Search Documents

By C. W. Owings

When explosions have occurred in mines where rock dust has been used to some extent, generally to a very limited extent, the press has immediately characterized those mines as "rock-dusted." To persons familiar with the method of rock-dusting, it is apparent that if rock-dusting is done properly, if all mine surfaces are rock-dusted to within at least 40 feet of the faces of rooms and entries, and if the incombustible content of the dust is more than 65 per cent, there is little likelihood that an explosion of coal-dust will occur. The report that an explosion has occurred in a "rock-dusted" mine immediately conveys to the mind of the alert safety advocate the information that the mine is inadequately rock-dusted or that either dust sampling of the rock-dusted surfaces has not been done or, if done, the mine has not been redusted with sufficient promptness. Rules for Collection of Samples Collection of dust samples is by no means intricate, but a few simple rules must be kept in mind if the results are to be dependable. A sample must represent the true average conditions of the dust in the section or zone in which it is taken, and therefore 'the point at which the sample is to be collected must be selected with care. During an explosion much if not all of the dust on the ribs, roof, timber, and road in the affected region is blown into the air; the sample, therefore, should contain all loose dust and material on: the surfaces to a depth of about 1 inch, if that amount is present. If there is considerable sand locally along the track, care must be taken not to include enough of this material to vitiate the sale and distort the results; however, if the sand is distributed throughout the region being sampled it should be included. Dust should not be collected from recesses in the ribs, such as hitches cut for timber, as the character of the dust in such places is often different from that on the ribs proper. Samples should not be collected at points where the dusting machine has been loaded or at a point where the machine has stopped and discharged for a longer period than at other points on the entry or in the rooms. In short, the sample must represent AVERAGE CONDITIONS, and if there is any doubt as to the character of the dust it is far better to have too much combustible matter than too much incombustible matter in the sample, as it is best to err on the side of safety if it is necessary to err.

Jan 1, 1929

By Dennis R. Dolinar, Lewis A. Martin

Cable bolt technology used by the U.S. coal industry was developed to a large extent in the 1990s. Today, these cable systems include both cable bolts and cable trusses to provide supplemental and secondary support in gate roads. This cable technology is significantly different than the cable systems in use in either U.S. hard-rock mines or Australian coal mines. Development of this technology was initiated and spurred by research efforts of the U.S. Bureau of Mines, and has continued under the health and safety programs of the National Institute for Occupational Safety and Health (NIOSH). It was also followed up by work of roof support manufacturers to create an essentially new support system. In this paper, the important support characteristics of both cable bolts and cable trusses are discussed. The design of cable systems and the basis for that design for tailgate and headgate situations are reviewed and explained. Case histories are presented on the application of these support systems based on experience gained at a number of in situ test sites.

Jan 10, 2000

By M. L. Whisman

Radiotracer techniques were developed for stoichiometric studies of photochemical reactions associated with atmospheric smog formation. Stock blends of separate hydrocarbon and oxygenated compounds were prepared and calibrated. 14C-labeled reactants and products in reaction systems involving hydrocarbons and nitrogen oxides at the ppm level were analyzed for qualitative and quantitative data. Precision and accuracy of these methods developed by the Bureau were determined by replication and statistical treatment of data, and these methods are described.

Jan 1, 1969

By R. C. Gabler

Laboratory tests on a combined nitrogen roast--two-stage leach--electro-winning approach show promise as a possible process for recovering copper, sulfur, iron oxide, and valuable minor metals (gold, silver, and molybdenum) with a minimum impact on the environment. During the nitrogen roast at 800° C, 15 to 20 percent of the sulfur together with a significant fraction of the volatile elements, such as arsenic, bismuth, lead, and zinc, are removed from the chalcopyrite concentrate. The resulting calcine, consisting of 8-chalcopyrite, troilite, and a bornitelike structure, is leached with hydro-chloric acid to remove 70 to 85 percent of the iron. The digenite in the leach residue is dissolved in an oxygen-saturated, spent sulfate electrolyte. Using a graphite 'anode plus sulfur dioxide to reduce interference from ferric iron, copper of 99.99+ purity is electrowon at current efficiencies of 88 to 92 percent and a cell voltage of 0.4 to 0.5 volt. Copper recovery for the overall process is 98 to 99 percent. Sulfur is obtained in the elemental form from the roasting and leaching steps. Iron can be recovered from the hydro-chloric acid leach solution. Gold, silver, and molybdenum are concentrated in the silica residue from the spent electrolyte leach.

