Search Documents

By X. Yang, G. D. Zhai

The prop is the most important part to ensure the proper functioning of hydraulic support. When the hydraulic support is impacted by the roof, the prop is prone to extrusion deformation, expansion, and even bursting. In order to study the stress on a doubly-telescopic hydraulic support prop under impact load, an impact simulation was carried out based on the drop weight method. First, the impact model of the hydraulic system of the prop was established in AMESim software and the dynamic response curves of the bottom and middle cylinder of the prop obtained. Then, according to the conservation of energy, the pressure formulaes in the hydraulic cylinder of the prop under impact load were derived and verified by the AMESim simulation results, and the maximum pressure on the inner surface of the hydraulic cylinder of the prop obtained. Lastly, the transient dynamic simulation of a hydraulic support prop was carried out in ANSYS Workbench software, and cloud diagrams of stress and deformation of the prop obtained using Workbench simulation. The AMESim simulation process describes the change in fluid pressure in the prop, and the pressure formulae can be used to estimate the internal pressure of the prop under impact load. The finite element analysis results show that the stress of the middle hydraulic cylinder is much greater than that on the bottom hydraulic cylinder under impact load, which can provide a reference for prop design.

Jul 2, 2022

By Kym L. Morton

Ground water and associated pore pressure represent elements which can have a negative impact on surface mining and slope stability. Ground water flow and deformation within a slope influence each other. An increase in pore pressure will result in a decrease of effective stress; and conversely if the pore pressure decreases, the effective stress increases. Slope analysis and slope design calculations require good information on pore pressure distribution around an open pit excavation. Until recently very little pore pressure data was available and assumptions had to be used. Location and design of measuring points depend on geological and structural setting, geotechnical domains and practicality. Good planning and the use of sensitive point piezometers to measure in situ pore pressures means that real-time data can be collected and used for the construction of flow nets, the determination of pore pressure distribution around an open pit mine, the validation of the dewatering/depressurization requirements, the calculation of the efficiency of the dewatering system and finally the use of pore pressure data in slope stability analysis. The recommended layout for a monitoring system, types and design of piezometers, data collection and use of the pore pressure data are presented.

Jan 1, 2008

1. Book reviews Geostatistics for natural resources characterization, edited by G. Verly, M. David, A.G. Journel, and A. Marechal. Hingham (MA 02043, U.S.A.), D. Reidel Publishing Co., 1984. Pt I: 606 pp. Pt 11: 518 pp. U.S.$135,50 per set. Reviewer: D.G. Krige Magnesium, the international perspective, by Peter King. London, Financial Times Business Information Ltd, 1984. £120. 147 pp. Reviewer: D.G. Maxwell 2. Mintek reports Report M156 A kinetic study of the reactions of certain gaseous sulphur compounds with iron. Report MI57 Reaction mechanisms in the reduction of Winterveld chrome spinel with graphite and carbon. Report MI72 Computer programmes for the control and datamanipulation of a sequential X-rayfluorescence spectrometer. Report MI77 A proposed test for the determination of the grindabi/ity of fine materials. Report MI86 A survey of the erosion, corrosion, and abrasion of material-handling systems in the mining and mineralprocessing industry. 3. New journal Advanced materials & processes, issued monthly by American Society for Metals (Metals Park, Ohio 44073, U.S.A.). CIM conference The combined 24th Annual Conference of Metallurgists and the 15th Annual Hydrometallurgical Meeting will be held in Vancouver from 18th to 22nd August, 1985. Light metals The 8th International Light Metals Congress will take place from the 22nd to 26th June, 1987. These meetings, which take place traditionally every few years, are organized by the Austrian Metals Industry Association, the Austrian aluminium industry, and the University for Mining and Metallurgy in Leoben, in collaboration with the Aluminium-Zentrale Diisseldorf. President of AS&TS* Mr Arthur Woodington Reynolds (Sam) took office as President of The Associated Scientific and Technical Societies of South Africa on 28th November, 1984. Sam Reynolds was born in Boksburg on 27th December, 1930, and received his education at Christian Brothers College in Boksburg and at St John's College in Johannesburg. World mining Sweden, Finland, and Norway expect representatives of all mining countries in May-June 1987 to the 13th World Mining Congress in Stockholm. The Swedish Mining Association, the Finnish Association of Mining and Metallurgical Engineers, and The Association of Norwegian Mines will organize the Congress, together with the International Organizing Committee of the World Mining Congress. Sheet metal The German Group of the International Deep Drawing Research Group (IDDRG) will be organizing the 14th Biennial Congress of the IDDRG on 21st to 26th April, 1986, in Cologne and Munich. Safety in mines The 21st International Conference of Safety in Mines Research Institutes is to be held in Sydney from 20th to 25th October, 1985. ILAF A conferences The Instituto Latinoamericano del Fierro y el Acero (ILAFA) has scheduled the following congresses for 1985. Mechanical testing of materials The Deutsche Gesellschaft fiir Metallkunde, together with the Deutschen Verband fiir Materialpriifung and the Fachhochschule Osnabriick, is holding a course on the methods used for the mechanical testing of materials at Osnabriick from 9th to 11th September, 1985. Mine ventilation The Second U.S. Mine Ventilation Symposium will be presented from 23rd to 25th September, 1985, in Reno, Nevada, by the University of Nevada-Reno's Mackay School of Mines and Division of Continuing Education.

