Search Documents

By Louis Schaffer

The objectives of the research were to determine whether a model health and safety program could be defined in terms which would enable its application to mines of all types, and, if such a model program could be defined, to determine through evaluations in two mining companies whether it would achieve measurable improvements. Volume 1 describes the model, how it was applied in the field and how it was evaluated. This, Volume 2, describes the literature and field research that preceded the model definition.

Jan 1, 1983

By Walter W. Hyde

This paper describing the mining and preparation of sand and gravel for a number of special markets by the East Texas Gravel Co., Dallas, Tex., is one of a series being prepared on the subject by the United States Bureau of Mines. These articles are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole, but on the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1931

By E. K. Stanek

The field tests involved ten coal mines in which transients were initiated on the dc system from which the parameters of the dc mine electrical power system could be determined. The data processing involved the use of a Fourier Analyzer to filter noise and fit an exponential curve to the field waveforms. From this data analysis it was possible to find the dc system resistance, inductance and time constant. The survey of nationally recognized laboratories was conducted to establish that the recommended test criteria were practical. The development of test criteria for dc fuses used in mines was based on the measurement of parameters in the field, the survey of testing laboratories, literature searches, laboratory test, etc. A computer program was written to analytically predict the parameters measured in the field. This approach has limitations but reasonable agreement with field results was obtained. A brief laboratory testing program was carried out to verify the practicality of the recommended criteria and establish the accuracy of the conclusions concerning dc fuse performance.

Jan 1, 1984

By P. T. Brooks

A process for extracting 69 percent of the vanadium from weathered Nevada dolomitic shale containing about 1 percent V205 was developed on a laboratory scale by the Bureau of Mines. The process essentially is comprised of salt roasting, leaching with dilute sulfuric acid, solvent extraction, and precipitation of vanadium as ammonium metavanadate. Carbonaceous unweathered shale was less amenable to treatment. A preliminary cost estimate for mining and processing 1,500 tons per day of weathered shale indicated a production cost of about 1 dollar per lb of V205. Considering recent sales at nearly $1. 75 per lb of contained V205, larger scale testing to obtain more definitive process design and evaluation data may be warranted.

Jan 1, 1974

By C. E. Armantrout, H. Kato, M. I. Copeland

The data collected during this investigation indicate that the chromiumgadolinium system has extensive liquid immiscibility and one eutectic point . Liquid immiscibility occurred at temperatures above the monotectic isotherm , 1,830 ° C , which extended from less than 0.25 to about 85 weight - percent gadolinium . The eutectic was at 96 percent gadolinium and 1,170 ° C. Gadolinium and chromium were the only phases in this system . There was a solid solubility of less than 0.25 percent gadolinium in chromium at 1,730 ° C and less than 0.10 percent chromium in gadolinium at 1,160 ° C. The alloys were prepared by nonconsumable - electrode arc - melting , and the alloy system was investigated by heat treatment , metallography , thermal analysis , and X- ray diffraction . All the melting , heat treatments , and thermal analyses were conducted in a vacuum or in helium because of the reactivity of chromium and gadolinium with the components present in the atmosphere at elevated temperatures .

Jan 1, 1964

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By John P. Hansen

Batches of red or brown iron ore concentrates, weighing 100 or 200 grams, were reduced with gaseous reductants in a laboratory-sized fluidized-bed reactor. Using a loss of weight technique, the rates of reduction were measured and the effects of temperature, gas consumption, and gas flow rates were determined. Below about 725° C the rate of reduction was controlled by the chemical reaction at the reduction interface having an activation energy of about 10 kcal/g mole. Above about 725° C the rate of reduction appeared to be controlled by the flow of the gaseous reductant and therefore to be directly proportional to the flow rate. Above 725° C, hydrogen reduced the iron ore much faster than carbon monoxide. In gas mixtures, carbon monoxide or nitrogen reduced the hydrogen partial pressure and lowered the reaction rate proportionally. When present in large concentrations, carbon monoxide had a serious inhibiting effect on the reduction rate, probably owing to carburization and sintering of the reduced iron.