Jan 1, 1975

By C. J. Mains

The gas -flow oil-shale retort is a continuous, crass flow, gas -to -broken solid heat-exchange system in which heat is transferred by convection from the gas to the solide.2/ This type of heat transfer presents a problem of analysis that cannot be solved by methods in common use. Solution of this problem is necessary for design, operation analysis, and predict ion wherever that type of heat exchanger is used. This report embodies a method for calculation of heat transfer coefficient and temperature histories of gas and solid in the gas- flow retort operating at equilibrium conditions. Detailed calculations are presented to show the application of the method explained in this report to conditions of an actual run made in the gas-flow retort. Although used here for a specific case, the method is applicable to all heat exchangers that are characterized by continuous, crossflow, gas -to-broken solid heat transfer. INTRODUCTION In any direct, gas -to -broken solid heat -transfer system, it is difficult to measure the temperatures of the gas and solid inside the heat exchanger. The driving force for heat transfer between the two media in the bed there- fore usually is unknown. The major resistance to heat transfer is in the gas film surrounding the solid particles, and the thickness of this gas film is neither uniform nor can it be determined readily. It is well to point out also that determination of the surface area of the particles is of poor accuracy. Since the driving force, the major resistance, and the surface area in the heat-transfer system are such uncertain quantities, It is not feasible to calculate the heat transfer by usual methods. All of the fore- going statements are true of the gas-flow retort; as a result, efforts were made to determine apparent heat-transfer coefficients and temperature histories of gas and solid in the heat -exchange bed by calculation using those data that were available. The heat -transfer coefficient calculated has the following dimensions: B .t .u. per second, °F., cubic foot of bed volume, where heat - transfer coefficients normally have the units; B .t .u . per hour, square foot, °F. Only the Schumann-Furnas formulas may be used to determine the heat- transfer coefficient and temperature histories in this type of heat exchanger.

Jan 1, 1953

By Walter E. Lewis

Ventilation-air-heating plants are in use at several iron mines on the Menominee Iron Range, Iron River, Mich. Many of the mines are exceptionally wet; during winter months, when fresh air is forced down the wet air shafts into the mine, it is usually necessary to heat the fresh air to above freezing so that the openings will not be closed by ice. The problem of ice closing air shafts has been solved by the practice of reversing the air current before the openings have become completely closed. This procedure involves drawing warm air from the mine up the usual down-draft air shaft. The M. A. Hanna Co. has found, at some of their mines on the Menominee Range, that it is more convenient to heat the below-freezing air rather than reverse the air current. Intermittent freezing and thawing of ice that has formed in the air shaft tends to loosen the wall rock, requiring major shaft repairs. The openings are kept free of ice the year around by heating the fresh air during periods of below-freezing weather. Table 1 shows the monthly minimum moan, maximum mean, and mean temperatures for the Iron River area. Under normal conditions of temperature, the furnaces are fired in November and usually are not allowed to go out until April of the following year.

