Search Documents

By F. H. Deist, M. P. Roberts

"The Collieries Research Laboratory of the Chamber of Mines of South Africa is developing a coherent system of programs to aid in the full spectrum of activities arising in the planning of new as well as operating mining enterprises. It is the purpose of this paper to describe the design and application of two subsystems in the complex.One of these subsystems is an initial version of a production simulator. This program draws upon a model of a mining enterprise and simulates the operational and financial aspects of a set of alternative mine production plans.These plans are specified in terms of proposed sequences of operations. Details such as reserves, production rates, resource requirements and so on, are taken from the model.Physically, the model takes the form of a cross-referenced data base, maintained by means of a general file maintenance system which is another subsystem described.The paper concludes with a description and analysis of the first practical application of the two programs."

Jan 1, 2014

By W. Jilowa, C. Nguni, M. Simukoko, C. Nampungwe

The upsurge in cobalt price and demand is propelled by high demand from the electronics and electric vehicle industry. Konkola Copper Mines has cobalt occurring with copper in the ratio 1:10 in ore. The ore is treated in the concentrator and recovered at the smelter as an alloy (Cu 70%, Co 4%–7%, 15% Fe). Subsequent processing of the cobalt alloy is challenging, with very few plants able to treat it, leading to marketing challenges. Konkola Copper Mines sought to improve the cobalt alloy by producing a slag that is easier to handle and process in subsequent processes. Cobalt alloy (3.60% Co, 85.4% Cu) was re-melted in a copper bath four times the mass of the alloy. Silica and lime were added for phase separation and fire refining commenced. Following completion of fire refining and after holding the temperature at 1200°C, cobalt-rich slag was skimmed and blister copper was cast into anodes for electrorefining

Jan 1, 2023

By B. Besa, S. Nalukui

Globally, the demand for mineral products is ever increasing. Extraction of these mineral resources results in the continuous production of a huge volume of waste material, including tailing dumps. The mass of tailings usually exceeds the actual resource and often contains hazardous contaminants. This study investigated the effects of tailings disposal on soil, water, and air quality in the Nampundwe area. Water, soil, and dust samples were collected from different locations in the surrounding communities. The constituents analysed in the samples included copper, cobalt, iron, sulfate, and silica. According to the results obtained, some seepages occurred from the tailings impoundment to the shallow aquifer in the area. However, the general water quality meets the Zambia Environmental Management Agency (ZEMA) statutory limits. Recorded concentrations of sulfate (1500 mg/l), copper (1.5 mg/l), cobalt (1.0 mg/l), iron (2.0 mg/l), and silica were between 0.003 mg/l and 705 mg/l, which is far below ZEMA’s statutory limit. Silica concentration was also evident in the air. The highest concentration recorded was 260 ppcc (particle per cubic centimeter) recorded in July 2019 from the northern direction of the tailings dam. The concentration was below the statutory limit of 350 ppcc. The topsoil from the northern part of the tailings recorded a silica dust concentration of 39.9 ppcc. Iron was evident in the underground soil with a concentration of 8.01 ppcc, cobalt 0.005 ppcc, copper 0.051 ppcc, while sulfate was recorded as 0.41 ppcc.

