Search Documents

By S. Cagirici, Z. Öztürk, A. Hassanzadeh

Many flotation kinetics models have been studied in the literature. Their applicability was extensively investigated and argued in detail. However, model selection criteria were not adequately discussed from the statistical points of view. In this investigation, the kinetic behavior of a complex copper sulfide ore was studied in a mechanical Denver flotation cell focusing on flotation kinetics of chalcopyrite, pyrite and molybdenite. Different flotation kinetics models including nine common empirical models and four mathematical models namely Hill, Chapman (Sigmodial function), single rectangular (Hyperbola equation) and exponential were applied to the experimental data. In addition to assessment of the goodness of fit criterion for each model, a factor of model complexity was considered using information criteria (IC) (i.e. Bayesian information (BIC), low of iterated logarithm (LILC) and Akaike information (AIC) indices). The obtained results showed that the IC indices could simply manifest the best-fitted model to the experimental data. Whereas, the coefficient of determination values (R2) were relatively same for all models. By taking the R2 and model complexity criteria into account, the exponential model was chosen as the best representative mathematical model to demonstrate chalcopyrite kinetic behavior. However, Chapman model was selected as the best one for the flotation of pyrite and molybdenite. In case of the common first-order flotation kinetics models, fast and slow flotation kinetic model (Kelsall) was reasonably fitted the best to the given data of chalcopyrite. However, the gas/solid kinetics adsorption model was chosen as the best-fitted one for pyrite and molybdenite. Furthermore, it was found that mathematical models represent better results in association with flotation kinetic behavior of chalcopyrite, pyrite and molybdenite due to the consideration of more parameters in modeling. Finally, it was concluded that the IC indices must be applied to the process of model selection due to consideration of goodness of fit, complexity of a model and model consistency.

Jan 1, 2018

By Anuj Narang

Large-scale separation or flotation cells, used in the primary extraction in the oil sands industry, are integral parts of the overall process of bitumen extraction. Good regulation of the interface level between the bitumen froth and the middlings in these cells can result in a significant improvement in bitumen recovery and throughput, and heavily influence process economics. Automatic control of such industrial processes presents challenges such as multi-phase flow dynamics, variable process gain and time delays, poor quality of measurements and significant disturbances. This paper details a case study application of development of multiple models of the dynamics of the interface level and the design of model predictive controllers (MPC) for a separation cell process. A Model predictive controller (MPC) using linear models is designed and implemented in real time on an industrial separation cell. The industrial implementation results show that the MPC scheme provides significant benefits over the current operations which use a PID controller. The benefits include significant reduction in the variance of the interface level resulting in higher bitumen recovery and smoother downstream operation plus energy savings due to reduced underflow pump speed.

Sep 1, 2012

By Shailin Lalloo, Allan B. Nesbitt

A fluidised bed was exposed to high gravities by placing it in a centrifuge. The bed expansions were measured and compared with the bed expansions predicted by the Richardson-Zaki model (1954). The Richardson-Zaki model was found to predict effectively the fluidisation behaviour of defined particles in this increased gravity environment.

Jan 1, 2003

By T. Onnela

Metso Mining and Construction Technology is one of the world leading suppliers of equipment and knowhow for aggregate and mining industry. The processing capacity, ease of use, and reliability are featuring Metso?s state-of-the-art cone crushers. Crushing is a complicated process affected by numerous parameters. The optimized crusher kinematics is one of the key factors for high performance. To fine tune the crusher kinematics and crushing chambers one needs to know how different parameters affect. The main cone crusher parameters are head angle and diameter, gyration point, shaft speed, eccentricity, stroke length, and inclination and design of crushing cavity. Selecting the correct combination of these parameters is a multi task optimization challenge. In practical life there are more factors to achieve satisfactory performance, like crushing chamber wear and profile management keeping the performance constant over the whole wear life, control of crusher frame loads, ability to handle disturbances in feed material etc. The extensive research work has lead to a solution that enables the highest possible material density in the crushing chamber. This design provides maximum reduction of processed material and thus increased share of 0/10 mm product. High density in the cavity offers further benefits, such as high throughput capacity, less material contact with wear parts and even load on crusher frame and bearings. The challenge that an equipment supplier involved with high density crushing is how to design a robust cone crusher, which is able to cope with the high crushing forces due to high resistance from the crushed material against the gyration movement. Metso has launched a new series of cone crushers HP3, HP4 and HP5 that are all able to work in high density crushing applications The test results and evidence from over 300 installations clearly prove the effectiveness and importance of high density crushing. Keywords: cone crusher, crushing chamber, crusher kinematics

