Search Documents

By Nóra Schreithofer, Kari Heiskanen

"INTRODUCTIONThe knowledge of the adhesion forces between particles and bubbles is of key importance in the improvement of flotation models. The development of the Colloidal Interaction Force Measurement Apparatus (CIFMA) opened the possibility to quantify the adhesion forces between particles and bubbles. The aim of this study was to examine the effect of three main variables: the approach velocity, the loading force and the loading time on the adhesion force between an air bubble and a hydrophobized silica particle."

Jan 1, 2003

By James A. Finch, Linda Restrepo, Mitra Mirnezami, Amy Buchanan, Maryam Hashemi

Settling rate studies on slurries from Cu/Zn flotation plants occasionally reveals two aggregation maxima at pH 8-10 and 10-12 (Figure 1). From measurements on sphalerite and silica suspensions the double maxima could be replicated. These maxima correspond to the effects of Zn and Mg ions. The aggregation mechanism of both ions is related to the formation of the corresponding hydroxide precipitate. A combination of chemical and electrostatic bridging by the hydroxides is considered to be the aggregation mechanism.

Jan 1, 2003

By Rod Hocking, Nenad Djordjevic, Randolph A. Pax

"Semi Autogenous (SAG) mills exhibit complex interactions between the competing processes occurring inside them. Traditional practice is to measure the operation of the SAG mill at an operating point in terms of its load, power draw, steel load, ore throughput rate, water addition rate and more recently the feed size distribution. However significant departures from standard operating conditions can occur due to changes, for example, in ore hardness, the quest for higher throughputs and mill internal geometry.Fundamental to SAG mill operation are the internal processes that ensure that a given ore throughput and discharge grind size are obtained and maintained. These processes can be measured using non-contact acoustic emissions from the SAG mills which utilise the information rich noise that is generated by the grinding, flow and charge movement inside a mill. Non-contact acoustic in-mill measurements can be used for the validation of discrete element modelling (DEM). The approach being reported in this paper is to model the individual physical processes and then to simulate the assemblage of a physical mill.By modelling the assemblage of steel balls in a 1 m pilot mill and duplicating the experimental arrangement exactly with the PFC3D model, it was possible to replicate the pattern of falling balls in the experimental mill. Furthermore, the key features of the acoustic emission spectrum that was calculated compared favourably to the measured spectrum at low frequencies. The experimental spectrum is shown in Figure 1."

Jan 1, 2003

By Olgac Kangal, Ali Guney, Gulay Bulut, Guven Onal, Ayhan A. Sirkeci

"This paper presents the results of pilot scale column flotation applications in the two different copper concentrators in Turkey. The Kure Copper Plant is located in the Black Sea Region of Turkey. There are four types of copper ore formations in the Küre region. The so called disseminated ore contains 60-70% siliceous minerals of which Cu content is around 0.5%. The remaining three ore types in the region are generally named “massive ores”. The massive ores may assay up to 15% Cu and the major gangue mineral is pyrite associated with relatively little amount of silica. The main copper mineral in all formations is chalcopyrite that is generally finely disseminated in pyrite therefore satisfactory liberation requires ultrafine grinding especially in the case of the massive ores.A blend of these ores, containing 1.7% Cu on average, is fed to the Küre Copper Concentrator whose capacity is 1.2 million tons of ore annually. Unfortunately, today the plant operates below its designed capacity treating around 550,000 tons of ore per year. The design of Küre Copper Plant was undertaken by the Outokumpu Company of Finland. The operation of the plant is almost automatically controlled and the feed, the concentrate and the tailings are assayed for copper by on-line XRF analysers. The particle size analysers are also connected to the grinding circuit. The feed material is ground almost below 50 µm and the flotation is conducted around pH 11.2 using Hostaflot X-231 (a trade mark of Hoechst) as the collector. Apart from the rougher cells, there are four cleaning stages after which the final concentrate is produced. A very fine grinding requirement for an adequate level of liberation makes successful flotation difficult and consequently the final concentrate can hardly assay above 16% Cu leading to copper losses around 20% in the tailings that contains 0.3% copper."