Jan 1, 1985

By H. E. James

During the past ten years there has been an upsurge of interest in the development of selective ion exchange resins and solvents, and of ion-exchange and solvent extraction equipment tailored to the special requirements of mineral-processing circuits. It is therefore not surprising that the recent Symposium on Ion Exchange and Solvent Extraction in Mineral Processing, held at the National Institute for Metallurgy (NIM) on 7th and 8th February, 1980, was a resounding success. This Symposium, organized jointly by NIM. Ion exchange and solvent extraction The Symposium on Ion Exchange and Solvent Extraction in Mineral Processing, which was organized jointly by the National Institute for Metallurgy, the South African Institution of Chemical Engineers, and the South African Institute of Mining and Metallurgy, was held in Randburg on 7th and 8th February, 1980. Analytical chemistry The Fifth International Conference on Analytical Chemistry, organized by the Chemical Society, is to be held at Lancaster University, England, from 20th to 26th July, 1980. Coal mining The First International Symposium on Thick and Steep Seam Coal Mining will be held in London from 18th to 21st May, 1980. Mineral processing The XIV International Mineral Processing Congress will be held in Toronto from 10th to 16th October, 1982. The theme of the congress will be 'Worldwide industrial application of mineral processing technology'. Sessions will be held on the following:

Jan 1, 1980

By J. Petersen, K. Shaik

The traditional route utilised for the recovery of Platinum Group Minerals (PGMs) in South Africa involves the concentration of ore by flotation, followed by smelting to produce a PGM rich matte, which is then digested hydrometallurgically to solubilise base metals and Platinum Group Elements (PGE). HCl/Cl2 is conventionally used for PGE dissolution from concentrated material, which is an aggressive reagent associated with high maintenance costs as well as environmental concerns. Of interest is the leaching of PGMs directly from mineral ores, low grade concentrates and tailings in a cyanide-ferricyanide system as a more sustainable alternative. This system has shown favourable Pt recoveries among the Pt minerals, but with sperrylite (PtAs2) displaying highly refractory behaviour. The dissolution of sperrylite is investigated in a cyanide-ferricyanide system in the context of an electrochemical study involving OCP, chrono-amperometry and cyclic voltammetry. This approach allows the assessment of leaching characteristics as well as the investigation of surface passivation, which is believed to contribute to poor Pt recoveries. Some evidence is presented that such passivation is related to the formation of arsenide species on the mineral surface. Keywords: Sperrylite, PGMs, cyanide, ferricyanide, electrochemistry

Jan 1, 2020

By B. J. Coetzee, P. W. Sonnendecker

The quality control of a two-stage coal washing process involves several complex components that need to be modelled accurately, to enable autonomous control of the process. The first objective is to develop a method to track the material through the washing process, while ensuring accurate washing prediction models are used. This was achieved through a digital twin model of the Grootegeluk 1 coal processing plant. The model is the amalgamation of manipulating and combining of data-sets from the plant historian, geological wash tables, and mining dispatch servers. This information is then used to control and set the processing medium densities of all 15 modules on the plant, 10 modules in the primary wash and 5 modules in the secondary wash. This controller has been successfully implemented and controlled the plant for 10 days.

