Search Documents

By A. F. Lee

Dr E. C. Hanekom (Visitor): Two years ago we used the bubble pick-up technique as developed at Anglo American Corporation for screening candidate flotation agents prepared in our laboratories. It was obviously necessary to know to what extent the technique gave reproducible results and a statistical evaluation of the test method was made using a mineral sample provided by Anglo American Corporation. A bubble of 2.0 mm diameter was used and the measuring graticule was divided into squares (units) with sides of 5.0 mm at 25 X magnification. The mineral granules had diameters from 53 to 74 mm. The bubble was loaded by depressing it against a layer of mineral grains to give an arbitrary but constant compression of 0.4-0.5 mm. It was rolled five times through 2 mm horizontal displacement. The bubble was then lifted, its load compacted by gently stirring and the projected area measured in squares (units) on the grid. Each substance was tested at 5 ppm concentration in distilled water at five points in the pH range 3-6. With these standardized conditions of operation the reproducibility of the test was studied. Four materials were tested and at each pH value the procedure of forming a bubble, picking up granules and counting the units was repeated ten times. From these results the standard deviation for a single count at any pH value was calculated for each material (Table 1. The coefficient of variation of approximately 3 per cent was relatively low and it was decided that further refinements in the counting procedure would be of doubtful benefit with the present apparatus. Similar experiments were carried out with 12 sample materials. In this case the bubble formation and pick-up were repeated four times at each pH value, the mean value was calculated for each set of four observations and final pick-up values for the materials were obtained by selecting the highest mean count. Each test was completely repeated a number of times as indicated in Table 2 and the standard deviation calculated. The results allowed the selection of the more promising materials and the rejection of poor performers at the 95 per cent confidence level. All tests were carried out by one operator. Some evidence was obtained that the method is sensitive to operator bias. In conclusion it can be said that from all the results analyzed it would appear that once operation conditions are fixed (viz operator, pH control) the precision of the method is adequate. The author wishes to thank Messrs African Explosives and Chemical Industries Limited for permission to publish these data. G. S. Stander and C. J. Kooij (Visitors): We must congratulate Mr Lee for this most interesting and useful development of the pick-up experimental method. It certainly provides research workers with an instrument which makes flotation more of a science and less of an art. We visited Mr Lee at his laboratory where he gave us a demonstration of the bubble pick-up instrument and technique as developed and improved by him.

Jan 12, 1969

By P. N. Harris

The Colloquium on 'Recent Mining and Metallurgical Developments in the Orange Free State' was held at the Civic Centre in Welkom on the 4th and 5th May, 1983. The Chairman of the Orange Free StatejKlerksdorp Branch of the Institute and Acting General Manager of Unisel Gold Mining Company, Mr D. A. Parfitt, opened the proceedings, and Professor A. N. Brown gave the welcoming address. Mechanization of mining The South African Institute of Mining and Metallurgy is to hold a one-day colloquium on 'Developments in the Mechanization of Mining Operations' during September 1984. Surfac,e mining and quarrying The Second International Surface Mining and Quarrying Symposium is being organized by The Institution of Mining and Metallurgy in association with the Institute of Quarrying.

Jan 1, 1983

Exxaro installed their first ultra fines treatment plant at Leeuwpan Coal mine. The plant is now fully operational and results already show that the plant has great potential. The plant was designed and installed by DRA. Several challenges were faced during the installation due to the space constraints in the Leeuwpan plant. Efficiency tests were conducted on both modules after commissioning and showed very promising results. A lower ash product with a higher yield can be produced with the fine coal dense medium cyclones compared to the spirals previously employed.

