Search Documents

By C. E. Saxon, F. E. Cash

"Adequate lighting for all mining operations would unquestionably tend to promote both safety and efficiency; this would be true not only for men but also for the animals that man impresses into service in mines. The Markeeta Coal Co. and the Alabama Fuel & Iron Co. both operating mines in Alabama, have found that equipping mine mules with portable electric lights is more efficient, much more humane, and far more safe for both men and animals then the more or less usual method of forcing the animal to do its work essentially in darkness.This report is intended to give the mining industry data, that will aid in trying to bring about safe and efficient operation of mines.The authors desire to thank Charles F. DeBardeleben, president, Fred R. Bell, general manager, Hewett Smith, C. H. Shepherd, and R. A. Sensing, superintendents for the Alabama Fuel & Iron Co.; and Charles F. DeBardeleben, Jr., president, and H. M. House, superintendent for the Markeeta Coal Co., for their cooperation in furnishing the data for this paper.The eight mines operated by the Alabama Fuel & Iron Co. and one operated by the Markeeta Coal Co. in Jefferson and St. Clair Counties, Ala., are the only mines in Alabama where mules are provided with portable electric lights, and there are few if any mines in other States in which this system is in use.These two companies are convinced that equipping all mine mules with good lights decreases underground haulage cost by animals by prolonging the useful life of the animals, increasing their efficiency, lessening haulage wrecks and delays on haulage, and increasing production. Last but not least of the advantages would be the more humane treatment of the animals.The nine mines are developed by slopes along the dip of the coal bed, with double-room entries on 200- to 300-foot centers turned right and left off the slopes and with approximately 1 per cent grade in favor of the loads. Rooms are driven up or diagonally up the pitch from these entries.A surface hoist delivers the empties from the surface to the entry sidetracks at the slope and pulls the loads to the surface. From these sidetracks, mules pull one to four wooden cars, each of which holds 1-1/2 to 2-1/2 tons of coal, deliver the empties to the rooms and entry faces, and pull the loads to the slope sidetracks. The mule haul varies from 100 to 3,000 feet; there are no locomotives or trolley wires in any of these nine mines, seven of which are rated as gassy and two as nongassy by the Alabama state Mining Department."

May 1, 1933

By David C. Byrne

PURPOSE: Evaluate practical technological advances in hearing protective devices for use in different mining environments. RESEARCH SUMMARY: Previous NIOSH research shows that miners develop hearing loss much more quickly than nonoccupationally noise-exposed individuals. Also, miners experience a greater severity of hearing loss than would be expected for nonoccupational noise-exposed persons of the same age and sex. As described in the National Occupational Research Agenda, problems created by occupational hearing loss include (1) the reduced quality of life due to social isolation and unrelenting tinnitus, (2) impaired communication with family members, the public, and coworkers,(3) a diminished ability to monitor the work environment (e.g., warning signals, equipment sounds, etc.), (4) lost productivity and increased accidents resulting from impaired communication and isolation, and (5) expenses for workers’ compensation and hearing aids. Although the elimination of hazardous noise is the ideal long-term solution to the noise problem, miners will likely need to rely on personal hearing protection in certain situations for quite some time. However, it is well known that noise attenuation provided by hearing protectors as they are worn during everyday use in the workplace is usually worse than when tested under laboratory conditions. Additionally, workers may refuse to wear their hearing protection for any number of reasons. Therefore, this project was initiated to evaluate practical technological advances in hearing protectors, with an emphasis toward optimizing the balance between effectiveness, comfort, overprotection, and communication ability. Currently, the necessary in-house laboratory facilities and research techniques are being finalized. Individual experiments are planned that involve analysis of new hearing protector technology under both laboratory and field conditions. The laboratory components are to consist of con-trolled studies using human subjects and/or an anthropometrically correct artificial test fixture to evaluate the adequacy/effectiveness of various hearing protective devices. Field studies are planned to determine the actual usefulness and practicality of the hearing protectors as used in diferent mining environments. Recommendations can then be offered to the mining community regarding correct earplug/earmuff usage that maximizes recognition of hazard/warning sounds while adequately protecting the miners’ hearing.

