Search Documents

By David C. Oyler, Winton J. Gale, Jinsheng Chen, Christopher Mark

A collaborative project between RAG Emerald Mine, NIOSH, and SCT Operations was conducted to investigate ground behaviour, reinforcement performance, and stress redistribution in a coal mine entry subjected to a severe horizontal stress concentration. Field measurements indicated that the stresses applied to the study site nearly doubled during longwall mining, resulting in roof deformations extending to a height of 4.8 m (16 ft) above the entry. This paper focuses on the computer simulation that was undertaken to provide more insight into the roof behaviour and rock bolt interaction during mining. The model’s input rock properties were derived from extensive laboratory testing, and the model itself simulated a broad range of failure mechanisms. The effects of different bolt patterns on roadway behaviour were evaluated. Comparison between the model results and the field measurements indicated that that the model effectively simulated the critical elements of the actual roadway’s behaviour. With the confidence gained, the model was used as a baseline for additional simulations that evaluated the expected performance of alternative roof support systems. The study will also provide a benchmark data set for future applications of numerical modelling to U.S. coal underground mining.

By E. G. King

The work described in this Bureau of Mines report was undertaken to fill a need of industry for high-temperature heat-content data for uranium tetrafluoride. Without such data, heat balance evaluations of processes involving this substance are seriously hampered. Measurements of the heat content of uranium tetrafluoride were conducted at temperatures from 298° to 1,350° K. The melting point and heat of fusion were determined. The results are presented in suitable tabular form, and representative heat-content equations are included.

Jan 1, 1961

By Charles H. Shapiro

[In July, 1924, the Bureau of Mines, through its Petroleum Experiment Station, undertook a field study of methods used in oil-field shops for dressing and tempering fishtail bits. The purpose of this work was to suggest chances that would be helpful to the bit-dresser in turning out better treated, harder, and tougher bits, and thus cut down the excessive loss of time caused by too frequent changing of bits. It was the intention to eliminate as much as possible the guess work connected with dressing and tempering bits under the method of judging temperature by eye, by developing; practical methods of controlling temperature. If there were some possible means of accurate temperature control, then it would be an easy matter to bring all bits to the proper temperature for maximum hardness rued toughness, thus doing away with the source of most of the trouble experienced in the present method of bit tempering. Shortly after the Bureau of Mines began its study, a chop In the Stroud, Oklahoma, oil field announced method for tempering fishtail bits that Would increase the drilling footage of each bit treated. The method accurately regulates, by the use of a bath of molten salt, the temperature to which a bit is heated before being quenched to produce hardness. There is nothing new in using silt baths for the, heat treatment of steel, but this was the first attempt to introduce it into the oil fields for use in hardening bits, and for this purpose it proved to be admirably adapted. In tempering, by the old system it is not possible to measure the temperature of the heated bit by means of an electrical instrument for that purpose, whereas this is an easy matter with the now method. If heating steel to slightly above the critical point rind quenching suddenly will bring out its best properties, their here is a method of accurately bringing the steel to that point.]

Jan 1, 1925

By John M. Gomes

Two methods for electrowinning tungsten from wolframite [(Fe,Mn)W04] were investigated. The first method, direct electrowinning from wolframite concentrate dissolved in molten salt mixtures composed essentially of various combinations of sodium phosphates, sodium borates, and sodium halides, yielded impure products. The second method was electrowinning from a halide-tungstate melt that was obtained from a high-temperature, two-phase extraction of tungstic oxide (W03) from wolframite. Electrolysis in electrolytes prepared from addition of sodium metaphosphate (NaPO3) and boric oxide (B2O3) to the halide-tungstate melt produced tungsten metal of 99.9 percent purity. Tungsten carbide (WC) was electrodeposited from the halide-tungstate melt when the melt was adjusted to contain 82 mole-percent NaCI and 6.0 mole-percent each of W03, sodium metaborate (Na2B204), and caustic soda (NaOH).

Jan 1, 1970

By Rimas Pakalnis, Ted Williams, Tom Brady, Wilson Blake, Mary MacLaughlin, Kathryn Clapp, Cristian Caceres, Mario Morin

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining is generally necessary either due to a weak rock mass comprising the immediate back and/or high induced back stresses. A major concern in the design of sill mats is the loading and strengths associated with the overlying sill mat. This paper reviews past practice coupled with present observations and measurements from over ten (10) mines throughout North America. It outlines areas of concern in terms of design requirements.

