Search Documents

By L. A. Vermeulen, D. D. Howat

New distribution functions are derived to describe the size distribution of grinding elements in ball mils. The formulations are based on the assumption that abrasive as well as impactive interactions occur during bal milling-an assumption that is supported by a large body of experimental evidence. It is shown that the functions can be used in the estimation of the magnitudes of abrasive and impactive components in the total rate of bal wear. The relative magnitudes of the wear components provide a basis for optimization of the chemical and metallurgical properties of the balls in a given milling situation. However, it is contended that these quantities are also useful indicators of the relative intensities of the abrasive and impactive interactions that are operative in the size reduction of mineral particles within ball mils. These quantities can be determined for any industrial ball mil, and their magnitudes provide practical guidelines for mil operation. The theory is used in an analysis of samples of ball charges from two industrial ball mils, and it is also applied to al the data on bal-size distributions found in the literature. The qualitative correlation between the calculated values of the wear components and the reported operating conditions is good for a variety of industrial ball mils, in conformity with the hypothesis that the relative magnitudes of the wear components are related to the milling conditions.

Jan 1, 1986

By G. E. Blight

The mining industry is making increasing use of pumped tailings fills. The properties that affect the performance of tailings fills are described by means of typical examples. They are the particle-size grading for maximum density, the water content for pumpability, settlement after placing, compression and drainage under stress, shear strength, and resistance to shock loading.

Jan 1, 1979

By J. G. Goodey, G. J. van der Linde

This paper describes pilot-plant tests on the recovery of apatite from a hitherto untapped material. This materialhydro- separator overflow-is very fine (80 per cent smaller than 45 µm and 32 per cent smaller than 10 µm). . The pilot-plant tests proved that the recovery of apatite from this material is economically and technically viable. This was confirmed by plant trials, which, in the early stages, produced concentrate assaying 36,6 per cent P2O5 at a recovery of 65,5 per cent.

Jan 1, 1983

By M. B. Cortie

An account is given of the development of ferritic stainless steels since their discovery in the early years of this century. The alloys became very widely used in the 1950s, the market during that decade being driven strongly by a demand for automobile trim made of ferritic stainless steel. The production of ferritic stainless steel declined as a proportion of the total at the end of the 1950s as consumer preferences changed. However, the market is now growing strongly again, this time driven by a demand for oxidation-resistant alloys for motor-vehicle exhaust systems. The tonnages produced, applications, and market shares of the various alloys are discussed and compared. Trends in world stainless-steel production, product forms, technological development, and usage are examined.

Jan 1, 1993

By A. V. Z. Brink

This paper describes the development of a monitoring architecture that allows for continuous monitoring of the process of mining, the underground environment, the state of the rockmass and its response to mining. The system is based on an open standard and is non-propriety. It allows for dense sensor arrays in the workplace, wire less communication to the closest power line, and TCP/IP communication to a central server. Continuous monitoring and quantification of the appropriate parameters allows a mine to optimise its mine process; to dynamically access the safety and health risk to people and equipment; and to quantify exposure to potential heath hazards such as dust, gas or noise. Current application examples of continuous monitoring include an application to optimise drilling and blasting thought fragmentation monitoring; an application of wireless sensor network-based monitoring in to provide early detection of potential rockfalls; and a trail to continuously assess the gold grade at the shaft through correlation with radioactivity. It is unlikely that a single monitored parameter will provide adequate knowledge of the assessed risk or even an optimisation approach. Multiple parameters are being combined using cognitive science tools such as Bayesian theory and other statistical methods to improve the accuracy and relevance of, for example, risk quantification. The decision maker is not confronted with massive amounts of raw data but rather with a single knowledge statement such a probability of failure, a human physiological strain index or an optimisation index.

Jan 1, 2008

By F. H. Deist, H. D. Small, J. D. Austin, L. F. Duvel

The development and application of a Computer System to aid in the planning of production in mines By F. H. Deist, L. F. Duvel, J. D. Austin, H. D. Small A computer system to aid in the planning of production in mines and its application to a complex colliery are descrIbed, The system consists of three phases, the data base maintenance program the 'production simulator' and the report generation facility, In the first part of the paper the categories of information kept on the data base and the functions of the simulator are described in general terms. The application of the system to a multi-product colliery operating a variety of mining methods in a number of superimposed seams is described m the second part. In conclusion some comments are made on further applications and intended future developments.