Aug 2, 2022

By G. Song, S. Yang

"SynopsisThe development of techniques and equipment for single-pass high-seam longwall mining in China is reviewed. Some methods used to obtain the fractured zone height are discussed. The boundary between the caved and fractured zones is generally not clear, but one important difference that distinguishes the two zones is that horizontal compressional forces exist only between blocks of fractured zone. Based on this, a theoretical method is presented to investigate the destabilizing modes of the main roof (by sliding or rotation) and is used to determine if the main roof is in the caved or fractured zone. This method considers the mining height, immediate roof thickness, bulking factor, main roof thickness, main roof strength, main roof periodic weighting interval, and vertical stress in the overlying strata. To verify the method, a representative physical model of Wangzhuang coal mine is developed. The movement of overlying strata and fractured zone height are thus obtained. According to the results, the total collapsed height of the strata reaches about 70 m above the coal floor; the first main roof bending interval is 45 m and periodic bending distance is 10–15 m; the maximum strata subsidence is around 62 mm; and the presence of a three-hinged arch causes the fluctuation of subsidence in the same stratum level. Based on the theoretical and experimental analysis, the middle of the main roof is considered the boundary between caved and fractured zone; the caved and fractured zone heights are about 21 and 49 m respectively.IntroductionThick coal seams (>3.5 m) account for about 44% of the coal rescource/reserves and more than 40% of the total annual production in China (Zhao 2004; Wang 2009). Three mining methods – slice mining, top coal caving, and single-pass high-seam longwall mining – are frequently used in underground thick-seam operations. Compared with slice mining and top coal caving, high-seam single-pass longwall mining significantly simplifies the mining processes, reduces roadway excavation, and improves coal production, productivity, and recovery. The favourable economics, high production, and technical simplicity make high-seam single-pass longwall mining one of the most popular underground mining methods for thick coal seams in China."

Jan 1, 2015

By M. I. Brittan, E. J. J. van Vuuren

Computer analysis, modelling and optimization of gold recovery plants of the Anglo American Group by M. I. BRITTAN M.Sc. (Eng.), M.S., Ph. D., (Member). and E. J. J. van VUUREN M.Sc., (Visitor). Multiple correlation and regression techniques are used to analyse gold plant operating records. Key variables m the process which Influence the gold recovery are Identified and assembled into a mathematical model. This constitutes a valuable tool for the optimisation of variables such as the rates of reagent addition and for assessing the economics of extending the plant. Substantial short term economic benefits have been realized. The techniques provide a rapid diagnostic service without interfering with normal plant operation. Quantitative results are presented and their implications examined. The value of the method is discussed.

By G. L. Dyer, R. D. Alorro, R. E. Browner

A potential new rare earth extraction process has been suggested (Lazo, et al., 2017) (Lazo, et al., 2018) based on converting the rare earth elements to solid phase rare earth oxalates in an oxalic acid leach. Oxalic acid consumption is a significant issue in the process, therefore to improve the viability of this proposed new extraction method, a process to recover oxalate from the leach solution and recycle oxalic acid is required. A review of the literature and confirmation through thermodynamic analysis of the potential options identified precipitation of calcium or ferrous oxalate as the best potential options. The use of metallic iron to both provide ferrous ions as a precipitant and reduce ferric ions in solution would provide the most economical option, however slow kinetics and unreacted iron created significant issues with this process. The direct use of ferrous ions, while faster and more efficient, produced a precipitate with relatively poor solid/liquid handling characteristics and would require an intermediate stage utilising calcium in regenerating the oxalate. Utilising calcium chloride and oxide created very similar precipitates with better physical properties than the ferrous oxalate and that a reasonable proportion of the oxalate could be recovered before neutralisation of the solution induced precipitation of other phases such as iron oxy-hydroxides and calcium phosphate. The produced calcium oxalate was easily converted to oxalic acid and gypsum via immersion in sulphuric acid. It was also found that there is a significant loss of oxalic acid due to factors other than rare earth oxalate precipitation during leaching. This leads to a maximum oxalate recovery in the range of 50 %.

