Search Documents

By Robert C. Steckley

The Bureau of Mines performed a fragmentation experiment in cooperation with Duval Corporation in a porphyry copper-molybdenum deposit near the Sierrita pit south of Tucson, Ariz. This experiment evaluated the fragmentation created in a 10-hole test blast having blasthole spacings of 25, 20, and 15 feet. The 10 blastholes were 9 inches in diameter and contained a total of 17,400 pounds of aluminized slurry blasting agent in 50-foot columns with 60 feet of stemming. Diamond drill core examination was the primary method used to determine the condition of the rock before and after blasting. These core examinations included study of length recovery, rock quality designation (RQD), weight recovery, and size distribution. Topographic surveys were used to measure the rock swell produced by the blast and a fragment size distribution was obtained for the broken material on the surface. Fragmentation to depths of 110 feet was excellent from the 15-to 20-foot blasthole spacing patterns. Good breakage was also produced by the 25-foot pattern although the effects of the blast were not so obvious. In situ leaching tests were not conducted. However, based only on size consideration, all three blasting patterns produced adequate breakage for successful leaching.

Jan 1, 1975

By Michael S. Miller

In 1985, at the request of the Bureau of Land Management, the Bureau of Mines studied a 50,57U-acre portion of the 90,345-acre Twin Peaks Wilderness Study Area (CA-020-619A) in order to evaluate its identified resources. The area studied is located about 45 miles northeast of Susanville, CA, in Lassen County, CA, and Washoe County, NV. The area is underlain by Tertiary volcanic, volcaniclastic, and intrusive rocks. Quaternary stream, lake, and landslide deposits overlie the older rock. There are no mines or mining claims in the study area. One mineral resource, pozzolan, was identified. Mining claims, inactive in 1985, have been staked adjacent to or near the northwest corner of, and also southeast of, the study area. Examination and sampling of 17 mineralized sites, delineated mostly by prior geochemical surveys, showed at least 30 million tons of subeconomic pozzolan resources and small or low-grade occurrences of gold, silver, copper, lead, zinc, nickel, molybdenum, zeolites and clay.

Jan 1, 1986

By N. Kumar Kittusamy

The purpose of this study was to assess the adequacy of the cab design and to determine the percentage of musculoskeletal symptoms among operators of mobile equipment used in mining and construction. A questionnaire was designed to assess demographics, work information, job history, and musculoskeletal symptoms in operators of heavy mobile equipment. Information concerning equipment included design of the seat/chair, levers, pedals, bothersome vibration, quality of ingress/egress from the equipment, proper preventative maintenance and repairs, and age of the equipment. The body regions that were evaluated included the neck, middle/upper back, low-back, shoulder/upper-arm, elbow/forearm, wrist/hand, hip, knee, and ankle/foot. Five hundred and eighty six operators completed the questionnaire. The results indicate that these workers are at risk for developing musculoskeletal disorders, and the need to quantify risk factors (i.e., whole-body vibration and static sitting postures).

