved the construction of seven 16-in diameter micropiles constructed within the confines of the obstructed casing. The micropiles were drilled to bedrock through the sand, gravel, and boulders and include rock sockets to satisfy axial design requirements. The micropile casing thickness, grade and grout strength were designed to provide adequate flexural strength as well as to satisfy other design requirements. Upon completion of the micropile installation, the upper portion of the drilled shaft above the boulders and within the permanent casing was constructed as usual. This paper discusses the difficult subsurface conditions at the site, the drilled shaft construction difficulties, and the design and construction of the micropile solution.

Jan 1, 2018

By Rolf Katzenbach

Construction of drilled shaft foundations with the use of hydraulic oscillators and rotators to install temporary casing over the full depth of the shaft is described. The equipment and techniques were developed in the 1960?s in Germany and full-depth casing is now the predominant method of construction in Europe. Its use in North America is increasing. This paper presents an overview of full-depth casing methods and a summary of available load test data evaluated by the authors to compare the load transfer and capacity performance of shafts installed by various construction methods. Results demonstrate that load transfer and capacity of full-depth casing shafts are equal to or exceed that of shafts constructed by dry or slurry methods and that measured capacities are consistent with generally accepted design equations. The principal advantage of full-depth casing methods over other installation techniques is that the risk of defects in the shaft is minimized. Casing is able to penetrate into the ground under any geologic or groundwater condition when this technique is applied. Potential delays and cost overruns can thus be avoided and a safe, economical foundation element is created.

Jan 1, 2007

By Jeongbok Seo

The Dulles Corridor Metrorail Project (DCMP) involves the design and construction of a 23.1-mile extension of the Washington Metropolitan Area Transit Authority (WMATA) rail system. The initial 11.7-mile extension, with five transit stations and a new service and inspection yard, is to be constructed. The construction plan for the initial 11.7-mile extension includes installation of a total of an estimated 4,250 or 160,000 linear feet of driven 12x53 steel H-Piles at more than 80 different locations. At the time of this paper, approximately 40 percent of the piles have been installed and the remainder of piles will be installed by the end of 2010. This paper describes: 1) subsurface investigation program, 2) application of existing Codes and impact on the design of H-Pile, 3) design methods to determine geotechnical bearing capacity and pile tip elevation, 4) verification of capacity including PDA and Static Load Tests, 5) project specific pile load tests, and 6) QA/QC during pile driving.

Jan 1, 2010

By N. Shariatmadari

Two dry docks are currently under construction on the northern banks of the Persian Gulf by Iran Shipyard and Offshore Industries Co. (ISOICO). The construction of these dry docks forms a huge civil offshore project. The foundation system include more than 6500 large diameter (40-48 inch) spiral pipe piles with embedded depth varying from 18 to 25 meters. Extensive geotechnical subsurface investigations were carried out in the project site in order to provide enough information and proper perspective on the underlying soil layers. The results of geotechnical investigation indicated that a 20 m thick dense silty sand layer exist which can be considered as the main bearing stratum. Due to short clear distance between the piles (less than 3 m) refusal occurred for some piles, accordingly led to actual length less than their design length. To verify and in-situ evaluation of piles capacity, static and dynamic full scale loading tests programme were performed. The data from 40 static compression and tension and also 50 dynamic tests with PDA were interpreted and analyzed by current approaches and CAPWAP software. The results of analysis demonstrated that the safety factor of bearing capacity of piles must be increased to reach a safety factor of about 1.8. To achieve this purpose the interaction of combined piled-raft system has been realized.