Jan 1, 2020

1. Book reviews Perspectives in metallurgical development. London, The Metals Society. 338 pp. £29. Reviewer: John V. Bee Mechanics of oil shale, edited by K.P. Chong and J.W. Smith. London, Elsevier Applied Science Publishers Ltd, 1984. 603 pp. £75. Reviewer: R.W.O. Kersten 2. Recent publications CANADIAN MINERAL POLICY SECTOR. Metallurgical works in Canada. Primary iron and steel 1984. Mineral Bulletin MR 203. Ottawa, Canadian Government Publishing Centre, Supply and Services, 1985. $6.00. Tin and its uses no. 143. Greenford (England), International Tin Research Institute, 1985. Mining 1985, edited by Diana Russell. Harlow England), Longman Group Ltd, 1985. 540 pp. £46. The following books are available from CRC Press, Inc., 2000 Corporate Boulevard N.W., Boca Raton, Florida 33431, U.S.A. Inorganic ion exchange materials, edited by A. Clearfield. 304 pp. $100. Polyurethane foam sorbents in separation science, by T. Braun. $80. Advanced particulate morphology: theory and practice, by J.K. Beddow and T.P. Melloy. 208 pp. $79. CRC handbook of atomic absorption analysis, edited by A. Varma. 2 vols: vol. I $114, vol 11 $102. CRC handbooks of inorganic elecrochemistry, edited byL. Meites, P. Zuman, E.B. Rupp, andA. Narayanan. 3. Mintek reports Report M169 The preparation of three South African coals for as reference materials. Report M190 The preparation and certification of a South African phosphate concentrate for use as a reference material. Report M191 The agglomeration of fine material for bacterial heap leaching. Report M197 A computer programme to monitor the performance of an X-ray-fluorescence spectrometer. Metallurgical award The 1984 Acta Metallurgica Gold Medal has been awarded to Professor John W. Christian of Oxford University. The medal is an international award that was established in 1974 to recognize outstanding ability and leadership in materials research. Proterozoic volcanic suites An international symposium will be held at the British Geological Survey, Keyworth, Nottingham, U.K., from 2nd to 5th April, 1986. Entitled 'Geochemistry and Mineralisation of Proterozoic Volcanic Suites', this special meeting of the Geological Society will discuss the geochemical evidence for the nature of volcanism during the Proterozoic. Powder metallurgy Every second year the International Powder Metallurgy Conference, the world's leading event in powder metallurgy, is organized and held alternately in North America and Eruope.

Jan 1, 1985

Book Reviews Linari-Linholm, A. A. Occurrence, mining and recovery of diamonds.Diamond Promotion Services (P.O. Box 62349, Marshalltown, Transvaal). 1974. Rl,OO. Metal Statistics 1962-1972. Metallgesellschaft Aktiengesellschaft. 60th Edition. Frankfurt am Main 1973. 328 pages. Published by Metallgesellschaft A.G., 6000 Frankfurt am Main, Reuterweg 14, Post Box 3724, Western Germany. Symposium on underground mining equipment maintenance~1973. Institution of Mining Engineers, and Association of Mining Electrical and Mechanical Engineers. Colloquium and general meeting A General Meeting and Colloquium on 'Motivation and productivity in the mining industry' was held on May 22nd, 1974, at Kelvin House, Johannesburg. Mr P. W. J. van Rensburg (President) was in the chair. The Colloquium was attended by 170 delegates and was opened by the President at 09h25. Minutes

Jan 8, 1974

DISCUSSION: The value of incentive payments in the mining industry by K; SMITH Published in the Journal, May 1974 H. P. CARLISLE* The author has drawn attention to one of the most important of mining problems, viz productivity, and in so doing has highlighted, perhaps inadvertently, the difficulty of assessing productivity. Competition for Students Each year the Institute offers a prize (or prizes should the entries warrant it) of up to R100 for the best paper or dissertation on a topic appropriate to the interests of the Institute. Corrigendum The Journal, May 1974, p. 377 We regret that the last portion of A. A. Hazell's contribution to the paper 'The value of incentive payments in the mining industry' by K. Smith was printed in the wrong sequence.