By E. J. Magri

Consideration is given to the problem of the estimation, from limited data, of the likely grade and tonnage for a new mining property that is to be exploited by the selective mining of two metals that have substantial contributions to make to the total revenue. In particular, the case of a new gold and uranium mine in South Africa is analysed as follows. (I) The applicability of the underlying lognormal bivariate model for different support (i.e. ore unit) sizes is examined. (2) The necessary parameters for the bivariate lognormal models for different block sizes are estimated from abundant chipsampling data from a section of the Hartebeestfontein Gold Mine using alternative approaches, and the results are compared. (3) A method is given for obtaining the necessary parameters for a tonnage-grade relationship relative to a joint pay limit from the very limited information likely to be available at the end of the exploration stage of a gold mine, and the results are compared with those obtained from the large volume of data available from a minedout area.

Jan 1, 1982

In China, thin coal seams are rich in resources but are technically challenging. The mineable reserves in these seams account for 20.4% of the total coal resources, while the current production accounts for only 10.4% of the total annual production. Characteristics such as narrow mining space, low level of mechanization, poor working environment, and high cost of mining, restrict the development of mining safety and efficiency. Recently, fully mechanized mining technology has developed rapidly for thin coal seams, the level of yield and efficiency has reached or exceeded the international standard, and some state-owned key coal mines are considering automation of their mining process. In thin coal seams with hard stone bands that contain concentrations of pyrite, a specialized software, LS-DYNA, is used to calculate the rational blasting parameters that are used in the deep-hole pre-splitting blasting. Using this method the hard stone bands are fractured effectively, and hence increasing the coal productivity. In addition, mining advance rate were increased by enhancing the level of fully mechanized equipment and safety improved by increasing gas drainage from the gas outburst prone seam located some 7 m below the coal horizon. At present, thin coal seam mining technology faces many challenges, including the low level of equipment automation, the low advance rate in mixed coal-rock ground, and the large number of the mine personnel underground. By lowering the labour intensity and improving efficiency through automation and other measures, more efficient working faces can be implemented in thin coal seams.

Jan 1, 2012

By G. P. Dyke

With the removal of the majority of the shallow mineral reserves there has been an increase in the mining depths in the South African mining industry. This has, in turn, changed the industry?s and stakeholders? perceptions of risk associated with mining-induced instability. In recent years the increased mining depth, particularly in open pits, has led to an increase in pit slope failures, which has highlighted the need for appropriate and effective pit slope management programmes. Such a programme comprises many facets, including mine hazard plans, regular slope inspections, cleaning of interim and final pit faces, blasting practices, histories of failures, pit depressurization, stormwater control and evacuation procedures. However, it is arguably in the field of slope monitoring that the most significant strides have been made in terms of new technologies and best practice in open pit mining geotechnics, with the introduction of technologies such as laser scanners and slope stability radar. This paper seeks to illustrate the operational benefits associated with the implementation of new technologies into open pit mining, using AngloGold Ashanti?s Geita Gold Mine in Tanzania as an example.

Jan 1, 2009

By L. P. Fatti

An important feature affecting the classification of a remotely sensed scene is that the data are, in general, spatially correlated. Various approaches are discussed towards incorporating the correlation between neighbouring pixels when they are classified on the basis of their spectral reflectance data.

Jan 1, 1987

By El-Sayed M. Sherif, J. D. Comins, Erasmus R. M.

Corrosion of copper in aerated acidic chloride pickling (0.5 M HCl) solutions and its inhibition by 3-amino-1,2,4-triazole-5-thiol (ATT) have been investigated using electrochemical techniques and weight-loss measurements, along with Raman spectroscopy. Electrochemical measurements for copper after varied immersion periods of 0, 24 and 48h showed that the presence of ATT and the increase of its concentration significantly decrease cathodic, anodic, corrosion (jCorr) currents and corrosion rates (KCorr), as well as the dissolution currents at 300 mV vs. Ag/AgCl, while increase polarization resistance (Rp), degree of surface coverage (?) and inhibition efficiency (IE%) to a great extent. Weight-loss measurements after different immersion periods of 6 ~ 48h revealed that the dissolution of copper decreased to a minimum and the corresponding IE% increased with ATT concentration increases. The detection of ATT molecules on the copper surface by Raman spectroscopy indicated that inhibition of copper corrosion is achieved by strong adsorption of ATT molecules onto the copper surface. Aerated acidic pickling solutions; 3-Amino-1,2,4-triazole-5-thiol; Copper corrosion; Corrosion inhibition; Raman spectroscopy