Oct 9, 2024

By S. Stuurman

Inorganic acids such as sulphuric acid have found use together with certain reducing agents in leaching of copper-cobalt oxide ores. These reagents are not ideal due to the adverse effect the inorganic acids generally have on the environment and the high costs of the reducing agents. In this study a copper-cobalt oxide ore from the Central African Copperbelt was leached in two different environments; sulphuric acid in conjunction with hydrogen peroxide as a reducing agent and tartaric acid. The effects of acid concentration, reducing agent concentration, and temperature were independently determined for both leaching environments. The sulphuric acid concentration was varied between 0.4 M and 1.2 M and the concentration of hydrogen peroxide between 4.0 M and 6.5 M, while the tartaric acid concentration was varied between 0.15 M and 0.35 M. The temperature was varied between 20°C and 50°C. The results showed that the extraction of both copper and cobalt increased with sulphuric acid concentration, reaching a peak at approximately 0.8 M and then decreasing at higher acid concentrations. A similar increase and decrease in metal extraction was observed when the reducing agent was increased. In leaching with tartaric acid, the extraction of cobalt was much higher than that of copper, although extraction of both metals increased with acid concentration. Additions of small amounts of hydrogen peroxide were found to increase cobalt extraction in tartaric acid but had a minimal effect on copper. An increase in the solution temperature had a significant effect in the organic acid environment, with the effect on cobalt extraction being much more pronounced than on copper.

Jan 1, 2014

By A. S. Ratnayake, H. C. S. Subasinghe

In this study, we review the role of mechanical activation in the pyrometallurgical, hydrometallurgical, and electrometallurgical processing of titanium feedstock. Mechanical activation has been shown to decrease the activation energy of chemical reactions, thus enhancing process efficiency and product quality by reducing processing time and energy consumption. Pyrometallurgical processing is energy-intensive and time-consuming. Hydrometallurgy is costly, requires high-grade feed material, and generates toxic waste. Waste generation and process complexity are the major drawbacks of electrometallurgy and solvent extraction. Bioleaching via a mechanically activated pyrometallurgical process can be identified as an alternative method, but the lengthy processing time is the major disadvantage. Mechanically activated titanium concentrate can be used in a finely tuned combined metallurgical process to overcome the challenges and drawbacks in these technologies.

Aug 3, 2023

By J. Talja

Keywords: drying, steam drying, concentrates, copper, lead During the past twenty years steam drying has become a prominent technology for drying of non-ferrous metals concentrate. This is mainly because of its low energy consumption and very low emissions. The first applications of significant capacity were stationary steam dryers, which however, faced severe challenges in maintenance costs and availability. That technology was soon replaced by Kumera?s rotary steam drying technology, which has been the dominant technology in new dryer installations world-wide for the past ten years, ever since the first installation in Hamburg in 1999. There are ten Kumera steam dryers in operation today and five more to be commissioned during 2011. Practically every dryer is different owing to continuous development, new innovations and operational experience with continuous feedback from the operators. Most significant improvements relate to capacity increase with the Kumera steam-dryer family, new feeder systems at the wet end, a completely new design of the dry material discharge with increased availability, heating element design and material selection, and control systems. This paper discusses the modifications and improvements introduced which have enabled the Kumera steam dryer to become the global leader in new dryer installations.

Jan 1, 2011

By J. Engels

CODELCO is considering the implementation of high-density tailings management at the Chuquicamata mine in northern Chile for its long term disposal plan. To achieve this, CODELCO commissioned the design, construction, and operation of a 70 t/d pilot plant, fed by existing tailings. The testing programme was completed in May 2011, and consisted of laboratory rheological and characterization assessments, pipe loop testing, beaching trials, and analyses of deposition behaviour for solid contents ranging from 57?68% (w/w). This paper describes the characteristics of the pilot plant, the testing programme, the beach trial analyses, and the resulting beach profile predictions based on the stream power theory. CODELCO also used other predictive beach slope methods, such as the equilibrium slope concept, which are not discussed in this paper. The final beach profile for design will be selected after an expert analysis of all methods has been completed.