Jan 1, 1951

By Jr. Dubaniewicz, Gregory M. Green, Kenneth L. Cashdollar

Laser-based instruments are used in areas where coal dust ignition presents a safety hazard. The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory ~NIOSH, PRL! is conducting a study to help determine when an optical beam may be considered a potential ignition source in underground coal mines or coal storage facilities. Researchers conducted experiments to determine threshold igniting powers for Pittsburgh seam bituminous coal dust clouds using an 803 nm continuous wave laser. For fine sized coal dust dispersed in air, concentrations ranging from 600 to 2000 g/m3 were the most easily ignited. A heated layer of coal dust that deposited on the fiber tip during dispersion ignited the dust clouds. Minimum observed igniting powers for laser beams delivered by 200, 400, and 800 mm core fiber optic cables and directed into coal dust clouds were 2.0, 3.0, and 5.0 W, respectively. Threshold igniting power was proportional to beam diameter, and threshold igniting power density decreased with larger fiber diameters. Ignition delay times averaged 0.6 s and did not vary significantly with laser power under initially turbulent test conditions and with flammable targets. Comparisons are made with the results of other researchers.

By Victor J. Lynch

The Andover-Sulphur Hill mines are 12 miles northeast of Andover and 5 miles southeast of Newton, in Sussex County, N.J. The property is situated on the Lehigh Valley and Hudson River Railroad and half a mile east of U.S. Highway 206. It is connected with the main highway by a hard-surfaced county road. (See fig. 1.) Howard J. Hewitt of Lafayette, N.J., has under lease the Sulphur Hill tract, consisting of 28 acres, and has an option on the Tar Hill tract of 106 acres. The Tar Hill property adjoins the Sulphur Hill on the northeast. (See fig. 2.) The Andover-Sulphur Hill property is owned by the Lenape Corp. of Andover, N.J., while the Tar Hill tract is owned by the Crane Iron Co. of Phillipsburg, N.J. These mines produced iron ore during a period of about 100 years but have not been operated since 1880. Zinc and lead sulfides occur mixed with iron ores in the lower workings of the old mines. A diamond-drilling program was recommended to determine the extent of the sulfide mineralization in depth and also to explore further the iron-ore deposits on the property. The project was started October 6, 1942, and finished November 25, 1942.

Dec 1, 1947

By Thomas E. Green

A solvent extraction procedure using 8-hydroxyquinoline and chloroform was investigated by the Bureau of Mines as a preconcentration technique for the determination of aluminum, calcium, cobalt, copper, iron, lead, magnesium, manganese, nickel, and zinc in large samples of high purity tungsten. X-ray spectrographic and atomic absorption methods were used to determine the trace metals after preconcentration. The presence of 10 grams of tungsten had a pronounced effect on the distribution of 8-hydroxyquinoline between the aqueous and chloroform phases. This change in the 8-hydroxyquinoline distribution in turn had an adverse effect on the extraction of the trace metals. Extraction efficiencies can also be adversely affected by an increase in the quantity of extractable metals present, as shown by radiotracer tests using 65Zn. Excess 8-hydroxyquinoline in the extracts did not interfere with the determination -of the serious interference in the combined ion exchange paper--X-ray spectrographic method. Although preconcentration by 8-hydroxyquinoline extraction was found to be partially successful, other preconcentrationn methods based on ion exchange and dithizone extraction were found to be superior.

Jan 1, 1968

By Yael Miron

Coal mines that undergo self-heatings, and specifically mines that sustain both floor heave and self-heatings, would benefit from the use of sealants to minimize air ingress to susceptible areas. The U.S. Bureau of Mines(USBM) evaluated three sealant systems for this purpose, bentonite-water mixtures, silicate gel, and guar gum gel. The guar gum-based gel was the only sealant that possessed the desired properties of elasticity, ease of preparation, adaptability to the mine, and a long life. In addition, since the gel consists mostly of water, it could quench or cool nearby heatings. Optimal formulations were determined in laboratory tests, and then tested in the USBM Safety Research Coal Mine. Two formulations resulted in stable gels that lasted for at least 12 months in the mine. Semi continuous preparation of gel using an eductor was evaluated and appears feasible. Although guar gum gel is expensive, selective use to prevent heatings in specific areas would be cost-effective, both interms of productivity and enhanced mine safety.

