Search Documents

By V. F. Parry

[Subbituminous coal or lignite when stored in random piles or in ordinary bins in which the temperature fluctuates and air circulates quickly undergoes objectionable physical and chemical changes, which decrease the utilization value of the fuel and increase its tendency to ignite spontaneously. Slacking takes place, and the heating value decreases. These changes are accelerated by fluctuations of temperature and by circulation of air through the storage space. When such coals are exposed to the weather they lose moisture rapidly. If evaporation from the surface of a lump proceeds at a faster rate than that at which it is replaced by moisture from the interior, the rate of shrinkage at the surface is greater than that at the interior; consequently, stresses are generated at the surface which cause the coal to disintegrate. Likewise, when moisture is absorbed by the air-dried surface the outside layers expand at a faster rate than the interior, which results in further break-down. As these cycles are repeated the lump may disintegrate completely. Therefore, successful storage of low-rank coals depends on control of the factors that influence change of moisture.]

Jan 1, 1941

It is not uncommon to find large quantities of combustible materials in underground metal and non-metal mines. Support timber is the predominant combustible material. Spontaneous combustion, welding and cutting, shorted or overloaded electrical cables and careless smoking are common ignition sources. More recently, there is increased use of diesel mobile equipment that requires fuel storage and transfer areas. Diesel fuel spillage on hot engine manifolds and motors can result in rapid flame growth and heavy smoke accumulation in a matter of seconds. In-expensive, reliable fire detection and suppression systems are available to provide early warning of fire conditions and to isolate and extinguish fires that originate in fuel storage and transfer areas. This report presents an example of how technology developed and demonstrated under Bureau of Mines Contract H0242016, Mine Shaft Fire and Smoke Protection System, may be applied to protect underground diesel fuel storage and transfer areas. The area application described in this report is a representative example only; the fire protection described includes the concepts of ? Early warning and alarm ? Isolation ? Extinguishment ? Control

Jan 1, 2011

By V. F. Parry

Subbituminous coal or lignite when stored in random riles or in ordinary bins in which the temperature fluctuates and air circulates quickly undergoes objectionable physical and chemical changes, which decrease the utilization value of the fuel and increase its tendency to ignite spontaneously. Slacking takes place, and the heating value decreases. Those changes are accelerated by fluctuations of temperature and by circulation of air through the storage space. When such coals are exposed to the weather they lose moisture rapidly. If evaporation from the surface of a lump proceeds at a faster rate than that at which it is replaced by moisture from the interior, the rate of shrinkage at the surface is greater than that at the interior; consequently stresses are generated at the surface which cause the coal to disintegrate. Likewise, when moisture is absorbed by the air-dried surface the outside layers expand at a faster rate than the interior, which results in further break-down. As these cycles are repeated the lump may disintegrate completely. Therefore, successful storage of low-rank coals depends on control of the factors that influence change of moisture.

Jan 1, 1941

By A. T. Iannacchione

Underground limestone mines typically use the room-and-pillar method of mining in the generally flat-lying limestone formations. In some cases the dip may exceed 5° which can result in unique roof instability problems. Stability may be further exacerbated by the presence of horizontal tectonic stresses. Field studies and numerical model analyses are combined to assess the affect of the dip in various stress conditions. The results showed that where the horizontal tectonic stresses are sufficient to cause intact rock failure, increasing dip results in increased failure potential. The effect of the dip is greater when the maximum horizontal stress is parallel to the dip. Two case studies are presented and evaluated against the findings of stress analysis results. The study showed that the empirical rules of orienting headings parallel to the maximum stress are generally applicable to dipping excavations, except when mining in the up-dip direction. The importance of accurately determining the orientation of the maximum horizontal stress is emphasized because the window of favorable orientations relative to the stress is small.