Jan 1, 2003

By Peter J. Coghill, Michael J. Millen, Brian D. Sowerby, Kirby D. Cunningham

"CSIRO Minerals has developed an integrated particle size analysis system for deployment in the grinding circuits of minerals processing plants. The system includes a slurry sampling station, a de-aeration tank and an ultrasonic particle size analyser (UltraPS). The UltraPS analyser is based on ultrasonic attenuation and velocity spectrometry combined with gamma-ray transmission. The technology is applicable to the measurement of 0.1 to 1000 µm diameter particles directly in highly concentrated slurries without dilution. The analyser incorporates a gamma-ray transmission gauge utilising an ultra-low activity radioisotope source that is exempt from International Atomic Energy Agency (IAEA) and Australian licensing regulations.The UltraPS analyser consists of a submersible probe and an electronics package. The probe can be immersed directly in a minerals processing plant stream if the aeration level in the stream is low. For applications where a de-aerated slurry stream is not available, CSIRO has developed an integrated system that includes a sampling station, a de-aeration tank as well as the UltraPS analyser itself. A schematic drawing of the continuous flow gravity fed system is shown in the figure. A commercial sampling system is used to supply slurry at a rate of 2.5m3/hr to the deaeration tank. The aim of the de-aeration tank is to remove air in the slurry to a level where meaningful particle size measurements can be performed. The tank volume is about 0.2m3, thus giving the slurry flowing through the tank a mean residence time in the tank of approximately five minutes. Tests at a number of concentrators have shown that five minutes is sufficient time for slurry to de-aerate to a level where ultrasonic measurements can be made. The tank incorporates an ultrasonic level detection sensor and flow to the deaeration tank is adjusted based on the level of slurry within the tank. The UltraPS probe is mounted through a flanged section of duct, which is bolted to the bottom of the de-aeration tank."

Jan 1, 2003

By A. V. Bogdanovich

Until recently, in consideration of fundamentals of gravity concentration theory, all computations have been based on determination of particles? fall velocity in an unrestricted medium (hydraulic size). Meanwhile, gravity separation processes are realized under conditions of particles? restricted fall, when important and sometimes decisive role is played by interacting forces of particles, dependent on their varying size, density and shape, i.e., segregation forces. We have developed devices and methods for measuring segregation velocities of fine particles of various size, density and shape during their loosening in air or aqueous medium. Besides, to exclude influence of medium upward flows, loosening was provided by superposition of vertical harmonic oscillations on measuring cell. It was established, that maximum segregation velocities are observed at certain optimal acceleration values and amplitudes of oscillations; excessive loosening leads to mixing and worsening of segregation. Velocity of some particles segregation through others depends on particles? size, density and shape, as well as nature of medium (air, water). Absolute segregation velocities of particles in air medium may reach 1~2 mm/s, in aqueous medium such velocities are by an order smaller. Analysis of rare-metal sands material gravity concentration results showed, that owing to segregation process during gravity separation, fine-size isometric particles of heavy minerals are recovered into gravity concentrates more actively, than larger ones, but more elongated in shape. It is convenient and simple to estimate mineral grains? shape by extent of their oblongness, described as ratio of particle minimal dimension to maximum. Besides, mineral mixtures gravity separation results are directly related to extent of oblongness of heavy particles, recovered in gravity separation process, and also to root-mean-square coefficient of their shape variation. The performed research showed that particles segregation in gravity concentration process plays not a lesser role, than hydrodynamics parameters, and demands further theoretical inquiry and experimental studies.

