Search Documents

By Charles Anema

The Mancarried and Helicopter Receivers were developed under the contract for trapped miner location. This program was a five phase program with 15 mancarried and 5 helicopter production receivers delivered under Phase IV and equipment documentation required under Phase V.

Jan 1, 1976

By J. F. Barkley

Smoke abatement is a subject of which fuel technology, although absolutely essential, is only a part. Its successful accomplishment starts and ends with human factors that must be given thorough consideration; between this "start" and "end" fuel technology is applied. Smoke abatement usually starts from the desire of some person or persons to be free from uncleanness caused by the stack of someone else and ends with the sincere desire of the operator of the fuel-burning equipment to maintain a clear stack. Although "smoke abatement been discussed for many years, it is only recently that the public has been mindful of such expressions as "air pollution" and "air hygiene." The subject has duel in common with that of supplying pure water but is more complicated. The public desires pure water, expects pure water, is willing to pay for pure water, and expects to continue to pay for it indefinitely; it is a development of civilization. It is doubtless correct to say, however, that people in general do not et realize the detriment of air pollution to their well-being or give the question enough serious consideration. This is illustrated by the fact that in city smoke abatement it is the mass of small householders that sins the most and is the hardest to handle. It is rather difficult to assemble a group of people in a room without the air becoming contaminated with smoke. Smoke abatement will lag with the lack of desire for pure air - probably the biggest human factor involved in its accomplishment.

Jan 1, 1939

By C. E. McElroy

"INTRODUCTION The ventilation of working places in mines by jets of air discharged from fan-pipe lines is an important phase of mine ventilation, whether the primary purpose is to dilute gas or dust concentrations or to provide air-motion cooling effect. Jets of similar nature are very prominent factors in the ventilation of enclosed spaces, such as buildings and ships. The effectiveness of such jets depends on the distribution of the air in the jet streams, a subject on which the little definite information previously available applied to jet discharge into large, open spaces under conditions quite different from those ordinarily associated with fan-pipe discharge in mines.The results of an initial series of experiments on the discharge of air from fan-pipe lines in mine openings have been described. 3/ This report presents the results of a second series of experiments and compares the results of both series with theory and experiment on jet discharge into large, open spaces. The results of this second series confirm and supplement those of the initial series, in which a 10-inch pipe discharged into an 8- by 8-foot develop¬ment end through seven short discharge pieces of different designs. In the present series the same 10-inch line was used, but the discharge was through 10- to 30-foot lengths of 5-inch, 10-inch, and 20-inch-diameter pipes and through a 20-foot length of 29- by 3-inch pipe. Tests were made with the air discharged into a closed drift or development end, as in the previous series (in which case the discharged air returned past the end of the pipe) and into an open drift (in which case the discharged air did not return past the end of the pipe but continued out along the drift). Test conditions corresponded to the discharge of a jet into a channel closed at one end; in one case, the discharge was directed toward the closed end and in the other toward the open end. The former typifies fan-pipe ventilation of development ends and the latter an abrupt increase in the sectional area of an airway. In both the flow had to pass from jet to open air against some resistance.The tests were made in the Mount Weather Testing Adit of the Bureau at Bluemont, Va., on the pipe line installed for ventilating the adit, and extended from late September to mid-November 1940. Preparations were made for directly comparable series of experiments on the injector effect of fan-pipe discharge in an open drift and on free expansion in large, open spaces, but these test programs were .first postponed in favor of other work and finally abandoned until the war is over."

