Search Documents

By Walter D. Holland

LFE Environmental performed an Industrial Hygiene survey of the Paraho Oil Shale Mining and Processing facility in Anvil Points near Rifle, Colorado, on August 6 and 7, 1975. This survey consisted of an investigation of the underground operations for diesel emission contaminants and of the above ground work areas for all inhalation contaminants other than silica dust. Samples were collected to investigate the following contaminants: respirable dust, total dust, NO2, NO, H2SO4, formaldehyde, CO2, S02 and CO. None of the determinations of contaminants in the underground operations indicate air concentrations exceeding their standards. The results for the samples collected above ground indicate only one operation where the employee's exposure exceeds the standards. It is a welding operation where the standards for total dust and lead are exceeded. Since the survey the employer has installed an exhaust ventilation system which has significantly reduced the welder's exposure.

Jan 1, 1976

By Donald P. Mickelsen

The raining and quarrying trends data shown in this report were reported to the U.S. Bureau of Mines (USBM) by mining and quarrying companies on the Mine Information Supplement survey, as well as by mineral producers on 58 annual USBM production and consumption surveys covering 59 nonfuel mineral commodities. The 1993 data presented in the tables of this chapter, were processed for the first time using the USBM Automated Mineral Information System. Domestic mining of nonfuel mineral materials totaled 3.7 billion metric tons in 1993, including 2.2 billion tons of crude ore nun& or quarried and 1.5 billion tons of mine waste and ore from development. This \vas an overall increase of 11% over that of 1992. These data do not include construction sand and gravel which until 1993 has been surveyed biennially. Starting in 1994, construction sand and gravel and the stones, which were also surveyed biennially, will be surveyed annually.

Jan 1, 1993

To provide a simple means for rapidly checking methane concentrations at working faces in coal mines while remaining under permanently supported roof. The Approach: A light telescopic probe, through which a gas sample can be pumped Into a methanometer, has been developed. See Figure 1 [ ] How It Works: The telescopic probe consists of sections of small stainless steel tubing encased in sections of lightweight fiberglass tubing. When fully extended the probe is almost 19 ft. long; fully closed it is approximately 5-1/2 feet long. It can be used In either of these positions as well as at intermediate extensions. An approved methanometer is clamped to the probe by a support bracket.

Jan 1, 1975

By F. W. Lane

Some months ago the Bureau of Mines began research of a fundamental character on sulphur in petroleum. In the course of this work, the usual qualitative test for sulphur in organic compounds1 was applied to certain oils that were believed to contain approximately 0.5 percent sulphur. No sulphur was found, and, as a check on the qualitative test, the oils were subjected to quantitative determination of this element by the oxygen-bomb method.2 The sulphur content of the oils ranged from 0.10 per cent to 0.50 per cent. This experience led to further trial of the qualitative test for organic sulphur, both on the oils mentioned above, and on common sulphur-containing organic substances. No difficulty was experienced in detecting the element in the latter, but with the petroleum oils the test, as usually performed, could not be relied upon to detect less than 0.60 per cent of sulphur consistently. The use of mechanically polished pure sheet copper for the detection of free sulphur, hydrogen sulphide, and perhaps other sulphur compounds has been recommended.3

Jan 1, 1927

By H. K. Kutter

The pressure pulse generated by an underwater spark \vas investigated in relation to its potential use for rock fragmentation. The study established (1) the relation between the peak discharge current and the peak wave pressure; (2) the relationships among the peak wave pressure, the discharge voltage, and the spark gap width; (3) the type and pulse duration of the generated wave; (4) the percentage of energy transmitted in the spark as a function of spark gap width and discharge voltage; and (5) the percentage of energy converted into the pressure wave as a function of gap width and discharge voltage. Spark-generated fractures were studied in two-and three-dimensional rock and plastic specimens. The laboratory results indicated that the pressure pulse generated by an underwater spark is a potential practical tool for rock fragmentation. The paper contains an appendix describing the capacitive pressure gage specially developed for the laboratory tests.

Jan 1, 1969

By James P. Ulery

A Bureau of Mines geologic study of Pennsylvanian and Permian coalbeds in southwestern Pennsylvania was undertaken to determine the effects of coalbed geology and petrology on in situ coalbed gas contents. Data were obtained from 18 coreholes from parts of four 7.5 ' quadrangles in southwestern Washington and northwestern Greene Counties, and from a single corehole in Westmoreland County. A total of 88 samples from 24 coalbeds were collected for direct-method testing to determine gas content. The samples were also analyzed for petrographic composition, chemical composition, and vitrinite reflectance values. Corehole information was used to generate isopach maps and geologic cross sections useful in data interpretation. Results of the investigation show that coalbed gas content is related to vitrinite reflectance, but not to petrographic composition. Gas contents are also influenced by other geologic factors such as roof rock lithology and competency, and location with respect to local fold structure.

