Search Documents

By Bruce I. Thomas

Reconnaissance studies of beach sands along the eastern part of the Gulf of Alaska were conducted by the Bureau of Mines to determine if any of these coastal areas warranted investigations as possible sources of valuable minerals. Because of difficult access and limited transportation facilities only a minimum of sampling, surveying, and camping equipment is utilized to obtain spot samples from key areas as well as information indicating the location, size, and character of the deposits. Such data were obtained from beaches located along approximately 247 miles of the Gulf of Alaska coastline during parts of the 1957 and 1958 field seasons. A total of 201 3-inch-diameter auger holes, spaced roughly at 1 mile intervals, were bored by hand methods to depths ranging from 3 feet to 27 feet; also 33 shovel samples were collected from selected localities. Samples were reduced to a rough concentrate in the field by panning; the rough concentrates were shipped to the Bureau of Mines laboratory at Juneau for further concentration and for petrographic and chemical analyses. Particular attention was given to the heavy-mineral content of the concentrates, although the types and relative amounts of rock-forming minerals were also determined. The reconnaissance indicated that, generally, the valuable mineral content of the beach deposits was too low to be of further interest except in the vicinity of Yakutat and Lituya Bays where erratic but possibly significant concentrations of magnetite and/or ilmenite were found. At Yakutat, about 20 miles of beachline extending southeasterly from Ocean Cape, yielded samplas containing from 1 pound to over 300 pounds of iron and from a trace to over 100 pounds of titanium dioxide (TiO2) per cubic yard of beach material. However, the higher grade samples represented local concentrations of minor importance. The general tenor of the Yakutat beach, as indicated by the airthmetical average of 27 auger-hole samples, is about 35 pounds of iron and 20.5 pounds of titanium dioxide per cubic yard of beach material. Ilmenite is the predominant heavy mineral of the beach deposits in the vicinity of Lituya Bay, but it was found in concentrations only in limited areas near the

Jan 1, 1962

By E. J. Schneider

In view of the growing commercial interest In the higher boiling fractions of low-temperature tar, a study of the literature has been undertaken to obtain as many data as possible regarding the properties of possible pure constituents. The following substances have been studied: THREE-ORTHO-XYLENOL (1, 2-DIMETHYL-3-HYDROXYBENZENE) Detection By the isolation of the silver salt of 1, 2-dimethyl-3-phenoxyacetic acid.

Jan 1, 1930

By B. J. Moore

This publication contains analyses and related source data for 310 natural gas samples from wells and pipelines in 16 States. All of the samples were obtained and analyzed during calendar year 1978 as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis appara¬tus, which are described in Bureau of Mines Bulletins 4862/ and 576.3/ The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the public in general. Twenty previous publications have presented the results of 11,573 gas analyses made prior to 197R. The first three, Bulletins 486,4/ 576,5/ and 617,6/ contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other 17

Jan 1, 1979

By Virgil A. Marple

The objective of this contract was to investigate time-integrated and real-time methods for determining the diesel exhaust particulate concentration in underground mines, in particular, coal mines. The microorifice uniform deposit impactor (MOUDI) is recommended for obtaining the time-integrated measurement of the size distribution. The mass concentration of diesel exhaust particles can be obtained from the particle size distribution of mine aerosols. On a mass basis, diesel exhaust particles are primarily in the submicrometer size range while coal dust particles are larger. Size distribution measurements made in the laboratory and in three underground coal mines exhibited two distinct modes with the diesel exhaust particles in the smaller particle mode and the coal particles in the larger particle mode. The point of separation between the two modes occurred in the 0.7 to 1.0 pm size range. The separation was found to be independent of mass fraction of the diesel exhaust particles, particle concentration and sampling site. Methods recommended for further consideration as real-time monitors of diesel exhaust aerosols in mines are photometers and filter pressure drop techniques. A preclassifier would be required in both cases to separate the larger dust particles from the sample. The Metrex Mineral/Diesel Photometer should also be investigated further once the electronics problems are eliminated.

Jan 1, 1986

By D. J. Parker

Owing to its flexibility, convenience, economy, ands availability, electric power is peculiarly adapted to the needs of the coal -mining industry. Because of such obvious advantages, the application of electricity has in recent years become more and more extensive and is now a most important factor in the Nation's coal prediction. With the introduction of this type of power into coal mines certain new, specific, and well-recognized hazards resulted. The question arises, therefore: Has the industry met these hazards squarely and. effectively? With respect to some individual companies, the answer happily is in the affirmative; with respect to the industry as a whole, there is much room for improvement.

