Search Documents

By D. V. Keller

Black lung disease, or paeumocomosis, is a serious health hazard for workers working in a coal mine. Though the exact cause of black lung disease is not known, it is certain that prolonged inhalation of fine coal particles, ever present in the mines, does give rise to black lung disease. For a long time, it also has been known that limestone applied to coal dust mine surfaces tends to hold down coal dust thus preventing it from refloating in the air of the coal mines. Since the humidity in the mines may be generally high, this also might be an important factor in the particular substrate system behavior. Fine solid particles stick to other particles and surfaces very indiscriminately. The term adhesion is used for the phenomenon of attachment of particles to surfaces whereas cohesion is used for the phenomenon of attachment of particles to each other. The measurement of the force of adhesion of coal particles to coal substrates presents a great problem, especially in the case of particles in the size range of a few microns. These micron sized particles are at the limit of the resolution of the optical microscope and therefore an electron microscope has to be used for this purpose. The forces of adhesion between these particles and substrate may be very strong and can exceed the weight of the particle by four to five orders of magnitude.

Jan 1, 1973

By W. D. Musgrove, B. W. Gandrud, A. C. Richardson

"INTRODUCTION The Cahaba coal field is the second largest coal—producing area in Alabama. This field underlies parts of Shelby, Jefferson, St. Clair, and Bibb Counties and has an area of about 270 square miles. The Cahaba formations contain a number of coal beds, about 8 of which are mined at present. Although the area contains many folds and faults, samples from various mines and beds indicate that, except for the variation in ash content, the coal from this field is very uniform in character and quality. It is a high-volatile bituminous coal used chiefly for steam-raising purposes and domestic fuel. The coal as mined usually contains too high a percentage of impurities to be marketed without some preparation. The majority of the mines have washing plants in which jigs are the favorite type of equipment, although at some mines tables are used for cleaning the slack sizes. The washing characteristics of the coal from the Cahaba field are very uniform and differ from those of the near-by Warrior field, in that the coarser sizes contain a much lower percentage of bony material than the finer sizes. In general, the bone increases with decrease in size. It breaks into thin flakes, making difficult its elimination in the cleaning process, and gives rise to what is known among the washery operators of the Cahaba field as the ""rash problem.""A previous publication 5 referred to rash from the standpoint of jig operation and suggested some means of handling it with jigs. This report presents the results of table tests on two samples of fine coal from the Thompson and Woodstock beds, respectively, of the Cahaba field to determine the influence of rash on table efficiency.This investigation has been made in connection with the study of coal-washing problems now being conducted by the U.S. Bureau of Mines and the University of Alabama, with the cooperation of the different coal operators of Alabama."

May 1, 1934

By G. L. Oldright

[Processes by which silver alone is extracted from ores that also cant contain base metals are usually associated in the mind of the period when mines were changing from the production of noble metals to the production of base metals containing noble metals as a by-product. In this transition period the mixed arcs of the partly oxidized ore zone had to be treated instead of the free-milling ore that had been treated in the past or the deeper-lying sulphide ores that were to be smelted subsequently under improved economic and technical conditions.]

Jan 1, 1929

By J. E. Tress

The Bureau of Mines prepared submicron tungsten powder by reducing tungsten hexachloride with hydrogen. The particle diameters of the resulting tungsten powders ranged from 0.015 to 0.046 micron. Within the limits of the variables investigated, no clear-cut correlation was found between process conditions and final size of the powder. Oxygen was the major contaminant in the product; being present both as an adsorbed gas and as suboxides of tungsten. Studies showed that the powder yielded compacts of approximately 45 per-cent of theoretical density when compacted mechanically. Low-temperature sintering produced more rapid densification in these compacts than in compacts prepared from conventional powders. Adding up to 20 percent ultrafine powder to conventional tungsten powder caused an increase in density upon compaction with maximum densification occurring at approximately 12 percent ultrafine powder.