Jan 1, 2007

By Shuvranshu K. Rout, Anup K. Mandal, Biswajit Das, Manos De

"To adopt new technology advancement in Steel Plant, there is a requirement of shifting of operation process from Coke Wet Quenching (CWQ) to Coke Dry Quenching (CDQ). New CDQ chamber foundation with deep basement and underground conveyor tunnel are to be constructed in an operating plant where heavy foundations and structures are located in close proximity. Furthermore, the existing CWQ system will be in operation during new underground construction and erection. Challenges to deep excavation of tunnel and chamber foundation consist of non-uniform ground condition, prevent washing out of soil from bottom of existing foundations, stability of existing nearby structures, presence of large number of underground utilities, ensuring safe underground workplace to construction resources engaged in new construction work along with project schedule and budget constraints. A combination methods involving use of soil nailing, soil grouting, contiguous bored pile and micro pile had been adopted for protection of excavation sides as well as existing structures. Each side of excavation in different stretches were analysed during design as well as construction stages. The use of combination of all techniques in a single brown field project in context of the nature of site constraints and safety issues made this a unique project.INTRODUCTIONSteel Industry is one of the backbones of industrial growth of any developing country like India. Due to increasing land prices most of the steel plants in India are expanding within their existing plant facilities. In addition to that, there is demand of adoption of new technology for future expansion projects to set new benchmarks with global standards.The property owner had earlier installed a Coke Wet Quenching (CWQ) for their Coke Plant. Now, there is a requirement from process department to proceed with Coke Dry Quenching (CDQ). To facilitate the CDQ within the existing CWQ which will be in operation is the main challenge for the property owner. The second challenge is the limited space for underground construction and subsequent equipment erection within the stipulated time frame.From a geotechnical prospective, the project team had uncertainty and reservations in their mind about the construction methodology. Therefore, the role of three “C”: ‘Consultant’-‘Client’- ‘Contractor’ and their combining brainstorming is essential to freeze a working plan for achieving the goal. In this paper, only the excavation support systems for underground foundation structures have been highlighted in the context of solving geotechnical problems."

Jan 1, 2017

By Arash Khosravifar, Matt Steffan

An expansion of the City of Klamath Falls Wastewater Treatment plant required geotechnical seismic hazard evaluations and deep foundation design. The site is located on the shore of Lake Ewauna and is underlain by diatom rich lake deposits. Diatomaceous soils exhibit unique engineering properties that are not well understood. Cyclic Direct Simple Shear (CDSS) testing was performed on three undisturbed samples to evaluate cyclic and post-cyclic properties of the diatomaceous soils. Results from the CDSS testing indicated that the soils would not liquefy in the classical sense, though cyclic softening behavior was observed. The CDSS results were used to develop a Cyclic Resistance Ratio curve for the diatomaceous soil to compare with clean sand liquefaction curves. Seismic lateral pile capacities were developed using two approaches. One approach used conventional p-multipliers for liquefied soil and modified them to reflect expected excess pore pressure ratios. The other approach applied residual strength and fifty percent strain values from post-cyclic monotonic shear testing. A lateral spread hazard zone was identified along the Lake shoreline and reduced, seismic lateral pile capacities were recommended. The objective of this paper is to report the seismic design considerations for this project in a unique geologic and seismic setting. INTRODUCTION The engineering properties of diatomaceous soils have rarely been studied and the cyclic behavior under seismic loading is generally unknown. Some of the critical geotechnical uncertainties of diatomaceous behavior include potential for large consolidation settlement, influence of irrecoverable strains due to diatom particle crushing, shear strength (peak and residual), and cyclic properties. This paper presents results of cyclic shear testing, seismic evaluations and seismic lateral pile design in diatomaceous soils performed for the expansion of a waste water treatment plant in the city of Klamath Falls, Oregon, site of the largest recorded earthquake in Oregon’s history. The expansion consisted of adding six new facilities at the existing Plant including influent pump station (IPS) and headworks, aeration basin, tertiary treatment, and other buildings. The IPS/headworks and aeration basin will be founded approximately 15 feet below ground. The other buildings will be founded at grade. The existing facilities are supported by timber piles that penetrate the surficial diatomaceous soils and terminate on a hard underlying deposit. Figure 1 shows the site plan and proposed additions.

Jan 1, 2018

By Kazuyuki Matsuzawa

A series of plate loading tests were carried out on a loam ground in order to investigate the influences of the plate size and the loading rate on the observed load-settlement relations. Two circular plates having diameters of 0.3 m and 1.0 m were used. Three types of loading methods were employed; 1) static cyclic maintained load test, 2) static continuous load test, and 3) rapid (dynamic) plate load test. An interpretation method called non-linear damping method was used to estimate a static load-settlement relation from the rapid plate load test signals. The derived static load-settlement relations match well with the measured results from the static load tests.

Jan 1, 2006

By Nabil F. Ismael

The axial capacity of step tapered bored piles in sand was examined by field tests at one site in Kuwait. Two straight piles, and two step tapered piles were load tested in compression to failure. All four piles were 3 m deep. The straight piles were 0.2 m in diameter. The step tapered piles had a diameter of 0.3 m for the upper segment which extended up to 40% of the pile length changing to 0.2 m diameter for the lower section. The soil profile consists of medium to dense sand with minor cementation and no groundwater was encountered. Both the ultimate bearing capacity and the settlement at working loads were examined. The axial capacity of the step tapered piles was greater, and the settlement at working loads was less, compared with the straight shaft piles. The increase in capacity is mainly attributed to the added side friction along the larger diameter top segment of the shaft.

Jan 1, 2008