Search Documents

By Stephen Krickovic

A methane emission rate study was conducted in 1969 on a longwall section of a Lower Kittanning coalbed mine in central Pennsylvania. The longwall face was mined with a drum shearer between developed headings on the head end and headings on the tail end that were driven with a ripper-type continuous miner as needed. The study was conducted over 22 consecutive shifts (7-1/3 days). The average methane emission rate from the Lower Kittanning coalbed during mining at the face and developing the headings at the tail end of the face was 34 Am. Caving of the gassy overlying strata as the result of mining at the face increased the methane emission to rates ranging from 702 to 1,049 cfm.

Jan 1, 1971

By Donald O. Capstick

A mineral survey of a 13,525-acre portion of the 21,875-acre Owyhee Canyon Wilderness Study Area in northern Nevada was conducted by the U.S. Bureau of Mines in 1984. Two samples from sand and gravel deposits in the study area contained minor placer gold typical of the Owyhee River area. The gold-bearing gravels are too low grade or of insufficient volume to support commercial placer mining operations. The sand and gravel deposits might have minor local construction uses.

Jan 1, 1986

Provide roof to floor closure rate measurements during underground mining, especially retreat mining of coal pillars, thereby helping the miners predict an imminent roof fall. Approach An electronic device and rugged potentiometric extensometer were developed to provide a means fur measuring total closure and the rate of closure. How It Works An intrinsically safe, battery operated instrument is enclosed in a rugged, hand carried field case. The unit is constructed using low-power, integrated circuits to provide minimal battery drain. Two digital Light Emitting Diode (LED) readouts are used; one displays the rate, the other displays the total closure. The unit will measure one extensometer continuously or two extensometers alternately. Two potentiometric extensometers with a closure measurement range of 6 inches are attached to the readout unit. As the roof to floor closure changes, the potentiometric resistance

Jan 1, 1982

By Charles Findlay, Stephen Krickovic

A methane emission rate study was conducted in 1969 on a longwall section of a Lower Kittanning coalbed mine in central Pennsylvania. The longwall face was mined with a drum shearer between developed headings on the head end and headings on the tail end that were driven with a ripper-type continuous miner as needed. The study was conducted over 22 consecutive shifts (7-1/3 days). The average methane emission rate from the Lower Kittanning coalbed during mining at the face and developing the headings at the tail end of the face was 34 cfm. Caving of the gassy overlying strata as the result of mining at the face increased the methane emission to rates ranging from 702 to 1,049 cfm.

Jan 1, 1971

By E. C. Lane

The motor gasoline that is being marketed in the United States this winter (1928-29) is slightly more volatile than that gold a year ago. This characteristic is shown by a slight lowering of the distillation temperatures, particularly at the average initial and 20 per cent boiling points. Daring the past mine and a half years the Bureau of Mines has made semi annual surreys of the gasoline marketed in the United States; the Survey just completed is the nineteenth in the series. The 12 cities in which samples have been collected were chosen as representative of the more important marketing territories, as it was obviously impracticable to obtain a sample of every gasoline sold in the entire country.

Jan 1, 1929

By C. H. Elder, Fred N. Kissell, S. D. Maksimovic

The Bureau of Mines evaluated the hydraulic stimulation of a gob-degasification borehole to determine if this procedure would aid in degasifying a longwall panel. The stimulated borehole did not degasify the longwall panel as expected either before or after mining of the panel started. It reduced the underground methane emission only 11 pct, considerably less than the reductions effected by two unstimulated boreholes in the same panel. Some probable reasons for the reduced methane flow from the hydraulically stimulated borehole are very low reservoir gas pressure, location of hydraulically stimulated zones within the grouted casing, a casing break caused by lateral shifting, possible vertical movement of rock strata during caving, grouting of a 4-inch pipe blocking three stimulated zones, plasticity of shales, and possible hole damage by swelling of water-sensitive minerals. The borehole was also located between two second-mined areas, which may have allowed partial degasification of the overburden and the coalbed in advance of mining. Finally, a period of 3 months is probably not long enough for the borehole to degasify the overburden before mining.