Jan 1, 1995

By Edward L. McHugh, Charles Sabine, Louis J. Denes, Jami M. Girard, Peter Metes

The Spokane Research Laboratory, National Institute for Occupational Safety and Health, is investigating various remote sensing technologies as possible tools to detect, monitor, and mitigate hazardous situations in surface mines that could lead to catastrophic slope failure. Promising technologies include a field-portable spectro-polarimetric imager and a stationary interferometric radar device. Field tests were conducted of a prototype visible and near-infrared spectro-polarimetric imager (SPI) built at the Carnegie Mellon Research Institute. The SPI employs anacousto-optical tunable filter (AOTF) to control wavelength, a phase retarder to measure polarization signatures, and a digital camera and computer to capture data. Images obtained at the Mountain Pass and Castle Mountain mines in southeastern California showed that the instrument is capable of obtaining hyperspectral images of highwalls, outcrops, hand samples and drill core in the field. We have retrieved spectra from Mountain Pass images that closely match those of bastnaesite and have had some success in classifying images. Although radio frequency noise in the data limited spectral classification of imagery, we project that careful alignment of the AOTF should minimize the noise and greatly improve classification.

By Lester G. Morrel

THE RICH and varied occurrences of metallic ores in Australia, extensive nickel deposits on New Caledonia and phosphate rock on several widely scattered small islands were important aspects of the economy of the South Pacific area. Relatively small quantities of gold and nonmetallic minerals produced in New Zealand, Fiji, and the Territory of Papua-New Guinea remained important to the domestic economies of these islands, but had little importance to overall world mineral supplies. The value of mineral commodities produced in this area in 1964 was estimated at $658 million,3 compared with $585 million in 1963. The year's greatest commodity gains were in bauxite and aluminum, beryl concentrate, manganese ore, nickel smelter products, tin, and coal. Annual increases were recorded in virtually all countries and possessions in the area except Papua-New Guinea, where the drop in output of alluvial gold accounted for a decline of about $160,000. Mineral industry activities in Australia overshadowed those in all other parts of the South Pacific in 1964. Outstanding developments were the sales contract negotiations and physical preparation for exploiting the rich iron ore discoveries in Western Australia, the initiation of domestic crude oil production, the commissioning of two new steal mills and an alumina refinery and a start on the new alumina-aluminum project based on Cape fork bauxite deposits. The principal mineral development in 1864 in New Zealand was the progress on plans of the Newzealand Steel Co. to use indigenous iron sans as the resource base for a local steel industry. In New Caledonia, additions and expansion of the nickel mining and smelting facilities continued throughout the year. Plans for extensive geophysical studies were announced by the Government Geological Departments of British Solomon Islands and Fiji.

Jan 1, 1966

To provide coal operators with an easy-to-use stress control design procedure to minimize coal mine bumps during room-and-pillar retreat mining conducted with available continuous mining machine technology. Approach The goal of this U.S. Bureau of Mines (USBM) re¬search was to facilitate safe and efficient room-and-pillar retreat mining of bump-prone coalbeds by limiting coalbed stress adjacent to expanding gob areas through variation of section layouts. The first step was design of total-extraction pillars and their associated pillar-extraction plans. The second step was development of a coalbed strength model. The third step was development of stress limit design criteria. The fourth and final step was development of a methodology to estimate the magnitude and distribution of development and abutment loads apllied to the pillar line. The linear geometry of unlimited-width sections allowed for the accomplishment of step four with the tributary-area and linear shear-angle concepts. Increasing overburden depths required limited-width sections separated by barrier pillars to control stress within total-extraction panels. The accomplishment of step four with limited-width section designs required prediction of abutment load distributions for rectangular gobs and apportionment of these loads over mixed pillar sizes. A parametric study of the complicated interaction of various combinations of overburden depths, total-extraction panel widths, and abutment pillar widths was conducted with the USBM-developed boundary-element program MULSIM/NL.