Sep 1, 2012

By V. V. Lodeischikov

This paper covers some problems of treatment of complex gold ores and concentrates containing copper, lead, zinc, antimony and uranium. All these metals may present in ores both as major and associated components. The paper suggests recommendations for early determination of relative value of the metals in ores, which largely contribute to the selection of concentration and metallurgical flow sheets. The focus of this work is on treatment of complex ores in gold plants. The metal extraction technologies used by such gold plants are typically aimed at maximum gold recovery. Therefore, production of base metals as by-products requires significant updating of the existing process flow sheets based on economic, environmental and other considerations. At the same time, cooperation between gold plants and base-metal plants is of great importance. This paper provides an overview of worldwide existing and innovative processes of base metals extraction from complex and refractory gold ores.

Jan 1, 2014

By E. V. Konoplev

Russia is one of the largest manufacturers of potash fertilizers in the world. Processing of potash ores basically is carried out by a flotation way. Potash ores of the Verhnekamsky potash deposit contain sylvite (KCl), halite (NaCl) and water insoluble impurity (up to 8 %), presented silicate- carbonate minerals, easily slimed by ore crushing in rod mills. Ore of some deposit sites, developed by ?Uralkali? Co, contains a significant amount of a carnal-lite (KCl.MgCl2.6H2O). Work practice of flotation potash plants has shown, that increase of car-nallite content in ore leads to increase magnesium ion content in a circulated plant brine (saturated salt solution of potassium and sodium chlorides-sylvite brine) and to deterioration of indicators of ore processing. In the Paper we present results of researches of floatability of various size sylvite and influences silicate-carbonate slimes on sylvite flotation in brines with the various magnesium chloride content. It is established, that with increase magnesium chloride content in the brine mainly decreases the flotation of coarse sylvite and amplifies adverse effect of silicate-carbonate slimes on sylvite flotation. In this connection deterioration of potash ore flotation is caused not only decrease sylvite floatability but also strengthening adverse action of water insoluble impurity on potash flotation. It is shown that the application of frothing agents, which render the stronger dispersive action on the colloidal-micellar structures of amine in the salt solution increases the absorption of collector on the sylvite and improves the flotation of sylvite into magnesium the containing salt solutions. The application of an organic depressor to the greatest degree of decreasing the absorption amine on the slimes and to the smallest degree possessing anionic properties proves to be most effective with the flotation carnallite of the containing potassium ores. It is offered the application the frother on a basis of glycol ethers and organic depressor on a basis of urea-formaldehyde resin. Results of industrial tests developed reagent modes for flotation treatment of ores with the raised carnallite content (to 6 %) on ?Uralkali? Co plant have shown that their application has allowed to receive equivalent indicators potash flotations at change of magnesium chloride content in the brine from 0.7 % up to 2.4 % .

Jan 1, 2014

By M. N. Chandraprabha

Arsenopyrite is often associated with sulphides like pyrite, chalcopyrite and galena in refrac-tory gold ores. Selective flotation of arsenopyrite from associated sulphides is desirable for effective gold extraction when the gold is preferentially associated with the arsenopyrite matrix. By contrast, presence of arsenopyrite in flotation tailings poses a serious environmental threat due to arsenic dissolution. To prevent arsenic contamination from the mine wastes, it would be more economical and environmentally beneficial to remove this mineral during the froth flotation step. Use of Acidithiobacillus thiooxidans in the detoxification of arsenic containing sulphides is outlined in this pa-per. Biomodulation using Acidithiobacillus thiooxidans resulted in the preferential depression of pyrite from arsenopyrite. By suitable conditioning with cells and collector effective separation of arsenopyrite from pyrite was achieved. Biomodulation with wild cells did not yield separation of arsenopyrite from chalcopyrite. However, bacterial affinity could be induced to a desired sulfide mineral through environmentally controlled adaptation techniques. Through the use of arsenic-adapted bacterial cells, selective removal of arsenopyrite from chalcopyrite was readily achieved.