Jan 6, 2006

By Michael L. Boninger, Erik J. Wolf, Rory A. Cooper

Although wheelchair users are regularly subjected to whole-body vibrations little research has been conducted to assess these vibrations or attempt to reduce them [2,3,5]. Most of the wheelchair and whole-body vibration research done to this point has been conducted on manual wheelchairs. Van Sickle et al showed that manual wheelchair propulsion over a simulated road course produces vibration loads that exceed the ISO 2631-1 standards for the fatigue-decreased proficiency boundary at the seat of the wheelchair as well as the head of the user [6]. In a study by Boninger et al [1], 66% of wheelchair users reported neck pain since acquiring their wheelchair. One of the key reasons believed to be the cause of pain, was the exposure to whole-body vibration. Kwarciak et al [4] and Wolf et al [7] performed similar studies using two methods of analysis to evaluate vibrations on suspension and non-suspension wheelchairs while descending curbs of varying heights. Both studies revealed no significant difference in the abilities of the wheelchairs to reduce the amounts of vibrations transferred to the wheelchair user. Although the efforts of wheelchair companies to reduce the amounts of whole-body vibration transmitted to wheelchair users through the addition of suspension systems is encouraging, the technology is not yet ideal. Additionally, the research to date has focused on manual wheelchairs exclusively, while little attention has been shown to powered wheelchairs. Methods This study includes the use of two suspension electric powered wheelchairs: The Quickie S-626 and the Invacare 3G Torque SP Storm Series. Each subject tested all of the configurations of the suspension wheelchairs. These included the Invacare with suspension, the Quickie with suspension set to three settings (most stiff, least stiff, and 50% stiffness), and both wheelchairs with solid inserts to act as non-suspension wheelchairs. Sixteen able bodied subjects have been recruited for this study so far. In each of the configurations of the wheelchairs, the subjects traversed an Activities of Daily Living (ADL) course. Vibrations were collected from a tri-axial accelerometer attached to a seat plate beneath the cushion during driving over the activities course. A mixed model ANOVA was used to determine if there were differences between suspensions based on Vibration Dose Value (VDV). Results Statistical analyses of the VDV data revealed significant differences between the six different suspensions over each of the obstacles in the activities of daily living course. Post-hoc analyses revealed that for each of the obstacles, significant differences existed between the Invacare suspension and the Invacare solid insert. For the Quickie power wheelchair the solid insert setting was not significantly different from the most-stiff setting for each of the obstacles

Jan 6, 2006

By Lorenz E. Sieffert, Lawrence B. Berger, H. H. Sehrenk, Ralph W. Stewar, James A. Gale

"INTRODUCTION The purpose of the investigation discussed in this article was to evaluate the toxic hazard from gases produced when thermosetting plastic materials used for electrical insulating purposes are burned or thermally decomposed in enclosed spaces. For brevity the term ""toxicity"" is used throughout the article to refer to the nature of gases produced under these conditions. A need for immediate study of the problem was created as a re¬sult of the battle damage reports received from various United States Fleet units. These indicated that the fumes emitted when these materials were burned or thermally decomposed had, in several instances, resulted in toxic atmospheres. In attempting to develop a suitable test method for evaluating toxicity, it was recognized that no single test procedure could be expected to duplicate the variety of conditions that might exist in an actual fire aboard ship. In view of the immediate need, however, it was felt that considerable information could be obtained, at least to classify comparatively the several types of materials as to the toxic effect caused by burning or thermal decomposition, through the development of a sound empirical method which could be applied to all of the materials. On this basis, it was decided to modify the Navy flame resistance test for thermosetting plastics to render it applicable to the determination of the toxic, gases evolved when this test was employed. A wide variety of materials was tested, both molded and laminated, to cover the types commonly used by the Navy in electrical applications. Toxicity determinations were conducted at the Bureau of Mines Central Experiment Station, Pittsburgh, Pa. Parallel tests, to determine the flame resistance of the materials, were conducted at the Material Laboratory, U. S. Navy Yard, New York, N. Y."

Oct 1, 1947

By L. C. IlsLey, E. J. Gleim

The extensive use of pulverized coal for fuel in industrial plants has brought to the front again a question that heretofore has been considered only a mining problem, namely, " Can coal dust be ignited by an electric arc ? " If it can be so imited, the next logical query is , "under what conditions can such ignition occur ? " In view of the new problems relating to pulverized coal installations , and because of occasional mine disasters attributed to ignition of coal dust by electric arcs , it seems advisable to review the work done by Thornton and Bowden with electric flashes in coal dust , and to report two preliminary investigations conducted by the Bureau of Mines .