Jan 1, 1966

By Launa G. Mallett, Charles Vaught

This report is intended to help mine safety trainers better prepare to teach the influx of new underground coal miners who are entering the industry. This is done by identifying two different approaches to instruction and discussing the ways they may affect how well prepared new hires are to deal with a dynamic and hazardous workplace. One approach is based on the use of a syllabus. Those using a syllabus are more likely to rely on lecturing or direct instruction. This is a good way to get across factual information, but does not provide a context within which miners can fit the discrete facts so that they form an integrated whole set of concepts, principles, and skills. The other approach is based on the use of a curriculum. Those using a curriculum may be more likely to help miners integrate concepts and skills that give them an overall picture of the complex mining environment and how they fit into the workplace. This will better prepare them for the decision-making and problem-solving activities that will help them work safely and productively

Jan 1, 2008

By Jack R. Woodyard

Bonding angles, promotion energies, and relative atomic sizes can be estimated through the solution of a set of algebraic equations generated from simple atomic models, and quantum mechanical parameters such as bond strength can be estimated from simple, hydrogenic form-wave functions. The precepts of The Engel-Brewer Theory are melded with the "Crystal Approximation Model" to produce atomic-structure models making these predictions, The two-valence-electron case is presented in this report. For the candidate atoms Be, Mg, Ca, Sr, and Ba the calculated promotion energies agreed within a few percent of their experimental values. These atomic parameters determine the possible crystal structure of the candidate atoms when alloyed. This is part of the effort at the U.S. Bureau of Mines to develop methods for alloy design in response to requirements for new high-performance alloys that conserve critical or rare materials.

Jan 1, 2010

By Douglas F. Scott

Zinc, silver, copper, and tungsten are the principal minerals in Dardanelles RARE II area (No. 4982). Zinc with associated silver and copper occurs in a persistent shear zone in metasedimentary rocks and in a massive sulfide vein; tungsten occurs as disseminated scheelite in a tactite zone along a metasedimentary-intrusive rock contact. Since 1883, approximately 100 lode mining claims have been recorded, mainly it the eastern portion of area No. 4982 (fig. 1). Extensive workings on the Alhambra Prospect indicate past production; however, no records were found for the prospect. At the Alpine Mine, 500 tons of tungsten ore had been mined before 1943 (Hopson, 1943, p. 1) and possibly 1,000 tons of tungsten ore mined by 1947 (Benson, 194/, pp. 2).

Jan 1, 1982

By George W. Healy

The direct retorting of zinc sulfide concentrates in the presence of lime and carbon was examined on a laboratory scale with ten-gram charges of loose mix or fifteen-gram ones of pellets. A slow stream of nitrogen swept through the furnace tube over the boat of reactants, carrying with it the zinc vapor, which condensed on a rolled-up steel sheet near the exit, permitting weight of zinc produced to be obtained after completion of a run. Variables explored were percent of theoretical reagents, temperature, and time. During the runs gas samples were analysed periodically, and the content of CO2, CO and nitrogen were obtained. The quantities of the carbon gases could be calculated because the nitogen flow rate was measured. The gases were also examined for sulfur species, but neither COS nor SO2 could be detected at maximum sensitivity. Zinc recovery increased with excess carbon and lime and with temperature. It ranged from 77% at a ten percent deficiency to 90% at a ten percent excess at 1100°C. Going to 1200°C and theoretical reagents gave 93% recovery. Increasing time from 200 minutes to 300 minutes increased zinc yield by up to 10%. Results from sphalerite and a commercial concentrate from AMAX gave generally similar results. The reaction rate of zinc sulfide as sphalerite and of calcined sphalerite indicated that the latter reacted almost twice as fast, and recovery of zinc was five percent higher. Though the retorting step using sulfide, lime, and carbon proved to be non-polluting, it was feared that on storage the calcium sulfide in the residues would decompose, giving off noxious gases. Consequently the stabilization of the residues by oxidation was essayed. Because of the presence of unreacted zinc sulfide, the first product of oxidation was S02. Reaction of CaS to CaSO4 was incomplete, going from 20% at 800°C to 90% at 1200°C. Thus the non-polluting nature of the process as a whole is in doubt, and its economics are likely to be unfavorable compared to the traditional way of calcining the concentrates, followed by retorting of the oxide with carbon.

Jan 1, 1982

By H. P. Greenwald, Irving Hartman, H. C. Howarth

"INTRODUCTION A report of tests of seven small pillars formed from the Pittsburgh coal bed in the Experimental coal mine was given in Technical Paper 605 5/ Five additional pillars were tested between July 1939 and. October 1940. The data obtained, in the later tests permit an extension of the conclusions reached in Technical Paper 605, which appears to be important enough to the mining industry to justify a progress report that will explain briefly what it is and how it was obtained. Full detail of the tests will appear in a second technical paper, preparation of which is deferred so that results of pillar tests now under way my be included.DESCRIPTION OF TESTSExcept for minor improvements in operating details, the five additional tests were made as described in Technical Paper 605, pages 2 to 7. Briefly, the desired pillar was formed from the coal bed, by excavating a passage around it (no explosives were used), and enough material was removed from above to permit installation of the assembly used for applying pressure. Each pillar was tested resting on its original fireclay floor, which was restrained from lateral flow by a ring of concrete. Vertical and lateral movement of the pillars in two directions as measured carefully in all tests."