Jan 1, 1989

By Elaine Cullen, Launa Mallett, Mike Jenkins, C. M. K. Boldt, Thomas Camm

The material in this Information Circular was presented at the National Institute for Occupational Safety and Health’s (NIOSH) open-industry briefing held during the 2004 Northwest Mining Association conference in Spokane, WA. The open-industry briefing discussed results of recently completed and on-going mine safety- and health-related research conducted at NIOSH’s Spokane and Pittsburgh Research Laboratories on the human side of mining—the miner. The first paper sets the stage for what mining has achieved and what we mean by “getting to zero.” The second paper, “Help Experienced Miners Become Great On-the-Job Trainers,” distinguishes between experienced miners and trainers. This paper provides some key concepts for turning great miners into great trainers. “The Power of Story-Telling in Getting Through to Miners” explains the history and importance of stories in the culture and training of miners. Finally, “Understanding Self in Stressful Working Environments,” describes the personal and social aspects of the working environment, much of which parallels familial theories. The downward trend of deaths in U.S. mining has been remarkable. The number of miners killed or injured each year has decreased steadily over the past 100 years. Some charts show these trends overlain with important events such as World War II and the Mine Safety and Health Act. However, this downward trend in mining fatalities has flattened out. How can you get to zero accidents? Do you concentrate on technological advances and equipment maintenance to avoid malfunctions? Do you concentrate on developing work processes and organizational structures that minimize risk? Do you combine them and take a systems approach that links one to the other with an evaluative loop? Safety efforts in mining have used all of these approaches. What more can we do to get to zero? Getting to zero will require two objectives: A clear and unshakeable belief that it can be done and attention to the human side of mining. Getting to zero is not a new idea; it has been used by mine companies and safety professionals for years as the safety goal. But getting to zero is not so much a physical goal as it is a belief that there are no insurmountable barriers to achieving the goal.

Jan 3, 2006

By Daniel R. Babich, Jeffrey R. Vipperman, Eric R. Bauer

Prolonged exposure to loud noise can cause permanent damage to the auditory nerve and/or its sensory components. Despite regulations and efforts by government and industry to reduce noise-induced hearing loss (NIHL), it is still a problem in the U.S. coal mining industry. The Mine Safety and Health Administration noise standard (30 CFR3 62), which was enacted in September 2000, is aimed at reducing NIHL in the mining industry. To address NIHL in various aspects of coal mining and provide the necessary information to effectively implement control technologies, the National Institute for Occupational Safety and Health conducted a cross-sectional survey of noise sources and worker noise exposures. Noise surveys consisting of full-shift worker noise exposure (dose) determination, time-motion studies (task observations), and equipment and/or area noise profiling were completed in 8 underground coal mines, 10 surface coal mines, and 8 coal preparation plants. The studies revealed that more than 40% of all workers monitored were subject to noise exposures above 90 dBA TWA8. A summary of these studies is presented, their application to administrative and engineering controls is discussed, and exposure reduction methods are reviewed.

Jan 12, 2006

By P. H. Floyd

Laboratory test work has shown that the Germania ferberite-scheelite ore can be concentrated to an acceptable grade. A ferberite concentrate assaying 66.9 percent tungstic oxide was made, with a recovery of 75.4 percent. A second concentrate of ferberite and scheelite was made assaying 54.2 percent tungstic oxide. Final beneficiation of combined rougher gravity concentrates was accomplished by roasting, magnetic separation, sulfide flotation, and retabling, to give a final ferberite-scheelite concentrate of 66.2 percent tungstic oxide, with a 91.1-percent recovery. INTRODUCTION This presentation covers the results of laboratory beneficiation tests conducted on tungsten ore from the Germania Consolidated Mines, Inc., by the Bureau of Mines Mineral Dressing Section, Northwest Electrodevelopment Laboratory, Albany, Oreg. This mining property is near Fruitland, on the southern edge of the Spokane Indian Reservation, Stevens County, Wash. The Germania district produced tungsten concentrates before and after World War I; interest is being renewed in the district because of the metal shortage.

Jan 1, 1954

By A. E. Nagel, J. E. Carpetta, M. G. Zabetakis, T. D. Moore

The method of moving averages was found useful in assessing the nature of methane emission in coal mines. Emission rates were influenced markedly by the presence of abandoned oil and gas wells in the vicinity of the mine. Such wells appeared to increase the flow rate of methane into the mine by a factor of 2 to 30 in an active mine in the Pittsburgh coal seam.