Jan 1, 2006

By Karl-H. Daum

Over many decades, numerous feasibility studies have demonstrated, that the production of sulphuric acid remains the most viable option of sulphur recovery from smelter off gas and abatement of SO2 emissions to the atmosphere. This is particularly more pronounced as smaller but more concentrated off-gas flows are to be treated from smelters, and enhanced sulphuric acid processes be-come available. Off-gas handling systems represent a significant capital and operating cost burden to the metallurgical operation. Modern pyrometallurgical smelter processes for sulphide ores based on the use of oxygen-enriched air, produce relatively small off-gas flows with high SO2 concentrations in the smelter gas of 30?60 %-vol. of SO2. This is a prerequisite for substantial cost reductions in the smelter off-gas handling and treatment system. As an alternative to sulphuric acid production, numerous scrubbing concepts with alkali or dual-alkali combinations as well as organic absorbents have been proposed. Also the reduction of the SO2 to elemental sulphur has frequently been studied. Very few of those alternative processes have been built in industrial scale, but all were generally characterized by none sustainable operation due to cost reasons, problems with issues related to chemicals used and by-products or poor availability. Thus the traditional concept of converting the SO2 to sulphuric acid is most common, although regarded as un-economic, but is at least a proven, environmentally sustainable and reliable way of sulphur gas processing. With the high acid price levels these days, operating companies are even able to generate significant revenue with their otherwise ?fatal? acid.

Jan 1, 2009

1. Book review Technology of metal powders- recent developments, edited by L. H. Yaverbaum. New Jersey, Noyes Data Corporation, 1980. 400 pp. (Reviewer: B. K. Loveday) 2. New books The use of microprocessors, by M. Aumiaux. New York, Wiley, 1980. 176 pp. $25,50. Aluminium smelter technology, a pure and applied approach, by K. Grojtheim and B. J. Welch. Diisseldorf, Aluminium-Verlag GmbH (P.O. Box 1207, D-4000, Federal Republic of Germany). 146 pp. DM48. Coal-bridge to the future. New York, Harper & Row, 1980. $35. System modeling and response.. theoretical and experimental approaches, by O. Doebelin. New York, Wiley, 1980. 576 pp. $26. Environmental and climatic impact of coal utilization, edited by J. J. Singh and A. Deepak. New York, Academic Press, 1980. 646 pp. $39,50. Proceedings of the Third European Conference on Mixing, York, England, April 1979, edited by H. S. Stephens and C. A. Stapleton. BHRA Fluid Engineering (Cranfield, Bedford Mk43 OAJ, U.K.), 1980. 2 volumes. 500 pp. $50. Lignite technology, edited by P. Nowacki. New Jersey, Noyes Data Corporation, 1980. 228 pp. $42. The application of rock mechanics to cut-and jill mining. London, Institution of Mining and Metallurgy, 1980. Papers presented at the Fifth International Symposium on Jet Cutting Technology, Hanover, Federal Republic of Germany, June 1980, edited by H. S. Stephens and B. Jawis. BHRA Fluid Engineering (Cranfield, Bedford Mk 43 OAJ, U.K.), 1980. 438 pp. £38. World coal resources.. methods of assessment and results, by G. Fettweis. Amsterdam, Elsevier, 1979. 425 pp. $80,50. Geophysical and geochemical techniques for exploration of hydrocarbons and minerals, edited by M. Sittig. New Jersey, Noyes Data Corporation, 1980. 300 pp. $40. Financial Times mining international year book 1980. Longman Group Ltd (Periodicals and Directories Division, Longman House, Burnt Mill, Harlow, Essex CM20 2JE, England). £24 surface, £34 airmail. National Symposium on the Availability of Strategic Minerals, edited by M. J. Jones. London, Institution of Mining and Metallurgy, 1980. 109 pp. 3. NIM reports Report No. 1941 The recovery of chromite and platinum from the UG-2 Upper Chromitite Layer .of the Bushveld Complex at the Pandora Mine (first published 10th Mar., 1978). Report No. .2012 A mineralogical investigation of borehole cores from the Trompsburg Complex (first published 6th Apr., 1979). Report No. 2038 The leaching of sphalerite in acidic ferric sulphate media in the absence of elemental oxygen. Report No. 2052 An investigation of the impurities in native gold by neutron-activation analysis. Report No. 2056 The mineralogy and geochemistry of the copper, lead, and zinc sulphides of the Otavi Mountainland. Report No. 2058 A n elementary introduction to image analysis - a new field of interest at the National Institute for Metallurgy. Report No. 2059 Distributed computer control of industrial processes. Report No. 2060 The analysis, by atomic-absorption spectrophotometry, of activated charcoal.

Jan 1, 1980

By M. Faure

The experiment with backfill at Harmony was mainly an attempt to improve the ground conditions in a particularly tricky section of the mine. A deslimed tailings system was selected for financial reasons, ease of installation, ease of operation and its low level of mechanization. The design of the system has three aspects: firstly, to define the parameters of the backfill material itself; secondly, to design a reliable plant which could consistently produce the desired material in sufficient quantities; and, thirdly, to design a fill distribution system for maximum reliability in the shaft, minimum pipe line velocity, pressure and cost in the horizontal sections and consistency and reliability at the delivery end. The system was successfully constructed and commissioned in a short space of time at a relatively low cost. It has now reached its full potential, and very encouraging results have been achieved with regard to cost savings, ground conditions, ventilation and accident statistics.