Jan 1, 2012

By D. Fray

Electrochemical processing using molten electrolytes is undergoing a considerable renaissance due to several innovative ideas being explored both in the laboratory and also at the pilot scale. Several of these new ideas are related to developments in energy generation and storage and involve solid electrolytes. Sodium has been prepared by the electrolysis of sodium carbonate or sodium hydroxide with the transfer of sodium ions through a sodium beta" alumina membrane and magnesium oxide dissociated by the removal of the oxygen through a stabilized zirconiaelectrolyte incorporating a fuel cell electrode. By using halides with highly electropositive cations, such as molten calcium chloride, it has been found that the favoured cathodic reaction, when oxygen is present, is the ionization of oxygen and not the deposition of calcium. This approach has been applied to the reduction of many metal oxides including titanium, zirconium, niobium and rare earth oxides and, by using a mixture of oxides as the cathode, homogeneous alloys are produced. This concept can also be applied to deoxidation of solid and liquid metals. Refining of metals is possible using intercalation compounds and, in a completely different application, it has-been found that, by intercalating alkali metals by electrolysis of alkali halides into graphite, it is possible to produce carbon nanotubes and nanoparticles. The technological opportunities of these various concepts will be discussed.

Jan 1, 2004

By M. K. G. Vermaak

Spiral concentration forms a crucial part of gravity separation circuits. The application of process models in the operation of gravity separation circuits offers significant benefits in recoveries and grade control. Significant strides in the modelling of spiral concentrators have been made during the last couple of decades. Despite these advances in modelling techniques and models, application in industrial processes is not fully optimized. The adjustment of splitter positions to accommodate changes in the feed parameters is impractical and difficult, resulting in losses. In this work an optical method is employed to detect the concentrate band position as a function of operating variables. As expected, the results indicate a strong influence of the solids content and total heavy mineral (THM) feed grade on the predicted gangue-mineral interface. Viscosity modifiers indicated the band position to be sensitive to viscosity and therefore the slimes content. Validation on an industrial sample indicated the possibility of using this model in feed-forward control application.

Jan 1, 2008

By A. Butler

This paper explains the politics of mine nationalization in contemporary South Africa. Nationalization and privatization typically occur in the oil, mineral resources, and state utilities sectors, and they tend to follow one another in a long-term cyclical pattern. The paper explains why the current international environment has encouraged demands for nationalization and other forms of ?resource nationalism? in the South African minerals sector. It goes on to describe how the resurgence of resource nationalism has been influenced by internal factional politics in the African National Congress. It concludes that nationalization is unlikely to be the outcome of current policy deliberations within the ANC.

Jan 1, 2013

By D. van Heerden

In the mining industry abrasion caused by both sliding and impact have over the years resulted in costly damage to installations such as ore passes and silos. Good geotechnical practices combined with the use of a high quality abrasion resistant concrete can prolong the life of such an installation and minimize problems associated with abrasion. In order to maximize the life of an abrasion resistant concrete, the choice and combination of the correct raw materials (cement, aggregate and fibre) and overall mix design needed to make up such a concrete are important. This paper presents technical data and practical experience showing that concrete formulated with calcium aluminate cement resists severe abrasion conditions better than similar OPC-based concretes.

Jan 1, 2005

By B. P. Watson

The Bushveld platinum group metal deposits are two distinct, shallow-dipping stratiform tabular orebodies and strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 000 m. The mining method is a variation of planar open stoping. Pillars are widely used to support the openstopes. Little work has been done in the past to determine pillar strength and pillars have been designed using experience and formulae developed for other hard-rock mines. This has led to oversize pillars with consequential loss of ore or undersize pillars resulting in potential collapses or pillar bursts. This paper describes a back-analysis of pillar failures at Impala Platinum, just north of Rustenburg, and provides insights into pillar behaviour. Strength formulae are presented for Merensky Reef pillars at Impala. These formulae may be used cautiously on other platinum mines with similar geotechnical and geomechanical conditions.

