Search Documents

By Claude Cunningham

Simple bulk energy rating of explosives obscures the realities of how these deliver their energy, and diverts attention from the key question of controlling blasting results. Explosive performance is directly related to the pressure pulse impacting on the blasthole wall. This is helpfully visualised by comparing the adiabatic expansion plots for explosives of interest on the right scales and axes. The simple comparison of a pure emulsion with pure ANFO illustrates the practical significance of the intrinsic behaviour of these opposed formulations, showing that the emulsion can be expected to work more by softening rock, while ANFO will tend more to crack it. The explanation for these differences lies in the high shock, low sustained pressure of the former relative to the latter. The technique is readily applied, if a good detonation code is available and able to swap data into a spreadsheet. Any differences between codes will emerge most strongly in comparing the gamma plots.

Jan 1, 2002

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By Jorge Flores, Benjamin Cebrian

Blast Optimization at a high altitude mine operation involves not only the selection of the right drilling designs and explosives but also the circumstances of operators working at low oxygen levels and low temperatures.

Jan 1, 2015

By E. Vilaescusa, J. Eloranta

The work presented in this paper investigates the influence of non-ideal detonation characteristics related to the blasthole diameter, base emulsion sensitivity (micro-balloon sensitised versus unsensitised) and percent emulsion on the explosive shock energy available to break rock using ANFOemulsion blends. A series of theoretical equal powder factor bench blasting patterns with hole diameters of 127mm (5”), 140mm (5.5”), 152mm (6”) and 165mm (6.5”) are compared to assess the non-ideal confined shock-state work energies. The Non-Ideal Shock Energy Factor (NSEF), which is the available shock energy per cubic meter of blasted material (MJ/m3) or kilocalories per cubic yard (kcal/yd3), is used to compare the different blasting patterns charged with a range of ANFO-emulsion blends from zero to 50% emulsion.

Jan 1, 2012

By Norm Disley, Kingsley Hortin, Gertjan Bekkers

As part of the expansion of the Kidd Creek Mine to 2,682 meters (8800 feet) below surface, two largediameter 3000kW (4000HP) booster fans were installed at the 6000 level. Shortly after commissioning the fans, significant damage to the fan bearings were observed, forcing several shutdowns for repairs, which were very disruptive to the mine’s production process.

Jan 1, 2008

By D. Scott Scovira, Rick Webber

The Iron Ore Company of Canada [IOC] is a global leader in Arctic mining applications, and the blasting crew have something to be very proud of. On Wednesday 21 Dec 2005 at 3:28 PM the largest single bench blast in the company history was detonated. The successful firing of this 5.0 million tonne [5.5 million ton] blast surpassed the previous company record of 3.8 million tonnes [4.18 million ton].

Jan 1, 2008

By Paul V. Sterk

In the early 1980's, the Homestake Mine converted from labor intensive methods such as open cut-and-fill mining to Vertical Crater Retreat (\/CR) bulk mining and mechanized cut and fill. This transformation occurred as a result of high costs and low productivity associated with open cut-and-fill mining. Use of Vertical Crater Retreat allowed Homestake to contain waste development rock within the mine to further decrease costs since the voids created from VCR stopes provide a good receptacle. The need to access these voids from surrounding development to facilitate waste dumping precipitated the development of drop raising. This system is cheaper than raise boring because it allows drilling into the top of an open stope without the expense of raise boring cutouts or equipment. It's safer than conventional raising since access from the bottom is not required. Two methods of long hole raising or "drop" raising have been successfully developed at the Homestake Mine and can be categorized as Ring Drill Drop Raising using 2-1/4 inch holes and VCR Drop Raising using 6-1/2 inch holes.

Jan 1, 1991

By Thierry Bernard

New technology to automatically design a blast based on autonomous drone. The process of flying a drone, calculating the 3D cloud of points, generating the critical face profiles and placing holes automatically according to burden specification becomes fully automatic. A nice time saving with more efficiency

Feb 1, 2020

By Radhe Krishna, Mutale William Chanda, Timothy Mwale

Blasting as a process is the emplacement of industrial explosives into blast holes suitably located to a free surface and detonated. Every blast hole containing a certain amount of explosive charge undergoes impulsive loading when detonated and results in the dynamic transfer of a powerful shock wave to the surrounding rock. It is the shock wave that brings about rock breakage when the tensile stress produced upon reflecting from the change in material density or free face overcomes that of rock material tensile strength. However, this shock wave comes along with unwanted destructive consequences such as damage to remaining rock, ground vibration, noise and fly rock. The above mentioned consequences pose a great threat to the Community of Wusakile, Kitwe as Mopani Copper Mines Plc wishes to increase its production by expanding the pit towards the community that lies within 150 m (164 yd) from the pit rim. As a requirement from the Zambia Environmental Management Agency (ZEMA), all blasting operations close to the community must maintain at least below the maximum vibration threshold of 10 mm/s (0.3937 in/s) PPV-Peak Particle Velocity or else risk closure of the mine (AMC,2009). In order to satisfy the above statement, a good understanding of explosives is required. This paper therefore presents the phenomenology of rock breakage by explosives with much emphasis on electronic blasting and how best this process can be controlled in densely populated communities. Factors affecting maximum projection distance such as, size of the fragment, shape of the fragment, angle of projection, the state of confinement of an explosive charge, were also studied. In addition, design faults, deviation in implementation and unforeseen geological conditions were also considered. The paper discusses the above facts based on research.

