Search Documents

By J J. F Smith

The application of pneumatically loaded ANFO for underground mining has continued to increase year by year since the technique was first developed and introduced underground during the early 1960's. Improvements in the manufacturing process for explosives grade prills, the design and construction of more efficient AN prill-fuel oil blending equipment, and the introduction of more durable and reliable pneumatic loaders have promoted the wide application of the relatively low cost blasting agent, ANFO.

Jan 1, 1982

By Richard J. Mainiero, Harry C. Verakis, John J. Mulhern

There are application in coal mines where it would be advantageous from a safety stand point to fire unconfined shots. However, the firing of mud caps (adobes) or other unconfined explosive charges in underground coal mines is not permitted because of the explosion hazards associated with methane gas and coal dust. Present safety regulations in Title 30, Code of Federal Regulations prohibit such Practices. Recently, MSHA proposed revised coal mine regulations for the approval and use of sheathed explosives for Public comment.

Jan 1, 1987

By Pierre-Alexandre Abeel, Charles Dowding, Justin Lueker

When blasting is eliminated as a cause of cosmetic cracking, often someone will ask, “If blasting didn’t cause the crack, then what did?” This paper describes detection by remotely operated instrumentation of the new cosmetic crack that was climatologically-induced. The measurement was obtained as a part of the development of Autonomous Crack Measurement (ACM) instruments to measure micro-inch response of cracks to both long-term, climatological, and dynamic, blast vibration effects. The crack occurred in the wall of a structure that was monitored for over 29 months and as such represents one of the longest periods of ACM observation.

Jan 1, 2015

By Douglas R. Burns

Complying with SARA-Title III and the Emergency Planning and Community Right-To-Know Act as a Non-Manufacturing Facility. As of August 23, 1988 non-manufacturing facilities storing end using chemicals which require MSDS (Materia1 Safety Data Sheets) must fi1e with SERC (State Emergency Response Commission), the LEPC (Loca1 Emergency Planning Commission), and the loca1 Fire Department a list or copies of all MSDS sheets with the Tier I and Tier II forms completed.

Jan 1, 1989

By Gungor Tuncer, Ali Kahriman, Umit Ozer, Abdul Karadogan, Mehmet Aksoy, Ertugrul Kaya, Deniz Adiguzel

This research was performed on the quarry that will be opened to produce aggregates and rock filling material at Catalagzi region at Zonguldak providence. Excavations will be done by drilling and blasting. However, there are some structures which can be adversely affected by blasting at the quarry. These structures are a methane exploration drill hole and a house at the distances of 340 m and 390 m, respectively. The one of the main goals of this study is to perform a preliminary assessment of possible damage effect of ground vibrations induced by blasting on these structures by risk analysis based on ground vibration measurements.

Jan 1, 2009

By Charles H. Dowding, Catherine T. Aimone

Rock particle sizes were measured at fourteen steep-slope Appalachian coal mines during production blasting. The distribution of rock sizes shows the effects of inter-hole timing, sequence of hole initiation, as well as charge distribution within each shot. Blast design parameters were selected to: (1) minimize displacement of broken rock conforming to throw control required of mining methods, (2) minimize seismic effects, and (3) create breakage at a cost economical to mining operations.

Jan 1, 1983

By Goran Cirkovic, Zvonimir Ester, Josip Krsnik

During the reconstruction of the motorway Zagreb-Krapina three reinforced concrete bridges were demolished, for their width was not adequate for the new motorway. Demolition of the three bridges was carried out by blasting as duration of the traffic cut on the motorway and the railway was limited to maximally 4 hours. During that period of time the demolished bridges had to be removed. Therefore, very tiny granulation was requested suitable for loading and not endangering the surrounding structures. Before each of three main blasting, trial blasting were carried out including the seismic measurements registering the seismic effects. The nearest residential building was at the distance of less than 30 m from the place of blasting. Additional difficulty was the fact that by each of the three bridges there is a new bridge, with minimal distance between the old and the new bridge being 30 cm. As each of the bridges is of different construction and of various thickness, particular blasting technique has been prepared for each one of the bridges.

Jan 1, 1997

By Abdulkadir Karadogan, Zikri Keti, Umit Ozer, Mehmet Aksoy, Ulku Kalayci

This paper presents an investigation about how the motions of blast induced vibration waves were affected by the presence of the fault planes. This study was carried out at Espey Open- Pit Boron (Colemanite) Mine in Turkey. Within the scope of the study, ground vibration components were measured for 8 shots using 9 vibration monitors, considering the direction of the fault. Measurement stations were located around the fault line that intersects the open-pit mine in the north-south direction and on different benches along the fault plane. Then, the data of the vibration components obtained from the 77 recorded events were analyzed and the results were presented.

Jan 1, 2012

By R E. Langston, S M. Gazioglu

A preconstruction inventory program was conducted to determine the existing conditions of residential, non-residential and all other structures within 2,000 feet of the blasting limits for a highway excavation site in Asheville, North Carolina. Prior to major production blasting, eleven test blasts were detonated to establish site specific propagation parameters in order to develop contours of maximum allowable explosive charge weights per delay. The method of scaling distance by the square root of charge weight per delay was utilized in developing the contours of allowable charge weights. The charge weight contours were revised during blasting operations as additional vibration data became available. The effects of blast induced vibrations on a nearby water storage reservoir, a nearby vehicular tunnel and other adjacent residential and non-residential structures were observed and monitored over a period of two years of blasting operations.