Jun 1, 1922

By Anthony J. Miscoe, William M. McKewan, Richard C. Wang

The behavior of wire ropes used in hoisting is not well understood. In an effort to improve this understanding, the structure of round-strand wire ropes was analyzed. This report provides a generalized mathematical model that completely describes the geometry of the wires. It consists of two sets of vector equations and is valid for any round-strand wire rope. One set of equations is used to trace the paths of wires that have the form of a single helix; the other is used for the paths of double helical wires. The specific model for a 33-mm 6×19 Seale, independent wire rope core (IWRC), right regular lay wire rope was presented as an example. The paths and the geometric properties of the wires, which include the path length per lay of strand, the curvature, and the torsion, were determined from this model. The effects of strain deformation were analyzed, resulting in a system of equations for determining the structural parameters of the deformed rope. In future work, the model could be used to analyze wire ropes of different constructions so that a more scientifically based understanding of rope behavior can be established.

Jan 9, 1998

Coal research and technologic work by the Bureau of Mines covers a broad program of investigation aimed at conservation and utilization of this important natural resource. Conservation is served by a constant search for higher efficiencies in mining, preparation, and use. Increased utilization is sought through various projects that probe new ways to use coal and expand existing coal markets. This report, the twenty-eighth in the series,3 gives the highlights of Bureau of Mines coal research and technologic work in 1963. The scope and complexity of the program makes it virtually impossible to report all progress on every project, even tor a 12-month period. Full insight into each project can be gained only through intensive review of basic objectives, past accomplishments, and current status of the work. Details of the work are given in numerous publications issued by the Bureau and its laboratories and centers located throughout the country.

Jan 1, 1964

By Laxman S. Sundae

The Bureau of Mines designed, fabricated, and is using an in-seam tester (1ST) for in situ determination of coal cutting forces. This re-port describes the results of field tests conducted in the Pocahontas No. 3 and Upper Freeport seams to obtain peak and mean cutting forces during coal cutting with several bit geometries, including radial and point attack bits currently used on drum-type machines. Comparisons were also made between new and worn bits, and using data obtained from a Bureau-modified chisel bit. The test results show that longwall plough cutting (horizontal cuts) in bony coal bands (shale) requires >3 times the cutting force for the same cuts in a vertical direction. When no bony coal is present, the cutting forces required to make horizontal and vertical cuts are equal. Worn bits require 4 to 5 times more cutting and normal force than new or undamaged bits. Normal force increased drastically for the worn chisel bit. Peak force encountered in making independent cuts was found to be ~3 times higher than that required to make interactive cuts using a spacing-to-depth-of-cut ratio of 2. Both rake and clearance angles were found to have a significant effect on normal and cutting force.

Jan 1, 1986

By Michael S. Miller

The Carson-Iceberg RARE II study area, consisting o; 209,990 acres (134,983 ha), is on the crest of the Sierra Nevada in California, about 35 mi (56 km) south of Lake Tahoe. The area is divided into four parts: C4-986; C5-986; and B5-986, north and south portions. No mineral production has been recorded for the area. However, gold, silver, and tungsten resources and potential for additional resources have been estimated for the area and just north of area C4-986.

Jan 1, 1981

By Donald E. Redmon

This Bureau of Mines report reviews injury experience in the nonmetallic mineral industries (except stone and coal) for 1968-69. For each of the years, 23 tables summarize disabling work injuries by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

Coal research and technologic work by the Bureau of Mines covers a broad program of investigation aimed at conservation and utilization of this important natural resource. Conservation is served by a constant search for higher efficiencies in mining, preparation, and use. Increased utilization is sought through various projects that probe new ways to use coal and expand existing coal markets. This report, the twenty-eighth in the series,3 gives the highlights of Bureau of Mines coal research and technologic work in 1963. The scope and complexity of the program makes it virtually impossible to report all progress on every project, even tor a 12-month period. Full insight into each project can be gained only through intensive review of basic objectives, past accomplishments, and current status of the work. Details of the work are given in numerous publications issued by the Bureau and its laboratories and centers located throughout the country.