By J. E. Zeilinger

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds of Beaver and Lawrence Counties, Pa. Washability analyses were made on seven coalbed samples, none of which were of metallurgical quality as received. Five of the samples could be sufficiently upgraded to produce acceptable products, and the remaining two samples could not be upgraded to metallurgical quality because their sulfur contents could not be lowered to meet the standard. For steam or power generation, one sample was of low sulfur content as received, one sample could be upgraded to low sulfur content, and three samples could be upgraded to medium sulfur content. The original sulfur content of the remaining two samples can be appreciably reduced by removal of the sink 1.58 speci fic gravity material; however, these coals would be classified as medium sulfur coals both before and after removal of the sink material.

Jan 1, 1969

By A. T. Iannacchione

Designing coal pillars to provide resistance against overburden and gob loads has long been an aim of rock mechanics engineers. This requirement has become more imperative as greater overburdens are encountered and when mining in stiff coal-bearing strata. Current design procedures rely on theories of coal pillar behavior that take into consideration a common hypothesis. This hypothesis states that the elastic core is surrounded by an inelastic yield zone. The distribution of stress at low-to-moderate pillar loads has been effectively defined by this hypothesis. However, it suffers greatly when applied to large width-to-height (w/h >lo) coal pillars under considerable overburden (>500 m) . In these situations, the hypothesis says the elastic core can achieve unrealistic stress states giving the pillars extremely high calculated strength. A growing body of field studies has shown this is not the case. It has become clear that same other mechanism must be involved. It is the purpose of this paper to discuss the importance of an interface slip mechanism between the coal- bed and the surrounding strata in controlling the extent and pattern of stresses and deformations in a coal pillar.

By M. J. Ferrante

Relative enthalpies of cuprous iodide (CuI) were measured at the Bureau of Mines to provide thermodynamic data for the advancement of min-eral technology. Enthalpy measurements between 298.15 and 1,396.3 K were made with a copper-block drop calorimeter. The temperatures of transition were measured by differential scanning calorimetry (DSC). Reversible transitions were determined at 643 K with a standard enthalpy of transition [(6Htr)] = 0.74 kca1/mol, at 679 K with a [6Htr = 0.65 kca1/mo1, and at 868 K] with a standard enthalpy of fusion [(6H~) = 1.895 kca1/mol.] Tabulated values are listed at selected temperature increments from 298.15 to 1,600 K for the standard relative enthalpy (HO -H298), heat capacity (CpO), entropy (SO), and Gibbs energy function [-(Go -H298)!T]. The enthalpy data are also given in the form of equations and combined with thermodynamic data from other investigations to derive values of standard entha1pies of formation [(~HfO)], Gibbs energies of formation [(6GfO)], and logarithms of the equilibrium constants of formation (log Kf).

Jan 1, 1987

By Forrest T. Moyer

OVERALL data for 1963 on injury experience and the levels of employment, worktime, and operating activity of the mineral industries are shown in the statistical tables of this chapter. The general groupings of the industries are presented in greater detail in Volumes I and II of the Minerals Yearbook. A corresponding chapter in Volume I contains additional breakdowns of the data on metal, nonmetal, sand and gravel, slag, and stone mines and quarries together with separate information on the related processing mills and plants including primary nonferrous smelters. The more specific information on the anthracite and bituminous-coal, petroleum and natural gas, peat, and natural asphalt industries is given in the similar chapter of Volume II. Injury and employment data were collected from coal producers on the mandatory basis required by the Federal Coal Mine Safety Act (30 U.S.C., sec. 455). Producers of all other minerals (fuel and nonfuel) voluntarily reported the requested injury and employment data. The figures for 1963 are preliminary except for anthracite, coke, petroleum and natural gas, native asphalt, and slag which are final. Data for earlier years are final. The figures represent full coverage for all industries except the oil and gas industries for which coverage is not complete, particularly with respect to small companies.

