Search Documents

By A. Y. Senchenko, S. G. Rybkin, A. V. Aksenov

"Oxidized nickel ores are important source for nickel production in Russia. Considerable explored reserves of oxidized nickel ores with relatively low nickel content, about 0.6-1.4%, are concentrated in the Ural region of Russia. Conventional process flowsheet with the use of blast matte smelting, applied in particularly by JSC “Ufaleynickel”, proves itself as extremely low-margin technology. This paper will examine development of a new more cost-efficient process involving integrated treatment of oxidized nickel ores using the ore from Serovskoye deposit as an example. Target products of this process are hydrate residues containing up to 15 % of nickel and 0.3 % of cobalt, as well as saleable salts of magnesium sulphate and ammonium suplphate. This innovative process includes roasting of a mixture composed of ground ore and sulphuric acid at 650 °?. Sulphate roasted product is then leached in a weak sulphuric acid solution with the following separation of liquid from insoluble solids. Sulphate solution is neutralized by aqua ammonia in two stages until media pH is 3.0-3.5 and 7.5-8.0 with detachment of iron- and nickel-bearing hydrate residues respectively. The mother solution is boiled out resulting in salt crystals which are then dried and roasted at 500-600 °? to obtain magnesium sulphate. The gases generated during salts roasting are captured with production of ammonium sulphate. The developed technology demonstrates higher potential in terms of its economics and eco-efficiency comparing with the conventional process. This innovative technology for integrated process of oxidized nickel ores was patented in Russia.INTRODUCTION Development and industrial implementation of efficient technologies to process oxidized nickel ores is a very important task for non-ferrous metallurgy of Russia. The main reasons for the required technical upgrade of the plants processing oxidized nickel ores is depletion of rich ores, increase of energy resources costs, amplification of environmental and production standards. Due to this, transition from conventional pyrometallurgy to cost-effective hydrometallurgical technologies of ore liberation and solutions processing is logical and corresponds to the worldwide practice of Ni production from oxidized nickel ores."

Jan 1, 2018

By G. J. Feng

Based on detailed theoretical analysis of coarse floatation and three-phase froth, a laboratory system which contains a new type of froth floatation equipment is established. Through water experiment, the relationship among floatation dynamics parameters of the equipment is studied and the best work parameters are educed too. Based on all of above, Slurry test is carried out in a copper concentration plant. Granule between 0.28~0.45mm can be reclaimed successfully. The slurry test proves that to separate coarse minerals in froth floatation equipment is a kind of effective method, it is well worth to make a further study.

Jan 1, 2014

By I. Gombköto

To sustain the growth of industrial production necessitates the increasing of the amount of processed mined raw and secondary materials. As a side effect of raw material production, the amount of tailings material, - coming from mineral processing operations ? increases as well. Using wet technology, these tailing materials are generally transported and stored with the water used for previous operations. This habit could lead to dangerous situations. Enough to remember the disasters had happened to the last decade, safe tailings operations need to remove as much water from the solid as possible. Environmental, technical and economical needs should meet, therefore using a technology combining these specific needs could be necessary. Paste technology was introduced generally into tailings operations at the last ten years, as an answer to the call of the above mentioned challenges, however there are still many questions to answer within the frame of using it. The Institute of Raw Materials Processing and Environmental Process Engineering of the University of Miskolc has been dealing with mechanical process engineering, especially by the support of the EU project TAILSAFE Contract nº EVG1-CT-2002-0066 and the NKFP 3A/068/2004 Hungarian fund extensive research has been carried out about paste technology. Different test methods and materials were applied. Tested tailings materials were as follows: different fly ashes from coal power plants from Pécs ? Hungary, Gyöngyös ? Hungary, Neyvil ? India, different Croatian ashes, hazardous waste incineration plant ashes from Dorog ? Hungary, different kind of sands from Hungary, fine glass sand from Fehérvárcsúrgó ? Hungary, flotation ore processing tailing from Gyöngyösoroszi ? Hungary. Different additives, as gypsum, bentonite and cement were tested as well. The applied test methods were as follows: physical material testing (laser sizer, piknometer, different microscopes), X-ray diffraction analysis, settling columns, the three measuring pipes tube viscometer (16~27 mm pipe diameter), a hydraulic test loop with different pumps (40~53 mm pipe diameter, 0.2~4 m/s average slurry velocity range, 0%~52 % volumetric concentration range), rotational viscometer, Cassagrande yield locus tester and the slump cone test. This paper summarizes and systematizes the results of the aforementioned research as well as reports about the developed paste pipe transport design method based on the fine suspension ? coarse mixture model. The paper also reports about a systematic experimental series with different materials to establish criteria when high concentration suspensions behave like paste.