Jan 1, 2010

By Q. Fu, Q. Wang, L. G. Wen, M. X. Jia, J. J. Zhao, J. W. Zhou

The BGRIMM process mineralogy analyser (BPMA) is a new automated mineralogy software platform developed in China. This system consists of the BPMA software platform, controlling a combination of commercially available scanning electron microscopy (SEM) and energy dispersive Xray spectrometry (EDS). The BPMA software controls SEM and EDS through their application programming interfaces, to form an auto-SEM and EDS system that automatically acquires BSE images and X-ray spectra, respectively, and classifies minerals by spectrum-matching. After automated measurement and mineral identification, various quantitative process mineralogical data (e.g., mineral composition, mineral abundance, mineral liberation and intergrowth relationships, mineral associations, particle and grain sizes, particle density distributions, calculated assay, elemental deportments, mineral grade recovery and elemental grade recovery, etc.) would be calculated quickly, accurately and automatically. The BPMA could be used for ore characterisation as a new advanced automated mineralogy technology. Keywords: BSE image; X-ray spectrum; automated mineral identification; quantitative mineralogical investigation; automated mineralogy

Jan 1, 2020

By M. Shaw, H. R. Heydenrych, A. E. Lewis, E. Glass, J. Chivavava

The removal of calcium from the retentates of reverse osmosis (RO) treated minewater is desirable since it allows the recovery of both additional potable water (through RO) and higher-purity salts (in downstream processing). This, in turn, reduces the need for costly and unsustainable evaporation ponds and enhances the economics and operability of potential zero-liquid discharge downstream processes, e.g. evaporative-, cooling- and eutectic freeze-crystallisation. For this study, a multi-component retentate high in sodium content was considered, typical of those emanating from minewater reclamation plants in Mpumalanga, South Africa. Four technologies were evaluated to remove calcium: gypsum precipitation by addition of lime; calcium carbonate precipitation by addition of soda-ash; heating crystallisation of calcium sulphate anhydrite; and cooling crystallisation of gypsum. Full processes were developed and simulated using electrolyte thermodynamics. Using the results of these simulations, capital- and operating costs, as well as revenues were calculated and used in economic comparisons of the processes. Sensitivities to key purchasing and selling prices were also investigated to understand the impact of changes in these variables. For the case of a low magnesium-to-sodium ratio in the feed, gypsum precipitation through lime addition was found to have the lowest operating and total annualised costs; but, if revenue could be derived from the sale of sodium sulphate, calcium carbonate precipitation through soda-ash addition was favoured. Keywords: Calcium removal, gypsum precipitation, calcium carbonate precipitation, heating crystallsation, cooling crystallisation, economic comparison

Jan 1, 2020

By G-L. Wu, S-W. Wu

"The hot deformation behaviour of Nb-Ti microalloyed high-strength steel was investigated. Hot compression tests were conducted in the temperature range 900 to 1100°C under strain rates of 0.1, 1, and 5 s-1. Dynamic recrystallization (DRX) occurs as the main flow softening mechanism at high temperature and low strain rate. The hot deformation activation energy was calculated to be about 404 699 J/mol. The constitutive equation was developed to describe the relationship between peak stress, strain rate, and deformation temperature. The characteristics of DRX at different deformation conditions were extracted from the stressstrain curves using the work hardening parameter. The Cingara-McQueen equation was developed to predict the flow curves up to the peak strain. The processing maps were obtained on the basis of a dynamic materials model. The results predict an instability region in the temperature range 1010 to 1100°C when the strain rate exceeds 0.78 s-1. IntroductionThe 700 MPa grade HSLA steel is widely used in engineering machinery, automotive beams, carriages, and axle tubes, etc. (Pan et al., 2017 ). Generally, such grades contain a moderately high amount of Mn (approx. 1.4% and above), and microalloying elements like Nb, Ti, V, and Mo to impart the desired strength and toughness through solid-solution strengthening, precipitation hardening, and grain refinement dislocation strengthening (Chen and Yu, 2012; Opiela, 2014). However, the production costs can be greatly reduced by replacing part of the Nb, V, or Mo with inexpensive Ti and adopting the compact strip production CSP process (Opiela, 2014; Chen et al., 2015). Furthermore, the microalloying technology coupled with new-generation thermomechanical control processing (NG-TMCP) has proved efficient for achieving the proper balance between strength, toughness, ductility, and formability by means of a suitable combination of chemical composition and thermomechanical treatment parameters (Shukla et al., 2012; Wu, Zhou, and Liu, 2017).In hot forming processes, the complex microstructural evolutions are often induced by multiplicative hot deformation mechanisms, such as work hardening (WH), dynamic recovery (DRV), and dynamic recrystallization (DRX) (Zhang et al., 2014; Liang et al., 2015). Dynamic softening behaviour during hot processing has generated considerable interest because component properties are influenced significantly by its corresponding microstructural evolution (Wu et al., 2010). During deformation in the DRX process, deformed grains are replaced with substructures and newly formed fine and uniformly distributed grains. This occurs only when a critical strain for the onset of DRX is reached, and at the same time, the minimum rate of energy dissipating is reached (Ferdowsi et al., 2014). DRV occurs at a high strain rate and low temperature, reducing the stored energy greatly and making DRX difficult (Liang et al., 2015). The microstructural changes during DRX are sensitive to the processing parameters, such as strain rate, deformation temperature, and strain (Zhang et al., 2014; Ferdowsi et al., 2014). Therefore, in order to optimize the hot processing parameters, it is important to understand the behaviour of hot deformation visà- vis control of microstructural evolution."