Jan 1, 1933

By J. A. Herdlick

"INTRODUCTION The BeVan quartz crystal prospect in the Indian Creek mining district of Lemhi County, west-central Idaho, was examined by an engineer of the Bureau of Mines 3/ on July 9, 1943. As quartz crystals possessing peizoelectric properties were on the critical list of strategic war minerals, further exploration of the deposit was recommended. The Bureau of Mines exploration began in December 1943 and continued through January 1944. Additional trenching was completed during May and June 1944. This report presents the data obtained by this exploration.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual exploratoiy work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyses samples and makes beneficiation tests.The quartz crystals found during the exploration were examined and classified at the Bureau of Mines College Park, Md., laboratory and checked at the National Bureau of Standards, Washington, D. C.Fred BeVan, of North Fork, Idaho, and Edward F. Cenis, of the Montana Coal & Iron Company, Spoane, Wash., provided much information on the history and past production of the property."

Mar 1, 1948

Large quantities of combustible materials are often found in underground metal and nonmetal mines, with support timber most often the predominant combustible material. Oils, lubricants, paper, cartons, and rags are additional combustible materials and are commonly found in maintenance shop areas. Welding and cuting, shorted or overloaded electrical cables, spontaneous combustion, and careless smoking are some of the common fire ignition sources. Inexpensive, reliable fire detection and suppression systems are available to provide early warning of such fires and to isolate and extinguish fires that originate in underground maintenance shop areas. Technology developed and demonstrated under Bureau of Mines Contract H024216, Mine Shaft Fire and Smoke Protection System, may be applied to protect underground maintenance shop areas. The mine area described in this report is a representative ex-ample only; the fire protection system described considers costs, benefits, equipment performance and includes the concepts of: ? Early warning and alarm ? Isolation ? Extinguishment ? Control. Each fire protection system application requires analysis of numerous variables including total mine profile (depth, personnel, escape routes, hazards, etc.).

Jan 1, 2011

By M. Kanda

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in and above an operating coal mine, McElroy Mine, located near Moundsville, West Virginia. The electromagnetic environment created by 300 volt dc and 480 volt ac machinery was measured. In one technique noise was measured over the entire electromagnetic spectrum of interest for brief time periods. The noise was recorded using broadband analog magnetic tape. The noise data was later transformed to give spectral plots. In the other technique, noise amplitudes were recorded at several discrete frequencies for a sufficient length of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 1, 1974

By F. D. DeVaney

[In the course of the investigation by the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy at the Mississippi Valley experiment Station at Rolla, Mo., on the beneficiation of the low-grade manganese ores of the country, some samples from the Cuyuna District, Minn., have been examined. The work was done under the direction of W. H. Coghill, supervising engineer of the Mississippi Valley Experiment Station. Josoph and Kinney5 in venting about the relative importance of Minnesota deposits of low-grade ore compared to the total reserves say:]

Jan 1, 1930

By R. L. Grant

The Bureau of Mines developed two new gap-sensitivity methods for explosives, and especially permissible explosives, to overcome certain disadvantages of the present routine half-cartridge method. The revised methods are based on the statistical up-and-down method and give more useful measurements of the 50-percent' gap values than the nonstatistical routine method. The new methods use full cartridges and incorporate certain physical improvements such as the use of cardboard tubes for containing the explosives and coal dust gaps to simulate actual mining conditions. A total of 60 samples of permissible explosives were evaluated simultaneously with the 2 improved methods and with the half-cartridge method

Jan 1, 1967

By S. B. Levin

The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States and Alaska since 1939. During the fall of 1942, the Bureau of Mines put down nine diamond-drill holes at the Cape Rosier zinc-copper-lead mine in Hancock County, Maine, that aggregated 2,883 feet of bore. These holes supplemented 13 holes, aggregating. 5,501 feet, put down on the property about 2 years earlier by the St. Joseph Lead Co. Veins of mixed sulfides were intersected in 15 of the holes drilled. Beneficiation tests were made on samples of ore obtained from old dumps. Zinc-copper-lead sulfides occur at the Cape Rosier mine as lenses in a zone of altered agglomerate beneath and between a series of diorite sills. The mineralized zone strikes F. 17° E. and dips southeast. Between July 1881 and September 1883 the mine produced about 10,000 tons of ore reported to have contained 20 percent zinc, 2.8 percent copper, and some lead. The crude ore was hand-sorted, and some. 3,000 tons were reported shipped.