Jan 1, 2014

By Li Tianxia, Zhou Jing, Zhu Yimin

"A typical low-grade of high sulfur bauxite fr contains 54.71% Al2O3, 11.35% SiO2 while the ratio of aluminum and silicon was 4.25, and harmful components such as Fe and S graded 7.3% and 1.33% respectively. The ore is characterized by complex mineral compositions, fine dissemination of particle size of pyrite and diaspore, low desulfurization efficiency, and difficult separation of aluminum and silicon. In order to improve the degree of concentration, recovery and desulfurization efficiency on the basis of process mineralogy studies, the floatation behavior of high sulfur bauxite in the process of desulfurization and desilication were studied through laboratory tests and pilot plant tests. KEYWORDS high-sulfur bauxite; low grade; flotation; desulfurization;desilicication INTRODUCTION In order to solve the selection problem of bauxite mine area, we carried out technological mineralogy, laboratory test, small-expansion Dalian test to solve the problem of the refractory ore. Main research contents and conclusions were presented as followings :(1)Process mineralogy research shows: the main mineral components include diaspore, kaolinite, chlorite, pyrite, limonite. (2)Batch flotation tests indicated that slime can be dispersed well during desulfurization floatation when Na2CO3 was used as modifying agent. (3)Poilot plant tests shows that Batch flotation tests results are correct. 2?PROCESS MINERALOGY 2.1 Chemical Composition of Ore 2.1.1 Spectral Analysis of Sample The results of the semi-quantitative analysis of X-Ray -fluorescence spectra of the original ore are shown in Table 2-1. The results of spectral analysis show that the main components of the sample are O, Al, Si, followed by Fe, Mg, Ti, S and so on, while the content of other elements is very small. The value is Al, and maybe Ti, for bauxite, while Fe and S are unfavorable elements, and Si and Mg and Ca are the main impurity elements."

Jan 1, 2018

By Jia Ma, Lu-De Qiang, Zhi-Chao Liu, Chun-Feng Li, Guang Li, Bao-Bin Tang

"At present, research on the surface chemical properties of uranium minerals is very scanty, which restricts the research progress of uranium ore flotation process research. The research aimed at exploring the surface characteristics of two common uranium minerals and providing basis for flotation process to enrich uranium minerals in ore. This paper selected pitchblende and uraninite as the object of study, which are widely distributed in uranium deposits. We chose out the pure minerals of pitchblende and uraninite from different ores collected from different uranium deposits. By means of Zeta potential test and X-ray photoelectron spectroscopy (XPS) test, a preliminary study on surface characteristics of the pure minerals of pitchblende and uraninite was conducted. And the significance of the change of Zeta potential, the elements composition and valence state on the minerals surface for flotation was discussed. The research shows that, the Zeta potentials of pitchblende and uraninite in pure water are negative mainly when the pH value varies from 2 to 11, which maybe a result of the difference of ionization capacity between two kinds of oxy-compounds on the surface of minerals. On the surface of pitchblende and uraninite, the metal elements are mainly U, Th and Pb. U is mainly in the form of UO2, Th is mainly in the form of ThO2, and Pb is mainly in the form of Pb and PbO. Based on the surface characteristics of pitchblende and uraninite, we can select process and reagents appropriately in uranium ore flotation.INTRODUCTION Globally, the major challenges associated with exploitation of low grade ores are about finding economically feasible processes for reducing the mass of gangue minerals (Filippov et al., 2012). Among the beneficiation technologies of low grade uranium ores with complex minerals assemblage, flotation is the common process which is used to reduce production cost and eliminate the acid-consuming minerals (Li et al., 2016; Liu et al., 2015)."