By B. C. Peterson

Calumet Division, Calumet & Hecla, Inc., whose operations are in Houghton and Keweenaw Counties, Mich., is a highly integrated and complex organization. This division operates mines, a railroad, a concentrating mill, a reverberatory smelter, and the auxiliary generating plants and shops to service these operations. In addition, it operates a sands reclamation plant, leaching plants, a foundry, and a machine shop that serves varied industries with castings and parts for many applications. Calumet & Hecla, Inc. has produced over 60 percent of all the copper that has been produced in Michigan since discovery of the ore in 1864, and in 1959 the company ranked eight among the country's producers with a production of 17,407 tons. To keep abreast of modern accounting systems developed elsewhere in industry and to combat increasing costs due to higher labor and supply costs, as well as increased costs due to deeper mines and lower grade ore, the company has developed a modern machine cost accounting system. This not only provides the usual bookkeeping and cost accounting facilities but offers accurate cost data for engineering evaluation of the mining operation. This system is credited with being instrumental in permitting continued operation of these high-cost mines in a period of increasing costs with no corresponding increase in the price of metal.

Jan 1, 1962

By R. H. Dickson

This paper, which describes the milling practice of the Verde Central Mines, Inc., is one of a series on milling methods and costs being prepared by the United States Bureau of Mines. GENERAL DESCRIPTION The Verde Central concentrator is located in Walnut Gulch, about 1 mile west of Jerome, Ariz., and on the Jerome-Prescott highway. It is about 1,000 feet distant from the main shaft of the Verde Central mine and treats ore from this mine only. The mill is connected with the main shaft of the mine by a 24-inch gave railway, over which the ore is hauled in 5-cubic yard capacity, rocker, side-dump cars, by a 3-ton Brookville gasoline locomotive.

Jan 1, 1931

By H. B. Hill

The discovery of the Oklahoma City field and its rapid development into one of the major oil-producing districts is an outstanding epoch in the history of the petroleum industry not only of Oklahoma but also of the United States. The relatively great depth to which the wells were drilled and the large initial production of high-gravity oil are of special significance. The field has boon under proration almost from the time that its development began, and many new production problems have developed out of the changed conditions of operation. The discovery well was first tested in December 1928 at a depth of 6,402 feet, with an initial production of 4,847 barrels of 38,5.° A.P.I. gravity oil, and several months later was, completed at a depth of 6,624 feet, The large initial production, the high pressure, and the large gas volume in the different horizons of the discovery well suggested the potential possibilities of gas and oil, production in formations of Pennsylvanian and pre-Pennsylvanian age.

Jan 1, 1933

By John J. Sammarco

Illumination plays a critical role in an underground miner?s safety because miners depend most heavily on visual cues to recognize hazards. Mobile mining machinery, located in the miner?s peripheral field-of-view (±10° to about ±60° off-axis), may pose potential pinning and striking hazards. The main objective of this research was to determine if there were peripheral visual performance improvements for the detection of moving objects when using cool-white light-emitting diode (LED) cap lamps as compared to incandescent (INC) light bulbs commonly used in miner cap lamps. The cap lamp variable of interest is the spectral power distribution (SPD); the illuminances were normalized by a diffusion filter. The second objective was to determine if age is a factor for peripheral visual performance. This is important because the workforce is aging ? the average miner age is about 43 years old. Thirty subjects participated in the study; ten subjects each in the age groups of younger (18 to 25 years), middle (40 to 50 years), and older (50+ years). Visual performance was quantified by the subjects? speed and accuracy of response to detect the rotation of high-contrast (white) circular targets located 3.83 meters (m) away at -20°, 40°, and 50° off-axis. The speed of detection and the number of missed target rotations (accuracy) were measured. The prototype LED cap lamp results were best with a 11% to 15% improvement compared to the INC and LED cap lamps respectively. Age does appear to be a significant factor. For the middle and older age groups?, target movement detection time increased 75% and 60% and the number of missed targets increased 500% and 450% respectively in comparison to the youngest age group. The results also suggest that target location is a significant factor. The subjects? target movement detection time for the 40° and 50° target movements increased 16% and 69% respectively as compared to the -20° target.