Jan 1, 2014

Low-grade ore bodies, increase in rock competency, finely disseminated valuable minerals in the ore bodies, ore variability and water scarcity are among the technical challenges faced by the mining industry. These challenges have increased the business risk, capital investment and operating cost of the mining projects. Since the last 20 years, many large-scale concentrators have been built to cope with the above-mentioned challenges. Comminution, especially the fine grinding is an energy-intensive process. For example, the ball mill has a limitation in the fine grinding regime where the energy consumption increases exponentially when the product size is below 45 µm. The industry has been seeking for solutions that have a minimum risk and total cost of ownership. The stirred milling technology such as the TowerMill is well accepted by the industry as it has demonstrated the attributes required for fine grinding. TowerMill is a matured technology that has been adopted since the 80s for regrinding duty. Recently, this technology was installed in secondary and tertiary grinding duty to prepare a finer feed to rougher flotation. Four units of TowerMills were installed in a magnetite concentrator in Western Australia in tertiary grinding duty. Recently, Nippon Eirich has conducted process performance evaluation on the TowerMill circuit. The outcome of the exercise had indicated that the circuit is consuming 3.4 kWh/t to reduce from 55 µm to 35 µm with a narrow product size distribution. The effect of operating variables such as the specific energy, grinding media size, mill content % solids and mill feed configuration on the grinding efficiency were evaluated at the plant scale. Furthermore, the scale-up methodology was validated. The scope of this paper includes the performances of TowerMill and the validation of scale-up methodology.

Jan 1, 2018

By A. Akcil, O. Celep, C. Erust, E. Y. Yazici1, H. Deveci1

"Recycling of WEEE has already gain prime importance from both environmental and economic point of view. For the recovery of metals from e-waste, many conventional physical, bio/hydrometallurgical and pyrometallurgical processes are proposed. Economic potential of e-waste is mainly driven by its precious metal content. Physical separation methods (e.g. electrostatic, magnetic, eddy current and gravity separation) exploit the differences in the physical properties of metals and non-metals. Physical separation methods are simple and economically sound but they suffer from metal losses and ineffectiveness at fine sizes. Hydrometallurgical processes are promising owing to their relatively low cost, reduced environmental impact, potential for high metal recoveries and suitability for small scale applications. Hydrometallurgical processes can be developed for selective extraction of base/precious metals using suitable reagent systems. Sulphate-based leaching with a suitable oxidant (e.g. H2O2, O2, Fe3+) is effective for copper and other base metals. After removal/recovery of base metals, precious metals can be easily extracted using various lixiviants including thiosulphate, thiourea, cyanide and chloride. However, further research is required to develop new, cost effective and environmentally friendly processes and/or refine existing ones for leaching and, in particular, downstream processes. INTRODUCTION Electrical and electronic equipments are indispensable to modern societies with numerous applications in the field of medicine, transport, communication, education, security and environmental protection. With technological developments and innovations, the replacement of old equipment leads to ever fast accumulation of waste materials such as waste electrical and electronic equipment (WEEE or e-waste). People are upgrading their mobile phones, computers, televisions, audio equipment and printers more frequently than ever before (Babu et al., 2007; Lee et al., 2007). With the rapid growth in technology today, the life span and utilisation period of most electronic and electrical equipment has been reduced considerably with concomitant generation of huge amounts of WEEE over the past several decades. According to statistics presented by Balde et al. (2015), total WEEE produced around the world was 41.8 million tonnes in 2014 and expected to rise to approximately 50 million tonnes by 2018. Kumar et al. (2017) estimated that annual growth rate for the WEEE stream is 3–5% (Singh et al., 2016). The aim of this paper is to provide an overview of physical separation and hydrometallurgical methods available for the treatment of WEEE."