May 1, 2019

By Y. Makola, M. Kilumba, S. Mwaba, P. Ilunga, F. Banze, B. Nel, P. Kyoni, N. Mautsa, R. Nkomba, G. Ilu

Kamoto Copper Company is a copper cobalt mining company established in Lualaba Province of Democratic Republic of Congo under a Joint Venture between Glencore PLC and Gecamines (the state-owned mining company). Operations consist of underground and open pit mines, a concentrator producing sulfide concentrate and oxide ores milled slurry, and a hydrometallurgy plant producing copper cathode and cobalt hydroxides from concentrate and ores. The production capacity is 300 k/a of copper cathode and 35 kt/a of cobalt hydroxide. Since Q4 2020, the Luilu hydrometallurgy plant has experienced operational instabilities due to increase in proportion of dolomite in the ore mined and fed to the plant. This was diagnosed by the significant increase in calcium grade in ore and acid consumption, continuous foaming, and overflow of tanks with subsequent adverse impact on equipment availability due to corrosion caused by acidic spills, structure integrity, and safety concerns around the acidic slurry spills. Production was adversely impact due above equipment availability and often throughput restriction to mitigate the foaming and overflows. A high gangue-acid-consuming ore management programme was developed with the aim of mitigating these impacts. The programme included: (i) use of defoamer agent in leach to stop foaming and overflow, (ii) design of a mechanical solution to leach foaming and overflow, and (iii) froth flotation for copper and cobalt minerals separation from dolomite. Only option (i) is presented in this paper. Through laboratory testwork, pilot-plant testing, plant trial, and full plant implementation, Kamoto Copper successfully implemented a defoamer agent (Kemfoam X9980) dosing at leach, resulting in significant reduction in foaming and overflow of leach reactors and countercurrent decantation thickeners. The optimum defoamer dose rate obtained was 20 mg/L. Since then, the Luilu recovered its operational stability, the corrosion of critical equipment ceased, and availability improved as the acidic leach slurry spills ceased. The constraint on throughput due to leach foaming was addressed and the frequency of sliming events in the thickeners was significantly reduced as the foaming on the supernatant surface ceased, with subsequent significant reduction in interfacial crud in solvent extraction.

Jan 1, 2023

By G. Song, X. Liu

The global coal industry has changed significantly in recent years. In this paper we analyse the coal production and consumption, imports and exports, and coal prices in China and other major coal-producing countries during the past four decades. The analysis shows that global coal production and consumption have declined over the last three years, in striking contrast to the continuous growth for most of the past 35 years. Australia, Indonesia, and Russia have become the world’s major coal providers, while China, India, and the USA, and Germany are the major coal consumers. The world’s, and China‘s, coal industry can be classified into four stages of development: the stable growth phase, stable phase, rapid growth phase, and high-quality phase. Coal prices rose in the world’s four major coal markets in 2016 after four consecutive years of falling prices. The elimination of overcapacity and production-optimizing operations in China could assist in achieving a demand and supply balance.

