Search Documents

By V. Carabias-Hütter, A. J. Basu

The paper aims at promoting sustainability assessment and reporting into practice using a globally acceptable set of guidelines and a common framework for internal and external reporting at a project/site level. Indicators are used for measuring performance, and this paper addresses development and implementation of performance indicators for sustainability assessment and reporting at local as well as global levels. The selection of a proper set of indicators is a challenging task. The indicators selected should provide the expected information for making right decisions. Relevant and credible sustainability reporting supported by a consistent performance indicator system can be the starting point for benchmarking environmental and social performance for the natural resources sector.

Jan 1, 2004

By Robert L. Bates

The natural separation of one element or compound from others in the earth's crust is a rare geological phenomenon; accumulation of large quantities of a separated substance forms mineral deposits of value. Although igneous and metamorphic processes are effective at times, by far the most significant fractionation is sedimentary. High-silica sandstone, high-purity limestone and dolomite, salt, and anhydrite-gypsum occur in very large deposits and are termed first-order fractionates. The marine diatomite of California, the trona of Wyoming, and the kaolin of Georgia and South Carolina are in deposits of comparable purity but smaller size, and are designated second-order fractionates. The paper considers the various processes and environments in which such industrially valuable deposits were formed.

Jan 1, 1972

By P. Worley

Installation of UP& Is monitoring system was planned to be completed in three stages: Environmental Monitoring, ConveyorBelt Interface, and Power Distribution Interface. With Phases 1 and 2 completed and Phase 3 initiated, massive amounts of valuable information have been obtained. From this information, many benefits where recognized and the decision was made to expand the system. This provided monitoring and control capabilities in a variety of new applications from ventilation fan and pump interface to innovative installations such as ground control monitoring. All current uses as well as future plans for expansion and data manipulation will be discussed.

Jan 1, 1990

By Eric Forssberg, Mats Hallin

INTRODUCTION Evaluation and optimization of mineral processes has been going on since the the first plant started hundreds of years ago. A huge mass of knowledge has been collected since then. The main problem with this type of empirical knowledge of complex processes is that it is very difficult to formulate and document. The methods used for collecting the knowledge is not consistent but-varies with "he person" that does it. In the late 60's and early 70's efforts were made to use computer based techniques to evaluate process performance and to formulate process models for mineral processes. Models were developed, such as the flotation model by R. P. King (1973) which is still used to simulate flotation circuit behaviour. During the 70's. a number of mass balancing packages were developed together with process simulation packages. The industrial sector also made great efforts to develop and utilize computer based systems for process control and evaluation. The expert system that BOLIDEN created in 1974 at the Kristineberg plant was a remarkable achievement considering the hardware (CDC 3600) and the software tools (FORTRAN) available at that time. The main obstacle to successfully implement optimizing computer control of mineral processes was and still is the limited knowledge about the dynamics of complex processes. There are, however. many activities going on in this area today and it seems that the technology is very near a break through. Process evaluation is the most important tool to improve and maintain the optimal performance of a process. Today dedicated computer based techniques are used for fast and reliable screening of the processes. The stages in process evaluation consist of three basic steps: - Data acquisition, manually or by data logging. - Data refining, mass balancing and parameter calculation. - Data evaluation. The refined data can then be used for model construction/calibration and subsequently for process simulation. This paper describes two studies where the techniques mentioned above are used to evaluate and simulate

Jan 1, 1991

By George H. Klein, B. Kent Merritt, Anthony Crisci

During the past decade, over 114-km (71-mi) of 0.25-m (10-in) to 3.7-m (144-in) finished diameter tunnels have been driven below Metropolitan Houston as part of a major program of water and wastewater improvements. This large effort has seen the introduction of midwestern technology with over 18-km (11-mi) of man-entry pipe jacking and European and Japanese technology with over 21-km (13-mi) of microtunneling. Owing to the high water table; a stratigraphy consisting of stiff fissured clays containing numerous layers, channels, and lenses of water-charged sands and silts; and active faults, many challenges existed for designers and contractors alike.

