Search Documents

By Blair Jackson, Tjaart Louw

Martha Mine, owned by Newmont Mining, Australia appointed Macmahon Contractors (NZ) Ltd as the mining contractor to drill, blast, and crush and convey ore for processing, followed by construction of a tails dam facility from the waste material. The open pit is located 140km(90miles) south east of Auckland, New Zealand in the middle of the township of Waihi (the main street of the town with a population of 3,500 is 90m from the perimeter of the open pit mine). Mining must proceed at 325,000m3 (of which involves blasting approximately 11,000 holes per month, in order to ensure continued ore supply.

Jan 1, 2003

By Dirk van Zyl

Rock fabric information is often available from drill hole information and bench face mapping. An approach is presented to predict fragment size distribution of blasted material from this information as well as that obtained after the blast. The following information available from a mineral exploration drilling program was used in the prediction of fragment size distribution: largest piece, percent particles larger than 1 inch and RQD. Photographs of bench faces were used to estimate the fragment size distribution. Fracture spacings were evaluated along a series of parallel lines on the photograph. Photographic techniques were also used to obtain the grain size distribution of blasted material. m is paper describes the methodologies applied in some detail.

Jan 1, 1986

By S C. Alford

Explosive fracturing of metal is usually considered to be an imprecise process but, by careful consideration of shock-wave geometry, precise results are obtainable. The limited development of such charges is attributed to experimental difficulties. A charge configuration has now been devised in which a prismatic wave-shaping element is used to resolve the shock-waves entering a target plate into two convergent components. The extreme pressure caused by their collision initiates a diamond fracture in the proximal target face, and coincidence of reflected tension waves generates a fracture in the distal face. A combination of these effects breaks the target. An embodiment of S.R.T. is described which is flexible, magnetic and contains no cavities.

Jan 1, 1986

By Dale S. Preece

A discrete element computer program, DMC (Distinct Motion Code), has been used for several years to simulate blasting-induced rock motion. Recent enhancements of DMC's capabilities have included addition of an algorithm that couples together rock motion and gas flow. This allows the user to specify a particular explosive which also specifies equation-of-state and other parameters necessary to model explosive gas flow from the blastwell. Rock loading by the flowing gas is calculated automatically. The mechanism for calculating the rock loading is the subject of this paper. The rock motion effects the gas flow calculation by changing the porosity. DMC is currently being used on a SUN SPARCstation 2 computer workstation.

Jan 1, 1993

By Joshua Hoffman, Catherine Johnson, Braden Lusk

The practice of dual initiation using precise timing from electronic detonators in boreholes is thought to be beneficial for increasing fragmentation at a desired location in the rock strata. This increased capacity for fragmentation is understood to be a product of both the collision of detonation waves in the explosive column and an increased energy liberation rate, each resulting from dual initiation. In addition, the collision of shock waves from two adjacent blast holes is suggested to improve fragmentation at the location the two shock waves meet, which can be controlled with precise timing. This paper presents the results from scaled laboratory experiments where converging detonation waves and shock waves were studied.

Jan 1, 2014

By P. R. Mohanty, Kaushik Dey

Blast-induced tunnel overbreak prediction in the past has been based on peak particle velocity measured far from the blast site with necessary extrapolation. This has often resulted in suggesting higher damage threshold levels of Acceleration/PPV for overbreak prediction (Bogdanhoff, 1995, Holmberg and Persson, 1997, Murthy and Dey, 2002). These, site-specific far-field blast vibration studies, have also revealed that predicted PPV levels for overbreak could lie in the range of 700-5000 mm/s, an extremely wide range to generalize. Experimental blasts were conducted, in an underground metal mine located in eastern India, with an objective to study the level of acceleration /peak particle velocity generated in tunnel blasting. Accelerometers and tri-axial geophones with measuring ranges upto 500 g, 254 mm/s respectively, were mounted on the tunnel floor close to the blast face, with sensor distances varying from 15.25m to 36.10m. Due to straight faces the measuring distance could not be reduced further anticipating, in particular, cable damage. The equipment used was of M/s Instantel Inc., Canada. The blast pattern used was burn cut with large dia relief holes providing the required free face. The blast hole depth was 1.8m. Tunnel overbreak was measured using a telescopic offset rod fabricated at Indian School of Mines, Dhanbad, India.

Jan 1, 2004

By Thomas Bakley, Rob Lee, Jay Rodgers

The present state of technology in Controlled Blasting uses standard explosives’ products to create a crack between holes along a desired line of break. The resulting pre-split, post-shear or cut line is often of variable quality with unwanted damage at right angles to the desired cut line. A new concept in Detonating Cord manufacturing has provided a radically different performing explosive. This new Cord has reduced the Velocity of Detonation by more than a third. It changes the Detonation Pressure proMe of Detonating Cord to a lower and longer sustained pressure pulse. In addition, it develops more gas than conventional cords. At the same time it maintains all of the handling and reliability advantages of conventional Detonating Cord.

Jan 1, 2001

In situ, most Taconite is heavily pre-fractured; because of the high cost of comminution of taconite, maximum fracture of pre-existing blocks is desirable. Sustained borehole pressure plays a significant role in fragmentation, especially by penetrating pre-existing fractures. The distribution of explosive-induced energy in the burden in three dimensions was calculated. Data on the comminution of single particles was used, with the distribution of energies and the distribution of pre-existing block sizes, to calculate fragmentation for a case study. The calculation agreed well with the measured fragmentation. Sequential comminution events are much more efficient than single ones, and enhanced fragmentation may be possible with alternative blasting practices. Some important factors in the dependence of comminution on energy input are discussed.