Jan 1, 2008

By R. H. Schutz

TO ASSIST users in the selection of reliable and satisfactory respiratory protective devices, the Bureau of Mines bas established five schedules of minimum performance requirements for the approval of respirators. The current revisions of these schedules include 130 for self-contained breathing apparatus, 141F for gas masks, 19B and the amendments to 19B for supplied- air respirators, 21B for dust, fume, and .mist respirators, and 23B for chemical cartridge respirators. Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pitts- burgh, Pa., 15213. Approval tests on respirators are performed only at the request of the manufacturer of the respirator and at his expense. If the deice meets the approval requirements, a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an extension of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines he used where respiratory protection is needed. The Bureau of Mines, however, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators.

Jan 1, 1966

By R. H. Schutz

TO ASSIST users in the selection of reliable and satisfactory respiratory protective devices, the Bureau of Mines bas established five schedules of minimum performance requirements for the approval of respirators. The current revisions of these schedules3 include 13D for self-contained breathing apparatus, 141F for gas masks, 19B and the amendments to 19B for supplied- air respirators, 21B for dust, fume, and mist respirators, and 23B for chemical cartridge respirators. Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pittsburgh, Pa., 15213. Approval tests on respirators are performed only at the request of the manufacturer4 of the respirator and at his expense. If the device meets the approval requirements, a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an extension of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines he used where respiratory protection is needed. The Bureau of Mines, however, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators.

Jan 1, 1966

By David E. Kaslow

In sampling dust laden air by drawing the medium into an inlet, some larger particles fail to follow the air and a true sample is not obtained. Inertia prevents particles from accelerating with the air as well as from turning sharp bends; also the particles' weight causes them to fall relative to the air. An analytic solution to the sampling efficiency calculation by Levin gives particle paths and sampling efficiencies for various particle sizes when the inlet can be treated as a point sink. However, the flow field in the neighborhood of an aspirating tube is quite different from a point sink flow. Employing Levin's solution in the outer field, trajectories in actual flow fields have been calculated by computer to locate the critical trajectories separating the entering particles I paths from those paths where the particles hit the tube wall or escape. Sampling efficiencies are presented in terms of 3 variables--a dimensionless particle size coefficient, a dimensionless orifice size coefficient and the tube orientation--for the no-wind case. Over most of the range of sampling conditions, the Stokes drag law can be used and dependence on the variable--particle Reynolds number--can be ignored. A procedure for achieving maximum efficiency in design of a sampler is proposed. Whether these results apply when typical room-sized eddies constitute the ?calm air? environment is not known.

Jan 1, 1974

By Michael J. Beus

This Bureau of Mines report describes field investigations conducted in the Coeur d'Alene mining district of Idaho to obtain data on rock stress and physical properties. The resulting information has been utilized as input to detailed finite-element analyses to establish structural design criteria for deep-vein mine shafts. Measurement techniques include the Council for Scientific and Industrial Research biaxial and triaxial strain cells, the U.S. Geological Survey solid-inclusion probe, and the Colorado School of Mines dilatometer. Physical property testing was conducted in the laboratory on core obtained from each test site. Limited in situ physical property tests were also conducted. Reason-able success was obtained with the CSIR equipment, which was considered the most suitable for stress measurement in the study area. Test sites ranged in depth from 1,200 to 7,700 feet and are described in detail. The stress data were reduced by least-squares linear regression techniques to enable prediction of vertical and horizontal stresses to 7,500 feet. Ratios between the horizontal stresses as utilized for shaft design varied considerably, and a hydrostatic condition is the exception, based on Bureau measurements. Physical properties also varied widely, due to the complex geologic structure. Analyses of the data in terms of the tectonic history of the area show reasonable correlation. Data from previous rock mechanics investigations from the Coeur d'Alene district were also compiled and presented as part of this report to justify any generalizations regarding stress conditions and physical properties of the district as a whole.