Aug 8, 2024

By T. Bhambhani, J. Jankolovits

Sphalerite flotation using copper sulfate has been performed in the industry for decades and the mechanism of Cu activation is well established. Despite its ubiquity, many practical questions surrounding copper sulfate persist. It is not clear how iron selectivity is achieved in zinc circuits given the propensity of iron sulfides to be activated by copper. Also, the large variation in copper sulfate dosages across different plants and ore types cannot be explained. Lastly, Zn flotation with greatly reduced copper sulfate dosages attracts significant interest and has been demonstrated in certain laboratory settings, but no information is available on why those laboratory solutions have not been adopted in plant practice. Flotation studies are presented that demonstrate that Zn flotation with very low copper sulfate dosages is possible when using certain novel collectors that are not practised in the industry. However, these reagent schemes are impractical because of a heretofore unappreciated and critical role that copper sulfate plays in Fe rejection. With both very low and standard copper sulfate dosages, copper sulfate influences both Zn flotation and Fe rejection. The results highlight the multifaceted role of copper sulfate in zinc flotation and the need to holistically consider complex systems’ behaviour to understand flotation reagent mechanisms and optimise plant performance. Keywords: Sphalerite flotation, metal activation, copper sulfate, iron rejection

Jan 1, 2020

By J .. F. Brownrigg

In the mining method used at O'Okiep Copper Company (OCC), vertical crater retreat, the prime requirement for the fill is that it should be sufficiently strong to be free-standing to a height of 150 m. Other requirements are minimal decant and drainage water, and high pulp density to allow large tonnages to be placed quickly and alleviate transport problems. The excessively high cost of cement precluded the use of a cement-based fill, and after three years of extensive investigations a backfill based on the smelter slag was produced. Currently a fill with a uniaxial compressive strength of greater than 1 000 kPa after one month is being produced. This is in excess of the design specification of 850 kPa after 2 - 3 months. The research and development which went into the slagfill is briefly covered; the production of the fill from the various raw materials is described; and the design and control systems of the backfill plant, the reticulation system and its monitoring are examined. Finally, the implications of this high- quality fill for the mining programme are assessed.

Jan 1, 1988

By S. J. Thomas, P. A. Lilly

With support from the Australian mining industry and the Federal Government, three Australian universities are collaboratively developing flexible-format, web-based course content and delivery in rock mechanics for undergraduate mining engineering students. This paper describes the educational philosophy behind the development and summarises other salient features of the Program. Mit der Unterstuetzung von der austlalischer Bergbauindustrie und der Bundesregierung, drei austlalische Universtaeten in Zusammenarbeit entwickeln flexibel Netzgengruendet auf Lehrganginhalt und Lieferung in Felsgestein fuer Bergbaustudenten. Dieses Schreiben erlautert das Unterrichtsphilosophie hinter der Entwicklung und Zusammenfassung anderer Hauptpunkte von diesem Programm" Avec l'assistance de l'industrie miniere australienne et du gouvernement federal , 3 universites Australiennes collaborent a la mise en place d'un programme de mecanique des sols pour etudiants- ingenieurs en mines. Ce programme serait a la fois flexible et accessible par Internet. Ce document decrit la philosophie pedagogique de ce projet et en souligne les characteres importants.

Jan 1, 2003

By Q. G. Reynolds

The problem of direct-current plasma arc behaviour, interaction, and dynamics is considered in the context of metallurgical DC arc furnace applications. Particular attention is paid to the transient flow behaviour of arc systems. A mathematical formulation of the physics used to describe the arc system is presented, and includes the spatial and temporal evolution of fluid flow, heat transfer, and electromagnetism. Based on this formulation, a numerical model is developed using a finite difference approach on a regular cartesian grid in both two and three dimensions, with a special focus on robust stability, high resolution modelling, and high performance. A collection of results produced using the numerical model to study pilot plant-scale furnaces is then presented. These address a range of process and design variables and their effect on the numerical model?s results. Where possible, the qualitative behaviour of the model is compared to available experimental data. A number of novel effects and phenomena are seen in the dynamic behaviour of the DC plasma arc model for both single and multiple arc systems, which may lead to improved understanding, control, and manipulation of such systems where they occur in industrial applications. Keywords Pyrometallurgy, direct-current furnace, plasma arc, modelling.

