Search Documents

By F. S. Crawford

Untreated timber in a mine or elsewhere may fail prematurely because it may "rot out before it wears out." If such timber is treated with a satisfactory preservative, decay will be retarded for many years, and it's serviceable life will beg prolonged to several times that usually obtained from untreated timber.4/ Treated timber has many advantages, and although it has been used extensively by railroads and other large consumers of structural timber, the relatively small use in mines seems strange indeed. Timber does not decay if it is kept dry, cool, and well-ventilated or if it is kept constantly wet or sumberged in water. At a mine in Canada the temperature in the upper levels was only 44° F., and the timber did not decay. As operations deepened, however, warmer ground was opened, and, with high humidity, conditions favored timber decay. The life of untreated timber may be only 2 to 3 years under such conditions.

Jan 1, 1951

By J. E. Tiffany

Some of the gases produced by permissible explosives on detonation are poisonous, and the probable hazard involved by the inhalation of carbon monoxide in the past has been evaluated from results of tests in the Bichel Gage. Tests have now been made in the Experimental Coal Mine of the Bureau of Mines at Bruceton, Pa., to determine the composition of the gases obtained under actual mining conditions for the purpose of comparing these, results with those found by the Bichel gage tests. Two permissible explosives were procured for these tests, one that produces a relatively low quantity of poisonous gases in the Bichel gage (24.8 liters per 1-1/2 pounds of explosive) and another that produces a relatively high quantity of poisonous gases (94.6 liters per 1-1/2 pounds). The first of these is designated by the Bureau of Mines as a class A4/ explosive and the other is designated a class B explosive. In comparison with Bichel-gage tests, the shooting of permissible explosives in a coal shot hole resulted in a large reduction in the quantity of carbon monoxide, the principal poisonous gas, which; in the mine tests, was only 22 percent of that found in Bichel-gage tests: The quantity of carbon monoxide from the class B explosive in Bichel-gage tests was 3.8 times larger than that from the class A explosive; in the coalmine tests the ratio was 4:1. The concentrations of carbon monoxide in the mine tests, as determined by analysis of the atmosphere in an enclosed space resulting from shooting 1-1/2-pound and 3-pound charges of the class A explosive, were 0.03 and 0.06 percent, respectively, and the concentrations from 1-1/2-pound and 3-pound charges of the class B explosive were 0.10 and 0.24 percent.

Jan 1, 1950

By Richard J. Mainiero

Traditional techniques for the experimental determination of toxic fumes produced by the detonation of high explosives are not applicable to blasting agents. To detonate properly, blasting agents require confinement, a significant booster, charge diameters of 3 inches (7.5 cm) or greater, and charge lengths greater than two-times the charge diameter. Without these conditions, blasting agents will not detonate at full order, leading to a misrepresentation of the gaseous products. A facility for detonating large, confined charges in a controlled volume has been constructed at the Pittsburgh Research Center’s Experimental Mine. The facility consists of a portion of mine entry (once used for full-scale mine explosion research and demonstrations) enclosed between two explosion proof bulkheads. Total volume of the chamber is 9,666 ft (274 m). The chamber is equipped with an air circulating system and is3 3vented using the mine's airflow. Up to 10-pound (4.5-kg) charges can be detonated in the chamber using a variety of confinements. For a typical test, the blasting agent is confined in a 4-inch (10-cm) schedule 80 steel pipe and initiated by a 3-inch (7.5-cm) diameter, 1-inch (2.5-cm) thick Pentolite booster. This combination of confinement and initiation yields a detonation velocity of about 4,000 m/sec for ANFO. This velocity is in line with that measured for blasting in the field. Twenty four 2-inch thick steel plates are suspended around the pipe bomb to stop shrapnel that would otherwise seriously damage the chamber. Following detonation of an explosive in the chamber, a circulating fan is run for about 10 minutes to uniformly mix the chamber atmosphere. Fumes samples are taken out of the chamber through 1/4-inch (0.6-cm) Teflon or polyethylene2tubes for analysis. The fumes are analyzed using bubblers or Vacutainers to collect samples for analysis by the analytical chemistry lab. The technique described here has been employed to determine the fumes produced by the detonation of a variety of ANFO formulations and commercial explosives. This technique may be developed as a standard test to measure fumes produced by blasting agents or may be used to provide data with which to develop a computer model that will reliably predict the expected fumes production based on chemical composition.