Jan 1, 1995

By Paul J. Barrett

The Bureau of Mines evaluated a sulfurous acid-sulfuric acid process for recovering alumina from clay, in which clay is leached. successively with sulfurous acid and sulfuric acid. The resulting aluminum sulfite and aluminum sulfate solutions are combined and heated to produce a basic aluminum sulfate and sulfur dioxide. Alumina is extracted from the basic aluminum sulfate as sodium aluminate by leaching with dilute sodium hydroxide. After desilication, sulfuric acid is used to precipitate alumina as alumina trihydrate, which is then calcined to alpha-alumina. The estimated fixed capital cost for a plant producing 1,000 tons per day of alumina is about $74 million on a 1971 basis. For comparison with previous alumina-from-clay evaluations, the estimated fixed capital cost for the plant is about $67 million on an M and S Chemical Equipment Index basis of 24.0.0, which is equivalent to a 1960 cost level. Because the operating cost is highly dependent on fuel and electric power costs, graphs are included to show the effect of these items on the operating cost. On a 1971 basis, with natural gas costing 35 cents per million Btu and operating labor costing $4 per hour, the estimated operating cost is about $100 per ton of alumina. On a 1960 basis, with labor costing $2.30 per hour and natural gas costing 25 cents per million Btu, the estimated operating cost is about $86 per ton of alumina.

Jan 1, 1973

By Mark R. Stephenson

Everyone knows that mining is a noisy job, but did you know that you are nine times more likely to lose your hearing than someone who works in a quieter job? If unprotected from noise on the job, by age 50, you will probably need hearing aids. Obviously, the best solution is to engineer out the noise, but that isn?t always im­mediately possible. Until mines are quieter, one way you can help save your vital sense of hearing is to use hearing protectors whenever the noise around you is hazardous. Even if you already have some hearing loss, you can use hearing protectors to prevent your hearing from getting worse. When loud noise is present, proper use of hearing protectors will help miners pre-vent most or all noise-induced hearing loss.

Jan 1, 1998

By Paul R. Amyotte, Omotayo Kalejaiye, Kenneth L. Cashdollar, Michael J. Pegg

The Siwek 20-L chamber is widely used throughout the world to evaluate the explosibility of dusts. This research evaluated the quality of dust dispersion in the Siwek 20-L chamber using Pittsburgh coal, Gilsonite, and purple K dusts. A Pittsburgh Research Laboratory (PRL) optical dust probe was used to measure optical transmittance through the dust cloud at various locations within the chamber. A total of 540 tests were performed, with triplicate tests at five nominal dust concentrations and six locations. The two standard dispersion nozzles (rebound and perforated annular nozzle) were compared. The transmissions corresponding to the normal ignition delay period were used to: (a) determine variations in spatial uniformity of dispersion obtained with both nozzles; (b) make comparisons between the experimental transmission data and those calculated from theory for the three dusts; and (c) make comparisons with transmission data measured in the PRI, 20-L and Fike 1 -m3 dust explosion chambers. The uniformity of dispersion for the three dusts was similar with both nozzles, despite the differences in nozzle geometry and mode of operation. Transmission data of the three dusts were all significantly lower than those calculated from theory. This was discovered to be, in part, due to significant reduction in particle size that occurred during dispersion. By measuring particle sizes before and after dispersion, values of 60%, 50%, and 20% reduction in particle size (based on the surface weighted mean diameter) were obtained for Pittsburgh coal, Gilsonite, and purple K, respectively. Transmission data from the PRL 20-L, Fike 1 -m3 and the Siwek 20-L chambers indicated comparable results in terms of uniformity of dispersion. However, transmission data from the Siwek 20-L chamber were significantly lower than those of the PRL and Fike chambers. Again, this was attributed, in part, to the significant reduction in particle size that occurred during dispersion in the Siwek chamber. The design of the outlet (dispersion) valve of the Siwek 20-L apparatus charge vessel was largely responsible for the particle break-up. The contribution to particle break-up by the dispersion nozzles and the high level of turbulence in the chamber were found to be minimal. This is a significant finding in that the dust particle size tested for explosibility in the Siwek chamber is considerably smaller than the original dust sample.