Jan 1, 2018

By Bern Klein, Givemore Sakuhuni

Flotation is the dominant base metal extraction technique and it requires ore to be ground below the liberation size for effective recovery due to its dependence on mineral surface properties. For a poly-metallic ore, differential hardness of constituent minerals leads to over grinding of softer minerals before the harder minerals are fully liberated, which makes selection of a target grind size complex, and the complexity increases when treating leaner ores. Flotation recovery deteriorates above 100 and below 10 microns causing significant loses of valuable minerals in most flotation circuits. Although enhanced gravity concentration is known to be effective at recovering particles above 100 microns, which are difficult to hydro-dynamically transport, exploiting differential specific gravity for base metal separation was not an option in the past. This was partly due to the absence of high mass yield gravity techniques. The advent of continuous gravity concentrators with flexible mass yields, in the past two decades, has necessitated investigation of possible base metal applications. The Knelson CVD, one of the continuous discharge centrifugal concentrators, has an established application niche for sulphides associated with gold. However, its base metal applications have never been rigorously tested. Considering the dependence of flotation recovery on particle size, continuous discharge centrifugal concentration can be integrated in flotation circuits to capture flotation non-recoverable coarse particles. This paper explores how particle size, liberation and mineral hardness influence application of continuous centrifugal technology to regulate galena deportment in a polymetallic base metal plant. The results show that particle size affects galena recovery more than liberation. In view of these results, the CVD can be integrated in the primary grinding circuit to pre-concentrate the heavy sulphides at a coarser grind size with potential grinding energy savings.

Jan 1, 2014

By Silvia França, Hudson Couto

"In this paper, an alternative beneficiation process was developed to recover nickel minerals from low-grade weathered ores. The studied sample, 0.3% Ni grade, is essentially composed of nickel sulfides (pyrrhotite and pentlandite); magnetite and silicates (mostly talc and amphibolites) are the primary gangue minerals. The particle size distribution was controlled using a grinding operation to avoid producing an excess of fine particles by overgrinding. The sample underwent a grinding step for the fine degree of liberation. The slimes (-20 ?m) were removed via two desliming stages in hydrocyclones (diameters of 1.5" and 2"); the ground material, which was classified in a range of (-150+20) ?m, was processed by column flotation in three different stages: rougher flotation for magnesium silicates, rougher flotation for sulfides, and cleaner flotation for sulfides, using pilot flotation columns (2" and 6" in diameter and 20 ft high). The goal of using the preliminary magnesium silicate flotation step was to remove hydrophobic minerals (mostly talc) that would float naturally with the sulfides, which would decrease the Ni grade in the concentrate, as well as to reduce the MgO content because this compound is considered harmful in metallurgical processes when a grade greater than 9% is used. The final concentrate obtained in the cleaner flotation step reached up to 2% Ni and 7.0% MgO. The global and flotation recoveries in the process were approximately 30% and 60%, respectively, due to the losses of Ni during the desliming process. Despite this low global recovery, the adopted beneficiation process can be considered an interesting alternative to produce nickel concentrate from tailings or waste materials."