Jan 1, 1972

By R. V. Ramani, A. S. C. Owili-eger

List of Numbers

Jan 1, 1974

By J. Grumer

Nine dust and gaseous inhibitors of propagating coal dust-air flames (lean, stoichiometric, and rich) were evaluated in a newly developed 15-cm-id, 3.6-meter-long instrumented flame duct, under conditions such that wall quenching was virtually absent and the dust concentration was temporally and spacially uniform to within about t5 percent. Listed roughly in order of increasing efficiency, the inhibitors evaluated were rock dust (calcium carbonate), powdered oyster shells (calcium carbonate), Halon 1301 (trifluorobromomethane), Halon 1211 (difluorochlorobromomethane), sodium chloride, Super-K (potassium chloride), regular-grade fire extinguishant powder (sodium bicarbonate), Purple-K (potassium bicarbonate), and Monnex (potassium bicarbonate combined with urea). Experiments were extended to clouds containing 1 and 2 volume-percent of methane. The inhibition of lean, stoichiometric, and rich methane-air flames without coal dust was also examined in a few instances; results agreed with those obtained for coal dust-air flames.

Jan 1, 1971

By A. W. Khair, M. Ahmad

"Bit wear has been proven to have a significant effect on respirable dust generation in coal cutting system. The mechanism of bit wear can be adhesion, abrasion. oxidation, or diffusion. depending on cutting conditions. This paper presents a portion of an extensive ongoing series of studies to better understand the principles of bit wear and dust generation. Used bits collected from underground coal mines were analyzed to identify the basic principle of bit wear in coal and rock cutting. Distribution of weight loss and conical height loss of worn bits were studied and bit wear was divided into four stages according to weight loss. Utilizing these worn bits, Laboratory experiments have been carried out to study the effects of bit wear on coal cutting system and respirable dust generation. An Automated Rotary Coal Cutting Simulator was use to perform the experiments. Acoustic emission monitoring is applied to study the effect of bit wear on fracture formation and dust generation. INTRODUCTIONContinuous miners were introduced in the 1950’s and became the major equipment in underground coal production. Now the larger production in the coal industry has increased the demand for continuous miners and their use. It is well known that serious dust problem is also introduced with the use of continuous miners, especially with recent increase in productivity. On the other hand, legal restrictions are made ·more strict by the Mine Health & Safety Administration for the respirable dust generated by the continuous miners to prevent coal workers from incidence of pneumoconiosis. The incidence of pneumoconiosis depends on dust concentration, exposure time, and physical properties of dust. Of them, dust concentration is the best parameter for the assessment of the risk of pneumoconiosis. Although a lot of research work has been done to reduce dust concentration substantially, some areas are still required further investigation to meet the strict regulations. One of the areas is about bit wear and dust generation. In this area, the principles of bit wear and effect of bit wear on dust generation are major concerns."

Mar 1, 1992

By Franxis Church Lincoln

"INTRODUCTION During September 1944, the Bureau of Mines undertook a program of investigation and limited exploratory drilling at the Last Chance mine, near the village of Arthur in Grant County, Wisconsin, as part of a general investigation of the zinc-producing area of southwestern Wisconsin when every effort was being made to increase the production of metals important to the Nation's war program.The Bureau's attention was directed, to the Last Chance mine when the operators discovered high percentages of zinc in an exploratory churn drill hole a short distance southeast of the mine. The ore was found in the Trenton Limestone, which underlies the ore horizon then being mined. To determine whether this discovery was important, and to demonstrate the possible extension of the ore the Bureau of Mines drilled five additional holes in the vicinity of the discovery.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Nines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report."

Mar 1, 1947

By R. K. Koch

The Bureau of Mines produced several series of titanium castings in order to investigate the feasibility of producing commercial-grade titanium castings in bentonite-bonded olivine or zircon sand molds. The use of these molds for titanium casting was investigated as a possible alternative to the industrially used rammed graphite process. Parameters investigated were mold mixtures, mulling, gating, venting, drying, and mold washing. The investigators found that castings with superior ductility and fatigue life, compared with rammed graphite castings, could be made by fume-free pro-cesses in molds bonded by western bentonite, using either olivine or zircon sand. Zircon molds were satisfactory for both light-and heavy-sectioned castings. However, olivine molds were suitable only for light-sectioned castings because the mold-metal reaction became excessive during the pouring of heavy-sectioned castings.