Jan 1, 1980

By John R. McDonnell

The Valle Vidal Unit comprises 100,000 acres In Taos and Colfax: Counties, New Mexico. The unit was donated to the American public In 1982 by the Pennzoll Co. and is administered by the U.S. Department of Agriculture Forest Service as an addition to the Carson National Forest. During 1990-1991, the Bureau of Mines conducted a mineral Investigation of the unit as authorized by an Interagency Agreement (1987) Intended to assist the Forest Service to incorporate mineral resource data In forest plans. The Bureau reviewed literature and records concerning mineral resources and mining activity, and performed a field examination of mines, prospects, and mineral occurrences in and near the Valle Vidal Unit. The La Belle mining district encompasses most of the western part of the Valle Vidal Unit. The district was most active between 1893 and 1902, after the land grant was opened to prospecting and gold discoveries were reported. The discoveries were low grade, and eventually were abandoned. The Bureau's appraisal of the district determined that lode gold occurs primarily in fissure veins in volcanic rocks, and placer gold occurs In weakly cemented sedimentary rocks and alluvial sediments; but at a grade that is currently considered subeconomic. If the price of gold increases in the future, prospecting and exploration in the area may be renewed, but the activity would likely be limited due to "acquired land status" restrictions, which require mineral leasing and prohibit claim location in the Valle Vidal Unit.

Jan 1, 1992

By Peter C. Wood

This report describes research directed toward the preparation of chemical oxygen (02) sources which exhibited improved 02 storage and reaction characteristics when compared to potassium superoxide (KO2). The initial focus of the research was the preparation of calcium superoxide (Ca(02)2) by the disproportionation of calcium peroxide diperoxyhydrate. The Ca(02)2) was characterized by chemical, thermal, and x-ray analyses. Several methods for scaling up the Ca(02)2 synthesis process were studied. Next, the reactivity of Ca(02)2 toward humidified carbon dioxide (C02) was evaluated and was compare o that of K02 under flow-test conditions approximating those existing in portable breathing apparatus. The reactivities of mixtures of K02 and Ca(02)2 or lithium peroxide towards humidified CO2 were also studied. Finally, an analysis of two commercial, K02-based, self-contained self-rescuers was conducted to determine the potential weight and volume savings which would be possible if Ca(02)2 or a mixture of K02 and Ca(02)2 were used as a replacement for K02.

Jan 1, 1983

By R. H. Bedford

"The El Dorado copper mine is situated in the foothill copper-zinc belt of California, which traverses the western slope of the Sierra Nevada with unusual persistence from Butte County to Kern County, a distance of more than 300 miles. Although this area contains such important past producers as the Penn mine, Union, and others, a great part of the current production has been derived from smaller properties, which depend largely on premium metal prices for economical operation. The El Dorado mine is in the latter group, which constitutes an important source of metal in a national emergency.Exploration by the Bureau of Mines by means of eight diamond-drill holes Indicated narrow, intermittent lenses of copper ore along structures boo feet in length. The copper occurs in massive sulfides composed of chalcopyrite, pyrite, pyrrhotite, and minor quantities of bernite. The sulfides have evidently replaced tuffs, which are interbedded with the Mariposa slates and shales.H. A. Weiler and Hal T. Hall, owners of the El Dorado copper property, requested an examination by the Bureau during the latter part of 1914. In December of that year an engineer of the Bureau of Mines visited the mine and recommended the project work undertaken. The purpose was to aid the owners in bringing the property into production of copper and zinc, which at that time was critically essential to the war industries.Complete factual data obtained by the exploration are embodied in this report.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G, Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.Acknowledgment is made to A. O. Johnson, chief, Reno Division, Mining Branch, and Lowell B. Moon, chief, Mining Branch, for their aid and direction."

Jun 1, 1946

By R. O. Pynnonen

This publication is an analysis of reports to the Bureau of Mines of 44 fatal accidents that occurred during the operation of rubber-tired, front-end loaders in the mineral industry. The causes of the accidents, the nature of the work being performed, and recommendations for preventing similar accidents are included.