Jan 1, 1948

By Michael S. Miller

In 1984, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied the 34,050-acre Cow Creek Wilderness Study Area (WSA) in order to evaluate its mineral resources. The WSA, located about 60 miles southeast of Havre, MT, contains sandstones, shales, clays, and coal of Cretaceous age. The Cretaceous rocks have been intruded by ultramafic diatremes. Quaternary glacial, stream, and landslide deposits overlie the older rocks. Claims are staked at five of seven sites favorable for diamonds within the WSA and at additional sites nearby. Although the ultramafic diatremes within and near the WSA contain minerals that are indicators for diamonds, no positive evidence of diamonds was found during this study. An abandoned coal mine, the Shellenberger, is inside the southwest boundary of the WSA. Possible petroleum and natural gas at depth are currently of interest; land within the WSA is leased or under lease application for oil and gas. The WSA contains subeconomic clays, zeolites, gold, silver, platinum group metals, and coal.

Jan 1, 1986

By R. P. Jewett

The object of this investigation was to correlate the crushing strength of green pellets prepared from magnetite, specular and earthy hematite with the particle size of these respective raw materials. In this study no attempt was made to correlate the strength of fired pellets and particle size. The effect of particle size upon a number of fine ores and concentrates was studied. Much of the low-grade ore reserves in the Lake Superior Region must be finely ground before concentration and then agglomerated for iron and steelmaking processes. Fine natural ores also must be agglomerated. Pellets constitute an important type of agglomerate. Considerable handling occurs during screening to remove undersize and oversize pellets, and in transfering green unfired pellets from the balling machines to the heat-hardening equipment. As a result the strength of the green pellets is a factor of great importance.

Jan 1, 1961

By Lawrence K. Barker

Crude shale oil produced by underground retorting of Green River Formation oil shale was hydrogasified over a cobalt-molybdate-on-alumina catalyst at operating temperatures ranging from 800° to 1,300° F, pressures of 500, 1,000, and 1,500 psig, and a liquid hourly space velocity of 1.02 volumes of oil per volume of catalyst per hour (Vo/Vc/hr). At a temperature of 1,300° F and pressure of 1,500 psig, 94 weight-percent of the liquid feed was converted to gas containing 72 volume-percent methane. With two reactors in series at a temperature of 1,170° F in reactor 1 and 1,260° F in reactor 2 and a pressure of 1,500 psig, 97 weight-percent of the liquid feed was converted to gas with a methane content of 75 volume-percent. Liquefied petroleum gas (LPG) was hydrogasified at operating temperatures ranging from 500° to 1,400° F at a pressure of 500 psig over a cobalt-molybdate-on-alumina catalyst. Similar experiments were made with an empty tubular reactor. The data indicate that gasification reactions in the presence of a cobalt-molybdate catalyst change from predominantly a catalytic (carbonium ion) reaction to predominantly a thermal (free radical) reaction at temperatures greater than 1,100° F. The data also indicate that a reaction temperature of 1,350° F is necessary at the space velocities used in this investigation to make a synthetic natural gas (methane content of 90 volume-percent) from in situ crude shale oil.

Jan 1, 1975

By Albert Ketler

[Early Bureau of Mines research had produced a fluorescent mine illumination system which was approved by MESA under Schedule 29A for use as portable equipment Intense industry preference for machine-mounted hardware required a MESA 2G approved system. The modifications required to upgrade the portable system arc herein described.]

