Search Documents

By Janos Foldesi, Calvin J. Konya

The determination of the number of primers necessary to efficiently initiate an explosive column charge is essential to good blasting. If the number of primer is insufficient, the total energy stored in the main charge will not be released. On the other hand, the use of too many primers will be counterproductive and raise the blasting cost. Tests were conducted by the authors to determine the correct priming procedure for a basalt quarry. This paper describes the results of those tests.

Jan 1, 1976

By Jorge Cárdenas, José Luis Hurtado

The critical distance determination test through direct recording for the mine in Phase 03 was carried out in January 2024, and in it the vibration and pressure models were obtained for the Sedimentary breccia unit. The method of obtaining the records is based on the capture of individual pressure waves generated by distant loads, sequenced in periods of 600 ms for easy identification. The test set up corresponds to a variation of that used to obtain the vibration model, and uses 08 wells for loads and 04 for instrumentation. The results apply a safety factor of 1.2 and 1.5, being 16,000 PSI and 13,250 PSI respectively. The values are valid for any distance greater than 5.5 m, this being the minimum established between wells for loads according to the configuration defined in the field, also considering that in 5.0 m of instrumentation the section of the drill hole with the sensor called S1 collapsed. The results of the analysis of the test, generated with Heavy Anfo 82 explosive, with a final density of 1.15 g/cc, are presented. The results of the modeling and generation of the graphs and tables presented show behavior in line with the concept of scaled distance. It is important to consider that in water conditions there is a high impact by the condition, which causes the records to be higher than those expected in dry conditions and present less variability. It is for the above reason that the row corresponding to distance with safety factor 1.5 is declared valid. The results are only valid for the rock analyzed, whose medium is homogeneous and constant in terms of lithological composition and that present similar resistance characteristics, fracture frequency and water table levels. As future steps, the objective is to quantify the increase in pressure generated between wells by analyzing time and sequence factors. This analysis aims to explain the occurrence of dynamic pressure events in areas where critical safety distances are observed.

Jan 21, 2025

By Ruilin Yang

Explosive blasting is a widely used method for rock breaking, recognized for its energy efficiency and cost-effectiveness. Despite its advantages, the efficiency of blast energy can vary significantly between different blasts. This paper introduces a new blast efficiency index to assess the energy efficiency of rock blasting, incorporating factors such as explosive consumption, the energy required for fragment surface generation (based on fragment size distribution), and the strength reduction of rock fragments due to blasting. Several examples presented in this paper demonstrate the calculation of the blast efficiency index using data from the literature. The findings indicate that blasting may be the most efficient method for rock breaking compared with direct mechanical techniques of rock breaking used for excavation. On the other hand, blasting is much less efficient compared with the controlled fracturing, such as the cleavage and fracture toughness testing, which highlights the significant potential to further enhance the efficiency of explosive energy usage for rock fragmentation during blasting. The proposed blast efficiency index can be integrated with advanced blast modeling techniques to optimize blast designs, thereby increasing the effective utilization of explosive energy for rock fragmentation and fragment strength reduction.

Jan 26, 2026

By Stewart A. Silling, D. Lynn Gordon, C. Mick Lownds, Dale S. Preece, Ali Bhuiyan, Patrick R. Bowden

Blast heave modeling and prediction utilizing the new discrete element model, GEM, that treats rock as elements with alternating arcs and line. Explosive loading of GEM elements is accomplished by utilizing the Noble-Abel equation of state to track the gas pressure from detonation through expansion to atmospheric pressure.

Feb 1, 2020

By Donald Little, Larry Unger

This paper will give a detailed insight into hard rock, large diameter surface blasting including some practical tips to improve blasting practices. These tips will be non-technical, of the nuts and bolts type, intended to help the man in the boots. The paper will begin with the importance of communication between the engineering department and the blasters. What looks good on the mine development map might not blast very well. Tight inside corners, 90 degree outside corners, too few rows; are a few of these problems.

Jan 1, 2006

By Barbara Rutter, Phillip Mulligan

This research investigates how changes in shock tunnel geometry affect the pressure versus time waveform. The Large Arena Test Simulator (LATS), which is composed of four different rectangular sections connected by three expansion sections, was used to determine how the changes in geometry affect the shock wave profile.

Feb 1, 2020

By Dale S. Preece

A Discrete element computer program named DMC (Distinct Motion Code) has been developed for modeling rock blasting. This program employs explicit time integration and uses spherical or cylindrical elements which are represented as circles in 2-D. DMC calculations have been compared with measurements on bench blasts in the field with relatively good comparison. Structural geology and joint sets have a significant impact on any blast and DMC has not, until now, included these effects. This paper discusses a recently added DMC capability for treating joints and bedding planes in bench blast simulations.