Jan 1, 2014

By P. K. N. Raghavan

Bauxite is the principal source for the production of aluminum metal which has gained tremendous importance over the years due to its versatility as a metal capable of substituting almost all of the non-ferrous metals, non metals like wood, plastics, fibre glass, etc. and even steel in many applications. 90% of the high purity alumina needed for the production of this wonder metal in the world comes from bauxite. Even though alternate methods have been developed to produce alumina from non bauxite sources, owing to the high capital and operating costs involved, Bayer process still retains the superiority among all the methods by virtue of its simplicity and favourable economics. Bauxite continues to be the perfect ore for alumina production and its remarkable utilization makes it the most important non-ferrous ore. Most of the Alumina Refineries in the world process different types of bauxite and that too from varied sources. The technology employed in the Alumina Refineries depends on the Bauxite processed, with an ultimate view to produce alumina of required quality in the most efficient manner. Bureau of Indian Standards (BIS) and Indian Bureau of Mines (IBM) had from time to time put forward bauxite specifications for metallurgical and other applications. However, these are found no fully based on alumina technology, present developments and availability of different types of bauxite in the country. The aim of this paper is to provide scheme of metallurgical grading of Indian Bauxite based on the background of alumina processing technologies and availability of various types of bauxite in the country. Efforts are made here to evaluate beneficiation techniques for central Indian Bauxite from the point of view of alumina production. Keywords: bauxite beneficiation, digestion, alumina, gibbsite, bohemite, diaspore

Sep 1, 2012

By D. Pienaar, B. McFadzean, T. Jordaan

"Dithiophosphate (DTP) collectors have the lowest affinity for sulfide mineral surfaces compared to other common sulfide mineral collectors, such as xanthates and dithiocarbamates. In some cases it has been found that DTP does not adsorb onto the mineral surface at all and yet increases in recoveries and grades are noticed with the addition of DTP. Many studies have investigated the interactive effects of collector mixtures. However, there have been relatively few studies on the interactive effects between frother molecules and collectors. This study investigates the interactions between different types of frothers and sodium diethyl dithiophosphate.The study found that there were large increases in pyrite and galena microflotation recoveries at both pH4 and pH9 when DTP was mixed with small amounts of frother at a constant bubble size, showing that these increases were neither mineral-specific nor pH-specific. The same effect was not present when xanthate was used as a collector. The increases in recovery when using the DTP-frother mixture were similar irrespective of the type of alcohol or polypropylene glycol frother that was used. In an attempt to distinguish the mechanism of enhanced flotation recovery, various supplementary experiments were performed. It was found through adsorption experiments that no DTP was adsorbing on to the mineral surface. Therefore, interactions at the air-water interface were performed. Surface tension and critical coalescence concentration tests showed that, while DTP is a weak surfactant at the air-water interface, it does not have a synergistic effect in the presence of frother. DTP-frother mixtures do, however, show interactions in the froth phase, indicating an interaction in the thin films. It is proposed that there is a DTP-frother interaction on the bubble surface that enhances the rate of film thinning at the 3-phase bubble-particle contact."

Jan 1, 2018

By Georgios N. Anastassakis

"The depletion of the high-grade chromite ores and the inefficiency of the gravimetric methods to process fine particles has shifted the industrial and research interest from gravimetric separation methods to flotation. However, the response of the minerals to various flotation schemes is not clearly established. In this work, the physicochemical behavior of chromite and olivine is studied using a fatty acid collector.The minerals used were from Vourino area (Kozani, Northern Greece). Macroscopically pure samples of chromite and olivine were selected by hand picking, crushed and subsequently ground to the required size. Each sample was then submitted to panning and magnetic separation for the removal of impurities. The mineralogical and chemical analysis of the purified samples revealed the following: a) The purity of chromite was 95% while the minor constituent was mainly magnetite. Its chemical analysis was: 12.50% Fetot, 2.50% SiO2, 54,54% Cr2O3, 9.31% Al2O3, 0.47% CaO, 13.10% MgO. These analyses show that Cr3+ has been substituted by Fe3+ and Al3+ as well as Fe2+ has been significantly substituted by Mg2+. b) Forsterite is the main constituent of olivine either as pure forsterite (Mg2SiO4), which is the prevailing form, or as iron-forsterite [(Mg,Fe)2SiO4] in less amount. Chrysotile, which belongs to the serpentine group, was also detected at a percentage of 10-15%. The chemical analysis of olivine was: 36.90% SiO2, 0,53% Cr2O3, 7,43% Fe2O3, 0.72% Al2O3, 0.91% CaO, 47.00% MgO, 6.02% LOI.The electrokinetic behavior of the minerals was studied in a electrophoretic mass transport equipment Model 1202 of Micromeritics. The reagents used were sodium hexa-metaphosphate of commercial grade and sodium oleate."