Jan 1, 1970

By Donald B. Lindsay

A new concept was proposed for a personal warning device for use by miners who may be exposed to health hazards from inhalation of alpha-emitting radionuclides, especially radon-222 and its short-lived daughters. Two successive prototype models of the proposed instrument were designed, fabricated and tested. The Personal Alpha Alarm, in its final form, weighs less than 90 g (3 ounces), and can easily he mounted on a miner's safety cap. It is powered r, by electricity drawn from the cap-lamp battery, and consumes less than 100 n A at 4VDC. It is entirely passive and has no moving parts. Alpha-radiation originating in the air around it is detected by a 5 cm2-area semiconductor-type sensor that was developed especially for this purpose. The presence of alpharadiation in the air is communicated to the wearer by means of a small flashing light-a light-emitting diode-clipped to the brim of the safety cap. When the intensity of alpha-radiation exceeds a predetermined threshold, the flashing mode changes to a continuous illumination, thus providing an alarm signal to the wearer. Because the detector senses all alpha-emitters in the air, including 222Rn, it is not able to measure Working Levels accurately. For its intended purpose, however, which is to give a timely warning of excessive levels (several times the normal control level) of radon and/or radon daughters in an individual's air environment, the Personal Alpha Alarm is expected to be a useful instrument.

Jan 1, 1978

By F. A. Jones

Increased mechanization .of coal mines has emphasized the need for study of actual power requirements of the various machines employed in the production of coal and losses in the distribution of power to these machines. These studies are being made in order that hazards, excessive use of power, and high maintenance cost of equipment resulting from these losses may be analyzed and eliminated where possible. Research on the use of electric power in-coal mines was suggested by the Advisory Committee of the Bureau of Mines in 1937, and it was decided to begin with a study of individual machines of various types under operating conditions in modern coal mines. The transmission of power, particularly line losses and inadequate return circuits, should be a part of the investigation. This report presents some of the data of an initial study in commercial mines. ACKNOWLEDGMENTS The superintendents, engineers, and other officials of the two mines studied cooperated fully and aided in setting up and transporting the test equipment, giving such information as was requested.

Jan 1, 1942

By C. H. Riggs

This report presents pertinent data on all active water-flooding projects in Washington County, Okla., and describes in detail the operation and production history of five representative floods. The flooding of partly depleted oil-bearing sands to produce petroleum that would not be recovered by other methods is becoming increasingly important to the oil industry. In 1942, two water-flooding projects in Washington County produced 35 barrels of oil daily from 90 developed acres. In March 1951, 4,000 barrels of oil was being produced daily by the injection of 58,000 barrels of water on 19 active projects covering 1,645 acres. Several projects are being extended, and new operations are being initiated. Figure 1 shows the location of the active water-flooding projects in Washington County. The yearly oil production from Washington County increased from 1,076,000 barrels in 1948 to 1,720,000 barrels in 1950, owing principally to the effects of water flooding. To March 1951, permits to flood more than 8,000 acres in Washington County had been granted by the Oklahoma Corporation Commission.

Jan 1, 1951

By Charles E. Whieldon

The importance of producing more oil from known petroleum reserves has placed increased emphasis on the application of secondary-recovery methods. Recently published reports3 4/ describe the results of waterflooding in Roane and Pleasants Counties, W. Va. (see fig. 1.) This report describes the Barron Kidd Oil Co.?s Santee waterflood project, Maxton sand, Burton field, Church district, Wetzel County, W. Va. (See fig. 2.) The Federal Bureau of Mines hopes that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases.

Jan 1, 1961

By W. P. Yant, G. W. Jones

"Introduction.During the past two years the Bureau of Mines has conducted a study of natural-gas heaters*** to determine (1) what types of heaters literate carbon monoxide; (2) why carton monocide is liberated; and (3) how, by change of design or construction, the liberation of this gas can be largely eliminated, In addition to the above study the bureau has investigated cases in the Pittsburgh dis¬trict where fatalities have resulted from carbon monoxide given off by natural-gas heaters.Since these fatalities were first brought to the attention of this bureau through the press, it is likely that some cases were missed and thus not listed. On the other hand, some cases reported as being due to carbon monoxide poisoning, on investigation were found to be due to causes other than carbon monoride.The cases listed herein were shown in all probability to be due to carbon monoxide. Those in which there is any doubt have been omitted; so have those in which there was part asphyxiation, where the victims later recovered."