Jan 1, 2014

By G. Mucsi, F. Kristály, Á. Rácz, É. Gregus, K. Bohács

"Stirred media mills are widely used in the industry for fine grinding. Most of the applications work in wet mode, however dry grinding in stirred media mill comes forward more frequently nowadays. The present paper deals with the differences and similarities of the wet and dry grinding in stirred media mill from energetic and mechanochemical point of view as well. Grinding experiments in batch stirred media mill were carried out with different materials. During the experiments zeolite and kaolin were used as feed material. The grinding experiments were carried out at different stress energy and stress number values; the grinding work was measured during milling. After grinding X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), particles size analyzes by laser scattering were carried out on the ground materials. As a result of the systematic grinding and analytical measurements a comprehensive comparison was carried out on the wet and dry grinding and their usefulness for mechanical activation in stirred media mill. INTRODUCTION The natural zeolites are crystalline hydrated aluminosilicates of alkali and alkaline earth characterized by the structure that contains frameworks responsible for the high cation exchange capacity (CEC) and absorption capacity. The frameworks are interconnected by cavities and resided by cations variable in size, coordinated by water molecules. Since zeolite comprises SiO4 and AlO4 tetrahedra interlocked by oxygen atoms that are situated in the structural nodes, their characteristics differ due to the varieties in the structure-directing agents and Si/Al ratio (Colella and Wise, 2014; Malekian et al., 2011; Terzic et al., 2017). The most common natural zeolite occurring in high amount, of industrial importance and involved in milling and MA is the clinoptilolite, in the literature equivalent to “natural zeolite” designated for high clinoptilolite bearing volcanic tuffs. Its amount in the host rock must reach ~ 40 % by weight to obtain the CEC and adsorption desired in its applications. In the highest quality rock might reach 80-90 % by weight (Favvas et al., 2016), but most often is the 40-60 % by weight content, associated with smectites, improving the CEC and adsorption of the tuffaceous rock. The application of such natural zeolites is problematic in many cases due to high silica (quartz, cristobalite and volcanic glass) content and beneficiation (concentration and extraction of pure zeolite) are not feasible. Thus, mechanical activation is a possible way to alter the other than clinoptilolite minerals generating high specific surface area and functionalized particle surfaces to enhance adsorption, reaction or particle adhesion. The zeolites easy availability and the utilization cost-effectiveness have prompted the research on their physicochemical and structural properties (e.g. adsorptive and molecular-sieve activity, heat resistance, and microporous cage structure) and finding new options for their application (Kusuma et al., 2013; Musyoka et al., 2014; Rida et al., 2013; Terzic et al., 2015b). Apart from the presence of exchangeable framework cations which are crucial for the adsorption ability, and a certain degree of pozzolanic reactivity. The thermal stability of dehydrated phases is another important characteristic for use of the zeolite in composite materials that are exposed to high temperature. Thereby, the zeolites found a wide application possibility in the design of the construction composites (Albayrak et al., 2007; Najimi et al., 2012; Vejmelková et al., 2015), as well as for resolving of the environmental protection issues like wastewater refining or heavy metal elimination (Gómez-Hortigüela et al., 2014) even from contaminated groundwater using passive methods like permeable reactive barriers (Gombköto et al, 2016). The grinding treatment of zeolite is a common and frequently applied procedure, both on laboratory (Bohács et al. 2017, Faitli and Czél, 2014)"

Jan 1, 2018

By J. Temuujin

Mongolia has some of the world?s largest coal reserves with an estimated total coal reserve of over 150 billion tonnes. At present, over 90% of Mongolian electricity is produced by combined heat and thermal power stations. The main coal deposits used for Central power system's power stations are Baganuur, Shivee-ovoo lignite type coal and Shariin gol bituminous coal. In Mongolia almost 600,000 tonnes of coal combustion by-products are disposed of in waste ponds. In this research, we have thoroughly characterized Mongolian coal combustion by-products including fly ashes sourced directly from thermal power stations and ash retrieved from ponds. It was determined that fly ashes generated from Baganuur and Shivee-ovoo coal deposits are class C, while ash from Shariin gol coal is class F (according the ASTM C618). All ash products were characterized by chemical, mineralogical, granulometrical, porosity, FE-SEM and radiation methods. Fly ashes sourced directly from power stations were found to be more suitable for manufacture of geopolymers for building materials application and zeolite synthesis than ashes retrieved from ash ponds. The adsorption and porous properties of zeolitic compounds were measured and found to be suitable for adsorption of Cr6+ from simulated tannery waste water. Keywords: coal, coal combustion by products, synthesis, geopolymers, zeolitic compound

