Search Documents

By A. M. El Shafey, Ahmed W. Hussein, Ibrahim M. Gaafar, Mona M. Fawzy, Mohamed Diab, Mohamed S. Abu El Ghar

The Quaternary stream sediments of the Diit area, southern Red Sea coast, Egypt, were mineralogically studied for their content of economic heavy minerals. The study area covered approximately 450 km2 and included three main parts: Wadi and Delta Diit, as well as Diit lens. The mineralogical investigation revealed that these sediments contain considerable amounts of placer ilmenite, magnetite, zircon, sphene, apatite, garnet, and rutile. Also present, in minor or trace amounts, are uranothorite, monazite, xenotime, fergusonite, khatyrkite, and gold. The magnetic fractionation tests, supplemented with the XRD and SEM mineral analyses, indicated the presence of Fe-oxide minerals as wuestite, hematite, and maghemite accompanied with magnetite as products for hand magnet separation. Ilmenite separation was carried out using a high intensity magnetic separator at a current of 1 A, while the paramagnetic minerals (e.g., garnet, pyroxene, amphibole, epidote, monazite, xenotime, and fergusonite) were separated as magnetic fraction at a current of 3 A. The non-magnetic minerals (e.g., zircon, apatite and rutile, uranophane, uranothorite, gold, and khatyrkite) were obtained at 3 A current. On a mineralogical and geochemical basis, the present work suggests that Diit stream sediments should be considered as a potential source for Ti, Fe, Zr, Zn, and Cu after the physical upgrading processes for concentrating the minerals carrying the aforementioned economic elements.

Jan 21, 2022

By E. L. Smith

The development of larger size flotation machines, which started in the 1950's and 19601s, is still proceeding. The largest mechanical flotation machines available today have unit volumes in the range of 38 to 42 m3 (1,350 to 1,500 cft). In fact, the motivating forces of increasing capital and energy costs and decreasing ore grades, which created the need for large flotation cells, not only still exist, but are becoming more critical. This paper reports the development of an improved mechanism for these large flotation machines. The starting point in the development of a new mechanism was the identification of design and performance features of existing machines where improvements were desirable. The result of this work was a mechanism which is an improvement over existing designs. This new design is characterized by an efficient overhung stator and a vortex profile rotor. The overhung design of the stator removes unnecessary and undesirable baffling in the lowest parts of the tank, while maintaining a quiescent froth layer. This results in lower power consumption and better pulp circulation and solids suspension. The vortex profile rotor acts as an efficient pump, with higher pulp recirculation rates as evidenced by the increased air dispersion capabilities, good solids suspension, and low power consumption.

Jan 1, 1982

By Yi Luo, Jian Yang, Hua Jiang

Surface subsidence events induced by underground longwall coal mining operations can cause various disturbances to surface structures ranging from integrity and stability to functionality problems. Highway bridges, as a kind of special road construction that can only tolerate smaller movements and deformations than road pavements, are particularly susceptible to severe influence caused by subsidence-induced ground movements and deformations. However, based on accurate subsidence prediction and correct influence assessments, efficient and effective mitigation and remediation measures can be designed and implemented to ensure the continuous service of bridges, safety of the travelers and smooth mining operations. In this paper, based on the predicted final and dynamic surface movements and deformations, the techniques to assess subsidence influence on the integrity, stability and functionality of bridge structures (e.g., decks, beams, abutments, etc.) are presented. A number of mitigation measures to protect the bridge structures are recommended along with an actual application case.