Jan 1, 2008

By C. J. Badenhorst

Oxides of sulphur are corrosive and are produced when sulphur-containing fuels are burned. Sulphur dioxide (SO2) is a colourless gas with a characteristic, irritating, pungent odour. Exposure routes to the human body are mainly through inhalation and skin and/or eye contact. Symptoms of exposure to SO2 may include irritation of the eyes, nose, and throat; rhinorrhea (discharge of thin nasal mucous); choking; cough; and reflex bronchoconstriction. To protect employees against the ill health effects of SO2 exposure, they are often required to make use of respiratory protection whenever entering areas were the SO2 levels exceed the statutory limits. The use of respiratory protective equipment should always be a last resort and should be considered only after other control measures have failed to reduce occupational exposure levels to below the occupational exposure limit or whilst other control measures are being investigated or implemented. Whenever the use of respiratory protection equipment is considered, it should always be used as part of a comprehensive respiratory protection plan. It is also extremely important that all potentially exposed persons are adequately and comprehensively informed and trained.

Jan 1, 2007

By R. Shen

This paper presents results of a feasibility study of recycling manganese furnace dust generated in production of ferromanganese and silicomanganese at Tasmanian Electrometallurgical Company, Australia. Dried manganese furnace dust contains about 20 wt% of carbon, in average 33.4 wt% of manganese and 1.3 wt% of zinc. Manganese in the dust is in the form of MnO, Mn3O4 and MnCO3; zinc is mainly in the form of ZnO andZnSO4. Analysis of the zinc balance with dust recycling showed that to keep zinc intake at the acceptable level, it should be partly removed from the dust. In the reduction laboratory experiments, zinc oxide was reduced to zinc vapour by tar of the dust. Reduction of zinc oxide started at 800°C and zinc removal rate increased with increasing temperature; removal of zinc was close to completion at 1100oC. Optimal conditions for removing zinc from the dust include temperature in the range 1000-1150°C, inert gas atmosphere and furnace dust fraction in the furnace dust-manganese ore mixture above 60%. In the sintering of manganese ore with addition of manganese dust in the sintering pot, zinc was reoxidised and deposited in the sinter bed. Removal of zinc in the sintering pot tests was in the range 4-17%. Up to 30% zinc removal was achieved from the bottom layer of the sinter bed. It can be concluded that zinc removal will be low during the processing of manganese furnace dust in the sinter plant. The zinc removal rate will be the highest when pelletised manganese furnace dust is added to the bottom layer of the sintering bed.

Jan 1, 2007

Viscosity measurement was carried out over a narrow range of silica content around the fayalite composition. A wide range of temperature and oxygen potential was covered where the slag was completely liquid. In order to keep the slag composition and the Fe3+/Fe2+ratio constant, theCO2/CO ratio was kept constant as the temperature was varied. Increasing the Fe3+content has little effect on viscosity for slags with a silica mole fraction of 0.31. At higher silica contents, increasing the Fe3+content brings about a small decrease in the viscosity.

Jan 1, 2004

By R. Altindag

Engineers and researchers need to estimate the mechanical properties of rocks from P-wave velocity. In previous studies, the researchers have investigated either the limited values or all the data belonging to sedimentary, igneous, and metamorphic rocks together in the same statistical analysis. In this study, the raw data pertaining to only sedimentary rocks was taken from previous studies and evaluated. For this purpose, a total of 97 samples of sedimentary rock types were subjected to statistical analysis. First, the relationships between P-wave velocity and physical-mechanical properties were investigated by simple regression analysis. All the data were then subjected to multi-regression analysis. Some empirical equations with high correlation coefficients were derived for rock engineers. The equations obtained from the analyses are compared with previous equations found in literature.

Jan 1, 2012

Threshold blasting involves the use of small amounts of high explosive to break and fragment hard rock without having to evacuate mining personnel. The method is easily assimilated and effective in rockbreaking, but requires rigid control on drilling, charging and timing. Current underground trials are aimed at fine-tuning the amount of explosive energy and blast hole geometry to allow the firing of multiple sets of shot holes in a continuous manner. Through correct procedures, the after-blast fumes, dust and fly rock can be contained so as to provide a safe working environment. Threshold blasting hugely reduces the volumes of explosives used in mining and brings to maturity the potential of the process begun by Alfred Nobel when he introduced nitroglycerine, and later dynamite, to mining. Its key contribution is its enabling of continuous mining operations with well understood and relatively low cost technologies. The use of batch blasting, employing large burdens holds the greatest potential for delivering high flow rates of ore at minimal cost. There is good potential for rapid evolution of the concept.