Sep 1, 2012

By Pan, Jian, Siwei Li, Deqing Zhu

"It is great significance to realize the efficiently and comprehensively utilization of iron, manganese and aluminum from refractory high-aluminum and high-manganese iron ores. Aimed at the two types of low grade refractory iron ores, mineralogical characteristics were studied. The direct reduction behaviors and evolution of mineral compositions of single iron ores and their blended ones were analyzed, and the corresponding reduction mechanisms were demonstrated. The results showed that only a part of iron oxides in high-aluminum ore are transformed to metallic iron after reduction, while the other react with aluminum and silica to form fayalite and hercynite which are difficult to be reduced. For the high manganese iron ore, most iron oxides can be reduced to metallic iron and manganese oxides can combined with aluminum-silica minerals to form galaxite and tephroite, promoting the reduction of iron oxides. Co-reduction results demonstrate that reduction of high- aluminum ore can be promoted by adding with high-manganese ore. Metallization and metallic iron grains increase dramatically by elevate high-manganese blending ratio. At the ratio of 60% high- manganese iron ore in the pellet feed, iron-slag separate well with a slag assaying 28.51%~36.35% Al2O3 and the recovery of iron and manganese can be reached 93%, respectively. The high-aluminum rich manganese residue was recycled with H2SO4. INTRODUCTION The growth of the Chinese iron and steel industry has been pushed forward by its rapid economic development in recent years, and 1126 million tons of iron ore have been consumed in 2014, where 933 million tons were imported according to the data from World Steel Association [1]. However, iron resources are limited, and especially the reserves of high-grade iron ores are declining, so it is of significant importance to optimize the mining rate of iron resources [2] and to utilize low- grade refractory iron resources, such as high-aluminum iron ore."

Jan 1, 2018

By Ghislain Bournival, Cagri Emer, Seher Ata

"It is well known among flotation practitioners that the contact angle can be correlated with the amount of material recovered from feed by flotation. The contact angle of solids can easily be modified by the addition of a collector. However, some collectors also have frothing properties thus altering the solid and bubble surface properties simultaneously. To avoid this problem, a technique has previously been used in which silanol groups are attached to the surfaces of the particles, but this method has its own problems. In this work, silica particles with various surface hydrophobicities were prepared using an esterification process. By using alcohols with different hydrocarbon chain lengths, from 4 to 12 carbon atoms, surfaces with a wide range of contact angles could be prepared. The technique was used in the modification of silica particles that were tested in a fluidized bed flotation column, and a laboratory mechanical flotation cell. In parallel experiments, dodecylamine (DDA) was used as a collector. It was found that irrespective of the type of flotation machine and surface preparation method, there was a close correspondence between flotation recovery and the contact angle of the particles. The silanation process has known drawbacks relating to the presence of moisture during the reaction, and the stability of the silane coating after it is been prepared. Esterification does not suffer from these disadvantages. This work has shown that the esterification technique is a robust alternative method for preparing hydrophobic quartz surfaces."

Jan 1, 2014

By I. Kairyakov

The present paper is about the restoration of the molybdenum production in the floatation plant of Ellatzite-Med AD in Bulgaria. The process, based on a working design, includes the construction of a new floatation molybdenum section in the existing molybdenum department of the Floatation Plant using the so called Vemco inert-gas floatation machines, made especially for the molybdenum floatation. While in the ordinary floatation machines, block impellers create suspension of the air, sucked from the atmosphere with the slime particles of the concentrate, which creates conditions for oxidizing the reagent, Vemco inert-gas floatation machines are covered with hermetic lids and the air inside the chamber is used. The technology, suggested by Geotechkoper Ltd. for making the working project, employs special machines from Dor Olliver Aimco, suitable specifically for molybdenum floatation in order to reduce the oxidizing of the reagent sodium hydrosulphate. Also the transport of the chamber product is done in hermetic conditions as the molybdenum flotation is done in two floatation rows and refining operations 3 to 8 are placed in the second row. Thus in the basic molybdenum floatation together with the first and second refining operations, which are hermetically closed, an ambient condition with low content of oxygen is created, that is about 8% for oxygen and about 92% of nitrogen, in which the oxidizing process is extremely reduced. This in turn results in reducing the consumption of the reagent depressor ? sodium hydrosulphate. In that way there is an improvement of the economical indices of the molybdenum production.