By L. H. Johnson

"INTRODUCTION The Pennsylvania anthracite industry produced 53 million net tons of anthracite during 1945. Fifty-one million tons was prepared for the commercial market (3), 3/ and 2 million tons (consisting of fine sizes) was used for colliery power consumption. Of the number of tons prepared for market, 17 million tons (33 1/3 percent) was prepared by the use of acid mine water treated with lime.Mine water from underground workings is pumped, drained, and stored in huge quantities. The mine-drainage systems in the anthracite region handle over 200 billion gallons of water annually, of which 150 billion gallons is pumped to the surface. More than 69 billion gallons of water is impounded in underground pools (1). Much of this water is employed for breaker use, dust-control installations; hydraulic backfilling, combatting mine fires; and aiding in the transportation of anthracite in gently dipping places where sheet iron is used Roos(4) estimates that 1,100 gallons of mine water is utilized in the preparation of anthracite mined."

Nov 1, 1946

By M. D. Carver

This investigation was undertaken by the Bureau of Nines to determine the effects of impurity levels on the mechanical properties of columbium at low temperatures. High-purity, electron-bombardment-melted columbium was purchased and used as a basis material. Variations in impurity levels were obtained by arc-melting charges containing definite amounts of added impurities. Tensile tests were conducted at low temperatures. Results showed the almost pure basis metal to be ductile at minus 194° C., the lower limit of the range used, Ductility of less pure columbium appeared to depend on interstitial element content. The ductile-to-brittle transition temperature appeared to be raised by increasing carbon content in the range of 50 to 730 parts per million, nitrogen content in the range of 50 to 200 parts per million, or total interstitial element content in the range of 240 to 1,380 parts per million. Some evidence was obtained indicating that decreasing cold work also raised the transition temperature, but recrystallization appeared to have no effect on it. Variations in interstitial element levels appeared to have little or no effect on ultimate strength of columbim in the range of room temperature to minus 194° C, Physical metallurgy studies of massive arc-melted and electron-bombardment- melted columbium were included in the columbium-tantalum research work assigned to the Albany Metallurgy Research Center in fiscal year 1959.

Jan 1, 1961

By Heine Kenworthy

In 1930 the Shenandoah-Dives Mining Co. near Silverton, Colo., put into operation a newly erected, 300-ton selective flotation plant to mill complex ores from its nearby mine. The operation was a steady producer and was enlarged to treat 600 to 800 tons a day. In 1942 the company opened and started milling an area in the mine containing semioxidized ore. The valuable mineral. Content of this ore was considerably higher than in the straight sulfide ore previously handled alone. The mixture of clean sulfide and semi-oxidized ore was difficult to treat; consequently tailing losses, especially with respect to lead, were high. A. few years later, in order to study the possibilities, of obtaining higher recoveries by a modification of the mill flow sheet, a 1,200-pound sample of mill feed, taken over a period of several days by the company, was submitted to the Mississippi Valley Experiment Station for testing. Although this sample proved to contain more than twice as much lead as the average yearly mill feed, the same problem of recovering the oxidized values were present.

Jan 1, 1948

By A. A. Sonnek

A simple, portable helium analyzer was developed primarily for field use. Its utility lies in making preliminary surveys before exact analyses are required. The analyzer is based upon chromatographic principles; that is, separation of gas mixtures resulting from variable retention times of the components with respect to a separation medium (column-packing material). It uses thermistors for sensing detectors, a dry battery as source of power, and a micro-ammeter for indicating helium concentration. The absolute accuracy of the instrument depends upon the recency and care with which the instrument is calibrated with a standard gas. The unknown gas should be analyzed immediately after calibration, and another calibration should be made before another unknown sample is analyzed. The instrument is simple to operate, requiring approximately 15 minutes, after calibration, to determine the helium content of a natural gas sample. Although developed primarily for helium determination, the analyzer possibly can be used for other analyses that can be performed at ambient temperatures.

Jan 1, 1965

By Richard A. Watson, James A. Powell

A seismic system which utilizes in-mine geophones to detect trapped miners has been developed. Tests at the Bureau of Mines Safety Research Mine at Bruceton, Pa., and at two operating mines indicate such a system has a maximum detection range in excess of 1,000 feet. The system is field worthy and portable and requires less than 30 minutes to set up and check. Real-time detection is possible.