Jan 1, 1967

By H. S. Auvil

[The shrinkage of coke after formation is one of the variables that effects the net expansion of the change in both industrial and test ovens. Various test results5/ have been interpreted as indicating that cokes from certain coals shrink to a marked extent and that other cokes show very little shrinkage; but no comprehensive experimental study of the shrinkage of coke after its formation and of the factors influencing this shrinkage has come to the attention of the authors.]

Jan 1, 1940

By Thomas M. Barczak

This Bureau of Mines report describes research on developing technology to utilize shields as roof load monitors. Three-dimensional equations of static quilibrium are presented for a generic two-legged long-wall shield. The equations are presented in the most general form, assuming a force and moment vector at each reaction by rigid-body analysis of the shield mechanics. The resulting system of equations was found to be indeterminate to a very high degree. A three-dimensional solution to measurement of the resultant reaction on the canopy by the strata activity and shield response required the elimination of several forces or moments that were thought to be nonparticipating or to not significantly affect overall shield mechanics. Required measurements for solution of the equilibrium equations were leg, canopy capsule, and lemniscate link forces. Two-dimensional analysis, which considered forces acting only in the roof-to-floor and face-to-waste plane, was also provided by reduction of the three-dimensional equations~

Jan 1, 1987

By John R. McWilliams

This report is one of a series published by the Bureau of Mines describing methods and practices at various mines throughout the United States. A previous program, conducted from 1928 to 1939, was well received by the mining industry and technical institutions and provided much source material for engineering textbooks and technical handbooks. The stringent wartime demands on the mining industry, the rapidly changing postwar economic situation, and greatly accelerated technologic growth have combined to render many of the previous data obsolete. The objective of the present program is to assemble reliable technical information on mining methods and practices throughout the country and present it for the use of the mining industry, technical schools, textbook authors, and other interested persons. This report deals with the design and development of the Berkeley open- pit mine at Butte, Mont., owned and operated by The Anaconda Company. The Berkeley pit is but one facet of a well-organized and integrated copper-mining operation involving the entire Butte district. Vein-type mining, important for 75 years, is still in progress at depths from 600 feet to nearly 1 mile; on intermediate levels, low-grade ore left untouched by earlier vein-type mines is being extracted by block caving entire ore zones,3/ and secondarily enriched but lower grade near-surface portions of the same ore zones are being mined by open-pit operations (fig. 1). The Berkeley pit itself is named for the Berkeley mine, one of the old mines that extracted copper ore from high-grade veins in the area that now will be mined by open-pit methods.

Jan 1, 1959

By R. J. Kuczynski

The U.S. Bureau of Mines operated a 2,000-g (4.4-lb) batch process development unit for recovering platinum-group metals (PGM) from automobile catalysts. Virgin monolith, used pellet, and used monolith catalyst samples were tested. Leaching twice with 1-pct sodium cyanide (NaCN) solution at 1600 C for 1 h dissolved more than 95 pct of the PGM from virgin catalysts and more than 90 pct from used pellet catalysts. More than 85 pct of the PGM was dissolved from used monolith catalysts when a third autoclave step was added. Solid PGM concentrates containing more than 99.8 pct of the dissolved PGM and analyzing greater than 70 pct PGM were recovered by heating the pregnant leach solutions from virgin catalysts to 2500 C and used catalyst to 2750 C for 1 h. The solution after heating contained less than 0.2 ppm. total cyanide. The virgin residues passed the EPA Extraction Procedure Toxicity Test (EP Tox Test), the EPA Toxicity Characteristic Leaching Procedure (TCLP), and the California Waste Extraction Test (WET) for all elements except Ba. Adding sodium sulfate (Na2S04) to the virgin leach residues reduced the amount of Ba dissolved to an acceptable level. The used leach residues passed the EP Tox Test for all elements but failed the WET and TCLP for Pb.

Jan 1, 2010