Search Documents

By David J. Herzog

There are two steps in evaluating potential mine waste impacts on ground and surface waters. Characterize the mine waste (characterization methodologies) and assess potential impacts (assessment strategies). One or both may be required for mine permitting, operation and closure. The first step is to characterize the waste. Determine if it has the potential to release chemical constituents or acid rock drainage to the environment. If no potential exists for release to the environment, the evaluation process is complete. A monitoring plan is then established. If the potential exists for release of chemical constituents or acid rock drainage to the environment, a strategy to evaluate potential impacts must be implemented. Strategies discussed here to evaluate potential impacts were developed during investigations at precious metal and base metal mines in Nevada. Water resources in Nevada consist mostly of ground water. So the strategies discussed focus on potential impacts to ground water. However, several of these strategies also apply to assessing potential impacts to surface water. Implementing these strategies has helped determine the potential for impact and has been successful in permitting mine expansion as well as allowing continued operation and obtaining mine closure at several mine sites in Nevada. These strategies were carried out in accordance with Nevada Division of Environmental Protection (NDEP) regulations and through the National Environmental Policy Act (NEPA)

Jan 1, 1995

By D. Farahmand

This paper focuses on formulating a practical procedure for forming long-range production and development schedules in underground mining. A computer program developed to be run on a microcomputer is presented and discussed in detail, and a practical case study is analyzed to demonstrate the suitability of the procedures discussed in the paper. The intent of the computer scheduling model is to have quick access to vital information when changes in development and production are under consideration by management.

Jan 1, 1986

The feasibility of exploiting a mineral deposit by developing a surface mine is closely related to the environmental protection and land reclamation costs. This issue has utmost importance for West Macedonia Lignite Centre (WMLC) of Greece, where there is still a lot of interest for opening of new mines and for further development of the existing open-pits. The decision-making process in these cases can be based on a decision tree that takes into consideration the various cost components of environmental management, the alternative solutions, the environmental permits and the cost reports of environmental management actions carried out so far. Moreover, the mine planning procedure is affected indirectly by numerous uncertain environmental and socioeconomic parameters, such as the delays caused by the bureaucratic procedures and the settlement of arguments in the Court.

Jan 1, 2006

By Jugal Kar

Yilgam Star treats a gold bearing ore which has an association with pyrohotite and pentlandite (Fe,Ni)9S8 Nickel behaves similar to gold in cyanide solution, it leaches in cyanide to form a number of species. It adsorbs like the noble metals on carbon. During smelting Nickel causes significant problems in the crucible as the melting point of nickel is much higher (1452 °C) than gold (1040 CC). The crucible became overheated, holed and increases furnace downtime. To overcome such dif­ficulties an investigation was carried out to reduce the amount of nickel on steel wool during stripping. Yilgam Star has got I.P.S. high pressure zadra stripping system which works on 400 kpa, at 140 °C. The trend of gold and nickel profiles has been observed with varying caustic concentrations. The gold and nickel profile has been monitored with the addition of cyanide in the stripping liquor. It has been ascertained that at lower caustic levels the nickel ion remains in solution and is subsequently not electro­won. The cyanide concentration of0.4% (Wt/Vol) keeps nickel ion in solution and induces metallic nickel to produce nickel ion as NiCN.

Jan 1, 1995

By J. G. Groppo, T. L. Robl, C. J. McCormick, W. M. Lewis

The combination of froth flotation and hydraulic classification can facilitate the production of a high-quality pozzolan that meets or exceeds ASTM specifications. This combination has been rigorously evaluated and results of pilot-scale testing are presented. Pilot-scale testing was conducted on fly ash from two active electric utility storage ponds. The tests demonstrated that a high-quality and consistent pozzolan could be produced using Advanced Pozzolan Technologies' Fast Float™ Process. Along with the pozzolan, the additional production of aggregate for masonry mortar and the production of a low sulfur, medium-Btu fuel were also demonstrated. The Fast Float™ Process incorporates several simple unit processes to ensure pozzolan consistency. Classification controls the particle size distribution, which is critical for achieving early strength;flotation controls the grade with respect to L.O.I.; and dewatering controls the moisture content.