Nov 1, 1943

By Clyde E. Williams

[As a results of work conducted during the past three years, the Northwest Experiment Station of the Bureau of Mines, in cooperation with the University of Washington at Seattle, Washington, has developed a process for the production of sponge iron. Commercial operation of this process in a 3 to 4-ton scale has been so satisfactory that its use on a large scale (20 to 100 tons per day) can be safely considered. Description of Process. The process consists in passing a mixture of iron ore and coal through a rotating kiln heated at one end to a temperature sufficient to convert iron oxide to metallic iron, discharging, cooling, and separating the sponge iron from the residual coke and silicious material on a magnetic separator. Both the coal and the ore should be crushed to peso as 6-meth scream, tans producing particles finer then 1/12 of an inch. Seventy-five parts of coal or other carbonaceous material arc charged with every 100 parts of ore), This large amount of coal is required in order to supply sufficient carbon to maintain a strongly reducing atmosphere in the charge, but may be reduced to about 65 parts per 100 parts of ore by recovering and using tae carbon that remains in the discharge product. Large-scale operation and refinements in furnace design should lower this ratio to perhaps 56 or 60 parts of coal to 100 parts of ore.]

Jan 1, 1924

By G. H. Gronhovd

This report describes the design and initial operation of a slagging gasification pilot plant installed by the Bureau of Mines at the Lignite Research Laboratory, Grand Forks, N. Dak., in 1958-59. The tests covered in this report were conducted over a period of about 2 years, beginning in April 1959. The pilot plant was designed for eventual operation at pressures ranging from 400 to 600 p.s.i.g. (pounds per square inch gage); however, for the preliminary test reported here, the gasifier was fitted with a low-pressure slagging section and operated at atmospheric pressure and at 80 p.s.i.g. The reason for using a low-pressure slagging section for initial operation was to facilitate modifications in design during the development of a reliable slagging procedure.

Jan 1, 1962

By James F. O?Neil

Brown iron ore deposits in Quitman County, Ga., were investigated by the Federal Bureau of Mines in cooperation with the State of Georgia, Department of Commerce, and the University of Alabama. Ninety-one holes were drilled, having an aggregate footage of 2,188 feet; seventy-one holes penetrated 248 feet of iron mineralization. Average thickness of the ore zone was 3.5 feet under an average thickness of 14.7 feet of overburden. The drilling developed inferred reserves containing nearly 30 million long tons of crude ore with an average analysis of 28 percent iron plus minor quantities of manganese. Test work done by the Bureau on the crude ore samples indicated that they would upgrade by current lug washer practice, with the use of a 1i8-inch screen, and yield 4.4 million dry long tons of concentrate with an average analysis of 52.1 percent iron plus manganese. The weight recovery obtained was 14.7 percent. Research studies made by the Bureau showed that the weight recovery would be increased by changing the screen size without any appreciable sacrifice of grade. The average weight recovery was increased to 18 percent with a 10-mesh screen and 22.8 percent with a 20-mesh screen. Screen tests studies indicated that there was no appreciable interlocking of the iron and manganese minerals and the clay and silica waste particles of the materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size.

Jan 1, 1965

By Sara J. Davenport

With the increased demand for mercury incident to preparations for national defense and the reduction in imports from some of the usual sources owing to war conditions, many small mines in the United States Pure now being worked that ordinarily would be unprofitable. This is indicated by the following table on mercury produced in the Unite States in 1939-40 (1)4/

Jan 1, 1941

By Pedro Lilienfeld

This report describes a program whose objective was to develop, design, fabricate and laboratory-test two prototype instruments capable of real-time selective detection and measurement of airborne fibrous-shaped particles. The operation of this fibrous aerosol monitor (FAM) is based on the rotation imparted to the acicular particles by means of a rotating quadrupole electric field of the order of 3000 V/cm. This field induces a dipole charge separation on the fibers and aligns them with the applied field. The selective detection of the fibers is effected by synchronous detection of the resulting modulation of the light scattered from a continuous-wave helium-neon laser beam by the rotating particles. The theory of operation, design of the electric-optical detection configuration and the electronic signal processing method are discussed. By means of a scattering pulse sharpness discrimination technique, fibers whose length exceed a selectable value are detected and their number concentration digitally displayed. Counting times of 1 to 1000 minutes permit the measurement of fiber concentrations between 0.001 and about 30 cm-3. A concentration of the order of one fiber per cubic centimeter can be assessed within a relative standard deviation of 10 percent with a counting period of 10 minutes. The FAM is a portable, battery-powered instrument capable of operating continuously for about 4 hours between battery charges. Preliminary tests with crocidolite and crysotile asbestos as well as with glass fibers were performed in the laboratory and the results indicate good correlation with the standard NIOSH phase contrast microscopy filter counting method.