Jan 1, 1991

By Malcolm J. Lake, P. Brad Marchant, Linda M. Broughton

Thiourea is recognized as a technically competitive alternative to cyanide for gold and silver extraction for a variety of ores and concentrates. This paper describes the results of a recent mini-pilot locked cycle test comparing cyanidation with acidothioureation treatment of gold bearing sulphide concentrate. The gold extractability of both methods was similar. The comparative metallurgical operating conditions and test results are summarized. Detailed byproduct solution analyses and environmental toxicity test results are presented and suggest that thioureation might result in acutely toxic byproducts even after treatment. Comparative process economics are summarized based on preliminary commercial operating flowsheets derived for the locked cycle case study. Capital and operating cost estimates are shown. The results indicate that cyanidation is more economically favorable within the constraints of the case study. Considerations for process selection between thioureation and cyanidation, for conceptual case studies, are discussed.

Jan 1, 1998

By David Wright, Colin Burns

Successful leaching of gold depends on appropriate chemical conditions; contact between leach solution and the gold particles; separation of the leach solution from the solids and extraction of the valuable ion from the solution. Irrespective of the leaching method employed the chemical conditions required are similar as is the dependence of solu­tion/gold contact on liberation. The various leaching methods available vary in the means by which gold/solution contact and solid/liquid separation are achieved. The essential difference between heap or vat leaching techniques and those involving agitation of a slurry is dependence on percolation for effective gold/solution contact. The most significant factor preventing uniform percolation is the presence of fines or clays. The quantity and character of the fines fraction is ore type dependent and may result from crushing, degradation during stacking or leaching, or the natural size distribution of the ore. The problems associated with fines can be aggravated during stacking and preparation of the heap. Segregation during stacking can result in concentration of fine particles at the centre of heaps. Further concentration of fines may also occur during irrigation by the movement of the fine particles with the solution. The end result is that the areas in which fines are concentrated become areas of low permeability. The contact between leach solution and the ore in such areas is, at best, slowed down dramatically and, in some cases, prevented altogether. The consequences of this phenomena are slow leaching and a reduction in recovery. The conventional solution to this problem is well known. Agglomeration of ore prior to heap leaching is practised widely. The effect of agglomeration is to immobilise the fines by causing them to adhere either to each other or to larger ore particles. The net effect is that the ore behaves as if no fines were present. The use of agglomeration is limited only by its cost, the most significant components of which are the cost of binding agent, commonly cement, and the capital cost of the agglomerating equipment.

Jan 1, 1995

By Terry McNulty

There are many potential pitfalls in the commercialization of innovative technology, and the failures often are remembered longer than the successes, thereby serving as deterrents to subsequent attempts. Given the dependence of the mineral industry's future on effective innovation, it is essential that we understand the causes of failure. Case histories are presented and the out- comes are analyzed in terms of the driving forces for innovation and the steps taken during development. Industry's current attitude toward and capacity for technological innovation are discussed, and a methodology is suggested for predicting successful innovation.

Jan 1, 1998

By Lane White

Loading shovels are at the heart of most surface mine production. As truck sizes have increased, shovel manufacturers have matched them with larger shovels (see table, page 343). Further increases in shovel size may be in order if trucks in the 270-t (300-st) range find acceptance at the largest surface mines. However, larger shovels are not currently the primary focus of shovel design engineers. Competition and user pressure are combining to keep their work directed toward improved shovel productivity and efficiency. Computer design technology and advanced electronics play an increasingly prominent role in this work. "Improved diagnostic capability, system monitoring, vibration analysis and above all increased user friendliness in machine control systems are being pursued by most manufacturers working in our industry today," observes Stuart R. Cotterill, director of marketing for Harnischfeger Corp. The use of computer-aided design (CAD) systems in shovel design has been in place for many years. However, recent advances in computer capability and improved software programs and graphics are making computers even more useful.