Jan 1, 2014

By G. N. Jadhav

In India, bauxite deposits are concentrated in Central India, Western Ghats and Eastern Ghats. Bauxites from various regions in Gujarat were identified during the present investigations of geochemical mapping. Different types of Bauxites samples were collected from Kachchh, Jamnagar, Porbunder, Junagarh, Bhavnagar and Amreli areas of Gujarat state and were studied in detail for their geochemical signatures to plot the data on Geochemical map. Raw bauxites were characterized by using powder XRD, XRF, ICP and optical microscopy techniques (with the help of Model microscope having both transmitted and reflected light setups) and were later examined to grade their quality. Most of the bauxites from Kachchh region were of high-grade (gibbsitic) type; while those of Sourashtra region were of low-grade (lateritic / calcitic) types. Most of these bauxites were either of ferruginous/lateritic or of calcareous/calcitic types. Based on the mineralogical composition, such as gibbsite, hematite and/or goethite, Kaolinite and calcite minerals present in particular bauxites, the deposits were graded. Finally, the Geochemical mapping of Bauxites for Gujarat region was prepared and discussed.

Sep 1, 2012

By Y. F. Guo

Among the different valences of vanadium, V (?) is insoluble in acid, V (?) and V (?) is in-soluble in water but soluble in acid. Vanadium mainly exists as V (?) in vanadium titanium-rich material obtained by reduction -milling-separation from vanadiferous titanomagnetite. Therefore, the vanadium titanium-rich material can not be used to extract vanadium by acid directly. In this paper, the vanadium leaching was studied by oxidation roasting and acid leaching. Through oxidation roasting, vanadium is transformed from the insoluble V (?) into V (?) or V (?) in order to improve the leaching of vanadium. The results show that vanadium leaching increases significantly by oxidation roasting-acid leaching. Leaching of vanadium is up to 70.18% under the optimized conditions of roasting temperature of 950 ?, roasting time of 40 min, sulfuric acid concentration of 40%, leaching time of 4h, leaching temperature of 95 ? and liquid to solid ratio of 4 : 1.

Jan 1, 2014

By V. A. Luganov

Methods of treatment of pyrite concentrates differ, depending on the content of pyrite and non-ferrous metals: oxidation roasting, sulphatization roasting, smelting, direct hydrometallurgical treatment and so on. Existing technologies do not provide for high recovery of metals, expenses associated with existing technologies are high, and environmental issues, associated with the existing technologies need serious attention. We have developed universal technology of the activating-dissociating autogenous roasting of pyrite concentrates using air based, or air, enriched with oxygen, blow. The basic process is taking place in accordance with the following reaction: (1-x)FeS2 + (1-2x)O2 = Fe1-xS + (1-2x)SO2 +Q The products of this reaction are pyrrhotinized cinder and roasting gases, rich in SO2 (up to 18 % in case of air blow) and poor in SO3, that contain up to 1 % of elemental sulphur. Cinder contains different forms of pyrrhotite. These forms of pyrrhotite differ by its content (from Fe0.843S to Fe0.945S), thermodynamic, magnetic (from 4.10-1 to 3.6 SI units), flotation properties (with pyrite dissociation the ?-potential of the product is moving towards more electrically positive charge, from 0.95 for pyrite to 0.2 for dissociation products) and other properties that depend on the conditions of roasting. The combination of pyrrhotizing roasting with different methods of cinder treatment allows to increase the level of sulphatization of non-ferrous metals during the roasting; reduce the amount of blow used during the processing; reduce dust losses to the gas phase; reduce the capacity of gas cleaning system and increase resistance to corrosion of the gas-treatment system, used for the production of sulfuric acid from pyrites. This combination of treatments also allows to use magnetic separation and flotation for separation of ferrous and non-ferrous metal compounds during cinder treatment; perform de-arsenation of arsenic containing concentrates and by-products. Pyrrhotinized cinder may be treated by oxidizing and non-oxidizing hydrometallurgical methods. Keywords: Pyrite, polymetallic ores, sulphidization roasting, pyrrhotite, magnetic separation, arsenic sulphide