Feb 1, 1924

By S. M. Shelton, W. A. Calhoun, M. M. Fine, T. L. Johnston

"FOREWORDFerrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced; although it is well known that there are large deposits of low-grade are in the United States, the production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stockpiled ore depleted through inability to procure adequate supplies from foreign sources. Consequently, a program of laboratory,and pilot-plant investigation designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines.This paper is one of a new series that include reports of results obtained in the various investigations conducted under the manganese program. The scope of the program and the organization that was set up to direct and supervise the were discussed in the foreword of the first paper of this series, Report of Investigations 3606 Manganese Investigations. 1. Concentration of Manganese Ores,from the Drum Mountain District, Utah, by S. R. J. D. Vincent, and C. R. Schack. Other reports will be published as the work progresses."

Mar 1, 1942

By R. L. Marek

The number of persons fatally injured in the California petroleum industry in 1931 was 30, a decrease of 20 fatalities or 40 per cent from the number killed in 1930. As a result of the decrease in the number of fatalities for 1931, the fatality curve of tie California petroleum industry reached its lowest point in nine years. Although reductions in personnel--which permitted the retention of a select and experienced class of workmen, decreased active field-development work, and curtailed production--undoubtedly have had a marked effect on reducing the number of fatalities in 1931, the decrease also has resulted from continued accident-prevention efforts. Statistics show that a direct relationship exists between development activity and the number of men accidentally killed in the drilling and producing division of the California petroleum industry. For example, when the average number of drilling wells in 1930 was 29 per cent less than in 1929, the number of men accidentally killed at drilling wells dropped 48 per cent; and when the average number of drilling wells in 1931 decreased 52 per cent from 1930, the number of fatalities at drilling wells decreased 58 per cent. The relationship between field-development work and fatality frequency is significant because each year at least 50 per cent of all the fatalities in the California petroleum industry occur in the drilling and producing division. This relationship should serve to guide the accident-prevention efforts of the industry, especially in the drilling and producing division, toward checking an increase in fatal accidents when development activity again takes an upward trend.

Jan 1, 1932

By Jr. Fish

As a part of a study of iron are resources in the Appalachians, 9 diamond drill holes aggregating 1,580.7 feet were drilled in a portion of the Butt Mountain area of northeastern Giles County, Virginia. Three hematitic sand-stone beds were intersected in the Clinton formation but only one was consistent in thickness and grade in all 9 drill holes. This bed averages 18.9 percent iron over an average thickness of 24 feet. The drill cores were logged and chemical analyses were made on 161 individual samples and 22 composite samples. Beneficiation studies were made of three composite hematitic sandstone samples each representing a separate bed containing 14.6, 19.8 and 20.0 per-cent iron. Major mineral constituents of the samples were hematite, quartz, and sericite.

Jan 1, 1967

By Victor E. Kral

"SUMMARYA preliminary examination of the Buena Vista iron deposit was made in June 1942 by Paul E. Pesonen, mining engineer of the Bureau of Mines. Subsequent examinations were made by D. W. Butner, of the Bureau, in March 1943, and by the author in July 1944, who recommended exploration by diamond drilling, trenching, and sampling. Work on the project was done during the period March 28 to May 26, 1945.Property holdings, comprising 16 claims known as the Buena Vista group, are situated in sec. 4, T. 24 N., R. 34 E., Mount Diablo base and meridian, north Churchill County, about 37 miles east of Lovelock, Nev.Three diamond-drill holes totaling 575 feet were drilled; 45 small pits and ten trenches, totaling 435 linear feet, were excavated, and 84 channel samples totaling 862 feet were obtained under supervision of the Bureau.Purpose of the project was to determine the possible downward extension of the mineralized sections exposed in the outcrops and to determine grade of the ore.Bureau work was confined to one claim only - the Iron Mountain."