Jan 12, 2000

By Danny Hagood

The drilling of horizontal boreholes as a means of degasification in advance of mining has been tried at Jim Walter Resources, Inc., No. 4 Mine. In a joint venture with the U.S. Bureau of Mines, a series of horizontal drainage boreholes have been drilled in the panels of an advancing continuous miner section with impressive results. The combined methane gas production rate has ranged from 205,000 to 680,000 cfd (cubic feet per day} with individual "in-seam" horizontal holes producing up to 332,000 cfd. The methane liberation from the ribs for the entire panel length has decreased from an average of 8.75 cfm (cubic feet per minute) per 100 feet of entry to 4.05 cfm per 100 feet, a 54 per cent reduction. The actual gas concentration as measure at the surface discharge point normally ranges from 85 per cent to 95 per cent methane. As a consequence of the significant reduction in methane liberation rates from the panels of the section, a 50 per cent increase in productivity from the section has been realized.

Jan 1, 1983

By Thomas M. Barczak

Longwall operators are again pushing the envelope in terms of life expectancy for longwall shields. State-of-the-art shields are now expected to last more than 60,000 loading cycles, twice the life expectancy compared with those of a decade ago. A review of trends in shield design shows that shields continue to increase in both size and capacity. Some state-of-the-art shields now weigh over 30 tons and provide up to 1,200 tons of support capacity. Although life expectancy has increased and modern shields are structurally more reliable, premature failures do still occur. This paper provides an engineering and operational assessment of shield design and provides key points to observe in what causes premature shield failures. Design practices to improve structural margins of safety that will prevent premature failures from occurring are also examined. A survey of recent shield failures is provided, as well as trends in shield design and how they might impact the performance and longevity of a shield. Hydraulic failures are more common than structural failures. Although hydraulic failures occur on all aging longwall shields, they often go undetected for long periods, resulting in degraded support capacity that can lead to serious ground control problems. The fundamentals of shield hydraulics are described in order to evaluate hydraulic failures that plague all shields at some point in their service life, and practical methods to detect hydraulic failures are examined. The paper concludes with recommendations for inspecting damaged shields and safety precautions regarding their continued use.

Jan 10, 2000

By C. P. Mabie

This report summarizes studies by the Bureau of Mines in developing a simple method for estimating the phosphorus pentoxide (P205) content of finely ground sedimentary phosphate ores and beneficiated products. The method used involved leaching, filtration, and precipitation. The Bureau found that measurement of the volume of ammonium phosphomolybdate precipitate obtained from samples containing 16.8 to 37.7 percent P205 and the use of an appropriate calibration curve permitted estimates of percentage of P205 content accurate within ± 1.1 to ± 2.6 percent, respectively, at the 95-percent confidence limits. Incidental to mineral dressing and petrographic investigations of western phosphate ores in 1959, the Bureau of Mines undertook development of a simple process-control method for rapid on-the-spot evaluation of phosphate-mineral recovery. Because of the fine-grained and obscure character of western phosphate ores, chemical, rather than microscopic or petrographic, techniques were investigated. The described method involves acid decomposition of the ore or product, filtration, addition of ammonium molybdate reagent to the filtrate, and centrifuging and measuring the volume of yellow ammonium phosphomolybdate precipitate produced.

Jan 1, 1961

By Errol D. Sehnke

This U.S. Bureau of Mines report provides detailed information on worldwide alumina production capacity by plant and country. The information was compiled from a variety of domestic and international sources and was based on information available to the Bureau through December 31, 1993. Capacity data represent announced installed and planned capacities and do not necessarily reflect a Bureau of Mines judgment of actual plant operating levels or timing of planned expansions, The year-end capacity is the ?nameplate" capacity or estimated production capacity, whichever is larger.