Sep 1, 2012

By J. X. Zhang, F. S. Niu

"In order to accurately detect whether the collision occurs between particle and bubble in flotation process, a collision detection method of particle and bubble, which based on morphological image processing and Otsu method, is presented. First of all, it utilizes image pre-processing to optimize images, the target area and the background area are segmented by Otsu method. Then, particle and bubble are fitted to a circle combined with the least-square method. It’s convenient to obtain the coordinate information and radius. Finally, the position of all particles is extracted to an image, which achieves the particle tracking and avoids the complexity of the continuous frame image tracking.Experimental analysis shows that the relationship between the two ordinate difference d and the bubble radius r has a certain influence on the collision detection when the dripping particles are close to the bubble, when d>r, the detection accuracy is 92%;When d=1/2r, the detection accuracy is 97%;When d=0, the detection accuracy is 100%. The result indicates that this algorithm can detect the collision between particle and bubble quickly, and the working hours of manual test are saved effectively ,the best position of dripping particles close to the bubble which is taken with a CCD camera should be in the range of the particle and bubble’s ordinate difference less than half of the bubble radius.INTRODUCTIONFlotation is an important technical means to separate useful minerals from ores. The flotation process of ores and materials in the world is treated by flotation technology up to billions of tons every year, so the study of flotation process is particularly important. Raising the collision probability between mineral particles and bubbles in flotation process is one of the key factors to improve flotation separation efficiency[1]. The study indicates that[2-4] the collision probability between particles and bubbles is influenced by many factors, such as particle density, particle size bubble size, etc. The analysis of these influential factors requires a lot of experiments. Therefore, it is of great significance to design an accurate collision detection method for the research of this field."

Jan 1, 2018

By V. Hudecek

Problems of sudden outbursts of rock and gas present in deep mine mining ones of the most complicated interrogation. It is searching for the methods of prediction and prognosis that can be most useful for the government of these phenomena. Till now the pressure and the desorption of gas in bore holes was consider to be the decisive criteria. By the work of authors with using of statistical date was verify that for considerable reliability of forecast and prevent outbursts is necessity investigate characteristics of workplace and other indicators. These indicators were analyzing and assemblage into mathematical dependences which represent active and passive force asserting with in the process of rush. It was validated by using the equations which are presented in the manuscript that the accuracy of pre-diction of the phenomena is higher and methods of preventions are better also.

Jan 1, 2014

By Z. Y. Ma, M. D. Liu, Z. Z. Liu, J. K. Zhou

"An optimization method of microwave assisted leaching of copper anode slime was proposed based on Taguchi method. The results showed that the solid-liquid ratio was the most important factor affecting SNR(signal noise ratio) of the copper, tellurium and selenium leaching efficiencies, and its contributions to the copper, tellurium and selenium leaching efficiencies were 58.34%, 55.54% and 60.74%, respectively. Solid-liquid ratio was a significant factor to SNR(copper, tellurium and selenium). Reaction period was a less significant factor to SNR(copper and tellurium) and concentration of sulphuric acid was a less significant factor to SNR(selenium) while microwave power was an non-significant factor, its contributions to the copper, tellurium and selenium efficiencies were 3.22%, 11.73% and 12.73%, respectively. The optimized parameters of the microwave assisted leaching of copper were as follow: microwave power of 500 W, reaction period of 10 min, solid-liquid ratio of 0.10 g·mL-1 and H2SO4 concentration of 1.0 mol·L-1. The optimized parameters of the microwave assisted leaching of tellurium and selenium were as follow: microwave power of 800 W, reaction period of 15 min, solid-liquid ratio of 0.10 g·mL-1 and H2SO4 concentration of 1.0 mol·L-1. The validation experiments under the optimized conditions has been carried out, the copper, tellurium and selenium leaching efficiencies were 98.66%, 84.32% and 64.54%, respectively. INTRODUCTION As important valuable by-products, copper anode slimes are collected from the bottom of the electrolytic bath in the electrolytic copper refining process(Kilic, 2013). The value of the anode slime is determined by the content of rare metals and precious metals(Liu, 2014). Generally, pretreatment of copper anode slime is the first stage of the whole process. The aim of the pretreatment process is to remove Cu, Te and Se etc and enrich the valuable metals. The methods of pretreatment process can be differentiated into: pyrometallurgical processing and hydrometallurgical processing(Amer, 2003). The hydrometallurgical processes are more promising compared to pyrometallurgical processes in terms of cost effectiveness, low energy consumption and environmental concerns(Ranjbar, 2014). However, the disadvantages of the hydrometallurgy process are evident, such as lengthy processing times and low efficiency. Therefore, it is necessary to develop a highly efficient and environmentally friendly pretreatment method."