Jan 1, 1976

By A. W. Fahrenwald

As an aid to studies of grinding, a batch laboratory classifier and elutriator has been developed at the U. S. Bureau of Mines Metallurgical Field Office at Moscow, Idaho, in cooperation with the University of Idaho. It is designed for use in conjunction with other batch laboratory apparatus, such as ball mills and flotation machines. It is shown in Figure 1. Description and Operation of Batch Laboratory Classifier The classifying column is a cylinder 4 feet 2 inches long, of 5 3/4-inch inside diameter, and terminates at its top in a cone or funnel 18 inches in diameter at the overflow elevation. The pressure chamber is of the same diameter as the classifying column, and has a conical bottom; it is provided with two openings, one in the cylindrical portion through which water is admitted, and the other, a small drain hole, in the apex of the conical bottom. The two compartments are bolted together and communicate with each other through the medium of a constriction plate provided with 3/16-inch holes spaced 1/2 inch apart. Constriction plates having any other percentage of opening may be substituted as the needs demand water is admitted to the compartment below the constriction plate at constant pressure. The volume of eater admitted is controlled with a valve. It should be mentioned that the classifying column at the bottom, just above the constriction plate, is glass.

Jan 1, 1929

By P. D. Tracy, M. W. Von Bernewitz

"IntroductionA study of 256 coal-mine explosions, which occurred during the period 1909-1924 killed 4113 men and injured 570 others, reveals the fact that there are the critical times of day when explosions are most likely to occur, and when corresponding care should be exercised to guard against disaster. Of these 256 explosions, 83 straight as explosions, 89 were straight coal-dust explosions, and 81 were mixed gas and dust explosions, while three were undetermined.It has been determined from the times given in these reports (in several cases no times were given,that the critical period in the morning ranges between 6 and 9 o'clock when 83 explosions took place with a peal. at 7;30 o'clock. Of these 55 were straight gas explosions, the remainder being either coal dust or mixed gas and coal dust explosions. The critical period in the afternoon or early ranges between 3 and 7 o'clock, when 113 explosions took place, with a peak at 6 o'clock. Of these, 87 wore straight coal-dust explosions the remainder being neither gas or mixed gas and coal-dust explosions. Between these morning and evening periods is one which might be called the noon period - that is, from 11m to 7. p. m. - when 26 explosions occurred while some of these were normal type of explosions - that is, as to causes - others were of unusual cause and character, and. are discussed later. A number of explosions (29 in all) took place during mid-afternoon, late at night, and early in the morning - that is, after midnight."

Sep 1, 1924

By Irving Hartmann

When permissible explosives are used in coal mines according to the procedure recommended by the Bureau of Mines they are relatively safe, and no mine explosions are known to have resulted from this type of blasting. However, unsafe blasting practices - the use of nonpermissible explosives or the improper use of permissible explosives - have caused many serious disasters. In fact, such unsafe practices constitute the third most important cause (exceeded only by electricity and the use of open lights and smoking) of coal-mine explosions in the United States. During 1929-1947, inclusive, 81 explosions, resulting in 475 fatalities, were ascribed to unsafe blasting. The hazards of black powder, dynamite, and other nonpermissible explosives in coal mines have been recognized for many years, and attention has been called to this in numerous Bureau of Mines publications. Not only can these explosives ignite namable gas-air mixtures readily, but they can also ignite coal dust, as has been illustrated repeatedly in tests and at educational public demonstrations at Bruceton and elsewhere.

Jan 1, 1952

By Welby Courtney

Because of the inherent safety problem associated with the deposition of airborne respirable dust onto the floor and other airway surfaces, the Bureau of Mines investigated the rate of reduction of airborne respirable dust in an airway due to deposition of the particles onto the surfaces of the airway. The effects of relative humidity and air velocity on the deposition rate were examined. It was found that the deposition rate was comparable in magnitude with the Stokes sedimentation rate and that it was independent of relative humidity. However, near the dust source the deposition rate depended significantly upon the air velocity, with such dependence decreasing with increasing distance from the dust source. In addition, the size distribution of the airborne particles was approximately constant along the first 300 ft of the airway, indicating that it was not merely the larger (heavier) particles that were being deposited. These results suggest that deposition, though comparable with the Stokes sedimentation rate in magnitude, does not follow a simple Stokes-type process, and that the process of deposition remains to be explained.

Jan 1, 1986

By Alla D. Mah

The work described in this report is part of a Bureau of Mines research program for obtaining heats of formation of inorganic oxides, carbides, and nitrides by combustion calorimetry. The heats of combustion of molybdenum subnitride (Mo2N) and chromium subnitride (Cr2N) were measured. The data were combined with previous determinations of the heats of formation of molybdenum trioxide and chromium sesquioxide to obtain the heats of formation of the two subnitrides from the elements at 298.15° K. The corresponding free energies of formation were estimated. The heat data were compared with those of nine previously studied nitrides.