Jan 1, 1977

By C. W. Smith

Research was conducted by the Bureau of Mines to determine the effectiveness of various types of crushers for use with the Bureau-developed pneumatic concentration technique for mica. Three types of crushers were investigated in this study, a roll crusher, a jaw crusher, and a hammer mill. All the mica concentrates produced contained over 82 percent mica, but recoveries varied considerably. The roll crusher gave the lowest recovery of 46 percent of the mica followed by the jaw crusher with a recovery of 50 percent of the mica. The hammer mill proved the most effective, producing four concentrates with recoveries of at least 70 percent.

Jan 1, 1981

By Wilbur I. Duvall

In this report, the Bureau of Mines presents a theoretical solution for the stresses and displacements in an infinite elastic plate containing a circular hole the boundary of which is loaded by applied radial stresses over four separated arcs. The problem solved is a two-dimensional approximation of the stresses and displacements developed by a large tunnel-boring machine anchored in a circular tunnel. Analysis of the solution shows that the tangential tensile stresses induced on the boundary of the circular opening can be minimized in the roof and maximized in the floor of the opening by proper spacing and loading of the four arcs.

Jan 1, 1967

By L. C. Marchant

Results of detailed analyses of four cores from the Threemile Canyon area in the P. R. Spring tar sand deposit in Utah are reported by the Bureau of Mines. The cores were obtained by the Utah Geological and Mineralogical Sur-vey as part of a l7-corehole evaluation program in the P. R. Spring, Hill Creek, and Rim Rock tar sand deposits. Average properties of the oil zone in the Threemile Canyon area as deter-mined from these cores are as follows: Oil saturation, 67.4 pet of pore volume; porosity, 29.2 pct; permeability before oil extraction, 133 millidarcies; and permeability after oil extraction, 2,855 millidarcies. Average net thickness of the oil zone is 23.8 ft and average depth to the top of the oil zone is 189 ft.

Jan 1, 1974

By Richard O. Kneisley

Microseismic activity observed in both the laboratory and underground indicates that a quiet period, associated with the closure of existing fractures and strongly influenced by coal seam microstructure, occurs prior to coal bumps. Field studies conclude that coal mine bumps occur against a background of this so-called microseismic calm. This Bureau of Mines report summarizes microseismic activity associated with face bumps and floor bursts in a deep, western U.S. coal mine. Results conclude that while bumps are often accompanied by panel-wide increases in microseismic activity, bumps are not only preceded by a localized decrease in activity, but occur within these quiet zones. The results of this study concluded that microseismic activity may be applicable to the global detection of potential bump-prone zones, but that future studies are necessary to confirm these findings and to improve the techniques for evaluating stress control effectiveness.

Jan 1, 1989

By Peter F. Strong, Robert L. Lagace, Alfred G. Exslie

The theoretical study of WF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a comer is the concern of this paper. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency that propagates with the smallest loss. The theoretical results are compared with published measurements. This work was part of an investigation of new ways to reach and extend two-way communications to the key individuals who are highly mobile within the sections and haulageways of coal mines.

Nov 14, 1974

Measure the daily exposure of individual miners to alpha particles emitted by radon daughters (radioactive decay products of the radon gas present in the mine atmosphere). Approach A dosimeter worn by a miner counts alpha particle emissions from radon daughters, RaA (Polonium 218) and RaC (Polonium 214), collected on a filter, and stores the gross count for later readout. How It Works A pump draws air into the detector assembly where radon daughters are collected on a filter. The detector, a solid state surface barrier type, is mounted in the filter head behind a thin mylar disc which serves as a moisture barrier. When a radon daughter decays and its alpha emission strikes the detector, the alpha particle causes a pulse of electrical charge in the detector. The circuits used to condition and count the electrical pulses generated in the detector are represented by the other blocks shown in the simplified block diagram. Each pulse is first amplified.