Jan 1, 2018

By Marzio Piller, Girolamo Belardi, Jure Mencinger, Paolo Bozano, Gianni Schena

"The hydrodynamics of the Tri-Flo™, a two stage cylindrical cyclone used in dense media separation, is studied using Computational Fluid Dynamics. The flow field is simulated with an Euler-Euler Volume of Fluid two-phase approach and the Reynolds stress turbulence model.A unique feature of the device is that the separation medium suspension is pumped and introduced tangentially into the two cylindrical compartments while the raw feed is conveyed to the feed hopper and fed at the axial inlet. This feature allows to use less pumping energy and limits the unavoidable production of fines. The Tri-Flo™ complex flow pattern is little known but central to the efficiency of the separation.The velocity field is computed within the two compartments of the separator. The interface of the air-core that forms in the inner axial part of the cylindrical sections is identified and visualized. The numerical results for a reduced-size 100 mm ID Tri-Flo™ are compared against laser Doppler measurements on a transparent acrylic model (Chinè, 1995) operated with water. The robustness of the model and its prediction capability are verified.The possibility to accurately predict the velocity profiles within the vessel and their dependence on the main Tri-Flo™ operating and geometrical variables paves the way to a better understanding of the functioning of the separator, its design improvements and scale-up."

Jan 1, 2014

By I. Nishkov, I. Grigorova, M. Ranchev, S. Dzhamyarov

"Chelopech concentrator (part of Dundee Precious Metals) is located in central-western Bulgaria. The current process plant utilizes conventional primary crushing and SAG mill grinding, copper and pyrite rougher and cleaner flotation stages to produce a marketable gold-rich copper and pyrite concentrates. As in the most processing plants, the pyrite depression is carried out alkaline media using lime. The subsequent activation of pyrite mineral is achieved by adding sulfuric acid, which has an adverse effect on the flotation equipment. Therefore, a series of laboratory flotation experiment for activation of lime depressed pyrite by ammonium salts, such as ammonium chloride (NH4Cl), ammonium sulfate (NH4)2SO4 and ammonium bicarbonate (NH4HCO3), have been conducted. The obtained results showed that ammonium bicarbonate proved to be the most appropriate reagent choice for pyrite mineral activation. These results are confirmed by X-ray photoelectron spectroscopy (XPS), performed to determine the surface chemistry of pyrite in its natural state, after lime treatment and subsequent treatment by NH4HCO3. The registered XPS spectra indicate that the hydrophilic phases on the pyrite surface could be efficiently removed by using the ammonium salt NH4HCO3. The industrial use of NH4HCO3 as an activator of lime-depressed pyrite is a possible alternative for sulfuric acid replacement as a most widely used pyrite activator. Flotation experiments with addition of 200, 400, 600 and 800 g/t from each of the studied ammonium salts have been conducted. Furthermore, the impact of the flotation pulp pH within the scope of 9.00 – 10.50 was also investigated. The obtained results from the laboratory flotation experiments, showed that the pyrite activation with ammonium bicarbonate is an excellent possibility for replacing the sulfuric acid as main pyrite activator reagent, in order to eliminate the gypsum accumulation during the flotation of pyrite in Chelopech concentrator.INTRODUCTION The Chelopech deposit, located about 60 km east of Sofia is one of the largest Cu-Au deposits in Europe. The ore have complicated mineralogical and chemical composition. The main ore minerals are represented by pyrite, enargite (luzonite), tennantite, chalcopyrite and bornite. The average copper content of the mined ore is about 1.1 % and the gold content is about 4.0 g/t."

Jan 1, 2018