Jan 10, 1974

By S. Nana, M. B. Cortie

Duplex stainless steels containing high levels of manganese and copper and lower-than-normal levels of nickel were produced and evaluated. The experimental alloys containing 3 per cent copper by mass could not be successfully hot-rolled. Alloys containing less than 2 per cent copper could be hot- and cold-rolled without difficulty. The wrought experimental alloys that contained copper were found to offer some advantages over the 2205- type duplex stainless steel in sulphuric acid at 52°C. Resistance to pitting attack was governed primarily by the chromium, molybdenum, and nitrogen contents, and one of the experimental alloys was superior to the 2205-type alloy in the ferric chloride test. It is concluded that manganese is a useful substitute for nickel in duplex alloys, but that further work is required before the present alloys, or variations of them, could be commercially viable.

Jan 1, 1993

By J. D. Steenkamp, J. Muller

"Excavation of an industrial-scale submerged arc furnace, utilized in the production of silicomanganese, identified two high-wear areas in the refractory lining: the tap-hole, built with cold rammed carbon paste and SiC bricks, and the hearth, built with cold rammed carbon paste. To obtain insight into the potential causes of wear, thermodynamic calculations were conducted on eight sets of data, obtained for seven furnaces on three plants based in South Africa. FACTsage software and associated databases – FACTPS, FToxid, and FSstel – as well as the Mn-Fe-Si-C database of Tang and Olsen (2006), were applied. Theoretical indications are that chemical reaction between carbon refractory and slag, as well as dissolution of carbon and SiC refractory in metal, contributed to tap-hole refractory wear; and dissolution of carbon in metal contributed to hearth refractory wear. IntroductionDuring the excavation of a 48 MVA submerged arc furnace (SAF) used for silicomanganese (SiMn) production, it was found that the taphole and hearth were high refractory wear areas (Steenkamp, 2014). In both these highwear areas, carbon-based cold ramming paste formed the hot face refractory lining (crucible). The wear profile of this SAF is presented in Figure 1.The hot face refractory lining was formed by cold ramming of high-grade carbon ramming material. This material consisted of 50–70% anthracite, 15–25% graphite, 6–12% resin, 2–7% tar, 1–5% clay, and 1–5% alumina. The tap-hole was built using SiC bricks, consisting of 75% SiC, 23.4% Si3N4, 0.3% Fe2O3, 0.3% Al2O3, and 0.2% CaO.In the tap-hole area, the wear of the SiC refractory material was estimated at 0.4 t, and that of the high-grade carbon ramming material, at 1.9 t (Steenkamp, Pistorius, and Tangstad, 2015). The amounts of slag and metal tapped during six years of operation of the tap-hole (September 2007 to April 2013) were estimated at 33 088 t (Steenkamp et al.,2015) and 41 360 t, respectively."

Jan 1, 2016

By M. J. Deats

Your article on page 202 of the August 1993 Journal refers. I was surprised to read that this grant was first introduced in 1984 as it was awarded to me (albeit under the auspices of The Institution of Mining and Metallurgy, London) as long ago as 1964, and I spent two very profitable months in Sweden at that time. Training in job-skills * A South African mine is leading the way in providing alternative job-skills to staff in a bid to upgrade services in local communities and create greater economic empowerment. In recent months, 85 employees of the Associated Manganese Mine (ASSMANG) in the Western Cape have learnt skills as diverse as candlemaking, shoemaking, concrete-product manufacturing, and brick production through a newly established community training centre.