Jan 1, 2003

By K. Malysa

Bubble collisions with ore grains and a selective formation of the bubble-grain aggregates are necessary steps for flotation separation of useful and gangue components of an ore. For the attachment of valuable mineral grain to the colliding bubble a liquid film, separating the bubble and the grain needs to rupture during short time of their collision. High hydrophobicity of the grain surface is favorable because stability of the separating (wetting) film is much lower at such surfaces, that is, the film ruptures faster and at greater thickness. Simultaneously, it needs to be kept in mind and taken into consideration that high affinity to air is a typical feature of hydrophobic surfaces. Thus, when the hydrophobic surface is immersed into aqueous phase the air can stay attached to such surfaces and affect kinetics of the bubble attachment. The paper presents results and analysis of dynamic phenomena occurring upon the collision of the rising bubble followed by its attachment to hydrophobic (Teflon) plates of different roughness. The influence of the Teflon surface roughness, solution concentration, bubble size and impact velocity on bouncing of the colliding bubble, time of the three phase contact (TPC) formation and drainage time of the liquid film, formed between the solid and bubble surfaces, is described. High hydrophobicity, as showed earlier (Malysa et al, 2005), does not assure that each collision leads to the TPC formation and attachment of the colliding bubble. Roughness is the parameter of crucial importance for kinetics of the bubble attachment to hydrophobic surfaces (Krasowska and Malysa, 2007; Krasowska et al, 2009; Kosior et al, 2011). Enlarged roughness of the Teflon plate, from ca. 1 to 80µm, results in shortening the time of the TPC formation (bubble attachment) by over an order of magnitude - from 105 to a few milliseconds only. Higher surface roughness means that larger amount of air can be entrapped in bigger scratches and cavities of the Teflon plate during its immersion into aqueous phase. Results documenting importance of the air presence are showed and mechanism of the air facilitated TPC formation and bubble attachment to hydrophobic surfaces is described. Keywords: bubble collisions, hydrophobic surfaces, teflon plate roughness, TPC formation

Sep 1, 2012

By Ronald Díaz

"Cerro Corona is a porphyry ore with different geometallurgical units and alterations produced by an extensive family of geological failures that have determined a special type of mineralization. With the increasing depth of the mine, it is estimated that the host rock will be less altered. Consequently, the ore will have a higher resistance to breakage accompanied by associated problems such as lower throughput. In light of this reality, various projects have been carried out with the objective to optimize mineral processing of ore with low clay content and high hardness, including reducing the blasting grid, increasing the load factor, using adequate mixtures of hard ore, reducing crusher settings, installing air guns in the transfer chutes, increasing ball charge, and changes in the lifter design, wear control in the hydrocyclones, syntonization of control logics, supervisor control of the SAG mil, characterization of feed ore, etc. However the most important factor was the teamwork between mine and plant personnel, aiming at common objectives for the company. These projects started in 2011, including characterization of mineralogical domains, breakage and blasting characteristics, and also a revision of the actual operating conditions in the crushing and grinding circuit. The development of different designs of the SAG mill lifters and the unloading grates, a 16% ball charge increase, improvements in the blasting process, reduction of the primary crusher setting, weight reduction on the feed lid, and variation of operational parameters, all allowed the company to achieve its objectives of maintaining impact control and steel recharge within the expected operational parameters. The achieved throughput is above design capacity, sustainable, and not without new challenges for maintaining and optimizing this production level."