Jan 1, 2018

By M. Surracco, M. C. Tilocca

"Mineral comminution is often a costly process which also requires high level of energy. In the course of the studies carried out by the researchers of the Department of Civil-Environmental Engineering and Architecture at the University of Cagliari, aiming at the optimization of the reduction processes, it has been experimented, among of others, the effects of high-speed water jets on minerals grinding. As far as coal is concerned, some of the solutions initially adopted are presented in this paper, which essentially relied on the water jet power only, with secondary use of mechanical actions, to reach the most modern solutions that envisage the use of mechanical energy, normally used in traditional grinding machines, in synergy with hydraulic energy transferred by water jet.INTRODUCTION Mineral comminution can be rather expensive and demand a high-energy consumption, especially for fine sizes (Austin, 1979). Further interesting perspectives in this area may be offered by comminution means aided by high pressure water jets (Ciccu 2007), whose crushing potential is currently used for several operations such as cutting different materials, rock digging and industrial cleaning. The crushing action of water jets may induce a traction stress in materials where substances of a mineral nature, especially if characterised by permeable porosity, oppose a minor resistance (Griffith, 1920). The first solutions to this purpose essentially relied on the sole energy of water jets, with a secondary use of mechanical actions (Ciccu, 1993). Results were encouraging, despite the high values of specific energy for the low capacity of treatment. However, due to the difficulty in making the techniques mainly based on hydraulic energy practically applicable to solids comminution a solution was experimented, with some interesting results, consisting in the combination of mechanical energy, normally used in traditional grinding devices, with hydraulic energy transferred through water jets, in a synergic relationship (Ciccu, 1998; Tilocca, 2016)."

Jan 1, 2018

By L. G. Wang

The stability of foams and froth plays an important role in flotation, in which small amounts of relatively weak non-ionic surfactants (frothers) are used to produce air bubbles and foams. In the present work, factors affecting the stability of the foams produced in the presence of common frothers, such as n-pentanol, n-octanol, methyl isobutyl carbinol (MIBC), and polypropylene glycol (PPG), have been studied. We used the thin film pressure balance (TFPB) technique of Schelud-ko-Exerowa type to measure the equilibrium film thicknesses. The results were used to determine the contributions from the various surface forces to the disjoining pressures in the thin lamellae (foam) films formed between air bubbles. In addition, we used a model developed by Wang and Yoon (Colloids and Surfaces A: Physicochem. Eng. Aspects, 2006) to calculate the elasticities of the lamellae films at the critical thicknesses at which films rupture. The surface forces and elasticity da-ta were then compared with the foam stabilities in the presence of the various flotation frothers. It was found that foam stabilities are controlled by both film elasticity and surface forces, the relative contributions of which change with frother type and concentration. In general, surface forces play a more important role at relatively low frother concentrations, while elasticity plays a more important role at higher concentrations. At the frother additions usually employed in the mining industry, MIBC relies on surface forces while PPG-400 relies on film elasticity in producing stable foams. The former is capable of dampening the hydrophobic force, which is a major attractive force destabilizing lamellae films, while the latter is capable of reducing surface tensions at low concentrations.

Jan 1, 2014

"The most common agglomeration technique in iron and steelmaking is sintering, which requires the use of iron ore/concentrate mixtures, limestone and dolomite as fluxes and coke as fuel in order to produce the required melt at high temperature to cause agglomeration of the particles. Sinter feed blends containing high proportions of magnetite concentrate are difficult to granulate and to produce granules of high permeability, and sufficiently robust quasi-particles for successful sintering operations. Since the granulation of iron ore sinter feed requires no use of a binder, the added fluxes play a vital role in holding the granule particles together until they sinter. The fluxes also help to improve the granule quality and control slag composition in the blast furnace. It is well-known that the particle size distribution of the fluxes affects the granulation effectiveness and green bed permeability which determine the productivity, physical and metallurgical properties of the granules and sinter. Hence it is necessary to understand the role of flux particle size on granule properties so as to improve the granulation of iron ore sinter feed blends containing high magnetite concentrate. In this study, laboratory granulation experiments have been carried out on iron ore sinter feed blends containing high proportions of magnetite concentrate at different addition levels of limestone and dolomite mean particle sizes, to understand the influence of limestone and dolomite particle sizes on granulation rate processes and granule properties.INTRODUCTION Increases in iron ore production to meet the global demand for iron and steel products has led to the depletion of high grade iron ores and thus the current utilisation of low grade iron ore fines and concentrates. However, sinter, pellets and the lump are the required feed types used in the blast furnace. The high basicity sinter is the main iron bearing feed accounting for 70-85% in the blast furnace due to its good metallurgical and mechanical properties that allow high productivity, efficient processes and low production cost (Adam et al., 2017)."