Jan 1, 1995

By Thomas F. Martin, Daniel J. Sieve

In April 1988, the joint venture of Morrison-Knudsen and Paschen Contractors (M-K/P) was the successful low bidder for the Metropolitan Water Reclamation District of Greater Chicago's (MWRD) Contract Number 73-164-2H. This project is yet another in the MWRD Tunnel and Reservoir Plan (TARP) devised to control and treat overflows from combined sanitary and stormwater flows. M-K/P's project, located along the Des Plaines River, consists of 21,569' of tunnel mined to a 35' diameter and two tunnels totaling 14,529' mined to a 12' diameter. All three tunnels will have 12" thick reinforced concrete lining. The path for combined sewer/storm waters to reach the tunnels begins at a connection structure, continues through an approach sewer, a sluice gate structure and down a vertical shaft which is topped by a backflow structure. The purpose of the backflow structure is to prevent water surging to the surface as the system fills rapidly. Backflow preventors represent a change in design after problems developed on earlier constructed portions of the T.A.R.P.. On this project, 14 drop shafts channel flows to the tunnel system. In addition to the drop shafts, contract specifications require an emergency or escape shaft be located not more than 4000 feet from the tunnel headings. Due to long reaches without drop shafts, four access shafts had to be constructed. Thus, the total shafts constructed under this contract will be eighteen plus one 30' finished diameter construction shaft located within Miller's Meadows. Figure 1 shows the overall Des Plaines River System and the M-K/P contract connection to previous and future MWRD projects.

Jan 1, 1991

By Steven G. Vick

Not too long ago a mill superintendent, when asked where his tailings were being disposed, could simply shrug his shoulders and point to the open end of the thickener discharge pipe. This “out of sight, out of mind” approach to tailings disposal is a practice of the past. Today there are very few planned hardrock or energy-related mining facilities where tailings disposal has not been identified as the major area of impact and controversy. In fact, development of some ore bodies has been stymied altogether by lack of suitable sites or methods for tailings disposal. The bottom- Iine result is that tailings disposal often controls the permitting lead time and has a significant influence on construction cost (up to 2070 in some cases) of new minemill complexes. The following article, the first in a series of three, explores technical background and historical perspectives on siting and design of tailings impoundment facilities.

Jan 6, 1981

By Robert L. Sundeen, Richard V. Wenberg

INTRODUCTION Early rock-bolting practice usually consisted of ran¬domly installing bolts, using hand-held drilling equip¬ment such as air-leg mounted sinkers or stopers. As bolting technology evolved, the practice of installing uniform bolt patterns was developed, utilizing random bolt installation as required within the uniform pattern. The uniform rock-bolting technique, when used as the principal method of rock support, requires drills and jumbos designed specifically for rock bolting. This equipment is similar to conventional face drilling machines, except that the jumbos can orient the drills to obtain any necessary bolting angle; often, this means bolts may be installed at or near perpendicular to the centerline of the drift or stope opening. Fig. I shows a typical rubber-tired rock-bolting jumbo of the type commonly used in drifts and room-and-pillar mining. Modern rock-bolting jumbos are capable of drilling the required holes, inserting rockbolts, and torquing them to proper levels. Jumbos also are available for use with resin-anchored bolts. Probably the most unusual of this type utilizes a rotating bolt turret that carries the rock drill, resin charging unit, and the bolt in a single mechanism. Once the turret is loaded with the resin and bolt, further manual effort is not re¬quired. Drilling and bolt placement are accomplished by the operator from a station remote from the bolt site. Fig. 2 shows this turret device. Roof-bolting jumbos are available mounted on rail, crawler, or rubber-tired chassis. Various types of rock drills are used. Depending upon the type of rock, these may include rotary, percussion, or rotary-percussion drills. Fig. 3 shows a typical rail-mounted jumbo. CONDITIONS INFLUENCING APPLICATION General Rock Conditions Rock-bolting generally is applicable in moderately hard to hard rock. No particular type of rock is ex-