Jan 1, 1964

By Forrest T. Moyer

THE SAFETY record of the mineral and mineral-fuel-mining-and-processing industries retrogressed slightly in 1964, as indicated by the 3-percent increase in the frequency rate of all injuries. A slight improvement in the fatality rate was more than offset by the less-favorable rate of occurrence of nonfatal injuries. The overall-operating activity of these industries was lower in 1964 as measured by slight declines in employment and total man-hours of worktime. Injury Experience.-The rate of occurrence of all disabling work injuries in the mineral industries was 18.00 per million man-hours. This overall rate in 1964 comprised frequencies of 0.29 for fatal injuries and 17.71 for nonfatal work disabilities, which compared with respective rates of 0.30 and 17.20 in 1963. Fatalities totaled 538 or 30 less than in 1963. However, the total nonfatal disabilities of 33,151 in 1964 was 492 higher than in the preceding year.

Jan 1, 1965

By J. N. Van Sant

Lignite mining in North Dakota was begun about 1884 to supply the domestic needs of settlers. Annual production has grown rather slowly but steadily, exceeding 3 million tons in 1950. The western part of the State has lignite reserves, amounting to 351 billion tons, underlying an area of 28,000 square miles. Contour strip mining has almost completely replaced underground mining as the method of production. Lignite is often found under rather shallow and easily removed overburden, and this is the primary reason for the change in mining practice. Current mining operations are conducted where the overburden is 30 to 70 feet thick. Contour strip mining results in high production rates, at present 27 to 56 tons per man-day. These high production rates result in relatively low production costs.

Jan 1, 1959

By E. G. Valdez

The Federal Bureau of Mines, in cooperation with Ford Motor Co., investigated the recovery of polyurethane foam and other assorted plastics from the nonmagnetic reject of automobile shredders. Preliminary studies were con-ducted on a 1957 hulk augmented with additional foam and assorted plastics. The proposed flowsheet developed by the Bureau from the preliminary studies consists of a combination of screening, water classification, and gravity separation. The process was then tested on reject from two shredded 1972 cars. All of the foam and between 52 and 70 pct of the assorted plastics were recovered. The composition of the reclaimed foam concentrates ranged from 46 to 66 pct foam; the concentrates were hydrolyzed in laboratory tests by Ford Motor Co. to produce a reusable liquid mixture of polyether glycol monomers and toluene diamine.

Jan 1, 1975

Increase the recycling of critical and strategic materials by simplifying the indentification and segregation of scrap. Background Because the United States is dl-most totally dependent on imports of such critical metals as chromium, cobalt and nickel, Bureau of Mines research has been directed towards conserving these metals by increasing the recycling of the complex scrap materials that contain them. Experienced scrap sorters, using the traditional techniques of object recognition, spark tests, chemical spot tests, color, apparent density, and magnetic properties, can adequately sort a wide variety of alloy groups. However, the complex nature of new materials entering the scrap market has made sorting both more difficult and more important. Some new alloys contain so many components that separation by discrete alloys becomes a prerequisite for effective recycling. The Bureau has completed Investigations on two methods for rapidly sorting complex scrap mixtures. One method uses a combination of two low-cost instruments. The other uses a single sorting instrument. Both approaches are reported.

Jan 1, 1986

By T. D. Ralston

This Bureau of Mines report presents a mathematical model for heterogeneously catalyzed chemical reactors operating under turbulent conditions. The model includes reaction kinetics on the catalyst surface as well as diffusion of the reacting components within the reactor. Three applications of the model to tube-wall methanation reactors are discussed. The first application is a computation of catalyst activity from measured reactor data. This result is then used in a reactor sizing problem and a problem of reactor simulation with recycle. In addition to the reactor model, a novel approach to solving the recycled reactor problem is given.

Jan 1, 1974

By Roy T. Sorensen

This Bureau of Mines report presents the results of a study to rank technologies for extraction of alumina from bottom ash and coal shale. The available literature on composition and availability of coal waste was reviewed, and papers pertinent to alumina extraction are referenced. Types of coal waste were categorized by method of waste generation, coal content (heating value), location, coal type (ash nomenclature), and alkaline earth content. The differences and similarities among the categories of coal waste are summarized as to factors that my affect aluminum extraction, especially factors concerning chemical composition, current production, storage problems, and accumulated tonnage. Data available on physical characteristics and mineralogy did not correlate well with the individual categories of coal waste, and discussion on these two aspects is limited to the differences between coal ash and coal shale.