Jan 1, 2000

By M. Carvalho, R. Bicallho, M. Queiroz, R. Gomide, V. Silva, R. Toubes

Since it is becoming increasingly important, from an environmental viewpoint, to minimize blast vibrations induced in urban dwellings and improve rock fragmentation in order to reduce costs with loading, transportation crushing and grinding, a cooperative research project was established between Companhia Vale do Rio Doce - CVRD and the Blasting Research Group in the Department of Mining Engineering at Escola de Minas - UFOP to investigate which elements interfere on ground vibration, air blast, flyrock and rock fragmentation related to rock blasting activities at Conceição Mine, located in Itabira city, state of Minas Gerais, Brazil. This research also involved development of a new explosives formulation in order to minimize the total blasting cost. This paper presents the general scheme of the research running from May 1995 to May 1997 and a summary of the results obtained in the field tests that were carried out in this mine.

Jan 1, 1998

By I. Dunlop, A. Goulsbra, R. Dunne

Mineral liberation or more aptly the particle size at which cost effect liberation is attained is an important mineral processing parameter. This implies that not all the mineral is liberated as further size reduction is not economically warranted. For ores of low grade minimising both the comminution capital and operating costs are crucial aspect to ensure project visibility. As a consequence the focus of attention for the most part is direct­ed to 'coarsening the grind" ahead of any downstream process­ing treatment. In most cases, recovery will be sacrificed to pro­vide for 'more tonnes' of capacity and in general this is eco­nomically justifiable. Preferential liberation and its measurements is an aspect of mineral processing that has created much attention and contro­versy. It is not the purpose here to discuss this matter in depth other than to state in broad terms that if an ore from the same source is subjected to comminution by two different methods, such that the product particle size distribution is similar, and subsequent downstream treatment demonstrates substantial dif­ferences in recovery, then there is reason to believe that prefer­ential liberation has occurred. Comminution by high pressure grinding rolls (HPGR) is a relatively new technology claimed to have two major advan­tages over conventional comminution. Firstly and more impor­tantly is the ability to improve comminution power efficiency. Power reductions of 10 to 40 percent being claimed. (Pagett et al (1995), Sargent (1995)). A secondary benefit claimed is that preferential liberation can occur. Generally, for HPGR there is a natural tendency of the product to have a skewed particle size distribution to the finer size. This in its own right could manifest itself in improved leaching and preconcentration performance. The question remains that if in using another comminution device, other than a HPGR, to produce a similar product size distribution as the HPGR, will there be any difference in downstream between the products from this and a HPGR.

Jan 1, 1996

By Ronald B. Gabitzsch, Norbert P. Hanke

During 1982, record advances have been achieved in the excavation of vertical shafts with a V-Mole (a vertical shaft boring machine). The V-Mole, supplied by Wirth GmbH in Erkelenz, West Germany, has been used in West German coal mines since the early seventies, mainly for the construction of internal shafts. In 1981, it was brought into the United States for the construction of a series of ventilation shafts with depths varying between 512 m (1680 ft.) and 622 m (2040 ft.) excavated to 7.0 m (23 ft.) diameter. These shafts were needed for the development of coal mines for Jim Walter Resources, Inc. in Brookwood, Alabama. After a description of the mechanized shaft excavation system with the V-Mole, the conditions and parameters, such as ground, shaft dimensions, and linings are discussed. These factors are important considerations for a technically and economically feasible utilization of the V-Mole. In addition, the advantages and disadvantages of using the V-Mole technology in comparison to other shaft construction methods are evaluated.

Jan 1, 1983

By A. N. Islam, C. Simons, M. N. Hughes, J. Barrett

The effluent from the bio-oxidation of arsenopyrite contains high concentrations of iron(III) and arsenic(V), the pH being in the range 1.0-1.3. The use of lime to increase the pH causes the precipitation of calcium sulfate, calcium arsenate and a mixture of solids containing calcium, iron and arsenic. The presence of calcium is due to slaked lime encapsulated by the iron arsenate precipitates. These iron arsenate solids are related to known minerals. The use of sodium hydroxide to effect the precipitation of iron and arsenic produces solids which are more stable than those produce by using slaked lime. The use of limewater produces an initial precipitate of calcium arsenate.

Jan 1, 1991

By J. R. Montgomery, T. A. Phillips, F. Blackham, D. J. Adams

Underground water, whether it is a mine seep, in situ leach solu­tion, or a pollution plume, is difficult to track and monitor. Monitoring wells are costly to drill and may be placed in the wrong spot. This report describes a test of an electromagnetic technique to track acid water draining from the Midnite Mine near Spokane WA. The tests successfully mapped the path of acid mine drainage being collected at the mine from two seeps. Several small side branches flowing to smaller seeps and a mix­ing zone where relatively clean water mixed with the acidic water, were also mapped. The study has changed previous opin­ions on the flow of water through the site and will be used as a basis for future site remediation planning.