Jan 1, 1988

By R. Koen, H. Visser, A. Roodt

"SynopsisThe tetraethylammonium salt of the mono-anionic coordination compound mer-oxidotrichlorido(thenoyltrifluoroacetylacetonato- K2O,O’)niobate(V) (NEt4)[NbOCl3](ttfa)], has been prepared under aerobic conditions and characterized by single-crystal X-ray diffraction. (NEt4)[NbOCl3](ttfa)] crystallized in the monoclinic P21/c space group, with a = 11.483 (5), b = 12.563 (5), c = 17.110(5) Å, and ß = 100.838 (5)o. The complex structure exists in a 50.0% (NbA) : 50.0% (NbB) positional disorder ratio.IntroductionComplexes containing organometallic type ß- diketone ligands with O,O and O,N donor atoms are used widely in coordination chemistry and have applications in catalysis, radiopharmaceuticals, etc. (Schutte et al., 2011; Roodt, Visser and Brink, 2011; Brink et al., 2010; Otto et al., 1998). These ligand systems are very useful because of their highly coordinative nature, high solubility, and also due to their ability to be functionalized with various substituents on the carbonyl carbon atoms (Schutte et al., 2011).Only a small number of ß-diketonate ligands have successfully been coordinated to a Nb(V) metal centre, with only a select few being characterized by X-ray crystallography (Viljoen, 2009; Bullen, Mason and Pauling, 1965; Preuss, Lamding and Mueller-Becker, 1994; Funk, 1934; Davies, Leedlam and Jones, 1999; Allen, 2002. The synthesis and crystal structure determination at room temperature of mer-oxidotrichlorido (thenoyltrifluoroacetylacetonato- k2O,O’)niobate(V) {(NEt4)[NbOCl3(ttfa)]} was first reported by Daran et al. in 1979. Accordingly, for this current investigation, (NEt4)[NbOCl3(ttfa)] was re-evaluated at 100 K to determine if the structural features might change with temperature."

Jan 1, 2015

By R. T. Muller

Contribution to the above paper by R. T. Muller (Visitor) Demands are being made and pressure is being brought to bear on employers in South Africa to narrow or eliminate the wage gap between their White and Black employees. Few thinking people will dispute the fact that a constant improvement in the wages of Black personnel is essential, but this cannot be done merely by a redistribution of income in South Africa.

Jan 7, 1974

By E. Bakhtavar

There are many near-surface deposits with considerable vertical extent that have the potential to be mined by a combined method of open-pit and underground methods. In this regard, there is often a point called ?transition depth? where a decision has to be made whether to continue deepening the pit or change to underground methods. Recently, optimization of the transition from open-pit to underground operation has become an important challenge in mining engineering. Optimally, to model the transition problem on the basis of maximization of the profit from open-pit and underground mining, (0-1) integer programming has been used. In this method, block economic values of open-pit and underground methods should be imported to the transition model. A hypothetical example is presented in order to assess the model in detail.

Jan 1, 2012

By H. S. Sichel

This study deals with the development of some new theory concerning the bias which will result from the employment of the t-estimator if in fact the underlying distribution of ore values is not lognormal. It is found that the t-estimator is robust as long as the logarithmic variance is small and the shape factors of the transformed distribution are not unduly large. The choice of the threshold parameter [t] for the t-estimator is important, and some hints are given how to estimate it if the sample size is small, as en- countered in borehole valuation problems.

Jan 1, 1987

By D. J. Shields

The U.S. Bureau of Mines has developed a microcomputer-based mineral modelling system that enhances analytical capabilities of the agency. It draws upon the extensive data base previously developed for the Bureau's Availability studies. The model is first formulated as a generalized network flow optimization problem, the optimal flows from which are fed into a transportation algorithm. The goal of the modelling system is first to fulfill prespecified demand at the minimum opportunity cost and second to identify feasible, optimal trade patterns. The system facilitates the analysis of policy issues on a real-time basis and supports the Bureau's mission to assess mineral resources.

Jan 1, 1987

By Christopher J. Oates

Overview ? Mining Codes ? Best Practice ? Mining Standards Guidelines ? Get it right from the start ? External Auditors ? The 5% rule ? MMCRM's - The Key Components ? The MMCRM Report / Certificate ? MMCRM's & Round Robins ? Summary

Jan 1, 2005