Jan 1, 1960

By C. Özgen Karacan

Degasification and methane control in underground coal mining is an important area augmenting conventional ventilation in order to prevent possible fires and explosions due to excessive methane emissions. Coal bed reservoir engineering has been applied for many years to coalbed methane production. In recent years, modeling the flow and draining methane, not only from coal bed itself but also from the overlying strata, have been recognized as important areas of expertise for supplementing underground ventilation. This paper demonstrates the applications of coal bed reservoir engineering and modeling techniques for optimizing and controlling methane emissions in longwall and continuous miner sections. Practical applications and some considerations are presented for reservoir modeling, borehole performances, and face emission predictions for various coal bed and borehole configurations. A section on field reservoir studies and well bore log analyses for methane control are also presented as a complementary way of controlling methane and optimizing ventilation.

Jan 1, 2009

By Sam Friedman

The Bureau of Mines conducted experiments using bench-scale apparatus to explore the effect of large changes in process variables on the yield and composition of the gases produced by passing 800° C steam through a fixed bed of Pittsburgh seam (hvab) coal. The total yield of combustible gases increased throughout the given range for the following variables: Superficial steam velocity increasing from 0.02 to 0.12 fps, pressure increasing from 1,000 to 6,000 psig, residence time increasing from 0 to 60 minutes, and temperature increasing from 800° to 900° C; however, a greater increase in the yield of hydrogen in comparison with the increase in yield of methane reduced the gross heating value of the gas to around 470 Btu per scf at conditions giving the maximum yield. Pressures of 1,000, 3,000, and 6,000 psig at 0.09 fps steam velocity, 800° C, and 60 minutes residence time, respectively, produced methane yields of 20, 24, and 22 percent, based on maf coal, with the gross heating value of the CO2-free gas decreasing from 552 to 520 and to 470 Btu per scf. Methane concentrations in the CO2-free gas were 26, 22, and 14 percent, respectively. Based on the gross heating value of the coal, the percentage of the heating value recovered in the gas was 60, 71, and 87 percent, respectively. The use of tungsten sulfide as a catalyst for converting carbon oxides and hydrogen into methane was explored briefly using both a sulfur-free gas rich in methane and a sulfur-bearing synthesis gas (3H2:1CO).

Jan 1, 1968

By Thomas E. Green

A gas volumetric method was developed for determining metallic aluminum at the 0.01-to 0.3-percent level in 100-gram samples of recycled glass. The method is based on the measurement of the change in gas volume produced by the reaction 2 Al + 2 NaOH + 2 H2O ? 2 NaAl02 + 3 H2 using a simple apparatus assembled from readily available glassware. Apart from sampling errors, the precision of the method is within ±5 percent. A minor modification of the apparatus would extend the method to larger samples or samples of higher metallic aluminum content. Metallic iron and metallic zinc do not interfere at the concentrations found in recycled glass recovered from incinerator residues.

Jan 1, 1971

By B. K. Cantrell, K. L. Rubow

"The US Bureau of Mines and the University of Minnesota have developed design and performance criteria for a personal diesel exhaust aerosol sampler for underground coal mines. These are based on the premise that size can be used to separate diesel exhaust aerosol, which is mostly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. The sampler has three stages: a respirable aerosol preclassifier, a 0.8-um aerodynamic diameter inertial impactor to collect mineral dust and a final filter to collect the diesel aerosol. Using a sample flow rate of 2 L/min and gravimetric analysis to within 0.1 mg, the measure sub-0.8 um diesel aerosol has an a-priori limit of detection of 0.3 mg/m3.A miner working in an underground coal mine with diesel equipment is exposed to a wide array of pollutants from the diesel exhaust. These include CO, CO2. NO, NO2, SO2, diesel exhaust aerosol, and a variety of hydrocarbon compounds. A quantitative definition of the health risk resulting from these exposures remains elusive. During the past several years, though, progress has been made in defining the problem.Results from epidemiological studies by Garshick et al. (1988 ), animal inhalation studies by Mauderly eta). (1986), Iwai et al. (1986), and Brightwell et al. (1986) and in vitro studies by Lewtas et al. (1986) have provided sufficient data for the National Institute of Occupational Safety and Health (NOSH) to recommend that ""whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration"" (NIOSH, 1988). NIOSH further stated that ""though the excess risk of cancer in diesel-exhaust-exposed workers has not been quantitatively estimated, it is logical to assume that reduction in exposure to diesel exhaust in the workplace would reduce the excess risk.""The Mine Safety and Health Administration (MSHA) has also been directed by an advisory committee to establish a diesel exhaust aerosol standard and to establish regulations to minimize exposure to diesel pollutants in underground coal mines (MSHA,1988). Both reports point out the need for development of measurement techniques for respirable diesel aerosol.In the past four years, the US Bureau of Mines (Cantrell,1987 and Cantrell, et al. 1987), in cooperation with Marple, et al. (1986), at the University of Minnesota's Particle TechnologyLaboratory (PTL), have studied the use of size-selective sampling techniques to measure the mass concentration of diesel aerosol in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler for use in underground coal mines.These criteria are based on the premise that size-selectivesampling techniques,can be used to separate diesel exhaust aerosol, which is predominantly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. In addition to the performance criteria, this paper discusses the laboratory and field test data used to develop the criteria."