Jan 1, 1996

By Waclaw Trutwin, Stanislaw Wasilewski

Application of computer-based systems for ventilation process monitoring makes it possible to widen the system functions with those connected with long-term data analysis. It allows the mine ventilation engineer to carry out necessary preventive actions. In future the wide application of computers and sophisticated expert systems together with automation equipment (like remotely controlled regulators and fans) will allow to gradually introduce minewide systems for air flow control. To achieve this goal research work is carried out using data from a mine ventilation monitoring system and methods of computer analysis of time series. With the use of digital filtering the measuring signal spectrum has been divided into three subranges components of which are important with regard to various needs of mine ventilation staff as well as to monitoring and control system functions.

Jan 1, 1991

By M. W. Rutland, E. Manev, R. J. Pugh

Data collected from several different fundamental surface chemical techniques were compared to study the interfacial interactions in the dodecylaminelmica flotation system. In the present study, the method used was the microinterferometric free foam film technique of Scheludko (1967) in which the stability, thickness and interfacial potentials at the air/dodecylamine solution interface were determined. These results were compared to previously published data, obtained from surface force measurements (Rutland et al. 1992), in which the interaction and hydrophobic adhesion (pull-off force) between molecularly smooth mica sheets in the amine solution had been reported. Also equilibrium contact angle measurements were used for comparison. The data was collected over a range of pH values and related to the batch flotation response of mica in dodecylamine solution. It was found that maximum flotation occurred at pH 8, but this did not correlate with the minimum in double layer interaction potential. However, it appeared to correspond with a tightly packed collector monolayer giving maximum hydrophobicity to the mica surface. Finally, from the extended DLVO theory, it was shown that heterocoagulation between the bubble and the mica could only occur, providing there was a very long range hydrophobic interaction force to counterbalance the repulsive van der Waals and electrostatic forces.

Jan 1, 1995

By Jean Paul Duterque, Morris J. V. Beattie

In many parts of the world, pyrite and arsenopyrite occur together in sulphide ores either as the only sulphide minerals or in conjunction with other valuable sulphides. It is desirable to produce separate concentrates of the various sulphide minerals, including pyrite and arsenopyrite, so that the contained desirable metals can be recovered economically. It is common, for instance, for gold in an ore containing both pyrite and arsenopyrite to be associated almost exclusively with the arsenopyrite. It is desirable in this instance to produce an arsenopyrite concentrate for gold recovery while rejecting the barren pyrite.

Jan 1, 1992

By Jacques Monette

Gold and silver cyanide complexes are presently desorbed from activated carbon by means of hot caustic elutions. These solutions may or may not contain additional sodium cyanide. There are several parameters which affect the rate of stripping. Some of these include pH, ionic strength, and tempera­ture. Stripping is conducted in recirculating (ZADRA) or once through (AARL) circuits. This paper describes the development of a new chemical eluant which increases the rate of stripping of both gold and silver cyanide complexes from carbon. Two case history applications are described.

Jan 1, 1995

By K. R. Johnejack, R. Quintanar, P. Lapointe

Chino Mines Company has investigated effects from historical mining to sediment along Hanover and Whitewater Creeks. Concentrations of metals were statistically stratified for risk assessment. Stratification by size was more prevalent than by depth, with concentrations higher in the fines. Concentrations with depth were mixed, but overbanks showed more stratification with higher concentrations in the surface. Members of a geomorphic feature type generally were not stratified. However, geomorphic features were stratified by type, with the active channel and bars being the most alike and the overbanks being the most different. Only a few metals showed decreasing concentrations with distance downstream.

Jan 1, 2002

By J. Finch, W. Petruk, R. G. Pinard

An investigation was conducted to determine the minimum number of samples that must be studied by image analysis of polished sections to characterize a mill product and determine the apparent mineral liberation. It was found that a representative polished section cannot be prepared from an unscreened sample that has a wide size range of particles. Similarly, individual screened fractions are not representative of the sample because minerals are partitioned during screening, and the quantities of soft brittle minerals are increased in fine grained fractions, whereas the quantities of hard minerals are increased in coarse grained fractions. It is assumed that results obtained by combining data for a series of narrow size range screened fractions (one Tyler size range) are representative of the sample, and relatively accurate apparent mineral liberation data can be obtained for a mill product by analyzing each fraction and combining the data. Somewhat less accurate data would be obtained by analyzing a series of screened fractions that have a wider size range of particles (five Tyler size ranges).