Jan 1, 2002

By S. Michael, T. E. Moongo

Electrowinning consumes a substantial amount of electrical energy, and owing to the ever-increasing unit cost of electrical power there is a need to improve current efficiency in the process. This research was carried out to design a continuous quality improvement framework for improving electrowinning current efficiency by applying statistical process control (SPC) on an online industrial copper electrowinning operation. A sequential mixed research methodology was applied and a statistical software package utilized for analysing data. It was concluded that metallurgical short-circuits (hotspots) had the most significant effect on current efficiency. Bringing hotspots under statistical control resulted in a 5.40% improvement in current efficiency, which is equivalent to approximately 74 t of 99.999% pure grade A copper cathode production over a period of 1.5 months.

Jan 1, 2021

By B. Andresen, S. T. Johansen, H. Tveit, S. Grådahl, B. Ravary

The Norwegian ferroalloy industry has high ambitions regarding environmental standards. Basic research work has been performed to improve the fundamental understanding of ferroalloy processes and the environ-mental aspects. This paper will present work dealing with the understanding of formation and control of NOx, PAH and dioxins. During this work various techniques and methods have been applied, such as comprehensive industrial measurements, laboratory experiments, model development and application of Computational Fluid Dynamics (CFD). The main goal has been to reduce the environmental impact of ferroalloy plants, by means of improving the combustion processes done by introducing new charging routines and optimized furnace operations, instead of installing expensive gas treatment systems. The Norwegian obligations in accordance with the Gothenburg protocol are to reduce the NOx emissions by 30%, compared with the 1990 level within 2010. Measures developed in this work have resulted in 40-60%reduction in NOx emission, and major reductions in PAH and dioxins for ferrosilicon and silicon metal plants. This has been achieved by introducing semi continuous charging and improved furnace operations. Semi continuous charging and optimized furnace operations are shown to reduce the blowing activity (i.e. emission of large quantity of SiO over the charge by direct channelling from the crater zone). It also reduces variation in off-gas temperature and dust production. To understand the processes and to achieve our results we have used online equipment, with fast sample rates and response times, to measure the off-gas compositions and temperatures. Most of the measuring techniques used are based upon optical principles making use of the absorption- and emission spectrum of the gases. In addition a new prototype instrument is developed for continuous measurement of off-gas characteristics, total dust amount and off-gas temperature. The presented work is a result of a long term co-operation research and development teamwork, between the industry and the research community, and has improved both the process and reduced the emissions. The work has introduced new process design and operation standards, and has resulted in ferroalloy production with better environmental standards.

Jan 1, 2007

By A. Drumond, J. F. C. L. Costa, M. G. Lemos, A. L. Rodrigues, F. G. Niquini

The past decade has seen a renewed possibility of using machine learning algorithms to solve a large collection of problems in several fields. Data acquisition for mining operations has increased with the growth in sensor-based technologies, and therefore the amount of information available for mining applications has dramatically increased. Ore sorting equipment is available for separating ore from waste based on differences in physical properties detected by a real-time analyser. The separation efficiency depends on the contrast in these properties. In this study we investigate the application of machine learning models trained using data from the output of a dual-energy X-ray ore sorting apparatus at a gold mine. The particles were first hand-sorted into ore and gangue classes based on their mineralogical composition. Classification models were then used to help decide the balance between the number of true and false positives for ore in the concentrate, with a view to economic parameters, using their receiver operator characteristic (ROC) curves. The results showed AUC (area under the ROC curve) scores of up to 0.85 for the classification models and a maximum reward condition Fpr/Tpr around 0.5/0.9 for a simplified economic model.

Aug 8, 2024