Jan 1, 1981

By William K. Tolley

The U.S. Bureau of Mines (USBM) is investigating hydrometallurgical processing techniques to recycle metals from semiconductors and other advanced materials. Cadmium and tellurium were recovered from mixed CdTe/CdS scrap produced in the manufacture of thin-film photovoltaic devices. Selective cadmium dissolution was achieved using oxygen-pressure leaching in dilute sulfuric acid. Leaching the scrap for 90 min at 110° C in 2.2NH2S04 under 400 psig 02 yielded 97% Cd extraction; however, cadmium content of the residue ranged between 4% and 7%. Soluble iron was added to the lixiviant to catalyze oxidation of the CdS component. Tellurium and sulfur remained in the leach residue primarily in the elemental form. The iron and tellurium were removed from the cadmium-rich leach liquor by adjusting the pH to 5.3. The cadmium was recovered as cadmium sulfate crystals by evaporating the solution. Alternative leaching and purification schemes are discussed.

Jan 1, 2010

By R. Agarwal

The in-situ stress field was determined, using the overcoring technique, at two underground sites at the Pea Ridge Mine, Sullivan, Missouri. At one of the sites in magnetite, the three dimensional stress field showed the largest principal stress to be compressive (-4564 psi), nearly horizontal and closely parallel to the strike of the orebody. The smallest principal stress was also compressive (-2047 psi) and nearly vertical. Considerable difficulty was experienced in drilling porphyry rock at the second test site in the host rock. Only one hole was drilled at this site. The secondary principal stresses obtained in the porphyry are -9464 and -4945 psi, respectively. The-test site in magnetite is located at a depth of 2505 feet whereas the site in porphyry rock is at 2475 feet. The vertical stresses: due to overburden loading at these sites are -3590 and -2782 psi, respectively. Field determined values of the vertical stress are -2207 and -5098 psi, respectively. The variance; between the two sets of values is most likely attributable to the orebody formation and the differences in the modulii of the host rock and the orebody.

Jan 1, 1977

By W. P. Diamond, A. C. Smith, J. A. Organiscak, T. P. Mucho

The U.S. Bureau of Mines conducted a worldwide literature review of bleederless ventilation practices to evaluate their use as a spontaneous combustion control measure in U.S. coal mines. Factors that must be taken into account in the design and use of these systems include seal construction, the use of ventilation control devices, the use of methane-drainage systems in gassy mines, and the ground control plan. Monitoring for the detection of spontaneous combustion and the control of methane when methane-drainage techniques are employed is critical to the successful use of a bleederless ventilation system. This report describes the types of ventilation systems used throughout the world and the spontaneous combustion risks associated with these systems. Methane-drainage systems used in conjunction with bleederless ventilation systems are discussed. Ground control considerations such as pillar design, entry stability, and seal usage are reviewed. Monitoring systems for spontaneous combustion detection, methane-drainage control, and behind seals are examined. Finally, methods for evaluating the spontaneous combustion hazard of a mining operation to determine when the use of a bleederless ventilation system is warranted are reviewed.

Jan 1, 1994

By Charles L. Kimbell

Tables 16 through 19 continue the series of providing the world merchant fleet distribution by type of vessel and the ranking of the major fleets by country of registry. Table 20 this year provides a summary of the world's liquid gas carrier fleet. These vessels are included in the totals given for the world's tanker fleet, but gives a breakdown demonstrating the growth of the importance of natural gas in the world's energy commodity consumption. Panama and Suez Canals Tables 21 and 22 provide the latest available information on the transit of mineral commodities through the Panama Canal, by number of vessels, direction, and the commodities transported. Although the number of vessels transiting the Panama Canal dropped slightly (0.5%) between 1989 and 1990, the total amount of cargo moved rose by 3.6% and the amount of mineral commodities moved rose by 7.2%.

Jan 1, 1993

By Richard Havens

A flotation procedure was devised by the Federal Bureau of Mines for beneficiating Mount Wheeler, Nev., beryllium ores that contain the beryllium minerals bertrandite and phenacite in a complex association with calcite, fluorspar, mica, quartz, and other accessory minerals, The method also has proven to be effective in trials on ore from the Lake George, Colo., area. Samples used in most of the research ranged from 0.49 to 0.73 percent BeO. Beryllium mineralization varied from two-thirds bertrandite to all phenacite. An unusually high grade sample containing 5 percent BeO as phenacite was floated on a batch basis to prepare concentrate for utilization studies. The beryllium minerals were floated from undeslimed pulps at natural pH using sodium fluoride and sodium hexametaphosphate (HMP), as modifiers, and a fatty acid-fuel oil combination as the collector. Key factors were the use of a minimum of about 4 pounds of sodium fluoride and between 2 and 4 pounds of HMP per ton of ore. Efficacy of the HMP was related to the grind, mineralogical composition, corollary reagents, and type and time of conditioning. Addition of the fluoride, HMP, and collector in that order, followed by appropriate conditioning after each addition, was essential for satisfactory flotation.

Jan 1, 1961