Jan 1, 1987

By Robert A. Jankowski, John J. McClelland, Charles Babbitt

The purpose of this study was to develop guidelines to enable mine operators to maximize longwall dust reductions, while optimizing the use of ventilating air and shearer water consumption. A recent investigation by Foster-Miller Incorporated, under a Bureau of Mines contract, quantified the effect of increased face airflow and shearer water supply on face dust concentrations. A 70 pct reduction in respirable dust levels was achieved at the shearer operator's position during tail-to-head cutting by an incremental increase in average face air velocity from 83.8 m/min (275 fpm) to 123.4 m/min (405 fpm), while holding shearer water consumption constant. A 60 pct reduction was achieved through an increase in shearer water pressure and flow from 9.1 kg/cm2 (130 psi) at 0.19 m3/min (50 gpm) to 19.7 kg/cm2 (280 psi) at 0.28 m3/min (75 gpm), holding airflow constant. The combined effects of increasing both parameters produced an 85 pct reduction. Optimal usage of ventilating air and shearer water consumption can be achieved by defining a "point of diminishing returns" above which further increases no longer reduce dust concentrations, proportionately .

Jan 1, 1987

By Jim V. Rouse

The decision to hold parallel conferences dealing with hazardous waste and mining waste grew out of the conviction that there were advantages to having personnel serving the two groups talk to each other, as both groups develop cost-effective and environmentally-protective solutions to present and future waste-disposal problems. There has been a certain amount of "reinventing the wheel" which could have been avoided by a better dialog between the two groups. The intent of holding the two parallel conferences is to allow for networking, to minimize future needless redundant effort. The opening session panel speakers represent expertise from both industries; I feel honored to speak as one with a history of serving both groups as a specialist in the subsurface behavior of heavy metals.

Jan 1, 1991

By A. John R. Hart

INTRODUCTION The use of precast concrete tunnel liners as the initial and final tunnel lining for transit systems has been a major consideration of designers for over three decades. The obvious benefit of building a tunnel that requires only a single pass in constructing the structural lining can provide the opportunity of saving both time and cost. This technique has had worldwide application in transit systems in London, Munich, Hong Kong, Toronto to name a few. In the United States precast liners were evaluated for use on the BART System in San Francisco in the early 1960's but did not provide sufficient confidence in the sealing capabilities available at that time. In 1976 it was decided to call for bids on the Lexington Market Tunnels in Baltimore with a precast concrete liner alternative for one of the tunnel drives. This option was selected by the owner and UMTA to provide a study evaluation for the benefit of the industry. HISTORY In 1983 Washington Metropolitan Area Transit Authority began calling for a series of bids on soft ground tunnels on the Green Line, which included the option of using precast concrete tunnel liners first as an alternative to fabricated steel tunnel liners. Over the years following, the precast concrete tunnel liners have become known as the conventional tunnelling system and, in the last year,

Jan 1, 1989

By J. J. Scott, G. H. Bennett

INTRODUCTION Friction Rock Stabilizers, commonly called Split Sets,tm* have been under development since early 1973. Five years of intensive laboratory and field testing led to their introduction to the metal mines in the United States in the fall of 1976. Actual sales started in February of 1977 and, to date, over five million units have been marketed to metal mines. The present rate of useage is near 3 1/2 million units per year which is approximately 50 per cent of all roof fixtures used in the United States metal mining industry. Mr. Richard Hoppe, Senior Editor of Engineering & Mining Journal, in an article of the February, 1979, issue, entitled "Winning the Battle Against Bad Ground", said, "In hardrock mining operations in the western U.S., particularly underground uranium mines where exceedingly difficult ground is common, no roof support system has been accepted more quickly than the Split Set friction bolt invented by Dr. James J. Scott and developed by Ingersoll-Rand Co." This paper describes how Friction Rock Stabilizers function and presents technical data to show the uniqueness of the Friction Stabilizer system. SPLIT SET STABILIZERS The Split Set System is a revolutionary development in the field of ground control. The system produces an interior reinforcement to a rock mass which: *Trade Mark of Ingersoll-Rand Co.

Jan 1, 1979