Jan 1, 1982

By William F. Riggs

The name of this symposium speaks for itself in the connotation normally assigned to the term 'political. "In this paper, various donors have contributed their stories of metallurgical bloopers, blunders, and scams. The paper covers areas from human error stories, through technical blunders, to outright scams. Included are some stories that involve geology as it relates to metallurgy, warehouses of precious metal concentrates, reagent selection, solutions that treat the symptoms instead of the problems, improper technological transfers, humorous design mistakes in the interest of being exacting, and many more. The stories are all true with the names and dates withheld and the cases presented in the true sense of the "John Doe Stories."

Jan 1, 2001

By Earle J. Klohn

Tailings disposal has rapidly become an area of increasing importance to both existing and planned mining operations. In recognition of the significance of this topic, MINING ENGINEERING is presenting a series of articles on tailings disposal. The first, published in June, outlined some site criteria that influence tailings disposal and some of the design options available to meet these criteria. The following article explores in more detail important design criteria for tailings dams and provides several case study illustrations.

Jan 7, 1981

By J. A. Herbst

Successful transitions from micro- to macro-engineering are the keys to effective technology transfer between research and development organizations and industrial end users. At the same time, it has proven to be one of the most difficult tasks that the minerals industry has had to manage. Typically, developers of fundamental information concerning how mineral processing subsystems work have been academics and government scientists. These are the individuals giving the most important input to micro-engineering models that can benefit industrial operations. Publication is the usual route for "attempting" to transfer this technology to the end users. Unfortunately, with such publications, very little direct communication occurs concerning real industry needs or the future steps required to make the particular micro-engineering model useful. In the past, the industry has relied on in-house R&D groups and plant metallurgists to "translate" publications, to provide useful macro-engineering tools for plant applications. To some extent, engineering companies have also been asked to serve this function. However, these firms have been rather ineffective in this area since their conservative nature has caused them to look rather suspiciously at new technology. This approach to technology transfer has worked, albeit clumsily, for the last several decades. This communication system is now on the verge of total collapse due to conditions of the minerals industry. Mining companies can no longer afford the significant overhead expenses of specialized technical staffs. Universities are finding it extremely difficult to interest US students in mineral engineering programs, and funding for such programs is weak. Faculty members involved in micro-engineering research today tend to focus on pure (non-application-oriented) research.

Jan 1, 1992

By Gregory A. Vaka

Robins Engineers & Constructors, Inc. as the exclusive U.S. licensee introduced the PIPE CONVEYOR to the North American marketplace early in 1984. The sale of the first PIPE CONVEYOR in 1985 was a difficult task since the conventional troughed belt conveyor was the accepted and the most widely used means of continuous transportation of bulk materials handling in the world. Initially our clients viewed the PIPE CONVEYOR as a departure from the normal and accepted form of material handling. Since then, the parent company of Robins Engineers merged with Krupp of Germany to form KRUPP ROBINS, INC. in the United States. To date there are over 462 PIPE CONVEYORS operating worldwide with the majority of the long overland systems designed and installed by Krupp Robins, Inc. The PIPE CONVEYOR is now becoming the norm, viewed by those who are familiar with its capabilities as the preferred method of transportation for all bulk solids.

Jan 1, 1997

By C. P. Mangelsdorf

Introduction During the 13 years since C. C. White introduced the Birmingham roof truss there has been a revolution in permanent roof support technology. While not all of the emerging concepts have their origins in the truss-resin bolting is a prime example - the combinations and permutations of devices presently available to the underground mining industry reflect a well-spring of creative activity. The purpose of this report is to chronicle a number of roof support system that have same physical similarity to the Birmingham truss, and to report on their application. Definitions The application of the tern "truss" to the device developed by White of the Birmingham Bolt Company in 1967 may be derived from the classical technique of stifwood, by the attachment of an underslung, sometimes pretensioned metal strap, rod or cable. If the beam is separated from the reinforcement by a single block or vertical post it is called a "King's Post Truss". If two equally spaced blocks or posts are used it is referred to as "Queen's Post". When the immediate roof of a mine is visualized as a beam, the Birmingham device completes a structure resembling this latter form.