Jan 1, 1995

By Lawson J. Taylor, Paul N. Worsey

Recent reputable evidence conclusively indicates that conventional chemical delay elements in delay detonators are notoriously inaccurate and can thus seriously affect blasting efficiency.

Jan 1, 1983

By C H. Dowding, P W. Linehan

Many of the technical and non-technical or human problems associated with blasting can be minimized through a proper preconstruction test-blast program.

Jan 1, 1986

By Jerry R. Wallace

A systematic, team approach to pre-blast and on-going problem solving contributed to the successful completion of this indoor industrial construction blasting project.

Jan 1, 1995

By Michael M. Jackson

"The mining industry has for some time compared explosive energy requirements to theresults obtained using ANFO. Drill patterns, powder factors, and explosive bulk strengthshave all been developed based on the detonation characteristics and blasting resultsexhibited by ANFO. However, there are some mining applications where the use of ANFOcan cause over_blasting if loaded to acceptable collar heights or surface breakage problemsif collar heights are reduced. A specialized, low strength, low density water gel explosivehas been developed that has loading densities in the range of 0.4 to 0.7 g/cc. The uniquecharacteristics of the low density water gel explosive is that the explosive can beformulated with a range of available bulk strengths while maintaining excellent detonationsensitivity for use in applications involving ore/waste control, restricted blast patterns,small bench heights, etc. The"

Jan 1, 1993

By Steven D. Sandbrook

A man by the name of Louis Binstock once said, “Too often the shortcut, the line of least resistance, is responsible for evanescent and unsatisfactory success.”

Jan 1, 2015

By Daniel Moroz

This paper will provide an informative overview of the types of explosives and the various methods employed to control avalanches within the boundaries of major ski resorts.

Jan 1, 1991

By Ronald R. Rollins

A continuous propagation velocity measurement probe has been utilized to determine velocities of slurry explosives, whole prills, crushed prills, aluminized crushed prills, in bulk and plastic screw tubes.

Jan 1, 1984

By J J. Mullay, G W. Anderson, C J. McFinley, J F. VanNorman, C J. Kefer

Previous work has shown that testing of precompression effects conducted on a small scale under simulated field conditions in actual rock provides a reasonable model for the evaluation of explosives and initiators under the adverse conditions encountered in production blasting. Using this methodology can result in greater understanding of the phenomena as well as the ability to predict performance. This effort has been extended to evaluate various parameters not previously studied in a controlled fashion. The present paper describes the use of this technique to study the effects of delay timing on precompression effects. Intervals from 25 to 150 milliseconds are included in the study. Both VOD measurements and damage estimates are utilized in the evaluation. The results demonstrate that timing delay between holes is quite important in determining the overall effectiveness of a blasting program.

Jan 1, 1994

By Richard Scales, Giles Hellyer, Ian Travers, Dean French, Peter Bellairs

"The Mt Whaleback iron ore mine is located in the Hamersley Province situated about 1OOOkm to thenorth of Perth, the capital city of Western Australia. A small but significant portion of the waste in Mt Whaleback presents problems due to its ability to react with normal commercial bulk explosives resulting in premature detonations, two of which occurred at the mine in 1983 causing great consternation as well as disruption to the mining operation. The techniques and procedures developed to overcome this problem were based on the use of tough durable, acid and heat resistant liners to provide a physical barrier separating the explosive from the rock togetherwith the development of an accurate down the hole remote temperature logging technology. The liner technology was developed due to the inability to produce a reliable inhibited ANFO despite exhaustive mine based testwork."

Jan 1, 1999

By Calvin J. Konya

Many controversies and differences of opinion exist in blasting technology. The primer location in small diameter dynamite columns is an example of one of these controversial areas. It is generally agreed that in rotation firing of small diameter blastholes, primer placement near the bottom of the borehole is beneficial since it reduces the likelihood of cutoffs. The controversy results in the actual location of the primer in the bottom of the blasthole. Some references indicate that the primer cartridge should be the first cartridge in the bottom of the hole, with the cap pointed toward the collar of the hole. Others indicate that performance is improved with no sacrifice in safety by placing a tamped cartridge first in the hole, and the second cartridge being the primer. The following investigation provides some factual data for consideration.

Jan 1, 1980

By John Petty, John Loviza

Single sentence describing content-- "The best ally an Explosives Engineer can have in a court of law is a regulations enforcer stating all codes and standards were met on a jobsite".

Jan 1, 1996

By Larry D. Lawrence, Gerald W. Greenway

Corrugated boxes have been the dominant shipping container for packaged commercial explosives for the past 3 decades. Recent changes in shipping regulations have dictated to the industry the adoption of enhanced standards dealing with the construction of fiberboard shipping containers for explosives. Effective October 1944, all shipping containers used for explosives will require individual certification verifying that the containers conform to the United Nations performance oriented packaging standards. The U.S. Department of Transportation will continue to enforce compliance to the new UN standards. A renewed emphasis on the design of corrugated shipping containers to insure industry compliance to the UN standards has been a joint development program between the explosive manufacturers, fiberboard container suppliers and the academic community. Along with drop strength, leakproofness, and vibration resistance, the individual stacking strength of corrugated shipping containers has come under tight scrutiny based on the new UN standards.

Jan 1, 1994