By R. Kent Comann

Introduction This article describes ways to maximize employment potential for those looking for a job in the minerals industry. Advice on the right way to prepare a resume is followed by tips on where and how to look for a job and ways to make the best of an interview. Information on current salaries is also included. RESUME NAME: Give home and college addresses and telephone numbers, ADDRESS: if still in school. Otherwise, give home address and TELEPHONE: telephone plus business telephone number. JOB OBJECTIVE: What do you want to do? EDUCATION: List degree(s), name of college(s), location(s), and date(s) degree(s) received or to be awarded. Do not list your high school but do include postgraduate education, training, or seminars. WORK EXPERIENCE: List your most recent experience first, and the rest in reverse chronological order. Include dates (month and year) and company names. First show the entire time spent with each employer, then list the various jobs (with dates and duties) you may have had with this employer. MILITARY SERVICE: List dates, branch of service, and duties. If you did not serve, delete this section. COLLEGE ACTIVITIES: Show organizations, sports, and offices held. Only list these if you are a graduating senior, otherwise delete this section. PERSONAL DATA: List age, marital status, height, weight (optional), foreign languages spoken, professional memberships, and health (if good or excellent, otherwise do not mention it in the resume). If you prefer a certain location and would not accept a job anywhere else, list the location desired. Otherwise, do not restrict yourself. Also list special skills, hobbies, or interests that will help sell you to the company. Be brief in this section and use good judgement as to what you say. REFERENCES: Furnished on request. Resume Guidelines There are some things to remember when preparing a resume. These include: • Limit your resume to one page, unless you have a lot of experience. Then it should be a maximum of two pages. • Use 8.5 x 11 plain bond paper, white or off-white. Stay away from colored paper, odd size paper, and cute resumes. They are counter-productive. • Make certain your resume is typed professionally. Be sure to check for spelling, grammar, and typographical errors. • Have your resume reproduced by copier or printing shop. Do not use carbon copies. • Keep your sentences and remarks short and punchy. Use action verbs. • Have a good layout that is easy to read, brief, and uncluttered. Allow some white space in your resume. There are also some things you should not do when preparing a resume. These include the following: • Do not include a photograph or mention your religion, race, or sex. • Do not leave gaps of time unaccounted for in your resume. • Do not include your college transcripts with your resume or list all the courses you took in college. • Do not list all the articles you have written. Only list one or two, if appropriate for, say, a research and development job. • Do not include reference letters with your resume. Any good, prospective employer will make telephone reference checks. • Do not use "Curriculum Vitae," use "Resume." • Do not include unnecessary data such as your social security number, passport number, or PE registration number. If you are a PE or EIT, be sure to mention that in your resume. Do not mention US citizenship or US work permit unless you have a foreign education or are not a native US citizen. • Do not include present salary or salary requirements. This will come out in the interview. • Do not use the word "I" in your resume or refer to yourself in the third person. • Do not lie, distort, exaggerate, or editorialize in your resume. • Do not have your resume prepared by an outside resume service. This is unnecessary, costly, and generally not effective.

Jan 2, 1985

By Michael J. Miller

The demand and supply of wollastonite has gone through a dynamic period in the 1990's. A 10% -15% growth rate of demand stimulated interest in evaluating new projects. However, the mid-1990's brought declining prices for commodity applications and natural barriers to entry for technical applications, making many of these potential projects uneconomic. Successful projects that were brought to market were done so by incumbent producers. This work examines the competitive structure of the wollastonite market by evaluating the strategic decisions of the industry leader, NYCO Minerals Inc., and a new market entrant, Orleans Resources, in an attempt to identify the environmental threats and opportunities of this industry. Results suggest new entrants like Orleans Resources face significant entry barriers for technical applications, while NYCO Minerals could improve its profitability by having less exposure to commodity applications.

Jan 1, 1999

By C. R. McKee

In-situ mining of hard rock deposits will only become successful as we understand the engineering parameters involved and the design limitations they impose. As recognized by Wadsworth1 the most critical area is the enhancement of permeability in a hard rock mass. Along with creating permeability, the appropriate flow and fragment size conditions must be generated to insure economic rates of mineral recovery. In this article our interest is confined to true in-situ processes in which boreholes are drilled from the ground surface or a mine drift to deeper strata. We assume that fractures and permeability enhancement will be due to explosives detonated in boreholes. Other techniques such as hydraulic fracturing do not produce the necessary size distribution to promote economic extract ion rates unless the medium is already highly fractured and interconnected. Notable exceptions where hydraulic fracturing is applicable are many oil, gas and salt deposits. For many in-situ processes, an array of explosive charges offers the opportunity of creating a distribution of many fractures not achievable by other techniques. Such a situation would be suitable, for example, to in-situ mine hard rock gold, uranium, copper or oil shale deposits and may enhance oil and gas recovery in certain situations. The purpose of our article is to review and extend the explosive permeability theory of McKee and Hanson 3,4,5 and to apply its results to derive design parameters suitable for in-situ mining.

Jan 1, 1981

By Verya Nasri, James Sullivan, Alex Varas

"INTRODUCTION Many major cities in the United States have a combined storm water and sanitary sewer network. Regular rainfall overwhelms the system capacity and results in millions of cubic meters of untreated sewage being dumped into local waterways. One legally mandated solution includes several kilometers of large diameter shallow or deep rock or soil tunnels, a pump station as well as associated collection sewers, diversion structures and drop shafts. In this paper, the basis for design of different system elements including the drop shafts and pump station is explained in detail. Common construction methods used for different type of shafts including tangential vortex and baffle plunge, and also pump station alternatives comprising cavern or various shaft configurations are discussed. DIFFERENT TYPES OF PUMP STATIONS The dewatering pump station serves as the heart of any deep CSO tunnel system and is critical to the goal of reducing CSOs by providing a controlled release of the stored tunnel volume to the wastewater treatment plant. As the major mechanical component of the project, the station will require the greatest attention by operations and maintenance staff. Designing a durable and easily operated pump station requires addressing some major challenges, including the following: • Longevity – equipment, materials of construction, and station environment • Controlling odors • Safety for operators and maintenance personnel • Easy access to equipment • Protection from hydraulic surges Location. Owners face a fundamental decision relative to the location of the pump station, which will affect how these challenges are addressed. The pump station can be built within the tunnel launch shaft or within its own dedicated shaft. This decision is driven by cost and schedule. Use of the tunnel launch shaft may provide owners cost saving opportunities by not having to construct a separate pump station shaft. However, this will likely extend the pump station construction as much as two years until the tunneling has been completed. Furthermore, delays to the tunneling operation would delay the pump station construction work, potentially leading to delay claims. For this reason, it has been more common to utilize a separate pump station shaft on recent CSO tunnel projects (Nasri et al. 2015)."