Jan 1, 1993

By Donald O. Capstick

The local geology, the lack of recorded mining activity, and our field investigation and associated sampling indicate a low potential for mineral resources. Claim records and the literature review failed to show any lode or heavy mineral placer mining claim locations that are definitely in the area or anomalous mineral concentrations in the study area. Field investigations revealed no claims, prospects, or mineralized areas.

Jan 1, 1982

By G. E. McElroy

"The development of certain mines in the East Tintic mining district, Utah, has been hindered considerably by the presence in the rock strata of heavy irrespirable gases which at times flood the lowest working places, as well as by abnormally high rock temperatures in the lower horizons. A study of these features was completed in the spring of this year, and the information obtained is summarized here.Heavy gases.Only four mines have been affected to date by the presence of heavy gas, and only one of these is producing lead-silver ores in quantity. These four embrace a territory extending about three miles north and south and about two miles east and west, while both within and fringing on this territory are a number of prospects which have not been affected.Thus far no fatalities have resulted from gas inflows, but a number of men have been temporarily overcome, and a few have had narrow escapes from death by suffocation. That the record is not more serious is mainly due to the fact that the gas inflow, as a rule, is relatively slow, mining operations have been quite carefully conducted, and the presence and extent of a gas inflow can be easily determined by its extinguishing action on the flame of miners' lights.When first encountered, about 1910, gas inflows occasioned much lost time. In some months the lost time averaged as much as ten days, while one mine cites for a certain month a maximum of 26 days lost out of a possible 28 working days. With improvements in mechanical ventilation and the passing of time, interference with work from the presence of gas has gradually lessened. During the last few winters, the main trouble has been with the mines being flooded with gas overnight when fans were not operated, although men have been driven out of the lowest development openings several times each winter with fans operating. At present, the main danger is in the lowest development openings having only one exit, wherein men might be trapped and possibly suffocated during an unusual and extremely rapid inflow of gas, or during an ordinary inflow, should the one source of power for the fan be disabled."

Aug 1, 1921

By J. M. Singer

The Bureau of Mines investigated the threshold of dispersal of monolayers and piles of rock dust, anthracite, and Pittsburgh seam coal dust in a small wind tunnel that simulated a coal mine gallery, with the objective of preventing or limiting the formation of flammable dust clouds. The effect of selected variables on entrainment velocity was examined. Mode of entrainment and flow processes in the wake region of dust configurations were investigated by means of high-speed motion pictures. Significant results were as follows: 1. Local minimum air velocities required for dispersal were only slightly higher for shallow dust ridges than for dust particles. 2. Minimum velocities for entrainment of dust particles from smooth glass and coal surfaces increased in the order rock dust, anthracite, Pittsburgh seam coal. 3. The mechanism for dispersal of dust poles depended significantly on dust pile geometry, cohesiveness of dust, bulk density and compaction of dust, adhesive surface, and vibrations perturbing the supporting surface.

Jan 1, 1969

By Phillip N. Yasnowsky

This Bureau of Mines publication tabulates State taxes levied on nonfuel minerals that have the characteristics of a severance tax.

Jan 1, 1978

By Roy T. Sorensen

The Bureau of Mines has investigated the recovery of cell-grade alu-mina by RCI leaching of calcined kaolin in the alumina miniplant at its Boulder City (NV) Engineering Laboratory. Classification and thickening were used for separating aluminum chloride leach liquor from the siliceous residue generated in the acid leaching step of the clay-HCI process. Coarse solids were classified from fines at 115 mesh and countercurrently washed in three additional spiral classifiers. Fines were treated in a conventional five-thickener, countercurrent decantation circuit. When this method was applied to the solids-liquid separation of slurry from RCI leaching of minus lO-mesh calcined kaolin, 75 pct of the residue reported as classifier sands and 25 pct as thickener underflow. Predicted individual classifier and thickener area requirements were 6 and 25 ft2/tpd, respectively. Total thickener circuit flocculant requirement was 2.4 lb/ton solids. Aluminum chloride pregnant liquor was produced that analyzed 8.4 pct A1203 and contained more than 97 pct of the alumina in the liquid phase of the slurry. Bench-scale settling tests were used to correlate fines content of leach residue to thickener area and flocculant requirements.