Jan 1, 1977

By Gordon R. Sima

This contract is concerned with feasibility studies, design and fabrication of a prototype hand-held test instrument and a machine-mounted test Instrument for measurement of electrical shock hazards of mining machines. This report presents the proposed and detailed design of the hand-held test instrument and the machine-mounted test instrument. Theory of operation of each instrument is discussed and includes the operating parameters.

Jan 1, 1976

By Raymond Derzay

This publication is intended to be of value to the mineral industry in establishing and maintaining effective programs for preventing noise-induced hearing loss. Factors involved in this loss and the need for and the requirements of an effective hearing conservation program are discussed. The legal and legislative history of compensation for hearing loss is briefly reviewed. A review of statutes is not attempted since several States have recently modified) or are in the process of modifying their laws regarding permissible noise exposures) required hearing protection) and/or compensation for hearing loss. A review of other aspects of the problem of industrial noise in terms of medical, physiological) and psychological frames of reference is included. A hearing conservation program is described in detail. Appendixes detailing the names and addresses of a few equipment suppliers are included. References are provided for those who may wish to delve more deeply into the medical, technical, and scientific considerations of noise and its effect on man.

Jan 1, 1972

By Dennis R. Dolinar

The National Institute for Occupational Safety and Health?s Pittsburgh Research Laboratory conducted a full-scale test of a composite polyurethane-aggregate seal in a hydrostatic chamber at the Lake Lynn Experimental Mine. This composite seal consisted of a polyurethane and limestone aggregate core that was formed between two concrete block walls. In the hydro-static chamber test, water is used to pressurize the seal. During the test, the maximum average water pressure the seal was able to withstand was 18.9 psi. Further, the seal began to yield at an average water pressure of only 17 psi. At the time of the test, the minimum seal design requirement was 20 psi under 30 CFR4 75.335 (2005). Therefore, based on this test, the seal did not meet the regulatory minimum design requirement. Uniaxial compressive tests conducted on samples from the polyurethane-aggregate core revealed that both the compressive strength and the elastic modulus of the material were much less than that for polyurethane only with a density of 10.0?12.0 lb/ft3. The significant reduction in the strength and stiffness of the polyurethane-aggregate mixture results from the formation of a soft polyurethane foam around each piece of aggregate. The formation of the soft foam seems to be caused by residual moisture from the aggregate. The moisture also caused the density of the polyurethane in the polyurethane-aggregate mixture to be less than the design requirements. The lower density of the polyurethane in the mixture, along with the formation of zones of pure polyurethane only, resulted in the overall seal density being less than the design requirements. During seal construction, steps were taken to control the moisture, but were not successful. An analysis of the seal failure showed that the calculated shear stresses at failure and the estimated shear strength of the polyurethane-aggregate mixture are fairly close. This suggests that the strength properties of the polyurethane-aggregate mixture along with a weak zone of poorly bonded aggregate controlled the maximum pressure the seal could withstand. At the time of the seal testing, the minimum design requirement was 20 psi, as specified at 30 CFR 75.335 (2005). New emergency temporary standards for seal designs were promulgated on May 22, 2007, with a minimum requirement of 50 psi under specified conditions. However, it will be shown that the evaluation of the polyurethane seal performance as designed to meet the older 20-psi criterion can be relevant to the design requirements under the new standards.