Jan 1, 2014

By Haghi. Hamed, Javad Vazifeh Mehrabani, Mehdi Sedigh

In this investigation, the possibility of physical separation methods such as attrition scrubbing, hydro-cycloning and also reverse flotation were investigated for silica and calcite removal from relatively low grade kaolin. The head sample was provided by the Iran China Clay Company and the major oxides contained in the head sample were Al2O3, SiO2, CaO and Fe2O3 with grades of 15.07%, 71.05%, 4.35% and 0.52% respectively. The liberation degree of calcite and iron impurities from kaolin particles were over 80% for particles finer than 210µm and 53µm respectively. Attrition scrubbing tests were carried out with scrubber cell of the conventional Denver flotation cell model D-12. Laboratory scale hydro cyclone was applied for the beneficiation of kaolin. Attrition scrubbing tests with control screen of 106µm did not achieve the desirable yield for purification of this kaolin sample, but hydro cyclone experiments resulted in better results. Hydro cyclone with 2.54 cm diameter used and the only variable was the cyclone inlet pressure ranging from 68.65kPa to 98.07kPa. The best inlet pressure was found to be 68.65kPa. Based on the optimized condition, Al2O3 and CaO amount in the hydro-cyclone overflow was 23% and 1.47% respectively. However weight recovery of the overflow in each cyclone experiment was less than 30% and multi stages of hydro-cyclones would have to be applied for higher weight recovery and better yield. All of the flotation tests were carried out in the conventional Denver flotation cell model D-12. Reverse floatation tests for calcite removal were carried out under alkali pH based on full factorial design of variables in 2 levels including one center point. The three parameters tested were collector dosage (gr/ton), pH and depressant dosage (gr/ton). The collected data from flotation tests were analyzed and optimized collector and depressant dosage were 1000 gr/ton and optimized pH was 8.5. Under the above mentioned conditions, calcite removal was about 75% and CaO content in the final product was reduced from 4.35% to 1.33%. However calcite removal will increase to more than 83% if the feed particle size in flotation tests is reduced from 210µm to finer than 53µm. Finally after optimization, the best working condition and possible flow sheet were developed.

Jan 1, 2014

By Lokesh K. Thakur, Peter Radziszewski

"For the cases tested (11 mills with 15 operating conditions), the Bond abrasion test steel media wear rate prediction gives an overall error of 73% and a standard deviation of 192.5%. However, total steel media wear in a given mill (ball or SAG) grinding process is a product of three recognised wear mechanisms -- impact, abrasion, and corrosion. A total media wear model can be defined on the assumption that the effect of each wear mechanism can be independently determined which allows for a total media wear model to be defined as the summation of the wear result of each mechanism (eqn. 1). It is assumed that impact and abrasive media wear is a function of the energy dissipated in impact and abrasion as estimated by a DEM charge motion simulation. Corrosive media wear is assumed to be a function of the media surface area present in a mill.The 3 initial tests developed (steel abrasion wheel, corrosion batch mill, impact chamber) coupled with the impact and abrasion energy spectra from a DEM charge motion simulation produced total steel wear rate results for the same cases as the Bond abrasion test giving an overall error of 0% and a standard deviation of 66.1%. However, if one were to consider the general observation that wear is proportional to energy and maintain the assumption that corrosion is proportional to media surface area then one would realize that the total media wear eqn. (1) can be reduced to eqn. (2). As this is a linear equation and one has, for the same mill, media wear and operating data for three different operating cases, one obtains three equations with three unknowns. This defines a simple matrix manipulation to determine the constants k1, k2 and k3. From the previous data set, we had 6 identical mills grinding the same ore but having different worn liner profiles and charge volume which provided the opportunity to average out the ki values over 20 combinations of 3 cases. With the determined ki values, it was possible to determine a second estimate of the contributions of impact, abrasion and corrosion to total media wear giving an overall error of 0% and a standard deviation of 56%."