Jun 1, 1941

By H. Kenworthy

[Experimental studies were made to develop a laboratory technique for direct removal of cadmium and germanium from sphalerite concentrates. Cadmium- and germanium-bearing concentrates from the Illinois-Kentucky fluorspar field were sound to be, amenable to an inert atmosphere fuming process for removing these two moats in the form of gaseous sulfides. Treating the condensed fume by pyrometallurgical methods upgraded the material end provided a means of partly separating the constituents. Cadmium was concentrated about 35:1 arid germanium about 300:1. The extractive investigations were supplemented by vapor-pressure studies on the sulfides of germanium to obtain fundamental data for larger scale laboratory conditioning and control when treating the zinc concentrates. Vapor-pressure curves were developed for synthesized monosulfide and disulfide The results of these- investigations indicate the possibility of significantly increasing the recovery of cadmium from zinc concentrates. Comparison with present recovery of germanium cannot be made, since commercial recovery data arc not available.]

Jan 1, 1956

By W. K. Overbey

Surface fracture trace density, changes in roof rock type, and topographic unloading due to drainage were mapped for the mining areas located in the Blacksville-Osage, W. Va., quadrangles to investigate their influence on mine roof falls. Using these factors, a technique was developed to predict probable roof fall areas ahead of projected mining operations. As a feasibility test of this proposed technique, areas were delineated where one, two, and all three of these factors were operating to formulate a "potential hazard map" for comparison with roof fall observations that were made. The limited evidence suggests that in combination these factors are reliable predictors of where roof falls are likely to occur. This technique promises to be a useful tool in planning mining operations.

Jan 1, 1973

By F. S. Kendorski

This report presents the results of a search for viable-self-drilling roof bolt concepts, detailed development, design, and manufacture of such bolts that drill their own holes, and testing in the laboratory and in the field in two different coal mines of three self-drilling roof bolts. Three new types of bolts were designed and tested, which drill their own holes and then anchor in continuous operation. These were a spring-actuated mechanical expansion shell, a slot and wedge, and a self-contained resin anchor bolt. Such bolts when fully developed for mine use would allow safer and remote installation of ground support and increase productivity. Recommendations are given for further work to improve drilling and anchorage performance.

Jan 1, 1979

By Edward J. Murphy

A comparative study has been made by the Bureau of Mines of several analytical methods for determining carbon monoxide and nitrogen oxides in toxic gases produced by the detonation of explosives. Laboratory and field methods and detector-tube devices are described. Analytical results are compared, and reliability of the various methods is discussed. INTRODUCTION In all underground mining there is ever-present danger to persons from possible overexposure to carbon monoxide and nitrogen oxides created by explosives or blasting agents. These health hazards, recognized for many years, led to the early establishment by the Bureau of Mines of specific requirements regarding fumes generated by explosives authorized for use in underground coal mines in the United States.3

Jan 1, 1961

By Edward L. Wilson

A general computer program is given for the linear elastic static analysis of complex structural systems. These elements have special advantages for the analysis of massive underground structures such as mine structures and above ground structures such as arch dams. New finite elements are developed which are useful in the analysis of two and three dimensional solids. Examples are given which illustrate the accuracy of the elements. A description on the use of the program and a FORTRAN IV listing are given in the Appendices.

Jan 1, 1971

By Lindsay D. Norman

Four chloride and seven fixed-nitrogen processes for recovering manganese from domestic resources are described. The chloride processes are divided into two classes (leaching and chloridization) depending upon the major operation responsible for converting the manganese minerals to the chloride from which manganese oxide products are obtained. The fixed nitrogen processes, all of which yield high-grade manganese oxide products, are essentially either leaching or roasting processes. The 11 processes include HC1 leach, HC1 chloridization, HC1 chloride volatilization, CaC12 chloride volatilization, NO2 leach, HNO3 leach, HNO3 ?NO2 leach, H3 ?CO2-H2O system leach, (NH4)2SO4 leach, (NH4)2SO4 roast , and ammonium salt roast .