Jan 1, 2008

By Allan M. Johnson

Case histories were used to document and evaluate deficiencies in underground mine closures which have resulted in post-operation problems such as subsidence shaft failures, acid or toxic water drainage and others. Three different underground mining districts in the United States were investigated; 1) an iron mining district in Michigan 2) coal mining districts in eastern Ohio and southern Illinois and 3) three metal mining districts in central Colorado. Previous work in the Michigan district on problems with subsidence and acid water drainage provided the background from which the concept for this project was developed Student investigators working towards their MS degrees in Mining Engineering did the work on the eastern coal and western metal districts. The combined studies show that problems from acid water drainage, subsidence and inadequately protected mine shafts are the most severe and widespread. Suggestions of a technical nature are presented as partial solutions to some of these problems. It was determined that pre-closure evaluations could result in the identification of some potential problems that may occur after the mine is closed. Early recognition of these problems would be an advantage for at this time more options are available to the mine operator to either prevent them or to plan for their occurrence. Mine closure and reclamation should be considered as a part of mining and be incorporated in the mining plan. This would result in reduced environmental impact and would be achieved at a lower overall cost to the mining companies and to society. The role of water in the occurrence of several types of subsidence during mine flooding was significant at some mines in the Michigan district. These mechanisms which involve, friction reduction, gravity loading, overburden transport and hydraulic forces in a flooded mine probably have a broader effect than is currently recognized. Control of these processes may offer some interesting options during mine closure. It is recognized that technical solutions alone cannot provide all of the answers to problems associated with underground mines. Education, modified attitudes on the part of regulators and operators, and a more realistic perception of the importance and value of mining by the general public are also needed.

Jan 1, 1983

By G. S. Scott

Mine fires have occurred since the mining of coal was begun, and they are still occurring. The resulting economic waste may become considerable (219),3 especially if a fire is allowed to assume major proportions or to get beyond control temporarily. It is important, therefore, to act promptly whenever a fire is suspected and to have every action count. To do this effectively, it is necessary to know at the earliest possible moment and thereafter what is happening in a remote or inaccessible area. It is equally important to know before¬hand what may be expected as a result of any proposed combative measure. The logical method of combatting a fire demands the cooperation of both mining engineer and chemist. They should decide the course of action to be taken, drawing upon the mining engineer's intimate knowledge of the physical structure of the fire area, the cost and time required for proposed operations, and the probable efficiency with which they could be carried out, and upon the chemist's knowledge of the results to be expected therefrom.

Jan 1, 1944

By Robert L. Lagace

The objective of this task was to perform theoretical analyses related to identifying and increasing the understanding of wireless propagation mechanisms in mines, and for predicting the performance ranges and limitations of proposed systems. This was to be achieved by building on and extending previous ADL work* and utilizing experimental data as they became available in the radio frequency bands of interest. B. TASKS Theoretical radio wave propagation investigations undertaken on this task centered on three areas. The first area dealt with extending previous UHF wireless propagation results*: to estimate the losses caused by the presence of haulage vehicles such as trains in coal mine tunnels; to estimate the propagation losses and wireless communication ranges expected along a longwall coal face tunnel; and to assess the applicability of previous analytical approximations to tunnels having reduced crossectional dimensions, such as those found in low coal and in the presence of haulage vehicles. The second area dealt with the development of a suitable propagation model to adequately explain the unexpected, highly favorable LF to MF band wireless radio wave propagation behavior experimentally observed in Consolidation Coal Co.'s Ireland mine. The third area dealt with the formulation of a model for evaluating the overall system transfer function and transmitter requirements for a hoist shaft LF communications system, taking into account the hoist rope/shaft transmission line characteristics, the cage and sheave wheel line terminations, the signal inductive couplers, and hoist shaft signal and noise data.

Jan 1, 1975

By Frank B. Fulkerson

Three of the five primary aluminum producers in the Pacific Northwest have facilities in the region to make aluminum mill products. Only one of the three, however, produces a variety of shapes and forms. The principal reason for the lag in development of an aluminum mill products industry was found to be transportation cost. The long range outlook is for expansion, based mainly on growth of the western market for aluminum used in construction, containers and packaging, electrical applications, diesel trucks, mobile homes, and irregation pipe. Consumption of western aluminum mill products in 1985 is projected at 1.1 million tons, compared with estimated consumption of 250,000 tons in 1961.