Jan 1, 2003

By Sanggono Adisasmito

"The quality of the higher education in Indonesia is being improved by implementing a program financed by the World Bank under a project named QUE (Quality for Undergraduate Education). The investments are provided to selected study programs through a competitive selection process. The grant finances staff development, the purchase of equipments, textbooks, consumables, technical assistance, and incentives for outstanding faculties such as teaching grants, project grants, lecture note awards, and educational policy studies. These additional investments are provided to produce chemical engineering graduates that will compete beyond the national market.Chemical Engineering Department of Institut Teknologi Bandung in Indonesia has been selected to receive the QUE grant beginning the year 2000 and ending the year 2004. The department is actively involved in the mineral processing issues, particularly in the aspects of energy supply and the environmental protection. The activities are distributed in different laboratories and areas of expertise, such as: thermodynamics and utility systems, process equipment, chemical reaction and catalysis, microbiology and bioprocess engineering, process control, ceramics, as well as polymer and membrane technology. The main objectives of the QUE project are to improve the undergraduate program in the following aspects: Relevance, Academic atmosphere, Institutional management and commitment, Sustainability, as well as Efficiency and productivity, or abbreviated as RAISE. At the end of every fiscal year, the progress of the program is evaluated to measure the effectiveness of the project.The achievement of the QUE project objectives were assessed using performance indicators developed during the program design. There are six indicators to measure the performance of the individual program of study, such as: (1) Admission Test score, (2) average students' Grade Point Average (GPA), (3) average graduates' length of study, (4) graduates' waiting time before getting first job, (5) Test of English as Foreign Language (TOEFL) score, (6) Graduate Record Examination (GRE) score. Essentially, the RAISE evaluation criteria will be used to perform three main functions, such as (1) to measure the achievement through the six quantitative performance indicators, (2) to support the progress of evaluation and reporting throughout the implementation of the program, (3) to provide a universal framework for qualitative evaluation."

Jan 1, 2003

By W. H. Cheung

Nickel (Ni) plays a major role in the production of steel and other major alloys. There are two sources of Ni: laterite and sulphide ores. Global reserves of sulphide ores are being rapidly depleted, while there are enormous reserves of Ni laterite, much of it in Australia. As well as being present in huge amounts, Ni laterites have the advantage of containing cobalt (Co), a valuable mineral. Over the past decade, these factors have been driving the industry to explore the processing of Ni laterite. A route that has been used commercially in processing nickel laterite ore involves the thermal activation of the minerals by pre-reduction followed by ammoniacal leaching (Caron). Although this process has been effective in processing the goethite rich laterite minerals, the higher-grade serpentine-based minerals have been shown to be less susceptible to this process. This has been attributed to the formation of inert olivine phases. In this study, we examined the use of an alternative lixiviant, sulphuric acid, in leaching pre-reduced limonite and weathered saprolite nickel laterite ores. The specific aim of this study was to examine the sulphuric acid leaching of Ni and Co from pre-reduced laterite minerals, and to understand the role of mineral transformations in this metal dissolution. Synchrotron based X-ray diffraction was used to examine the transformation of goethite (FeOOH) to spinels and serpentine mineral ((Mg,Fe)3Si2O5(OH)4) to olivine. Reduction tests were carried out using CO and CO2 reducing gas mixtures and temperatures from 400 °C to 700 °C. The rate of formation and disappearance of specific Bragg peaks during reduction of specific minerals were used to derive an understanding of these solid-state reactions. Laboratory based reduction tests and leaching in sulphuric acid were used to validate the effect of these mineral transformations. The results suggest the versatility of sulphuric acid in leaching nickel from spinels and olivine, which was achieved at the expense of lower selectivity. Cobalt dissolution was found to be dependent on the nature of ferro-cobalt alloy formed during reduction.