Jan 1, 2018

By P. M. Solozhenkin

On the territory Sakha (Yakutia) are located largest in Russian Federation reserves of antimony ores, Sarylakhsk and Sentochansk deposits, amaunt 10% of world stocks of antimony. A processing gold antimony ores Sarylakhsk deposit is carried out on gravitation-flotation circuit to receive gold gravitation concentrate and gold-antimony flotation concentrate with the contents of antimony over 60%. The gold-bearing concentrate is treated on place hydrometallurgicaly to a high-standard product, accepted by gold bank cash department. At the ore dressing plant reached the highest recovery in world in a concentrate of antimony 90%~91.6%, and gold 85.7%~86.0% as a result of scientific research works. Studied the mechanism of interaction cations of metals Pb2+, Cu2+, Cd2+, Hg2+, Ag+ with a surface antimonite presented on the basis of modern physical-chemical methods: nuclear quadrupol resonance, x-ray electron spectroscopy, electron spin resonance. The industrial tests of sodium dimethyldithiocarbate were carried out which confirmed high recovery of Sb and As. The leaching Sb2S3 by bacteria Desulfovibro desulfuricans and transformation antimonite in antimony trioxide by Tiobacillus Ferrooxidans improved following cyanidation . The extraction of antimony in a solution 96.0%~98.0% under optimal conditions. The common total extraction in the appropriate commodity products for gold reached 98%, for Sb 96.5%. At a combination of bioprocessing and cyanidation 85.5% of extraction Au was achieved. The new solvents for antimonite were found. Now by the Close Joint-Stock Co ?Sarylach-Antimony? industrial plant is constructed for processing Au-Sb concentrates to receive antimony trioxide and gold from various antimony deposits of Sakha (Yakutia).

Jan 1, 2014

By W. Q. Zhao

In order to raise the utilization rate of phosphate resource of Al-Jalamid Mine in Saudi Arabia, a flotation experiment for its phosphate rock was carried out by using WF-01collector that have been produced by Wengfu Phosphate Mine. The results showed that WF-01 collector had extensive adaptability for Al-Jalamid phosphate rock, and the grade of phosphate concentrate could be up to 33% P2O5 mixing the upper, middle and lower beds rock as well as its 80% more recovery.

Jan 1, 2014

New technology for on-line particle size analysis of mineral slurries has opened up new applications for particle size measurement. In some cases the particle size distribution of the final concentrate is an important quality issue. This paper discusses established on-line particle size analysis technologies and presents experiences on the use of a new technique employing laser diffraction in several minerals processing operations. The main innovations in the new instrument are a simple dilution system and multiple scattering correction algorithm, which allows wide solids content variations of diluted sample in the measurement cell. Representative sample for laser measurement is produced by a simple and reliable dilution system. The applications discussed are; Blaine number measurement of Fe concentrate before pelletizing, grinding of variable batches of ore and paste thickener control.