Jan 1, 1963

By A. B. Hooker, Ilsley. L. C.

"Several writers have called attention, in the technical press, to the possible failure of flame safety lamps in coal-dust laden atmospheres. Such writers question the safety or a flame lamp that has been proved only in atmospheres containing methane, believing that the resistance of the lamp to explosion would be lessened it coal dust constituted a part of the explosive mixture.If this be true, it follows that any series of tests devised to prove the safety of flame lamps for use in gaseous and dusty coal mines should not only embrace tests in mixtures containing various proportions of methane, but also in some of the tests the effect of adding coal dust to the explosive gaseous mixtures should be investigated.Some attention has been given this question by investigators, but the more common practice has been to make all tests in gas and air mixtures only, using methane when it was readily available. Apparently the English Accident Committee (1879-1886) who conducted tests upon 250 different lamps did not use coal dust in their tests. The first British requirements for the testing of safety lamps, issued as a result of the Coal Mine Act of 1911, made no mention of tests with coal duet.The Austrian Fire-damp Committee (1890) conducted a series of tests in which coal dust was used in some of the tests. In certain tests, the addition of coal dust apparently lowered the resistance of the lamp 1 meter per second. The Belgium investigators, Messrs. Watteyne and Stassart, conducted a series of tests in 1904 in which coal dust was used in a few tests without any marked difference in safety."

Dec 1, 1920

By Lindsay D. Norman

Four chloride and seven fixed-nitrogen processes for recovering manganese from domestic resources are described. The chloride processes are divided into two classes (leaching and chloridization) depending upon the major operation responsible for converting the manganese minerals to the chloride from which manganese oxide products are obtained. The fixed nitrogen processes, all of which yield high-grade manganese oxide products, are essentially either leaching or roasting processes. The 11 processes include HC1 leach, HC1 chloridization, HC1 chloride volatilization, CaC12 chloride volatilization, NO2 leach, HNO3-NO2 leach, NH3-CO2-H2O system leach, (NH4)2SO4 leach, (NH4)2SO4 roast, and ammonium salt roast.

Jan 1, 1963

By Bruce D. Hanson

The Bureau of Mines conducted a series of ignition tests with two types of conical bits (plumb bob and pencil) used on continuous mining machines, to determine their ignition potential at various bit speeds, cut depths, and wear conditions. The tests were conducted using single bits mounted on a 34-in-diam drum in a Bureau ignition test facility. The bits impacted blocks of Berea sandstone in a 6.5 pet methane atmosphere at various bit speeds and cut depths. In a new condition, the plumb bob bits were considerably more incendive than the pencil bits, causing ignitions in 32 of 35 tests at 60 rpm, compared with ignitiolls in 2 of 22 tests for the pencil bits. The results from new bit testing also show that reduction of bit tip velocity to 180 fpm does not eliminate ignition potential. When subjected to progressive wear, bits of both types were more incendive when they were locked in place, unable to rotate, than when they were free to rotate.

Jan 1, 1983

By P. J. Watson

The objective of this study was to prioritize the potential risks nuisance and biologically active dusts and fumes present in metal and nonmetal mines. This was accomplished by ranking numerical values derived from a matrix formula calculation that took into account dose, mine population, and sampling size. Data used in these calculations were obtained from the Mine Inspection Data Analysis System (MIDAS). The dusts determined to have the highest risk potential were quartz respirable particulates, mine dust, cristobalite respirable particulates, welding fume components, and nuisance respirable dust. Other dusts and fumes that were not ranked in this study, due to small sampling population, but which show a potential risk, include asbestos, talc, hydrogen cyanide, organic compound dusts, arsenic, metal dusts, and metal and nonmetal fumes.

Jan 1, 1987

By Robert Roby

The Mouat copper-nickel deposit in Stillwater County, south-central Montana, was examined by Paul T. Allsman, an engineer of the Bureau of Mines, in 1939. Because of the strategic importance of nickel, a project was executed by John East, Jr., J. J. Naughton, and E. W. Newman, engineers of the Bureau, to further delimit some of the copper-nickel sulfide-bearing bodies that had been discovered by the Anaconda Copper Mining. Co. in 1937 and to investigate the central part of the deposit, which had not been drilled previously. This report is based largely upon the results of the. Bureau of Mines investigation and the results of exploration by the Anaconda Copper Mining Co. In addition, a brief description is given of some other copper-nickel sulfide-bearing deposits along tho Stillwater Complex.

Jan 1, 1949