Jan 1, 2014

By B. McFadzean, K. Moller

"The mechanism whereby thiol collectors adsorb onto a mineral surface has been widely studied. Most of these studies examine the mineral surface at equilibrium state and, often, well above monolayer coverage. However, the formation of species at the mineral surface is a complex process that is both kinetically and thermodynamically controlled. In a typical industrial application, the dosage of collector will be around monolayer level. This study uses isothermal titration microcalorimetry to measure the heat evolved during the reaction of sodium ethyl xanthate (SEX) and sodium isobutyl dithiocarbamate (SIBDTC) and their mixtures with galena and chalcopyrite. The sensitivity of the instrument allows heats of reaction of sub-monolayer quantities of thiol collector to be measured.The study found that both the magnitude and kinetics of the reaction between a collector and a mineral surface was dependent on the type of mineral and the type of collector. Proposals are made for the reactions based on literature and the evidence from this investigation. It was found that when collectors were reacted with mixtures of galena and chalcopyrite, that the magnitude of the reaction was lower compared to that measured for the pure minerals alone. This may be due to galvanic interactions between the minerals, resulting in a passivating effect on one or both of the minerals."

Jan 1, 2014

By Tsuyoshi Hirajima, Hideyuki Okamoto, Himawan .. T. B. M. Petrus, Keiko Sasaki

"Flotation of arseno bearing minerals from their copper ore has been an interest due to the increasing awareness on protecting the environment by minimizing the possibility of exposed arsenic compound. Some approaches have been proposed, but the mechanisms of separations have not yet fully understood. In this study, oxidation using oxygen was applied. Instead of the complex copper ore flotation results, pure single mineral of tennantite and chalcopyrite foatability was conducted using Hallimond tube. Resembled with the flotation results of copper concentrate containing tennantite, the separation possessed the best result at alkaline condition (pH 11) at where the arsenic content was reduced from 3300 ppm to 1800 ppm. In order to be able to understand the mechanism of the separation atomic force microscope (AFM) was utilized. AFM images showed changes in morphology and behavior when minerals were treated in both acid and alkaline condition. It was found that the morphological change showed the reaction products representing the rate of reactivity of tennantite and chalcopyrite. From the measured force of adhesion, it can be observed that in alkaline condition the surface of both minerals is more hydrophilic than that in acidic condition possessing higher value. This is in accordance with the X-ray photoelectron spectroscopy (XPS) spectra in which hydroxide moieties occupied the mineral surface in alkaline condition while elemental sulfur is in acidic condition."

Jan 1, 2014

By J. Kwon, D. Lee, H. Cho

"The use of the combined grinding and liberation model to predict liberation characteristics of iron ore comminuted by a ball mill was studied. Comminution characteristics were obtained using the one-size fraction method. The iron ore samples were crushed and separated into a number of narrow size fractions by screening. The size fractions were further divided by magnetic separation into three classes: concentrate, middling, and tailings. Subsequently, various size-grade classes were subjected to ball milling, and the results were analyzed in terms of the kinetic grinding model. The mineralogical textures of the grinding products were analyzed using mineral liberation analysis. The distribution of iron content within the size fractions was characterized by the beta distribution combined with the Andrew–Mica diagram. It was found that the grinding characteristics of the iron ore samples varied slightly with the iron content. However, the liberation characteristics were well described by the same set of liberation model parameters, regardless of composition. The variation in grinding kinetics with composition and the liberation model parameters was used in the combined comminution–liberation model to predict the evolution of the size-composition matrix as grinding proceeded. The predicted results agreed well with the experimental results. The developed model can be used to construct the yield–recovery graph and to calculate the liberation efficiency to determine the size reduction threshold for efficient separation. INTRODUCTION In mineral processing, comminution is usually the first step that ores undergo to liberate valuable minerals from gangue minerals. Generally, as the particle size decreases, higher liberation can be achieved. However, excessively small particles are unfavorable to subsequent processes, such as separation. Moreover, comminution is a highly energy-consuming process itself that accounts for approximately 60% of all energy used for processing. Therefore, there is a definite need to increase energy efficiency by applying adequate stress so that a high degree of liberation can be acquired at the coarsest size without overgrinding. To this end, it is essential to develop a model to predict the liberation of minerals as a function of size reduction."