Jan 1, 1979

Reduce mine worker dust exposure by capturing airborne coal and quartz dust generated by a continuous mining machine. Approach Install a water-powered scrubber system operating at 1,000 psi on the side of a continuous miner boom. Dusty air under the boom is drawn through the scrubber, and cleaned air is discharged into the face return. How It Works Most coal mines use exhaust face ventilation to send fresh air over the miner operator, and contaminated air behind the line curtain to the section return. The difficulty with exhaust face ventilation is that the line curtain should be within 10 feet of the face for maximum effectiveness. If the line curtain is not extended properly, or water sprays for dust control are poorly installed, dust rolls back toward the operator. A scrubber mounted on the mining machine will effectively reduce this dust rollback and the dust in the return airstream.

Jan 1, 1989

By R. W. Stahl

Increasing use of continuous miners, especially the boring type, has focused attention on the inadequacy of face ventilation in coal mines. The bulk of the machine, the rapid advance of working faces, and the increased liberation of methane from the larger expanse of freshly exposed coal surfaces have created ventilation problems that were unknown with conventional mining equipment. Ignition of gas, especially that caused by machine bits striking hard rock or pyritic inclusions, have increased at an alarming rate. As the mines penetrate beds under thicker cover at an ever-increasing rate of face advance, this problem will probably increase unless face ventilation is improved. A previous survey, described in Bureau of Mines Report of Investigations 5414, Auxiliary Ventilation of Continuous Miner Places, disclosed that auxiliary fans with tubing generally improved circulation of air and removal of gas at the face. The study here reported attempts to examine, face ventilation at various mines and to note any plan or innovation of. air coursing that industry might adopt to reduce the danger of gas ignition. ACKNOWLEDGMENT The mines visited were very cooperative in the study-and-generously supplied any data requested.

Jan 1, 1960

To prevent injury to miners caused by violent whipping of mining machine trailing cables. Approach: The hydraulic cable controls are adjusted to reduce whip by visual reference of the cable sag to the height of the cable guide. How It Works: The cable sag is adjusted by visually estimating its height above the ground, at a specific reference distance behind the machine. This reference distance is measured horizontally back from the point where the cable leaves the cable guide. The Reference distance is 2H where H equals the height of the cable guide above the floor. See Figure 1. Cable sag should be less during rewinding than during unwinding. During cable unwinding, the cable height (at the refer¬ence distance) should equal 1/31-1. During rewinding, the cable height should equal ½ H. Field tests were made on several manufacturers' equipment after adjusting cable sag as above. Cable whip was greatly reduced for all, and whip was almost eliminated on a shuttle car equipped with a Joy Manufacturing Company 500108-104 cable reef and the newer (nonporous) shuttle valve. The following directions are for adjusting cable sag on a shuttle car equipped with a Joy Manufacturing Company 500108-104 Cable Reel equipped with the newer shuttle valve. Cable sag can be adjusted on machines equipped with other cable reels and valves by referring to the manufacturer's manual and making the appropriate cable valve adjustments.

Jan 1, 1976

By J. H. Maysilles

The Bureau of Mines is examining a variety of low-grade uranium ores because projections indicate that an appreciable percentage of future U.S. uranium production will be derived from resources containing 0.01 to 0.1 percent U308. One possible source is represented by a granitic material from Wyoming; the available samples contained 0.06 and 0.12 percent U308. Tests were conducted to explore the general leaching characteristics of this potential resource. The material responded to both acidic and alkaline leaching techniques. Conventional acid leaching extracted 93 percent of the uranium in 18 hours; the required acid addition was 50 to 100 pounds of H2S04 per ton of ore, and the oxidant addition was 3 pounds of NaCl03 per ton of ore. The acid consumption continues after maximum uranium recovery has been reached; this effect may complicate heap or in situ leaching with acidic solutions. Some variation in reagent requirements was noted between the two ore samples. Conventional carbonate leaching with strong solutions at 85° C extracted 94 percent of the uranium in 24 hours. These granitic materials also showed some response to dilute carbonate solutions, and the results suggest that the material may be chemically amenable to heap or in situ leaching with dilute carbonate solutions.