Jan 1, 1964

By Franklin H. Persse

The Bureau of Mines estimated reclamation costs for 13 surface coal mines in nine States west of the Missisisppi River. With the exception of the Pacific Coast coal province, at least one mine in each of the western coal provinces was studied. Cost estimates were, made using standard estimating procedures from data obtained from company records, interviews with industry personnel, and onsite observations. Estimated costs are presented in four categories which represent the four phases of mined-land reclamation: (1) Design, engineering, and overhead; (2) bond and permit fees; (3) backfilling and grading; and (4) revegetation. Estimated costs as of the first quarter of 1976 are expressed as averages and ranges in terms of per acre, per ton of coal produced, and per million Btu. Total reclamation costs ranged from $860 to $7,200 per acre, from 6 to 84 cents per ton, and from 4 to 35.3 mills per million Btu. A mine in the Northern Great Plains coal province (Region D) showed the highest per acre cost whereas mines in part of the western region of the Interior coal province (Region A) experienced the greatest per ton and per million Btu cost. The high cost of reclamation in the Western United States is reflected in the backfill in and grading category, particularly in the cost of topsoil removal and subsequent replacement as required by individual State reclamation regulations.

Jan 1, 1977

By Susan Brink

The U.S. Bureau of Mines is investigating the potential of in situ leach mining a variety of Cu, Mn, and Au-Ag ores. Geologic characterization of ore samples from laboratory leaching experiments is conducted both prior to and after leaching to assess the effects of leaching on the chemistry, mineralogy, and texture of the rocks. The identification and chemical compositions of ore, gangue, and reaction products are determined by a combination of techniques such as reflected and transmitted light microscopy, X-ray diffraction, electron diffraction, electron microprobe analysis, and backscattered electron imaging with scanning electron microscopy. The distribution of the desired metal in various mineral phases can be illustrated using elemental X-ray maps. The potential of reactive gangue minerals to rob Cu from leach solutions is investigated with the aid of transmission electron microscopy. Porosity and permeability are measured to determine how effectively the host rock can transmit leach solution. Textural relationships between ore, gangue, secondary reaction products, and fluid channelways are determined by petrographic examination and are documented by optical photomicrographs and secondary electron imaging. Representative sample selection is described, and several epoxy impregnation and sample mounting techniques are discussed.

Jan 1, 1991

By George A. Morgan

The 53 countries that constituted Africa in 1991 accounted for a significant portion of total world output of a number of mineral commodities. However, total output for the continent declined for many major mineral commodities produced compared with that of 1990. Also, Africa's share of total world output of these commodities generally declined. (See tables 1 and 2.) The most conspicuous declines were for cobalt and copper owing to mining and metal processing difficulties experienced by the world's two largest cobalt producers, Zaire and Zambia. Phosphate rock output declined primarily owing to a sharp fall in production from Morocco, also a leading world producer. Morocco's state corporation for phosphate production experienced marketing problems, leading to the decline.