Jan 1, 1976

By C. C. Stevenson, Thomas Varley

"The art of treating ores by the chloride volatilization process is still in the experimental stage. The process has not been sufficiently developed along chemical and metallurgical lines to state definitely just what place it will occupy in the metallurgical industry. The theory upon which the process operates has received the attention of prominent metallurgists for the past twenty years, and research and experimental work has been conducted by many investigators.Much of the experimental work done has never been published, and it seems that the accumulation of such results if made known would be an important aid to the further development of the process. The object of this paper is, therefore, to bring salient features of the process to the attention of the metallurgical industry, both for the purpose of furnishing information, and receiving from interested parties any comments which the reading of this article may suggest. A bulletin covering the work done at the Intermountain experiment station of the U. S. Bureau of Mines, situated at Salt Lake City, Utah, is in course of preparation.The chloridizing roast is usually accompanied by appreciable losses due, to the volatilization of the metals as chlorides during the roast, these losses often running as high as 30 per cent, depending upon the temperature, the character of the ores and the associated gangue material. It was not until 1891 that Croasdale, (Croasdale, Stuart, Engineering and Mining Journal, Aug. 29 1903) by observing this and stack deposits from the chloridizing roast, recognized the possibility of making volatilization a major instead of a minor feature of the roast. He then made tests on a large number of tires from different, localities, the result of which showed the, general application of the process. The main difficulty, as stated, by Croasdale, was the lack of a suitable means for recovering the fume from the furnace gasesIn 1913, Cottrell (See Mining and Scientific Press, March 29, 1913; alsoTrans. American Institute of Mining Engineering, September 1918. (Additional informa-tion is available from the owners, The Research Corporation of New lark, and Western Precipitation Co., .Los Angeles, Calif.), announced his invention of the electrostatic precipitator, which solved the problem of separating the solids from the furnace gases."

May 1, 1921

By Robert S. Sanford

This paper deals with truck haulage methods and costs at one of the many open-cut mines that are replacing rail haulage with heavy-duty trucks. At this mine, ore is trucked to a crushing plant, centrally located within one of the open-cuts. The requirements for efficient low-cost truck haulage are: Good trucks designed for heavy loads, adequate truck maintenance, smooth roads, and well-trained truck drivers The weighted average cost of hauling a long ton of ore to the crusher and the waste to the dump was reduced from $0.1993 in 1948 to $0.1114 during the last half of 1949, his corresponds to a cost per ton mile of $0.0864.

Jan 1, 1952

By Fun-Den Wang

This report presents theoretical studies and experimental work dealing with the detection of dangerous roof and pillar conditions in underground mines through measure¬ment of temperature differences on the surface of the mine opening. The theoretical work is directed at modeling the circumstances where a loose slab of rock might be detected. The experimental work provides input data for the theoretical models. At the beginning of the project, little was known by the authors of the conditions that would permit detection of a loose slab of rock or coal by measuring the surface temperature differences. The U.S. Bureau of Mines had found that there were detectable surface temperature differences on the roofs and pillars of mines. The Bureau contracted with Colorado School of Mines to measure temperature profiles around mine openings in an effort to learn if the temperature differences they had detected were directly related to loose pieces of roof and pillar rock. The Bureau was principally interested in learning if loose rock could be found in coal mines by measurement of surface temperature differences with an infrared thermometer.

Jan 1, 1972

By S. Ralph Austin

Emanation coefficients of 950 samples of domestic uranium ore were successfully and rapidly determined with fair precision by modifications of the closed-can, gamma-only assay method, using commercially available or similar equipment. Coefficients range from <1 to 91 percent. Emanation varies considerably within each mine and area, but distinct differences among major mining areas were found, ranging from 7.5 percent for Moss Back Member, Chinle Formation, Southwest Lisbon Valley, Utah, to 56.6 percent for Ft. Union Formation (?), Powder River Basin, Wyoming. Coefficients also vary with (1) uranium mineralogy; (2) radium mineralogy; (3) lithology of host rocks; (4) grain size of uranium and radium minerals; (5) comminution of ore; (6) estimated porosity and permeability; (7) moisture content; (8) ore grade; (9) supposed mobility of deposits; age of deposits is unknown but limited by (10) age of host rocks which shows only doubtful correlation with emanation. Data obtained may be used to evaluate effects of investigated parameters on radon concentration in mines and thus to select efficient control measures. Drill-core emanation data allow estimates of probable radon problems in undeveloped deposits.

Jan 1, 1978

By C. W. Owings

A few of the more progressive mining companies have taken precautions to safeguard employees or man-trips. Specially constructed men-cars -have been provided with special devices or mechanisms to stop the cars on slopes, if the hoisting cable should break. Cars have been equipped with safety chains to connect and hold them together if a coupling should break. Steel frames covered with heavy wire netting have been placed over cars to reduce injuries to the riders from roof fails on slopes. A safety cable passing from the front car to a point above the cable socket on the slope hoisting cable is used frequently as a precaution in case the socket loosens o the main cable breaks at the socket. Such devices are commendable, but the percentage of man-cars and man-trips protected is relatively small - entirely too small. Man-trips that travel level haulage roads are rarely protected safety devices, and haulage roads are seldom inspected by mine officials to determine the condition of roof and ribs.

Jan 1, 1935