Jan 1, 1977

By S. C. Tadolini, T. M. Barczark

Mines in the western United States have had limited choices for standing support. Wood cribs were often too soft and unstable. The introduction of the Can support in the earl v 1990s provided an effective alternative, (lilt/ it remains the dominant form of tail¬gate support. Water-filled prestressing cells are now used to cap the Can and preload it to provide an active roof load. The Cluster Prop, consisting of three timber wedge props bundled to¬gether; provides more capacity than (m equivalent sized Call support and improves transport efficiency. However the Cluster Prop is less stable and does not maintain a consistent load throughout its loading profile. Pumpable roof supports are another alternative support, but the \' have not been proven in high deformation en¬vironments. This paper compares the performance characteristics o f these various support systems.

Reduce methane levels around the shearer machine during longwall mining by directing more of the available airflow along the face and over the shearer body. Approach To address the entire mining cycle, two techniques were combined to dilute and clear the methane liberated from the face by the shearer during cutting. The first is the modified shearer clearer system, which is used during the entire face pass. This is combined with the walkway curtain which is used only during the headgate cutout. How It Works Methane ignitions are one of the most potentially serious hazards facing longwall mine operators. The high rate of coal extraction on longwall sections can liberate a significant quantity of methane during a pass. The modified shearer clearer is used to dilute methane concentrations along the entire face for both cut directions. The shearer clearer system, originally designed as a dust control technique, uses a series of water sprays located on the shearer body to direct more airflow along the face and over the shearer. (See Technology News issues, #112, #118, and #221). The only change from the original shearer clearer design is the addition of three sprays to the return-side splitter-arm/ shearer interface. The additional sprays help to ventilate the area behind the shearer body.

Jan 1, 1985

By James J. Olson

The Bureau of Mines recorded peak particle-velocity levels and vibration frequencies to determine the nature and intensity of ground vibrations for tunnel blast rounds at the NORAD Complex, Colorado Springs, Colo. Previous Bureau of Mines studies in quarries and underground mines had shown that scaling (dividing) the distance from the blast by the square root of the charge weight removed the effect of the various charge weights on vibration amplitudes. The analysis of variance tests performed on the NORAD vibration data, however, indicated that the cube rather than square root scaling exponent grouped the data more effectively. The empirical propagation equation, V = 560 (D/w1/3)-2.04, where V is the maximum peak particle velocity in inches per second, D is the distance from the blast in feet, and W is the zero-delay charge weight in pounds described the attenuation, with distance, of the particle velocities from the tunnel blasts in the Pikes Peak Granite of the NORAD Complex.

Jan 1, 1972

By D. Z. Hobbs

Because an economic method for preparing pure boron has not been developed, a program was started by the Bureau of Mines to evaluate existing techniques or to develop new methods for preparing the pure element. This report describes investigations directed toward the development of techniques for the preparation of pure boron by fused-salt electrolysis. Only two of the several fused-salt baths tested were satisfactory for the preparation of boron. These baths contained (1) potassium fluoride, lithium fluoride, potassium fluoborate and boron trioxide; and (2) potassium fluoride, potassium chloride, and boron trioxide. Of these two mixtures, the latter was more satisfactory. Elemental boron of from 90- to 95-percent purity and, in isolated cases, as high as 98-percent purity, was prepared from these two types of fused-salt baths. There appeared to be no distinct differences either in the yields or the purity of boron prepared at current densities ranging from 795 to 1,000 amperes per square foot. Current efficiencies were as high as 85 percent.

Jan 1, 1961