Jan 1, 1995

By Calvin J. Konya

The Woodville Lime and Chemical Company Limestone Quarry is located in Sandusky County, Ohio. Fifty years ago, when quarrying began, it was situated approximately two miles from the town of Woodville. Today new houses border the quarry property within 1,500 feet of one of the working faces. During the past two years, the operation has systematically changed the blasting program to achieve better fragmentation, lower costs, and to maintain good relations with the local property owners. This paper will discuss systematic changes made in the blasting program to increase productivity and reduce costs.

Jan 1, 1977

By Tapas Kumar Mukherjee, Sujit Kumar, Sanjay Kumar Singh

This paper dwells on the epic blast conducted at Tata Steel’s captive coal mine in India and the insights drawn from it. Optimal blast design parameters had to be ascertained for operating benches (6.56 yards (6 meters) to 16.40 yards (15 meters)) where shovels and mining pay-loaders are deployed. Better fragmentation and suitable muck profile with controlled vibration levels were the pre-requisites. The landmark blast was carried out at Quarry-AB, West Bokaro on 17th March 2017. The colossal blast was done with 275 US ton (250 tonnes) of explosives poured down 1074 drill holes of 6.5 inch (165 mm) diameter. This blast is unique from the perspective of vibration control as it was conducted near local villages situated beyond 546 yards (500 meters) but within 601 yards (550 meters)) from the blast site. The entire array of preparatory activities had been successfully and impeccably executed within the same day. The optimization was achieved through meticulous coordination between TSL team, M/s Solar and M/s IEL. When a rock is blasted, numerous interactions occur among granular particles which are impacted by rock mass properties, explosives properties, blasting geometry and the detonation timings. Optimized use of resources requires a better understanding of these interactions. Extensive field studies have shown that blast fragmentation and suitable muck profile influences the performance of downstream processes in a mine. Consequently, profitability of whole mining operation can be greatly improved through optimized fragmentation. For arriving at the best blast geometry, several blasts were conducted with differing ‘burden and spacing’ design and charging pattern at various loading benches of the mine. Eventually, the largest ever blast was successfully carried out. This accomplishment is the culmination of the insights derived, confidence built, and expertise evolved through a progression of larger blasts conducted earlier (202 US tons (184 tonnes) and 143 US tons (130 tonnes) respectively) by the same team. All blast parameters were within the recommended level and no adverse impact on nearby structures was evidenced. In-the hole VOD of different explosives was determined and placement of boosters was standardized. The signature blasts were conducted to optimize the delay interval between the holes in a row and between the rows. Blasting parameters were fine-tuned in alignment with the desired fragmentation level and muck pile profile conducive to smooth and expeditious loading and hauling by mining HEMM. Rock fragmentation analyses were carried out using photo-analysis system. The insights gained from this blast would serve as the cynosure for planning and carrying out more such blasts with highly optimized parameters in the future with the intent of improving mining efficiency and productivity

Jan 1, 2019

By H. S. Venkatesh R. Balachander, G. C. Naveen

During the construction of a 1020 MW underground hydroelectric project in Bhutan a huge rock fall took place in the Downstream Surge Chamber (DSC) during March 2016. The total quantity of rock in the fall area is estimated to be about 1,50,000m3 (2.6 billion cubic feet), out of which about 25,000m3 (0.44 billion cubic feet) of muck was removed. The removal of muck was stopped apprehending that the cavity formed due to the rock fall may get further aggravated leading to widening and destabilising the adjacent transformer hall cavern or it might day light as the top cover was about 190m (623 feet). As the fall has virtually blocked the 314m (1030 feet) long cavern and divided it into two different chambers (south and north), and that the muck cannot be disturbed, it was decided to erect concrete wall on either side of the fall up to the cavern roof and then later address the filling of the cavity with appropriate fill material. As the access to the DSC was there for the southern side it was decided to extend a cable tunnel which was terminated at a distance on the north side of the cavern by D&B so that once it gets punctured into the north wall of the DSC it can be used to access the fall from this front too. This is a unique situation where in every blast approaching the DSC, the parting between them is diminishing and hence the tunnel blast will be exerting axial load on the parting wall leading to dynamic transient loading conditions and buckling may take place on the northern wall of DSC. This paper describes the various drill blast combinations adopted for successful excavation of this tunnel.