Jan 1, 2010

By V. K. Risinggård, M. Sparta

We report on the development of a finite-element method model for a pilot furnace for the production of manganese alloys. The model is a multiphysics model that addresses material flow, electrical conditions, heat transfer, and physical and chemical transformations. It is capable of studying both quasi-steady and transient states in time-dependent simulations. The model includes common charge materials and fluxes and can simulate production of both ferromanganese and silicomanganese alloys with acid and basic slags, as well as changing charge compositions. The model output provides access to the material distribution in the furnace during furnace runs, temperature profiles, current paths, energy balances, and alloy and slag production rates and compositions.

Apr 16, 2024

By G. van Aswegen, J. D. Bosman

Gold bearing deposits in the Witwatersrand consist predominantly of narrow tabular conglomerates with quartzite host rock. Extensive mining of these deposits at depth results in significant stresses being induced in the periphery of the tabular excavations. Where remnant pillars are created excessive stresses have resulted in the dynamic failure of the abutments. At the Hartebeestfontein Mine four brittle shear zones have recently been exposed and investigated. For most part, they represent abutment failure into the weaker hangingwall strata, striking parallel to the abutment, dipping towards the stope, with a sense of displacement consistent with closure of the stope from above. These shear zones are similar to those described in various publications by Ortlepp2: they are essentially brittle shear zones characterised by the presence of very finely comminuted ‘rock flour’ on an obviously freshly sheared surface. The angle between the shear zone wall and extension fractures indicate the sense of shear and the intersection of the extension fractures with the shear zone walls define a strong lineation normal to the direction of slip. It is suggested that these structures are referred to as ‘mining induced dynamic brittle shears’. Les gisements d’or du Witwatersrand consistent principalement de conglomérats tabulaires peu épais contenus dans une quartzite mère. Une exploitation poussée de ces gisements en profondeur a pour résultat l’apparition d’importantes contraintes induites à la périphérie des excavations tabulaires. Là où des piliers restants sont créés, des contraintes excessives ont eu pour résultat une rupture dynamique des appuis. Dans la Mine d’Hartebeestfontein, quatre zones fragiles de cisaillement ont été récemment exposées et étudiées. Dans la plupart des cas, elles représentent une rupture des appuis dans les strates moins solides de la paroi suspendue, orientée parallèlement à l’appui, inclinée en direction du chantier d’abattage avec une direction de mouvement consistante avec l’affaissement du toit de la galerie d’abattage. Ces zones de cisaillement sont similaires à celles décrites par Ortlepp2 dans diverses publications: Ce sont essentiellement des zones cisaillement fragiles caractérisées par la présence de « farine de roche » très finement réduite sur une surface évidemment fraîchement cisaillée. L’angle entre la paroi de la zone de cisaillement et les fractures de tension indiquent le sens du cisaillement et l’intersection des fractures de tension avec les parois de la zone de cisaillement définit une forte délinéation perpendiculaire à la direction du glissement. Il est suggéré que l’on se réfère à de telles structures comme des « cisaillements dynamiques fragiles induits par l‘exploitation ». Goldablagerungen im Witwatersrand bestehen überwiegend aus schmalen tabularen Konglomeraten mit Quarzitwirtgestein. Der umfangreiche Abbau dieser Ablagerungen in der Tiefe resultiert in signifikanten Drücken, die auf die Peripherie der tabularen Aushöhlungen wirken. Wo Restpfeiler hergestellt wurden, resultierten exzessive Drücke im dynamischen Versagen der Auflager. In der Hartebeestfontein Grube wurden kürzlich vier spröde Scherzonen freigelegt und untersucht. Zum größten Teil representieren sie Auflagerversagen im Stratum der schwächeren Stollenfirste, parallel zum Auflager verlaufend, in Richtung Abbaustelle abfallend, mit einem gewissen Grad an Verschiebung konsistent mit der Schliessung der Strosse von oben. Diese Scherzonen sind jenen ähnlich, die in den verschiedenen Publikationen von Ortlepp2 beschrieben werden: sie sind im Wesentlichen spröde Scherzonen, charakterisiert durch das Vorhandensein des sehr fein pulverisierten „Gesteinsmehls“ auf einer offensichtlich frisch abgescherten Oberfläche. Der Winkel zwischen der Scherzonenwand und den Bruchverlängerungen deutet die Richtung der Scherung an und die Kreuzung der Bruchverlängerungen mit der Abscherzone grenzt sich gegen eine starke Lineation normal zur Richtung der Lehne ab. Es wird vorgeschlagen, daß diese Strukturen als `vom Abbau verursachte dynamisch spröde Scherungen’ bezeichnet werden.