Jan 1, 1983

By J. E. Hamak

This publication contains analyses and related source data for 266 natural gas samples from 20 States and 2 foreign countries. None of the analyses have been previously published in annual reports. All samples were obtained and analyzed as part of the U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1992

By R. H. Grau, A. Sainato, S. J. Schatzel, T. M. Kohler, A. T. Iannacchione

This Bureau of Mines research study found gas emission rates from an advancing face, and flows and pressure of gas from an exploration drill hole were dependent upon the geology of salt encountered in a domal salt mine. Normal production-grade "pure" salt adjacent to an anomalous' zone was found to have a methane emission rate of less than 5 ft3/ ton (0.1 m3/t) of mined salt from a room advanced by a continuous miner. Extremely low gas flows [less the 4 ft3/h (0.1 m3/h)] and lack of pressure buildup were also observed from this normal salt in a 154-ft (47-m) exploration drill hole. These data indicate that methane emissions should not be a problem when mining in this type of salt. In the adjacent anomalous zone, methane emission rates ranged from 15 to 70 ft3/ton (0.4 to 1.8 m3/t) of mined salt from an advancing face. Gas flows of approximately 42 ft3/h (1.2 m3/h), and pressures in excess of 900 psig (6,200 kPa) were observed in an exploration drill hole when the anomalous zone was encountered. This information suggests a greater methane emission hazard from the anomalous zone than from the associated normal salt. If this trend of increasing emissions problems associated with anomalous zones of salt is common with similar anomalous zones encountered or observed in other domal salt mines, then special control strategies should be employed to minimize this potential mining hazard.

Jan 1, 1984

By John R. Benham

The Bureau of Mines examined the Bear Canyon RARE II area in 1982. The area has no identified mineral deposits. The few claims that were located in the study area are devoid of any workings. No concentrations of economic minerals were found in the samples taken. There are no mineral, geothermal, or oil and gas leases in the area; the nearest oil well is 10 mi (16 km) east. The nearest mining operation was the Ruby Gold Placer worked in 1914, 7 mi (11 km) southeast (Hart, 1966, p. 45); the Pliocene Paso Robles Formation which contained the gold does not extend into the area. SETTING The Bear Canyon RARE II area covers 19.7 sq mi (51 sq km) or 12,600 acres (1500 ha) in west-central California. It lies in the Santa Lucia Range 10 mi (16 km) southwest of King City and adjoins the southeast side of the Ventana Wilderness. It is 10 mi (16 km) from the Pacific Ocean. Primary access is by the San Antonio River road on the Hunter Liggett Military Reservation, which parallels the area's southern border. Further access to the area's interior is by jeep and foot trails.