Jun 1, 1947

By H. H. Schrenk

The safe use of a refrigerant or any substance depends on knowledge of its pertinent properties and conditions of use; therefore some of the properties of refrigerants that are related to life, fire, and explosion hazards are discussed herein. These data serve as a basis for suggested control measures in the use· of refrigerants. The properties of refrigerants may be broadly classified into three main groups: (1) Those important for refrigeration, (2) those significant from the standpoint of confining the refrigerant, and (3) those that become important if the refrigerant escapes from the :machine or container. The first group of properties, such as latent heat of vaporization, specific heat of vapor, specific heat of liquid, etc., is not considered to be directly related to safety and is not discussed here. The second group, those properties important in confining the refrigerants, has particular significance because· it relates to "built-in" safety. This group is emphasized because it is believed the soundest procedure in designing equipment is to give due consideration .to both the health and safety hazards likely to be associated with the equipment. Furthermore, the toxicity, fire, and explosion hazards are controlled as long as the refrigerant is confined. Some properties of this group are (1) stability, (2) corrosiveness, (3) boiling point, (4) pressure developed in the system, (5) warning odor or irritation, and (6) ease of detection. The third group includes such properties as toxicity (of compound and decomposition products), irritating action, and explosibility.

Feb 1, 1942

By I. Liebman

A Bureau of Mines study is in progress to determine the effectiveness of passive water barriers in suppressing coal-dust explosions. A 2.9-ft3-capacity water-filled plastic tub was found effective in suppressing dust explosions propagating at speeds of 250 to over 1,000 ft/sec. Work directed at determining the limitations of water barriers showed that the passive water barrier technique is also feasible for the suppression of weak dust explosions propagating at speeds of 100 to 250 ft/sec. For relatively slow accelerating flames, dynamic wind forces appear to be the important quantity governing fragmentation of the plastic tub and subsequent water release and dispersion, whereas dynamic impulse appears to be the significant quantity for rapidly accelerating flames. The acoustic approximation (relation between static pressure and flame or wind speed) is shown to be valid in a long single mine entry. This relationship appears to be useful in predicting the regions within a long single entry where passive water barriers are effective in quenching a dust explosion.

Jan 1, 1974

By Homer J. Ballinger

The Alma, Degraff and other mines controlled by the Mon-Ark Mining Co. comprise one of the more important groups of zinc-lead mines in Christian County, Mo. The mines were first operated in .1857 and produced more than 5 million pounds of lead from rich, shallow ore deposits. Recent exploration and development led to the discovery of zinc sulfide ore at a depth of 165 to 214 feet in the northern part of the Alma mine. After examination of these mines in September 1942 by Bureau of Mines engineers, investigation of the extension -of the Alma mine and of the depth of mineralization at the other mines appeared justified in order to encourage the production of additional zinc and lead for war purposes. Twenty-nine churn-drill holes totaling 6.463 feet of bore were completed by the. Bureau from September 1943 to January 1944.

Jan 1, 1948

By Julius Roth

Flyrock is the source of most of the injuries and property damage in a majority of blasting accidents in surface mines. A quantitative correlation between shot conditions and maximum flyrock range can be used to define a "blasting area" in which no personnel or equipment should be present during a shot. The approach used was to develop a model that correlates shot conditions and initial flyrock velocities and permits computation of flyrock range from ballistic trajectories. The Gurney formula for velocity of explosively-propelled plates or fragments was adapted to explosively-propelled flyrock from vertical rock faces or from bench tops. The modified Gurney formula was then "calibrated" with measured flyrock velocities from mining and explosives literature. Charts were then developed for possible field use which give maximum flyrock range as function of shot conditions. The model indicates that for flyrock from vertical faces, borehole diameter, minimum burden and height of explosive column define maximum flyrock range for a given explosive, shot in a given rock. For flyrock originating from bench tops, flyrock range appears to be controlled by the distance of the top of the explosive column to the borehole collar, by total explosive load per borehole and, to a lesser extent, by borehole diameter.

Jan 1, 1979