Jan 1, 1982

By S. C. Suboleski

Underground long-range planning and mine design is an iterative process beginning with a specified production level, quality criteria, and geology of the deposit. Given these factors, face equipment is selected, the number of units needed and production per unit are calculated, and the mine infrastructure needs are developed. The scheduling of units then follows, with the design of the various support systems coming next. The support systems needed to maintain production can be grouped as follows: (1) outby haulage of mined material, (2) supply and manpower haulage, (3) ventilation and associated environmental considerations, (4) drainage, fresh water, and related considerations, (5) rock mechanics, and (6) power, supply. Thus, long-range planning may be viewed as a three-tiered structure, with the data on required production, product quality, and geology at the upper level; the development of face production capacity and the scheduling of units sufficient to meet the needs of the first two at the second level; and the development of support operations for the production units at the third level. Changes at any level may affect not only the items on that tier but may also cause a change to the items on the tier above and below. For example, if the rock mechanics data indicate that desired opening sizes will not be stable, then this situation will affect not only the ventilation design but also the production rate and possibly the selection of equipment itself. These, in turn, may affect the scheduling of units and the number of units, ultimately influencing the entire third tier of systems.

Jan 1, 1979

By A. S. Henderson

Eastern Mesabi taconite is one of the hardest rocks known, but fortunately it shows little tendency to pack in the crushers, when the minus 5/16 inch material is removed. The crushing circuit is essentially as shown in the Engineering and Mining Journal article, "Reserve's New Taconite Project", dated December, 1956 except that the grizzly screen between the two stages of gyratory crushing has been eliminated. The Reserve operating staffs aim is to utilize the crushing equipment in such a manner that the maximum tonnage of taconite can be crushed to the required size at a minimum cost. As is readily apparent, the primary consideration is to produce a desired size product, with the other operating factors to be balanced, thus achieving the best setting for each crusher. Much effort has been expended toward the development of a satisfactory sized material for feeding the rod mills. The characteristics of this feed must allow the following situations to be handled by the existing equipment: 1. The material being fed to the rod mill must be such that it can be fed into the unit with the proper quantity of water to maintain the correct density within the mill. 2. The rod mill must produce a product from this feed which can be handled without difficulty by the magnetic cobbing and ball mill circuit. 3. The incidental tramp must not exceed that quantity which can be handled easily after the rod mill and after the ball mills.

Jan 1, 1959

The Chinese city of Shanghai is one of the fastest growing in the world. To keep up with the growth, two tunnels, three-lanes each, are being built beneath the Yangtze River to connect Shanghai with the Changxing River Island. To complete such a large project, Herrenknecht Tunneling Systems was brought in to construct the largest tunnel boring machine (TBM) in the world. The first Herrenknecht S-317 Mixshield has a diameter of 15.43 m (50.62 ft). It was built to construct one of the two 7.2-km (4.5-mile) tunnels. The tunnels are part of the Changjiang Under River Tunnel Project and will be at depths of up to 65 m (213 ft) beneath the Yangtze River in Shanghai-Pudong. These two tunnels are to be opened to traffic in April 2010, in time for Shanghai to host the World Expo. More than 20 million people live in the Shanghai area. The area itself has been growing at an extremely rapid pace for more than a decade and is in need of more space. The search extended beyond the natural limits of the Yangtze River Delta. As part of its incredible growth, 500 new vehicles are registered every day. The new tunnels will connect the Changxing River Island, with a population of approximately 600,000 people to the road traffic network. A bridge construction will also provide a traffic link between Changxing Island and the large island of Chongming.

Jan 1, 2007