Jan 1, 2014

By Yessengaziyev Azamat, Almagul Ultarakova, Onayev Murat, Barkytova Botakoz

"The research is aimed at solving the processing of waste products of titanium-magnesium production. The aim of the research is to extract synthetic carnallite and industrial products enriched with niobium from waste products of titanium-magnesium production. Analysis of the current state of the titanium and magnesium production in the Republic of Kazakhstan shows the availability of significant amounts of chloride wastes containing valuable components. Magnesium and potassium with an average content of 50-60 % potassium chlorides, 25-30 % magnesium chlorides are lost in the wastes of the titanium and magnesium production. Ust-Kamenogorsk Titanium Magnesium Plant JSC (UKTMP) currently imports carnallite that is a KCl-MgCl2X6H2O binary salt at quite high prices. Chloride wastes of titanium production, sublimates of dust chambers of a titanium chlorinator, sludge of a magnesium electrolytic unit and sludge of a carnallite chlorinator has been chosen as the targets of our research. The analysis of niobium distribution within any solid waste of a titanium slag chlorination process in UKTMP JSC showed that the highest content of niobium is in the sublimates of dust chambers of a titanium chlorinator in the ranges from 0.26 to 1.0 %. Among the niobium extraction technologies considered, the known method of its extraction from the chloride waste is leaching with weak solutions of mineral acids or alkalis in order to convert the chloride salts into the solution to be used for synthetic carnallite extraction. Besides niobium, other impurity components are transferred to the cake and shall be separated from the base metals. The effective method for this is the chlorination process enabling niobium transfer into the sublimates in the form of chlorides and thus separating it from the majority of the impurities. The condensed niobium chlorides are hydrolyzed transferring it into sediments in the form of oxide. New ways of processing waste products of titanium-magnesium production with the receipt of marketable products are relevant in the development of processing of mineral raw materials."

Jan 1, 2018

By Richard A. Williams

The mineral processing community have been amongst the pioneer developers and early adopters of key platform technologies in analytical methods, chemistry, physical separation and advanced modelling. Fundamental research will continue to have a significant impact driven by the continued development of sustainable practices. Major drivers and challenges for change in our industry in the next two decades include: reduction in energy uses in processing; discovery of new energy materials; adoption of green chemistry routes; safeguarding of water resources; and demonstration of adherence to best practice at all times. With increasingly global mining enterprises, the provision of internationally accepted benchmarks for performance will continue to drive the creative process. This lecture highlights major opportunities around a new paradigm of Multi-scale Measurement coupled with Multi-scale Modelling, based on advanced sensors, communications and computing. Connecting real-time measurement sensors with dynamic simulation models opens up new horizons for visualising the process behaviour from an experimental and theoretical basis. Examples are given of the potential of this methodology and its implications for better design.

Jan 1, 2003

By Auhin Kumar Maparu

Metal oxide nano-particles are used as additives in various industrial applications such as pigments in paints, additives in adhesives, plastics, cosmetics, functional coatings, personal care and health care products, for antibacterial applications and more recently in heat transfer applications. In most of these applications, usually dry nano-particle powders are added to the formulations. However, often it becomes difficult to achieve a uniform and stable dispersion of nano-particles in the given formulation. Thus, a scalable and commercially viable process for in-situ production of stable nano-particles suspensions in the desired medium will certainly be more beneficial. Ultra-fine grinding in high energy mills (planetary mill, stirred media mill) has been used to produce fine particles (sub-micron size). However, in order to obtain nano-particles (particle size <100 nm), the choice of appropriate dispersant and solvent is crucial, since freshly generated nano-particles tend to agglomerate due to their high surface reactivity. We have employed molecular modeling (MM) based selection methodology to arrive at the most suitable solvent?dispersant combination for preparation of the given metal oxide nano-particles. Molecular modeling techniques are employed to compute the interaction energy of a given dispersant with surface of the metal oxide particles in the presence of the dispersion medium. The interaction energy helps identify a dispersant that has strong affinity for the metal oxide surfaces allowing for strong dispersant adsorption and hence a more stable dispersion. For example, in case of aqueous nano-titania suspensions, poly-carboxylic acids like citric acid provide better dispersion than mono-carboxylic acids like lauric acid, mysristic acid, and oleic acid. While in non-aqueous medium like ethanol, p-hydroxybenzoic acid and glycerol trioleate perform better. The suspension is produced in-situ by ultra-fine grinding of the metal oxide powder in the presence of the selected dispersant and dispersion medium in a planetary ball mill. By careful selection of various process parameters such as percent loading of powder, jar filling, grinding media to powder ratio, time and amount of dispersant addition, both aqueous and non-aqueous suspensions of metal oxide nano-particles with average particle size less than 100 nm are produced. The aqueous suspensions of alumina and titania produced in presence of citric acid dispersant exhibit median particle size of 83 and 62 nm, respectively. These suspensions have been found to be stable for nearly 3 years. The nano-particles thus produced are used in the preparation of nano-fluids?advance heat transfer liquids, which show enhanced heat transfer capabilities and unaltered stability and performance even after several heating-cooling cycles. The nano-particles are also utilized for making efficient photo catalysts, which are found to be highly effective under sunlight. Keywords: stability, nano-fluid, milling, grinding, thermal conductivity, nanocoolant, photocatalyst