Jan 1, 1993

By Magnus Persson

ISO8662-4, “Hand-held portable power tools - Measurement of vibrations at the handle - Part 4: Grinders” is under revision. The new revision shall harmonize ISO 20643 “Mechanical vibration - Hand-held and hand-guided machinery - Principles for evaluation of vibration emission” which, among others, requires measurements in three directions and declared values related to the upper quartile of real-use vibration. To get the most suitable test method, a round robin test was made for evaluation of the two test methods proposed by the ad-hoc group working with this standard revision. Methods Seven laboratories measured the vibration from four grinders of different sizes, with and without autobalancing units. The laboratories come from universities, health & safety laboratories and grinder manufacturers. Two measurement methods are evaluated with respect to repeatability and reproducibility: 1. Grinding on a well-defined mild steel bar with depressed center wheels according to detailed test instructions. The test sequence starts and ends with 10 seconds of running the grinder in the air, when measuring the unbalance contribution to the vibration coming from the unbalance of the grinding wheel. Between these runs the average vibration during 60 seconds of grinding is measured. Three operators do five grinding tests per grinder. 2. Measurements using an aluminum unbalance disc similar to the one defined in ISO8662-4. Each operator runs the grinder four times, between each run the unbalance is moved 180 degrees to avoid variations caused by the play between the test wheel and the spindle. The averaging time is 10 seconds. Each grinder is tested by three operators. Repeatability is the spread within a lab between operators and over short time period for one machine and reproducibility is the spread between laboratories and over longer time periods for one machine. Instrumentation and transducer location are chosen according to ISO8662-4 and circulated test instructions. Results Both the repeatability and reproducibility is poor for the real grinding test, see figure 1. The coefficient of variation for repeatability is approximately 40% higher for the grinding test and the coefficient of reproducibility is 60% higher for the grinding test than for the unbalance disc test.

Jan 6, 2006

By Robert F. Randolph

Real-world levels of attenuation from hearing protection devices are usually much lower than the rated values obtained under near-ideal circumstances. The shortfall is even more extreme for earplugs than it is for earmuffs, primarily because of the complicated process of fitting the plugs within the ear canal. This study examines the use of a commercially-available lubricant for hearing aids to determine whether it would facilitate improved fit and attenuation for earplugs. In this experiment, ten participants inserted earplugs with and without using the lubricant. Average attenuation was assessed with the Real-Ear-Attenuation-at-Threshold (REAT) technique, and showed over 5 dB improvement when the lubricant was used. Participants obtained an 85% mastery rate using the lubricant versus a 50% mastery rate without. These results indicate several possible applications for improved earplug performance in real-world settings where hazardous noise is unavoidable and effective hearing protection is necessary.

Jan 1, 2008

By Lloyd Carpenter

Eighteen elements were determined spectrochemically in vanadium metal and its compounds in the general range of 1 to 1,000 ppm by means of spark-ignited unidirectional arc excitation. The samples were converted to vanadium pentoxide and combined with a mixture of graphite, lithium carbonate, and gallium oxide. For the molybdenum determination, the oxidized samples were mixed with sodium chloride and packed in copper electrodes. Average precision of the method was 15.6 percent relative standard deviation and relative error was 4.4 percent.

Jan 1, 1963

By Verne E. Hooker

Stress relief measurements were made at three underground test sites associated with the Henderson project, American Metal Climax, located in the rugged, mountainous region between Loveland Pass and Berthoud Pass on the Continental Divide in Colorado. Sufficient data were obtained to determine the three-dimensional stress ellipsoid for each site. The measurements were made at hole depths greater than one diameter of the mined opening; thus, calculated stresses are representative of premining in situ conditions. The vertical components of stress are in good agreement with overburden depth including the influence of mountain topography. Horizontal components of stress substantially increase with depth. These components are believed to be influenced by stresses presumably of tectonic origin. The largest measured principal stress was 5,900 psi at a depth of 3.708 feet. The predominant orientation of maximum principal stress for the determinations at greatest depth is in the NW-SE quadrants.

Jan 1, 1972

By G. R. Hopkins

The petroleum-refining industry established a new record in fuel efficiency at refineries in 1936, when 597,000 B. t. u. of heat were required to refine a barrel of crude oil, compared with an average of 615,000 B. t. u. in 1935 (see fig. 1). The principal factor in the "indicated gain in fuel efficiency at refineries in 1936 was an increase in crude runs of 11 percent over 1935. A large part of the heat utilized at refineries is consumed elsewhere than under stills, or in ways quite independent of crude-oil distillation. In other words, as the operating ratio (crude runs divided by capacity) for refineries increases toward the maximum of 100 percent, the fuel requirements show progressively smaller increases and the average E. t. u. consumption per barrel of crude refined declines.

Jan 1, 1938