Jan 1, 1983

By David R. Forshey

This Bureau of Mines report presents a quantitative theoretical analysis of a coupled gasdynamics-heat release system involving the kinetics of water condensation in and behind the rarefaction wave in a shock tube using the method of characteristics. The merger of characteristics to form a shock wave is included.

Jan 1, 1977

By Joseph A. Sutton

The prospect of utilizing bacteria in mining and metallurgical processes introduces a new and challenging area of investigation. Elements of bacteriology and metallurgy are discussed in connection with possible areas where biological science might be applied in extractive metallurgy. Bacteria may prove important in the selective separation of metals from ores and metallurgical solutions, the production of sulfur from gypsum or pyrites, and the production of sulfuric acid from elemental sulfur. A series of reports concerning the experimental applications of bacteria on minerals and metallic ores will follow this paper. For several years the Bureau of Mines has been investigating the action of bacteria in the oxidation of sulfide minerals and their potential uses in metallurgical processes. Primary attention has been given to the possible utilization of certain strains of autotrophic bacteria that live in industrial leaching solutions or fractures of mineral outcrops. The purpose of this paper is to acquaint the mining and metallurgical engineer with micro-organisms and some of their possible applications in the field of extractive metallurgy.

Jan 1, 1961

By Brian G. White, Theodore J. Williams, Jeffrey K. Whyatt

Detailed mapping and examination of the site of a large rock burst at the Lucky Friday Mine, Mullan, ID, demonstrated conclusively that damage was caused by a splitting and buckling failure mechanism initiated by separation of rock into layers along steeply dipping metamorphic shear foliation subparallel to the affected crosscut. The thin tablular layers then buckled into the crosscut from both sides. Rigorous control of the burst by these layers suggests practical measures for avoiding bursts in crosscuts in the future by repositioning and reorienting openings so that splitting and buckling are reduced or precluded.

Develop technology for preparing thick corrosion-resistant coatings and electroforms of iron-chromium-nickel alloys. Approach To reduce the United States' dependence upon foreign sources for supplies of strategic and critical metals such as chromium, cobalt, and nickel, new technology must be devised to conserve these valuable commodities. One approach being investigated by the Bureau of Mines is the use of a modified-aqueous-electrodeposition method to prepare thick (-25 µm), complex alloy coatings (e.g., stainless steel composition) with properties similar to the commercial alloys. An alloy coating on a low-alloy steel or carbon steel substrate would require significantly less strategic and critical metals than those contained in an equivalent mass of the commercial alloy. Coatings applied to appropriate mandrel materials make possible the preparation of intricately-shaped alloy electroforms (near-net-shape parts). As a result, the loss of valuable metals associated with machining finished products would be minimized.

Jan 1, 1986

"Health standards in the U.S. are among the highest in the world. Achieving these standards have often had an impact on productivity, slowing output, and raising prices to levels that make it difficult to compete with many foreign industries. The answer to many of these problems lies in the development of new and advanced control techniques. This overview has identified some of the major respirable dust technological hurdles that have been overcome, and provided some insight into current and future approaches underway to remove these obstacles and to provide the United States with the most advanced state-of-the-art mining industry in the world from a respirable dust standpoint. The necessary developmental research is costly and time-consuming. The long-term, high-risk aspects of this effort are being addressed by the Bureau and the Generic Center on Respirable Dust, with support by industry. This should be recognized as one of the principal agents through which the great mineral potential of this Nation can be realized, and our international status as a mining power be assured without compromising the health and welfare of those who ensure it.The problem of more stringent dust standards will continue to grow. To date, approximately 40 pct of the coal mining industry has been placed on more stringent dust standards due to quartz. Control techniques must be improved if mandated levels are to be met. As longwall production increases, dust levels will also increase. In light of the industry trend toward longwall mining, if no new control technology is available, the Federal dust standard will act as a constraint on future output per hour. The Bureau has recently completed a survey of 18 coal preparation plants; 50 pct of these operate at dust levels which exceed 2.0 mg/m3; future work will be directed toward solutions in this area. The 2.0 mg standard for respirable dust is for dust particles which are below 10 pm in diameter. Recent studies have shown that dust in the range between 10 and 25 pm can cause obstructive airway disease. The Bureau is currently determining the extent of exposure to dust in this size range from various mining operations."

Nov 1, 1988