Sep 1, 2012

By M. Q. Xu

During the flowsheet development for a potential commercial Cu/Ni separation plant at the In-co?s Sudbury operation, extensive laboratory and miniplant studies were carried out. There are two potential feed streams for Cu/Ni separation at the existing operation. It is shown that Cu/Ni separation from the rougher concentrate is relatively simple without need of regrind. However, Cu/Ni separation can be difficult from the bulk concentrate because of the presence of excess flotation reagents in the bulk concentrate slurry and locked particles. Excess flotation reagents created excess froth increasing entrainment. By replacing the slurry water with tap water and with addition of some hydrogen peroxide, entrainment is minimized and good Cu/Ni separation is achieved on the bulk concentrate. Fine regrind is required to increase liberation of the locked particles for ultimately high copper recovery at the minimal nickel content.

Jan 1, 2014

By V. A. Chanturiya

In Pt- and Au-keeping complex ores processing, about 10% ~ 15% of noble metals are lost with true tailings that are due to low floatability of Pt- and Au-keeping minerals by the conventional collectors. With the aim to achieve the effective recovery of noble metals at flotation of Pt-Cu-Ni and Au-keeping ores organic complex reagents keeping electron-donating atoms of nitrogen, oxygen, sulfur or phosphorus may be offered as selective collectors for the indicated minerals. These rea-gents tend to form complex compounds with PGM. Besides this, Cu-Ni-Pt and complex Pt and Au carbonated mica ores are characterized by finely disseminated (up to nanometer size) mineral forms of Pt in multivalent states. In this connection, the use of a combination of the strong ionic collectors with nonionic reactants that are capable to derivate complex compounds with multivalent PGM seems to be expedient for this type of ores. In the research new complex reactants were tested such as cyclic alkylene-trithiocarbonates, oxyalkyl butylxanthogen acid ethers, a combination of the collectors ? mercaptobenzothiazole (MBT) and dialkyldithiophosphates (DTP). Sorption and flotation tests were made with monomine-ralic samples of chalcopyrite, pentlandite, pyrrhotite, pyrite, and Pt-Cu-Ni sulfide ore samples. Sorption properties were examined by the extractive UV spectrophotometric method and potentiometric measurements. To indicate a structure of modified xanthate solutions the method of a thin-layer chromatography (TLC) was applied. The chromatographic behavior of the basic components of modified xanthate solution ? ButX, cyclic propylene-trithiocarbonate (PTTC), diethyl-dithiocarbamate (DEDC) and the product of its modification ? oxypropyl-S-ether of dithiocarbamatic acid was studied on plates ?Silufol UV ? 254?. The composition of organic solvents and its ratio in a mobile phase was deter-mined for simultaneous chromatography of the main components of a reaction mixture. It was found that operating selectivity of MBT, DTP and cyclic alkylene-trithiocarbonates incorporated in modified xanthate in relation to Pt-Cu-Ni and Au-containing sulfide minerals might be explained by an electoral sorption of this nonionic collector on a surface of the minerals studied. It was demonstrated that the application new reagent modes with the use of a combination of designed complex reactants helped to increase the extraction index of Pt- and Au-keeping minerals from complicated ores.

Jan 1, 2014