Jan 1, 1980

By John N. Jr Edl

Geokinetics, Inc. has pioneered an in-situ oil shale retorting production process that provides the requisite void space for producing a permeable rubble bed, within the retort zone, by using the explosive energy from vertical blastholes to lift the overburden. By installing suitable instrumentation on the surface of the overburden over an appropriate blasting pattern, it is possible to obtain estimates of the average radius of gas penetration around the blasthole and the average volume, per unit length of blasthole, that is actually occupied by the explosively produced gases (which includes both the volume of the cracks that are penetrated by the gas pressure and the deformed blasthole volume). It is expected that these estimates can be used to examine, and quantify, the effects of such blast design parameters as the type of explosive, the blasthole diameter, the geometry of the explosive charge (length to diameter ratio), and the relative timing of sets of charges.

Jan 1, 1983

By Sterling Ziegler, Kameron Ray

Mining operations at a Wyoming coal mine were progressing to within 300 feet (91 meters) of a high pressure natural gas pipeline. Vibration levels from cast blasting were at a point at which standard designs would exceed permitted limits and could potentially damage the pipeline. Without a confident vibration model, mining would be unable to continue in the pit rendering an entire cut of otherwise mineable coal sterile. To safely blast in the area, linear superposition seedwave analysis techniques were attempted to be used to create a model that could accurately predict the vibration at the pipeline. Four signature holes were fired individually. The four signature waveforms were monitored at eight discrete locations to create thirty-two vibration data points. Two of the monitors were equipped with triggers enabling the calculation of p-wave velocity.

Jan 1, 2018

By R J. Hill

Blasters are well aware of the problems and expense faced when trying to load in wet bore holes; problems of poor coupling and poor density, as well as the expense of higher priced cartridge product. In answer to these problems, I developed a system for dewatering using nozzles with lay -flat plastic liners which I have used successfully over the last few years. I found the system not only gave me better shots than I could have expected in the circumstances, but also dramatically decreased costs. The system has been adopted by two large roading contractors and a quarry operation in Eastern Canada.

Jan 1, 1986

By Salah A. Taqieddin

Blast casting or trajectory blasting, as it is sometimes called, is an innovative mining technique that has been receiving increasing acceptance among operations of surface coal mines and quarries as a means of offsetting the rising cost of mechanical excavation of overburden with a high overburden-to-ore ratio. Many similarities exist between geological characteristics of overburden formations of phosphate beds and the formations that conceal coal seams. Both are sedimentary origin and are removed for mining in an identical manner (i.e. use of a dragline or shovel to strip or cast the overburden aside).

Jan 1, 1997

This paper is written in response to a request from the UTRC Committee on Perimeter Control Blasting. That Committee is conducting "follow-on" research on the selection of appropriate blasting designs and products for perimeter control of rock excavations. This paper will deal with the rock mechanics principles which affect the outcome of such blasting, and explain to the reader how to apply techniques which will modify the typical site response one would expect for conventional blasting methods. For convenience of reference, and to emphasize the important concept that the application of this technique is site specific, that is it must be custom-designed for each site, the technique is being called "Modified Site Response Blasting".

Jan 1, 1984

By Jack Eloranta

Building on previous work, this paper expands the template for modeling the economic relationship between blasting and grinding. The actual efficacy of various blasting enhancements is not addressed, however, placing costs and potential benefits in proper context should aid in designing mine/mill optimization trials.

Jan 1, 2014

By Michael Wieland

Sharp transient stress waves generated during the delay blasting of underground coal can damage unfired borehole charges remaining in the delay pattern. These tremendous stress pulses in coal bear a strong resemblance to underwater shock waves, despite differences in rise times, damping rates, and scaling relations. "Shock wave" terminology is adopted to distinguish the sharp transient waveforms propagating through the coal from the gas-driven stresses that rift the coal. Reported waveform characteristics of shock waves through underground coal were utilized to design a simulator test for rating the impact resistance of cap-sensitive explosives. Theoretical minimum borehole separations were determined for each cap-sensitive explosive from the requirement that worst-case waves hitting an unfired charge would not exceed its impact resistance rating. Rugged explosives have higher impact resistance and will function properly at smaller borehole separations. Additional work is required to verify the findings from the simulator technique and modeling relations reported here.

Jan 1, 1990

By P A. Gibson, J R. Brinkmann

The South African gold mining industry fires approximately 800 000 sloping blastholes daily. A programme aimed at characterizing the stope blasting process is underway in order to identify areas for improvement and to provide blasting related information for the design of mechanized sloping systems.

Jan 1, 1985

By Raymond H. Green, Mitchell W. Green

The authors examined the application of precise millisecond delay electric blasting at a well-known Vermont quarry. The paper explains how the use of a new high-accuracy electric delay detonator has improved fragmentation, raised productivity 10%, simplified blast design, and increased the ability to predict results from blasting.

Jan 1, 1986

By Kfw Eick

The paper describes the use of the Nonel millisecond delay blasting system in narrow, deep, tabular ore bodies and briefly describes the standard stoping method as used on Harmony Gold Mine and compares this with the new Nonel short panel system.

Jan 1, 1990

By Kai Nielsen

A model has been developed for sensitivity analysis of open pit bench blasting. The model simulates the cost effectiveness of various blasting designs in relation to the equipment used for drilling, loading, hauling and primary crushing. The simulations will give an indication of the optimum powder factor giving the lowest over-all costs for drilling, blasting, handling and crushing.

Jan 1, 1985