Jan 1, 1993

By Y. Jeong, K. Kim

Excess water can lead to instability and even failure in tailings storage facilities (TSFs). Simply reducing the amount of water in TSFs could be the best way to ensure the safety of nearby communities. In this case study we investigated the effects of reducing the water content in tailings slurry at a copper-cobalt-zinc mine in Mexico. An environmentally friendly polymer was used as a drag reduction agent (DRA) to offset the increase in solids percentage. The potential effects of the increased solids concentration on the tailings transportation system were also assessed. A series of ‘what if’ studies was conducted to assess whether adding the polymer would allow the solids concentration to be increased without changing the pressure loss in the tailings pipeline. The studies entailed conducting pipe loop tests to investigate these changes under various solids/ polymer concentrations and then constructing a computational fluid dynamics (CFD) simulation model using the test results. The validated model was used to determine the optimal polymer percentages needed to maintain the same pressure loss under baseline (30% solids) conditions, and to assess the potential risks (clogging, increased erosion rates) to the pipelines. The potential water savings were found to be significant, varying from about 1.852 Mm3/a at 35% solids to 3.915 Mm3/a at 45% solids.

Dec 13, 2023

By J. van der Walt, A. Whillier

Gravity-fed water systems in mines by A. WHILLlER, Pr. Eng., Se. D. (M.I.T.) (Fellow) and J. VAN DER WALT, Pr. Eng., B.A. Hons. (Bus. Admin.), Ph.D. (Eng.) (Visitor) South African mines often experience significant losses in production because of recurring shortages of water at work places as the result of underground dams running dry. Similar shortages have occurred during fire-fighting operations, and now, with the use of cold service water to aid in the cooling of mines, it is even more necessary that such shortages should be prevented. This paper draws attention to the primary cause of such water shortages, and an outline is given of some of the fundamental hydraulic principles that must be followed in the design of gravity-fed water-supply systems on mines.

Jan 4, 1977

By G. van Aswegen

The geometry and morphology of a set of low-angle fractures around a stope in a deep Witwatersrand gold mine are explained in terms of extension fractures forming under variable conditions of stress. Primary extension fractures (E1) form some distance ahead of an advancing stope along the s1, s2 plane. With stope advance, a couple of these fractures end up in a stress regime conducive to transpressional shear and a secondary set of extension fractures(E2) is formed at a high angle to the primary fractures. i.e. at a low angle to the stope. As the E2 fractures are undermined, they migrate into a stress regime of transtensional shear and a third set of extension fractures (E3) may develop between E2 fractures. These have sigmoidal shapes, being parallel to the E2 fractures at the E2 discontinuity where s3 is negative, and curved through the unfractured rock between E2 fractures where s3 is positive at the instant of fracturing. The fractures all display fractographic features characteristic of dynamic extension failure with striae indicative of the direction of rupture propagation and the local, instantaneous orientation of s1.

Jan 1, 2012

The case for national research in mineral processing PRESIDENTIAL ADDRESS given by R. E. Robinson*, Ph.D., B.Sc. (Eng.) (Wits.) Some of you have only raised your eyebrows, some have made tactful comments, and a few of you have been fairly outspoken, but all of you in industry are concerned at the high level of State expenditure by bodies such as the National Institute for Metallurgy. The case for a national research organization in mineral processing is not clear-cut and in fairness I must present both cases - for and against. Competition for student members Each year the South African Institute of Mining and Metallurgy offers a prize (or prizes should the entries warrant it) of up to Rl00 for the best paper or dissertation on a topic appropriate to the interests of the Institute.

Jan 10, 1975

By O. O. Ogunmodimu, D. K. Weatherley, M. S. Powell

Discrete element methods (DEM) have provided the ability to resolve the complex phenomena experienced by ore within comminution devices such as tumbling mills. The new developments in DEM techniques and the corresponding increase in computational power have made it more feasible to study the movement of individual ore particles as they traverse a tumbling mill. A range of information can be extracted on individual particle impact histories, such as kinetic energy at the time of collision, velocities of individual particles, per-particle stress tensors, impulse, and collision energy. DEM codes have been modified to provide required information that can be analysed in associated software to investigate the impact of varied operational parameters on the resultant granular dynamics. This paper explores the reaction of individual ore particles to the breakage environment within a tumbling mill using DEM techniques and studies the stressing conditions that would lead to either impact or abrasive breakage. Keywords: DEM, comminution, tumbling mill, breakage

Jan 1, 2020