Jan 1, 2003

By J. K. Pothal, S. Basu, R. Barik, P. K. Senapati, A. Dubey

The aim of this paper is to study the characteristics of limestone particles (size varies from 4 mm to 20 mm) during its transportation from open cast mines through pipes. The influence of four different size fractions of limestone samples (4–6 mm, 6–10 mm, 10–15 mm, and 15–20 mm) on pipe flow characteristics during vertical transport in a 100 mm NB hose pipe was investigated. The flow velocities in the vertically lifting pipe was varied from 0.95 m/s to 2.78 m/s and a rotary feeder of 2 to 4 tonne/hr. capacity was employed to feed the limestone samples to the lifting pipe. The pressure drop data for the different size fractions of limestone samples at different mixture velocities were analysed. The effect of input volume fraction and superficial velocity of limestone samples on hold-up ratio were discussed. It was indicated that there was no substantial increase in pressure drop of slurry samples in the studied range of concentrations (CW = 4.22% - 12.54%), particle size, and low to medium range mixture velocities with respect to water run head loss data. The hold-up for the larger size fractions (15–20 mm) of limestone samples was found to be significant as compared to smaller size fractions, which may be due to terminal settling velocities of individual fractions of the studied samples.

Mar 4, 2025

By J. Hadjigeorgiou, G. Knox

There is a considerable wealth of information on the behaviour of rockbolts under axial loading conditions both in situ and under controlled laboratory conditions. However, there is comparably less data on the behaviour of rockbolts in shear. Several authors have contributed to the understanding of the behaviour of conventional rockbolts’ performance under shear loading. Much of this data have been gathered through experimental programmes conducted on sections of the rockbolt. Considering the continuous coupling between the rockbolt and borehole interface, the approach is justified. Due to the design premise of energy-absorbing rockbolts with discrete couplings, full scale testing is required to quantify the behaviour of the rockbolts. This paper reviews published results obtained from two testing facilities, which are the SINTEF rockbolt pull test rig in Trondheim, Norway and the Epiroc Combinations Shear and Tensile test rig in Johannesburg, South Africa, both capable of conducting full scale testing of rockbolts. Based on this high-quality database it was possible to identify three distinct responses of rockbolts in shear. The behaviour under load is controlled by the presence or absence of an encapsulation medium (resin/cement grout), the reinforcement mechanism, and whether the rockbolt is continuously or discretely captured. As a reference the results are compared to the performance in shear of conventional grouted rockbolts.