Jan 1, 1965

By James M. Link

A program was initiated tinder sponsorship of the U. S. Bureau of Mines to investigate pipeline behavior of raw and spent oil shale slurries. Slurries were recirculated in pipeline loops with 150-mm and 200-mm diameter horizontal test sections and a 150 -mm diameter vertical test section. Slurry concentrations from 10 to 60 weight percent were investigated. Critical and deposition velocities were observed. Head losses were measured at various velocities. Rheology measurements were made on representative homogeneous samples from the pipeline. From these data, pipeline energy requirements were predicted by computer and compared to pipeline data. Computer programs were also used to analyze pipeline data for two flow models: 1. Heterogeneous flow regime for coarse, settling slurries 2. Homogeneous flow regime for nonsettling suspensions The economics of slurry transport of raw and spent shale were examined. Cost estimates encompassed a range of pipe diameters to transport a wide range of throughputs of both raw and spent shale. Similar estimates were made for conveyor belt systems to provide a valid cost comparison. Economic comparisons are valid in a general sense, but a specific study must be made to determine the cost advantages of hydraulic transport for a given mine.

Jan 1, 1977

By Bernard M. Larsen, Clyde F. Williams, Edward P. Barrett

"Introduction.The Bureau of Mines at its Northwest Experiment station has been studying the production of sponge iron for the past four years, and during 1923 progress advanced to the point industrial applications can be safely considered. A furnace was operated commercially at silver City, Utah, producing about three tons of sponge iron daily.The Bureau was led to undertake this work by the interest in the use of sponge iron for copper precipitation and for conversion to iron and steel in the electric furnace.If a piece of iron oxide is completely reduced at such a low temperature (850 to 900° C) that no sintering or fusion takes place, then the piece of metallic iron formed has the same size and shape as the original piece of oxide on account of the removal of oxygen, the structure is finely porous, exposing a large surface of iron, and the apparent density is less than that of the original piece of iron oxide. This material is called ""sponge iron"". Chemically, it is a very reactive material."

Nov 1, 1924

The contractor examined L.T. White's Patent No. 3524680 and, finding it in need of engineering refinements, proceeded with a conceptual design of a variable wall mining machine. The contractor then proceeded to assess the feasibility of the variable wall mining machine measured against the criteria specified by the U.S. Bureau of Mines. The feasibility was judged from a physical aspect, a health and safety aspect, and an economic aspect. The Variable Wall Mining Machine was judged to be feasible on all three aspects provided that certain specified practices were adopted. Description The specifications and design and performance parameters of the Variable Wall Mining System as conceptualized are summarized in Tables I and II. The system consists of a side-cutting auger operating in a string of identical 12 ft. sections, along a 500 ft. retreating longwall face. In addition to the 41 identical sections, there is a special drive and discharge section at the head gate.

Jan 1, 2012

By R. Lusignea

A device has been developed for nondestructive testing the holding power of split tube friction rock supports. It operates by measuring the amount of decrease in internal volume when the support is forced into the drilled hole. The pullout force or slip load is a function of this decrease in volume. The device gives readouts of the average internal diameter and predicted pullout force or the support. Laboratory and field tests showed excellent repeatability and good correlation between predicted and actual pullout force. The device is hand-operated, lightweight (7.5 lb) and can be used on any friction support.

Jan 1, 1983

By P. Yant, R. R. Sayers, R. D. Lieitch

"PURPOSE OF INVESTIGATIONOf more than 300 bituminous mines examined by Crichton 5 and his assistants in connection with litigation in Indian Creek Valley, Payette County, Pa., only four were found to have alkaline water. That work and many observations from of the authors have shown the general prevalence or acid drainage from bituminous coal mines. In connection with investigations pertinent to coal-mine drainage that are being conducted by the United States Bureau of Mines, it was noted with considerable interest therefore, that a mine in the Thick Freeport bed about 20 miles north of Pittsburgh had no acid water in the workings, As it was thought that this condition might be common to all mines,this condition in this bed most of them were visited, samples of the outflow and from different parts of the mine inside were examined, and such general information as was available was gathered.ACKNOWLEDGMENTSThe authors acknowledge with thanks the courteous assistance of mine officials in connection with collecting the data for this paper, and of the analytical and coal laboratories of the Bureau of Mines for analyses."

Nov 1, 1932