Mar 1, 1992

By Judith L. Bolis

The Bureau of Mines estimated the potential availability of iron ore from 129 domestic and foreign mines and deposits in 25 market economy countries. The availability of four products on a total and regional basis was determined from demonstrated resources of 75.3 billion It. From the resources evaluated there are a total of 18.6 billion It of sinter fines, 4.9 billion It of lump ore, 14.7 billion It of pellets, and 820 MMlt of pellet feed potentially available at a 15-pct DCFROR, f.o.b. port. On a regional basis, at or below a total cost of $0.26 per iron unit there are 1.7 billion It, 2.8 billion It, and 186 MMlt of sinter fines potentially available from Brazil, Australia, and Africa, respectively. There are 825 MMlt of lump ore from Brazil and 1.4 billion It from Australia potentially available at or below a total cost of $0.24 per iron unit. There are 2.1 billion It of pellets potentially available from the United States at or below a total cost of $0.80 per iron unit, while 442 MMlt are potentially available in Brazil at or below $0.38 per iron unit. South America has 208 MMlt of pellet feed potentially available at or below a total cost of $0.28 per iron unit. While the resources of iron ore are more than adequate to satisfy demand, the future of the iron ore industry is very dependent upon changes in the world economy, and on the domestic scene, changes in the domestic steel industry and steel imports.

Jan 1, 1987

By John W. Frey

This paper presents one of a series of digests of foreign mining legis- lation and court decisions which is being prepared in advance of a general re- port relative to the rights of American citizens to explore for minerals and to own and operate mines in various foreign countries. This interpretation of the laws of Portugal, prepared from the best available information in Washington, has been slightly amplified in accordance with suggestions trans- mitted through the courtesy of the Department of State by Fred Morris Dearing, American Minister at Lisbon.

Nov 1, 1929

By E. D. Gardner

A custom gold and silver plant is one that treats ores for a fee. Usually such plants are located in mining districts and treat local ores. Ores of milling grade generally can stand only moderate transportation charges. These plants are scattered throughout the West. Most plants now doing a custom business originally were built by mining companies to handle ores from their own mires. As excess mill capacity became available ores from neighboring properties were treated, vainly as an accommodation. Later, as their own ore bodies became depleted, the mills were operated entirely on a custom basis. A few plants pull ore from their own mines only when the supply of custom ore is insufficient to keep the mill operating. Some of the present custom plants were built for custom work alone. Although built originally to treat the ores of the Golden Cycle mine, the Golden Cycle plant at Colorado Springs, Colo., soon became a custom mill and has been operating successfully for many years. It is the largest gold mill in the Western States and. treats Cripple Creek ores, from which most of its tonnage still comes. The plant is equipped to treat a great variety of ores and receives shipments from a wide area. It competes with smelters in Colorado, as it has a roasting plant to prepare sulphide concentrates for treatment in its cyanide plant. Most custom mills, however, are not adapted for more than one or two kinds of ore. Gold occurs in its ores both in the metallic state (free) and locked up in sulphides. It also occurs in a few places, notably at Cripple Creek and a few other Colorado districts, as tellurides. Mien the gold occurs in the native state, the ores is said to be free-milling and can be recovered by amalgamation. Usually, however, some subsidiary treatment is required to make a satisfactory extraction. Amalgamation generally was followed by tabling in the earlier mills; at present, flotation has replaced tables at many places. As depth is reached in raining and the workings extend below the oxidized zone the character of the ore usually changes, or, as the miners say, "it gets base". Since the advent of flotation, the average recovery of gold in base ores has been improved-greatly. Cyanidation is applied to some types of both gold and silver ores. The recovery by cyanidation is in general considerably higher than by other methods in vogue and in addition has the advantage of making a finished product which can be sold directly to the mist, thus obviating smelting charges on concentrate and discounts

Jan 1, 1935