Jan 1, 1983

By L. M. Demers, D. C. Kuhn, N. El-Ayouby, C. F. Stanley

"Oxygenated metabolites of arachidonic acid (MJ are produced by the alveolar macrophage (AM) and have been shown to mediate inflammatory reactions. We therefore assessed the production of eicosanoids by AM harvested from the lungs of rats ex· posed to a bituminous coal dust for 2 wk in an inhalation chamber in order to determine if AA metabolism was altered in a manner that may promote an inflammatory response in the lung. Exposure to coal dust resulted in a 66% increase in the number of AM harvested, an increase in thromboxane A2 (TxA;i) and leukotriene 84 (LTB,j) production to 222% and 181% of control values, respectively, and a decrease in prostaglandin E2 (PGE:i) production to '62% of control values. In AM harvested from rats allowed to breath clean air for 2 wk following coal dust exposure, PGE2 production returned to control levels but TxA2 and LTB4 production remained elevated. The TxA2 synthesis inhibitor UK 38,485 reduced TxA2 production in dust-exposed AM both immediately and 2 wk following exposure. Thus, exposure of rats to coal dust significantly alters the metabolism of AA in AM, with potentially important aspects of AA metabolism remaining altered even after a 2-wk recovery period. Based on the established role of eicosanoids in inflammatory and fibrotic processes, these results suggest that the alteration of AM eicosanoid production as a result of the inhalation of coal mine dust may be an important factor in the pathophysiology of coal workers' pneumoconiosis.The authors are grateful to Joan Greenwood and Barbara Scheetz for their excellent technical assistance and to Brenda Pavone for the preparation of the manuscript. This research was supported by the U.S. Department of The Interior's Mineral Institute Program administered through the Generic Mineral Technology Center for Respirable Dust under grant 1135142.Request for reprints should be sent to Douglas C. Kuhn, Ph.D., Department of Pathology, The M.S. Hershey Medical Center, Hershey, PA 17033.INTRODUCTIONPulmonary alveolar macrophages (AM) are activated by foreign particles and microorganisms that enter the small airways (Kass et al., 1966; Herscowitz, 1985). This defensive reaction involves phagocytosis, lysosomal enzyme release, and the generation of reactive oxygen species by the AM (Snella, 1986; Rich et al., 1987). A number of agents, including phorbol esters, zymosan, adenosine diphosphate, organic hydroperoxides, and calcium ionophore, have been shown to activate the AM in vitro (Badger, 1986; Marshall and Lands, 1986; Snella, 1986). The AM response to these activators appears to be mediated in part by the oxygenated metabolites of arachidonic acid (AA) (Bertram et al., 1988; Demers et al., 1987; Mcleish et al., 1987).The AM may metabolize AA through cyclooxygenase- and lipoxygenase- catalyzed pathways to produce a variety of eicosanoids including prostaglandin (PG) E2, thromboxane (Tx) A2, leukotriene (LT) B4, LTC4, LTD4, and several hydroxyeicosatetraenoic acid derivatives (HETEs) (Willis, 1970; Camp et al., 1983; Poubelle et al., 1986). The production of these eicosanoids may enhance the. defensive ability of the challenged lung since they stimulate chemotactic cell recruitment to the site of invasion, enhance extravasation of circulating immune cells, and promote local vasodilatation. However, continued stimulation of the AM population, with the consequent production of proinflammatory eicosanoids, may ultimately enhance the disease process by contributing to chronic bronchoconstriction, fibrosis, and the persistent release of toxic oxygen species."

Jan 1, 1990

By D. Harrington

Approximately 2,000 persons are killed annually in the coal mines of the United States. There is no question that this number is at least double and probably treble what it should be and by all means the least excusable of the fatalities are those caused by explosions and fires. Fatalities from explo- sions and fires in coal mines are almost invariably caused by carelessness or negligence. Table 1 indicates that the fiscal year ending June 30, 1931, ras by no means a satisfactory one as regaris either the number of explosions or the number of persons killed by them. This tabulation lists all ignitions to which the attention of the personnel of the safety division was called and in- cludes not only major disasters, but also explosions in which fewer than five were killed, as well as several explosions from which no fatalities resulted. It will be noticed that last year there were 26 explosions in mines in 10 States of the United States, resulting in 217 deaths. In the previous year there were 34 explosions with a death list of 199, and in the year before there were 38 explosions with a death list of 139. Hence, the past fiscal year had distinctly a poorer record of fatalities from mine explosions than either of the two previous years. Of the 26 explosions in the past fiscal year, Pennsylvania had 7, West Virginic 4, New Mexico and Ohio 3 each, Alabama, Oklahoma and Washington 2 each, and California, Illinois and Indiana 1 each; the one in California was in a tunnel being driven for water purposes but giving off explosive gas (methane). In fatalities Ohio had the worst record with 38, Oklahoma came next with 45, then Indiane with 38, and Pennsylvania with 23; although Alabama had 2 ignitions and Washington 1, they caused no fatalities. Utch, Colorado, and Kentucky had no explosions reported by the safety division of the Bureau of Mines during the past fiscal year, but were on the list for the previous year, though in the case of Colorado there were no fatalities. On the other hand, Indiana and New Mexico, neither of rhich was charged with an explosion in the two previous years, were on the list for the past fiscal year; New Mexico had the bad record of three explosions, though fortunately with but a total of eight fatalities. Ohio reported 3 explosions to the safety division of the Bureau of Mines in the past fiscal year, 2 in the pre- vious year, and 3 in the year before that, or 8 in the past three fiscal years with 92 fatalities; all of these eight explosions were in open-light mines.