By Will H. Coghill

[The supply of gravel spar and of acid spar is not well balanced. Gravel spar -- 85 per cent flourspar, 5 per cent silica -- gluts the market, whereas acid spar -- 98 per cent fluorspar, 1 per cent silica -- is somewhat scarce. Hence it is desirable to convert some of the gravel spar into acid spar. Knowledge of this condition prompted the Franklin. Fluorsrar Co. at Paducah. Ky., to enter into cooperation with the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy to improve the methods of fluorspar, milling so that morn acid spar would be available. The fluorspar company detailed Mr. Omar Greeman for the work. During the course of the investigation, while Mr. Greeman was also doing work for a master's degree in the School of Mines? an extensive study was made of gravity concentration of fluorspar ores. Decrepitation by heat treatment was also given a laboratory try-out. A part of tie time was spent on flotation; these notes relate only to the flotation. The results of one of the flotation runs is appended. The test was made in a 500-gram mechanical-agitation machine. The sample was ground to 100-mesh in a pebble mill.]

Jan 1, 1928

By E. D. Gardner

This paper is one of a series on milling methods being published by the United States Bureau of Mines. Atlanta is in Elmore County, Idaho, about 80 miles from the railroad at Mountain Home, Idaho. The concentrator is at an elevation of, 6,000 feet and located in a timbered, well-watered region of relatively heavy snowfall. The snow, however, does not seriously affect local operations. The track road to Mountain Home, which passes over a mountain range, is closed each winter from about November 1 to June 15. During this period concentrates are stored and bullion is shipped by airplane. Power is generated by a Diesel engine and by an auxiliary hydroelectric plant. Gold is the principal metal produced; the or also contains an able quantity of silver.

Jan 1, 1935

This part of the final report treats some problems related to coal mine carrier frequency communication systems using the trolley wire/track transmission line. This work was undertaken for a brief period of time during the summer of 1972 to help understand, quantify, and improve some of the trolley wire carrier system behavior observed and/or predicted. Calculations and estimates of transmission line characteristic impedance, inductance and capacitance per unit length, mine motor loading effects, parallel line effects, and connection impedances are presented in Chapter I. Chapter II treats the design of r-f isolators for reducing the undesired and troublesome r-f loading that mine motors present to the trolley transmission line. Chapter III treats a diversity method for combatting standing wave nulls. I. CALCULATIONS RELATED TO TROLLEY WIRE COMMUNICATIONS A. ESTIMATION OF INDUCTANCE AND CAPACITANCE PER UNIT LENGTH OF TROLLEY LINES To estimate the L and C per unit length of trolley lines, we use the eccentric line model of Section G of this Chapter, "Characteristic Imped¬ance Estimates for Mine Trolley Lines." The capacitance per unit length for an eccentric line is given by (1)

Jan 1, 1974

Permit quicker, safer clearance of hang-ups in the ore passes and chutes of underground mines. Approach Develop a device that can be operated from a safe distance to explosively propel a projectile into the hang-up. How It Works The Hang-Up Clearance Module, consisting of a stand, steel disk, explosive charge, and aiming device, is placed at a location convenient for line of sight aiming at the hang-up. This placement can be more than 100 feet from the target. Once aimed, the charge is remotely detonated, and the disk is converted by explosive force into a slug and propelled to the hang-up, bringing it down. The steel disk and an explosive charge are contained by a plastic casing. A small booster which is placed at the rear center of the explosive makes up the last component of the charge. Initiation is accomplished by standard means such as detonating cord or a number 8 blasting cap. When Initiated, a detonation wave travels through the explosive, inverting and consolidating the steel disk into a large slug. This slug is propelled at high velocity to the hang-up, delivering more than 5 million foot-pounds of energy on impact.

Jan 1, 1981