Jan 1, 2019

By Paulo C. Fernández A, Sergio Matamala V, Claudio C. Gajardo, Christian A. Rees P

In fragmentation processes in open-pit mining, it has been observed that there are many opportunities for improvement if greater control of ore displacement in blasting is achieved, reducing the percentage of mixing between ore and waste material (dilution) through the integration of new technologies that allow its quantification and optimization of extraction polygons. This work investigates the relevance of the initiation sequence and direction of displacement in blasting in relation to ore dilution and the potential benefits of process optimization. A three-dimensional modeling tool was used to evaluate movement control optimizing the extraction zone based on the maximization of ore recovery. The study was made by iterating different scenarios, by varying only the initiation sequence and inter-hole delays. To validate the displacement simulation, a total of 10 blasts were carried out for calibration, obtaining a level of agreement between the simulation surface and the actual topographic survey of 80% or higher. The analysis included horizontal and vertical displacement, quantification of swell and dilution within extraction polygons for different scenarios, and informed decision-making based on ore control. The results clearly indicate that by modifying the blast initiation sequence, greater control over dilution in ore/waste transition areas is achieved, thus optimizing the recovery of the planned material and maximizing the ore grade. The use of this type of simulation tools allows for the generation of extraction strategies based on the value of the polygon, unnecessary displacements in the free face, optimal loading fronts, etc., maximizing the recovery of ore and stockpile material, complying with the planned tonnage and ore grade for each extraction polygon, delivering added value to the chain and emphasizing the importance of adding new technologies to the mining industry that allow for the optimization of processes to maximize profits.

Jan 26, 2026

By Catherine Johnson, Barbara Rutter, Phillip Mulligan

Shock tubes, shock tunnels, and blast tubes have been widely used by explosive researchers and shock wave investigators to understand the characteristics of shock waves. Rectangular, cylindrical, and conical are the three simple geometries commonly used in shock tube and shock tunnel testing. These geometries result in shock waves that resemble the Friedlander curve’s simple exponential decay. However, geometries that are more complex have not been studied. This research investigates how changes in shock tunnel geometry affect the pressure versus time waveform. The Large Arena Test Simulator (LATS), which is composed of four different rectangular sections connected by three expansion sections, was used to determine how the changes in geometry affect the shock wave profile. Shock wave profiles were measured inside and outside the LATS to investigate the geometry’s effect. A representative shock wave profile from each geometry and open-air explosive testing were compared visually showing the geometries effect on the shock wave profile. The LATS produced a waveform with four pressure peaks behind the initial shock front, which were found to be associated with the four rectangular sections. The resulting pressure trace was compared to pressure traces from simulated urban bombings. The number of turns in an urban environment equated to a new peak, which is caused by additional expansion sections of the shock tunnel. From this observation, complex geometry shock tunnels can be purpose built to simulate an explosion in an urban setting. The use of shock tunnels with complex geometry in simulating urban bombings can allow for numerous representations and a better understanding of profiles produced during an urban bombing or similar scenario.

By Braden Lusk

A typical rural house surrounded by a surface coal mine was instrumented in 2008. Information regarding ground vibration, airblast, and sounds inside the house was collected. Previous publications have included conclusions about this data with regard to blasting source (far-field or near-field) and results as to how the residents experience the blast were made. Several events were also recorded that were not related to blasting due to the nature of the trigger system. The trigger of the monitoring system was attached to one of the mid walls of the house, thus other normal daily events produced vibration levels significant enough to trigger the monitoring system.

Jan 1, 2011

By Douglas Rudenko PG, Jay Elkin, Siavash Mahvelati Ph. D.

Very little studies have investigated the behavior of cracks in unlined tunnels over long periods of time, especially when such flaws are subjected to blast-induced vibrations. Using a pool of 30+ blast events, a positive correlation was found between the peak particle velocity and peak crack movement.

Feb 1, 2020

By J. Silva, M. Kotraba, F. Pontanilla

Blasting is the application of highly complex science that, in some cases, could be viewed as an art. Many variables are involved in a blast, including geology, pattern design, timing and firing sequence, and explosives selection. Assuming that better results can be achieved by only increasing the powder factor is inaccurate. The Drill-to-Mill (D2M) concept has been in the mining industry for over two decades. The D2M approach is commonly viewed in an oversimplified manner, assuming that by simply increasing drilling and the amount of explosives used (both of which add operational costs), the downstream value will be created. An optimized D2M initiative should combine the smart application of explosives at the beginning of the mining process, matching the dynamic properties of the rock to the explosive selected to improve the efficiency of the energy created by the explosive to the rock mass being blasted, and to bring benefits to the mining operation across the entire mining and processing value-chain. This paper reviews the principles behind matching the shock impedance of the rock and the explosive and compares the traditional use of explosives versus the smart application for two hypothetical blasts.