Jan 1, 2018

By Xiaoping Xu, Tiansong Dong, Guosheng Wang

"Jianfengpo tin ore is located in Jiangxi Province, China. The cassiterite is fine and dispersed. It is hard to separate marmatite from a variety of sulfide minerals. Because the iron-containing sulfide minerals including pyrrhotite, pyrite and chalcopyrite are detrimental to the improvement of the grade of zinc concentrate. Besides, the presence of the iron oxides and ferro-carbonate minerals results in the difficult beneficiation of tin. Therefore, Jianfengpo tin ore is a kind of refractory cassiterite polymetallic sulfide ore. According to the properties of Jianfengpo tin ore, the technology process of "Sulphide ore preflotation-Bulk flotation of sulphur and zinc-Separation of sulphur and zinc -Magnetic separation-Gravity concentration" was developed to recover the valuable materials including marmatite, pyrite, magnetite, cassiterite and indium comprehensively. For the feed ore containing 0.87% Sn and 0.70% Zn, a zinc concentrate of 44.56% Zn with a recovery of 69.10%, a high-grade tin concentrate of 54.38% Sn with a recovery of 53.03% and a low-grade tin concentrate of 6.54% Sn with a recovery of 1.25% can be achieved in the batch flotation tests. In the industrial tests, for the feeding which contains 0.55% Sn and 0.65% Zn, the tin concentrate of 49.10% Sn with a recovery of 48.52% as well as the zinc concentrate of 45.11% Zn with a recovery of 60.10% can be produced. Thus some pyrite and magnetite concentrate are recovered as well. So Zinc, tin, sulphur and iron ores are recovered effectively by the technology."

Jan 1, 2014

By P. M. Solozhenkin

"Galvanochemical process (GChP)) cleaning of sewages is realized in the field of shortcirquited galvanic elements from the mixture current the materials place in purification’s solution and form multitude galvanopairs without external electric field in presence oxygen of the air. The galvanochemical process is electrochemical process utilizing galvanic pairs: coke - iron, iron - copper and others and process does not require chemical reagents.The effect of basic parameters of the cleaning effectiveness have been studied depending on oxidizing of galvanopairs. Adjusting nature, type of galvanic pairs and forming three component system possible to enlarge emf circuits to 2.378 V.The role of ?2, as basic agent, for generation of hydrogen peroxide and hydroxyl ions.It was stated, that removing of metal ions from solutions occur mainly on account of sorption and hydrolytic sedimentation of iron oxihydrates.Determined separate stages of the process: coagulation, sorptions of admixtures on freshly formed ferric oxides and oxidizing destruction of organic components of effluents in presence of ?2 ? ?2?2. Shown efficiency of the method for removing of Cu, Cr, Ni, Zn, As ions, as well as fluoride, phosphate and cyanide anions and oil products, surface-active and flotation reagents. Cleaned water can be recycled for some processes non-critical toward residual concentration of admixtures, as total salt contents is lowered on 60-75 % and reaching limits of concentration for toxic components.The concept of high power unit creation was developed, and galvanochemical pulsator is presented. The pulsator is not expensive, and exploitation expences are low, as well as servise is simple with high effectiveness, and capacity. The galvanoflotation process is developing, combining galvanochemistry and flotation of hydrofobic admixtures (oil, surface-active agents).The galvanochemical flotators are presented."

Jan 1, 2003