Jan 1, 2015

By Seokbin Lim

According to published literature, the equation of motion of linear shaped charges (LSCs) has been investigated as early as the 1960s in a few research organizations. However, due to the comparatively low penetration performance, the amount of research has not been extensive, and the use of this device is quite limited in very specialized applications. Traditionally, the equation of motion of an LSCs’ liner shares the same basis as conical shaped charges (CSCs) because they are under the same functional category and generally have similar geometric configuration. However, the nature of LSCs is not quite similar with that of CSCs due to multiple reasons, and they required a new set of equations to properly address their performance. In this paper, we reviewed different sets of approaches in describing the liner collapse behavior of LSCs mostly based on the author’s contributions.

Jan 1, 2014

By Alastair Torrance, Gary Cavanough

Over the past two years a research project has been performed on reactive and hot ground. A key finding is that host materials including carbonates and coal are inhibitors to the reaction of sulphide and nitrates. The mechanism of this inhibition is pH buffering and isolating the surface of sulphide from reactants. It has been identified that acidity is a key driver of the reaction with a pH of 2 required for a reactivity event. A series of decomposition experiments confirmed that reactive and hot ground are essentially the same phenomenon with the heating produced either by the reaction of sulphide with nitrates or an external heat source. The results indicate that the key driver of detonation in reactive ground is energy and heat released from the acid induced reaction of sulphide and nitrate with no indications of sulphide being a catalyst or contributor to detonation apart from being a heat source. There must be sufficient sulphide and thermal insulation to provide and retain enough heat for detonation to occur. A pathway to detonation is postulated whereby the heat travels upwards and results in evaporation of water in the explosive. When the temperature reaches approximately 200°C (400°F) the ammonium nitrate starts to decompose, decreasing the mass of the reacting species. The material in the top layers has reduced density and specific heat hence the temperature of the top region rapidly increases up to >1000°C (1800°F) and may initiate detonation. Field tests on loaded blast holes support this proposed mechanism. Case studies are presented whereby the research findings are used to provide an analysis of historical reactive ground events.

Jan 21, 2025

By Nikolaos Petropoulos, Ulf Nyberg, Ulf Stenman, Daniel Johansson, Håkan Schunnesson

The optimization of the explosive performance is of great importance since blasting is extensively used in civil projects and mining industry. An improved understanding of how the energy from the detonation of an explosive is transmitted to the surrounding rock mass is critical information for the proper selection of an explosive. Therefore, an extensive study was done on the influence of the blasthole diameter on the Velocity of Detonation (VoD) and the detonation front curvature.

Feb 1, 2020

By Elias Poulakidas, Marco Arellano

The impact of a higher copper price on the open pit metal mining sector has derived in a faster and safer way in which the mining operation of broken and mineralised material is carried out. In this regard, a good control of bench stability allows a lesser extra removal of material and so more safety to get the planned ore. The stability is ensured through an efficient drilling and blasting, applying the current technology and available know-how. An efficient use of energy through low-density explosives which are the most adequate for the existing solid rock releasing energy in a smoother way through a deterministic detonation sequence which is the application experience presented here. This application experience has two main technological factors; the adequate type of explosive for the kind of rock, in terms of velocity of propagation (Vp) together with the use of a determined detonation sequence and the appropriate designs, which allow to reduce the level of damage to the walls and to maintain a minor backbreaking through quantification with vibration modelling carried out at the near field. The reductions achieved were 30% lower in peak particle velocity.

Jan 1, 2008

By Alexander S. Escalante, Luis R. Ramirez, Nelson A. Arostegui

Research, analyze, discuss, design, and build an electric oven to perform one of the quality control tests the fanel or common fulminers to determine what temperatures they can detonate at. Give practical applications, conclusions, recommendations and bibliography.

Feb 1, 2020

By FM Murray

SAFEX International is a global organisation with more than 85 members, all of whom are manufacturers of explosives. On joining each member signs a declaration saying that they are willing to exchange information with regard to any accidents or near misses they may have in order to prevent the recurrence of the incident. SAFEX International was formed 50 years ago in Europe and has now built up a database of more than 700 accidents in the explosives business. Once every three years, an International Congress is held in which members address specific safety themes associated with the explosives industry, and also give details of "what went wrong?", "why?", and lessons learned. The next Congress will be held in Amsterdam between the 29th May and the 1st June 2002. This paper describes the operation of SAFEX International, which is dedicated to the international exchange of experience on industry connected accidents of the explosives business.