Jan 1, 2024

By Scott King, Norm Patterson, Ruilin Yang

The multiple blasthole fragmentation (MBF) model developed by Orica models the contributions from multiple blastholes to fragmentation at any given point in the rock and simulates a production blast with the actual geometry of the blasted overburden and free faces, explosive loading, multiple decking, and delay timing of each explosive charge. The model has been successfully applied to several open pit mines and quarries around the world, including Canada and the United States. The peak particle velocity (PPV) induced in the rock from the explosive detonation is used in the MBF model as the key parameter relating to the size distribution of the rock fragmentation. Relating the PPV to the rock fragmentation is based on earlier work relating the particle velocity to the dynamic strain in rock. A recent publication further revealed that the PPV is related to the maximum relative displacement that induces three dimensional strain at a point in the rock. The model can explicitly model most of the blast design parameters including explosive properties.

Jan 1, 2018

By J. A. Sanchidrián, P. Segarra, S. Gómez

Blasting is a common activity in mining that can cause significant damage in the remaining rock mass. The most commonly used method for predicting vibrations is the Swedish or Holmberg-Persson approach. It is a simple and fast method that uses empirical formulation to estimate the vibration levels based on the explosive charge weight, distance to the source, and other parameters. However, it has limited accuracy and does not consider the effect of free surfaces or other boundary conditions. On the other hand, recently developed methods as the full-field solution (FFS) can provide more accurate predictions of vibrations due to excitations provoked by cylindrical columns of explosive, but the inclusion of free surfaces in analytical methods is a challenging problem. This paper presents a new approach that includes free surfaces in the FFS to predict vibrations analytically in the near-field. The main obstacle to including free surfaces in the FFS was the belief that the solution was non-decoupleable in P- and SV-waves separately. The Heelan's approach was previously used to decouple them, but it only provides valid radiation patterns in the far-field and does not account for intrinsic attenuation. In this paper, we address this problem successfully, allowing for the inclusion of free surfaces in the FFS.

Jan 1, 2024

By Ingvar Hansson, Bjorn A. Jonsson, Bernt Larsson

In the Kiruna Research Mine, Sweden, four large open stopes have been mined, leaving intermediate piIlars and crown pillars. At the final stage of mining mass blasting of the crown pillars above two of the stopes was carried out. The crown pillars contained some 290,000 tons of iron ore. In the mass blast a new initiation technique was used, utilizing the new non-electric system NONEL ? UNIDET. The blasting technique including vibration control is described. The mass blast resulted in high recovery, good fragmentation and low vibration levels.

Jan 1, 1986

By Thomas M. Keevin, Gregory L. Hempen, David J. Schaeffer, John M. Jr Pitlo

Repelling charges are small explosive charges detonated to frighten and drive fish away from a blasting zone just prior to detonation of a major explosive charge. Use of repelling charges has been recommended by natural resource agencies to mitigate the effects of submerged explosives. Blasting companies have used this technique in a "good faith effort" to reduce potential damages to aquatic resources. It has been assumed that noise or pressure generated by the small charge will drive fish from the immediate area, thereby reducing impacts from the much larger and potentially more-damaging blast.

Jan 1, 1997

By Brian Lewis, Reinhold Daykin Schnell

Blasting specifications and guidelines are very important aspects of detailed project specifications covering any scope of work (SOW) that involves explosives and blasting procedures. A lot of larger construction or tunneling projects require some degree of project specifications for the entire scope of work on such project, including blasting specifications. It is important that all blasting specifications effectively and accurately address all explosives and blasting concerns associated with the SOW for such project. This includes safety and security, required personnel and their associated responsibilities, procedures and applications involving explosives, blast design and planning, blast monitoring and reporting, quality assurance and quality control, and local, state, and federal regulations and limitations. With the of wide range of information required in blasting and overall project specifications along with the risks associated with work involving explosives, it is also important to ensure qualified personnel are involved in interpreting or compiling and approving any blasting specifications and guidelines. The purpose of the following paper is to explore and present the basic information, as summarized above, that should be included and considered in the creation of detailed blasting specifications and guidelines. Detailed information is presented in specific relation to a potential bid package that would be compiled for a construction or tunneling project requiring protective or high-profile blasting.

Feb 6, 2023