Dec 1, 1931

By F. E. Armstrong

A program with the objective of developing a fast, accurate instrumental method of analyzing mine dust for incombustible content has been underway in the Bureau of Mines for several years. Several prototype instruments making use of a gamma-ray backscatter technique have resulted. Although extensive laboratory testing has shown that these instruments are accurate under laboratory conditions, only extensive field testing will prove their ultimate practicality and usefulness. This report shows that under most conditions these devices are at least as accurate as the volumetric method and much faster in use. Other data obtained during the same study concerning mine dust are presented; these concern moisture content, sample bulk density distribution, and some particle size distribution information.

Jan 1, 1973

By J. C. LaScola

Development of methanometers and anemometers for underground use in coal mines is reviewed. The first semicontinuous recording methanometer was developed in 1961 in West Germany. The Bureau of Mines developed an instrument using; pellesters that was a continuous recording methanometer. Expansion of freon gas created a vacuum which pulled the methane-air mixture through a tube to an electrically heated, catalyst-impregnated pellester where the mixture was burned. The National Coal Board of England developed a continuous recording methanometer based on the principle of the Davy flame safety lamp. A thermo-pile was used to sense the hurt output of the flame. Finally the Bureau of Mines improved its methanometer by eliminating the freon gas and using a diffuser head to a monitor methane-air mixtures. Development of recording anemometers proceeded from the use of a photo¬cell and light source to sense rotation of the Biram-type anemometer blades to the use of a Hall detector to sense, rotation by measurement of electromagnetic pulses.

Jan 1, 1969

By Earl L. Hastings

Although the principal market for diatomite in the United States is in the East,4 production of the material is presently restricted to the West, because the deposits are larger, mining costs are cheaper, and the quality of product is better than that obtained from other domestic deposits. However, Tallahatta diatomite, occurring in Choctaw and Clarke Counties, Ala., has a freight rate advantage, which should encourage competition for those market that are now being supplied with the purer diatomites from the western deposits. For this reason, diatomite occurrences in the Tallahatta formation were examined by the Bureau of Mines and physical properties of samples from the deposit were determined to obtain additional data for use by any potential producer who wished to evaluate the material for its commercial possibilities. In 1894 K. M. Cunningham5 found that the buhrstone formation (now known as the Tallahatta formation) contained "siliceous shells of marine diatoms, radiolaria and foraminifera, thus being rather of the nature of tripoli or diatomaceous earth than of a true clay." Cooke6 and Semmes7 also reported the Tallahatta formation to be composed principally of diatomaceous earth with accompanying beds of sand, clay, and sandstone.

Jan 1, 1963

By Michael Hood

High-volume, low-pressure water jets have been employed for erosion of loosely consolidated rocks for centuries. This excavation method finds application in specialized circumstances even today. The use of high-pressure, low-volume water jets for rock cutting is more recent and was made possible by the development of high-pressure water pumps. Despite the benefits often claimed for these systems, high-pressure water jets still have not found widespread application. In this report, the U.S. Bureau of Mines has reviewed the various methods that have been employed using water jets to break rock and has focused on one method, termed "jet-assisted cutting," which was determined to be the closest to commercial development. The current state of knowledge based on laboratory and field experiences using this cutting method is reviewed, and possible future developments for this approach to excavation are assessed.

Jan 1, 1990