Nov 24, 2025

By I. Zh. Bunin, M. V. Ryazantseva, V. A. Chanturiya

The paper proposes a new method for selective calciferous separation. The effect was achieved through the application of the combination of high-power electromagnetic pulses (HPEMP) and a specific reagent regime of the flotation. The combined application of HPEMP with the special reagent regime allowed for the improvement of the scheelite floatability: the recovery of CaWO4 rises from 41.2 % (untreated sample) to 58.5 (sample treated at 103 pulses). In contrast, the floatability of calcite decreases significantly: the recovery of calcite drops from 74.7% (untreated sample) to 41.1 % (sample treated at 103 pulses). The conditions were found for the selective separation of the minerals with very close flotation properties. Keywords: Calcite, scheelite, flotation, high-power electromagnetic pulses, DRIFT, XPS

Jan 1, 2020

By R. D. Alorro, B. Tadesse, E. Aghaei

Cinnabar (HgS) and native mercury (Hg) are the most common naturally occurring forms of mercury found in most gold ores subsequently released into the environment during processing. Mercury and its compounds are extremely toxic and recognised as serious health and environmental hazards. This research investigates the possibility of mercury (Hg) removal from waste solutions from gold processing using iron-aluminium (Fe-Al) bimetallic particles. The synthesis of Fe-Al bimetallic particles using zero-valent aluminium and ferric chloride as precursors were performed following the optimisation of influencing factors. The presence of both metals in the prepared bimetals was confirmed by XRD analysis. The experiments for mercury removal by bimetals were designed using the central composite design and Minitab software based on two variables including contact time and adsorbent dosage. The best result of Hg(II) removal (>90%) was achieved using 4 g/L bimetals and contact time of 75 min. However, the statistical analysis of results indicated that these parameters have only a minor contribution to the removal of Hg(II) by Fe-Al bimetals. Higher bimetal dosage and contact time resulted in a higher Fe dissolution from the Al surface which can be attributed to the presence of nitrate (# $) ions in the solution. However, adding 0.1 M NaCl to the Hg solution had a positive impact on Hg removal by improving the conductivity and electron transfer within the solution. The Fe-Al bimetallic particles are promising substances for further testing of Hg removal from gold processing waste solutions with different conditions and constituents. Keywords: Mercury removal, gold processing, Fe-Al bimetals, optimisation

Jan 1, 2020

By B. Friedrich, A. Birich

Gold has been a metal of special importance for mankind for several thousand years. Its outstanding chemical resistance is an important property of this noble metal, but becomes a disadvantage when it comes to gold recovery. The established processes are based on highly aggressive and toxic reagents. Different alternative leaching reagents with a significantly lower toxicity proved to be promising alternatives in the last decades. Major research activities in this field focused on gold ores, so that leaching of secondary resources were not described sufficiently. Based on literature research and extensive experimental investigations, a reagent assessment was conducted for hydrometallurgical gold recovery from electronic waste. It was found that besides thiourea and halides, thiosulfate in particular represents an alternative of major relevance. A variety of different electronic waste (e-waste) specimens were investigated to identify suitable leaching conditions. As a result, an almost complete and selective gold recovery in less than 48 hours from different electronic waste types and components was achieved by thiosulfate leaching. Within the experiments conducted, it was found that the leaching behaviour of cyanide alternative lixiviants differ strongly from leaching of primary ores. Keywords: Gold leaching, cyanide alternative, thiosulfate, electronic waste

Jan 1, 2020

By H. J. Swanepoel, N. B. Strydom

Groups of up to twelve new recruits to the industry were subjected to climatic room acclimatization for either five, seven, eight or nine days prior to being tested for the degree to which they had been acclimatized. These tests were done at 32,2 0C (wet bulb) at a wind velocity of about 0,4 m/sec and the men worked for four hours at a rate of 215,6 kg m/min on one day and at a rate of 431,2 kg m/min on the second day. The results indicated that there is no significant difference between the degrees of acclimatization obtained by the eight- and nineday procedures which confirms the conculsions drawn in a previous report1. The eight-day procedure can thus be claimed to be perfectly adequate and safe. Decreasing the period of exposure to five or seven days would however, not be justified because of the significant differences in physiological responses that were observed on both test days between men acclimatized for these periods and those acclimatized for nine days. It is concluded that it would be unsafe to employ these shorter periods of acclimatization when underground environmental temperatures at which the men are to work, exceed 31 0C (wet bulb).