Jan 1, 2002

By Rick Lamkie

When investigating citizen complaints about blast vibration and airblast, it is important to be able to establish the spatial relationships between blasts, blasting seismographs monitoring the events, and complainant structures to assess any directional impacts. The Pennsylvania Department of Environmental Protection (DEP) routinely uses hand-held GPS receivers to document these relationships. The waypoint (structures and seismograph monitoring locations) and tracking (blasting and permit areas) features are used to map a site. These data are imported into the software for editing and conversion to GPS Exchange (.gpx) format.

Jan 1, 2008

By Kurt Oakes, John Williams

Placer Dome, US operates the Bald Mountain Mine. The Bald Mountain Mine is a surface operation located in remote northwestern White Pine County in east-central Nevada, approximately midway between Elko and Ely. The mine is in the Newark Valley along the southwestern flank of Bald Mountain a part of the Ruby Mountain range, at an approximate elevation of 7,500 ft (2,286 m). The geology at the Bald Mountain Mine is highly altered, both mineralogically, and structurally. Highwall stability and control have long been an issue at the operation, due largely to the varying geologic conditions. In some blasts as many as seven distinct geologic unconformities exist. These unconformities affect both final high wall integrities, as well as blast fragmentation characteristics. A 60 million ton (54.5 million tonnes) layback expansion of the existing “Top Pit” as well as development of a new satellite pit, “Sage Flats”, is being undertaken. Design final highwall pit slopes have been steepened from the traditional 47º to 55º in order to reduce overall ore-to-waste ratios, thereby improving economic viability for the expansion over the 4.5 year life of the project. With the increased usage of electronic detonators throughout the mining industry, mine operations staff, as well as representatives from the mines explosive supplier felt that an evaluation program incorporating electronic detonators would be warranted. The areas of focus for this evaluation would be resultant highwall pre-split integrities, peak particle velocity measurements (both near field and far field), frequency measurements, loader productivity, and visual interpretation of the results. The mine incorporates 25 ft (7.6 m) benches and uses separate trim blasts in conjunction with production blasts in order to reduce blast effects along final highwalls. Hole diameters in production blasts are 7? ” (200 mm). Typical production blast patterns are 18 ft x 18 ft (5.5 m x 5.5 m), drilled in a square pattern configuration. Shot sizes vary greatly, ranging from 200 holes to as many as 800. Bulk low percentage ANFO/emulsion blends are utilized as the redominant blasting agent. Non-electric dual delay detonators (25 ms/500 ms), with non-electric surface delays are the initiation system utilized in production blasts. Typical production blast design

Jan 1, 2004

By Alexandra Yuyali

The objective of this research work is to increase the drilling ratio represented in tons per drilled meter (ton/m) to reduce mining costs. One of the key characteristics of this research is the use of the ITH (in-the-hole) drilling rig with a water-powered hammer, also known as Wassara™. The patented Wassara™ in-the-hole hammer is powered by high-pressure water instead of air. To reach the objective, a new design of the blast pattern was implemented considering the following: Burden from 1.7 m (5.6 ft) to 2.8 m (9.2 ft) Spacing from 1.7 m (5.6 ft) to 2.7 m (8.9 ft) Drill diameter from 89 mm (3.5”) to 102 mm (4”) Drilling length from 15 m (49 ft) to 30 m (98 ft) Borehole deviation < 2% The result of this new design is the optimization of the drilling ratio (ton/m); having as a baseline 5.2 ton/m with traditional equipment and obtaining 13.7 ton/m with the ITH drilling, which generates annual savings of $2.43M.

Jan 21, 2025

By Donald Jonson

The Arlanda Link project is for the time being the most interesting project in Sweden, concerning rock and blasting technology. The total amount of rock excavated beneath Arlanda airport comprises 800 000 m³ divided in four parallel tunnels measuring a total length of 8,5 km, with a rock covering of only 5-15 m between the tunnel roof and existing terminal buildings.

Jan 1, 1997

Fracture Control Blasting is an alternative to pre- and post-splitting or smooth wall blasting. It was developed at the University of Maryland as an attempt to overcome some of the disadvantages that occur with normal blasting practices. There are two main factors that are unique to fracture control blasting. First, it utilizes a notched or grooved borehole to initiate fractures at desired locations and secondly, it employs a very carefully selected charge so as to provide control over borehole pressure. The maximum borehole pressure must be kept between very definite limits in order to obtain initiation of fractures at locations where they are desired and yet not obtain fractures where they are not desired. When coupled with stem induced fracturing, which was developed for oil and gas well stimulation, it has been found that the charge required for fracture control can be as little as 1/40th that required for normal smooth wall blasting. The paper describes the technique of fracture control blasting and gives results of some of the field testing conducted to date.

Jan 1, 1984