Jan 1, 2016

By K. V. Raj, R. Jacksha

Conveyor systems persist in being a source of injuries and fatalities in the mining industry. To reduce these incidents, better methods are needed to enhance the monitoring of probable hazards and improve situational awareness during the normal operation and maintenance of conveyor systems. To address these issues, researchers from the National Institute for Occupational Safety and Health (NIOSH) continue to investigate emerging technologies that show the potential to improve miner safety around conveyors. This paper presents a feasibility assessment by NIOSH researchers of a fully integrated, commercially available wireless Internet of Things (IoT) system to improve situational awareness around conveyor systems. Included are discussions of a full-scale laboratory test bed that was designed to simulate a working conveyor system as well as the challenges and successes of integrating the IoT system with the test bed.

Oct 6, 2020

By L. A. Ruth

Introduction The US Department of Energy's Office of Fossil Energy has begun a new approach for developing the ultra-clean energy plants. This approach will allow the nation to continue to use low-cost fossil fuel feedstocks during the early decades of the 21st century. The new approach is called Vision 21. The overall goal is to effectively eliminate, at competitive costs, environmental concerns associated with the use of fossil fuels for producing electricity and transportation fuels. Vision 21 is based on the following three premises: •The nation will need to rely on fossil fuels for a major share of our energy needs well into the 21st century. •It makes good sense to rely on a diverse mix of energy resources, including coal, gas,

Jan 1, 2003

By Thomas E. McNider

On July 20, 1990, a Spontaneous Combustion Control Plan was approved by MSHA for Jim Walter Resources, Inc. No. 5 Mine. The mine operated under the plan for twenty-nine shifts before MSHA revoked the plan. A total of fifty-five seals were constructed during the process of implementing the plan. The major difficulty in applying the control concept resulted from problems controlling leakage at the numerous seals. The number of seals was a direct consequence of attempting to merge the traditional bleeder system, used in all the Blue Creek Mines, with the bleederless system Jim Walter Resources proposed as a means of controlling the spontaneous combustion hazard. This paper discusses Jim Walter Resources experience with spontaneous combustion control and the new safety standard which applies to underground coal mines that demonstrate a history of spontaneous combustion and how this standard would apply to our No. 5 Mine. The new Ventilation Standards were published in the Federal Register on May 15, 1992, and scheduled to go into effect August 16, 1992.

Jan 1, 1993

By C. D. Harrison

The 1990 Clean Air Act Amendments specify national objectives for reducing sulfur dioxide emissions from coal-fired power plants System-wide reductions can be achieved by combining various emissions controls technologies and allowances, or compliance credits, that can be purchased, sold, or traded. As part of the Coal Quality Expert development project funded by U.S. Department of Energy and the Electric Power Research Institute (EPRI), Black & Veatch has developed an interactive computer tool, the Acid Rain Advisor (ARA). ARA allows the user to develop integrated system-wide compliance plans by comparing the costs and emissions reduction benefits for emissions allowances and various SO2 control technologies such as coal cleaning, fuel switching, and scrubber retrofits.

Jan 1, 1992

By L. Maday, V. J. Perrone, M. B. Gilbert

INTRODUCTION The Brightwater conveyance system project in King County, Washington consists of constructing about 21 km (13 mile) of effluent and combined influent and effluent tunnels. The influent tunnels will collect sanitary sewerage from the service area and convey it to the new wastewater treatment plant (WTP) site at Route 9 in Woodinville, Snohomish County, Washington. The effluent tunnels will convey treated effluent from the WTP to an outfall at Puget Sound. The tunnels will be constructed primarily under residential areas, busy suburban roads and state highways. This 21 Km (13-mile) soft ground tunneling project faced many design challenges because of the geologic and hydrostatic conditions, long tunnel reaches, and large overburden depths. Boring depths typically varied from 45.7 M (150 ft) to 114 M(375 ft) with a maximum depth of 185.6 M (566 ft) deep. Conventional empirical methods for non-mountain terrain based on a 1:1 ratio of drilled footage per foot of tunnel bore (National Research Council, 1984) for evenly spaced borings provided a good start for the Phase 1 explorations. However a continuation of this approach with closer spacing was deemed inadequate by the geotechnical team for efficiently allocating geotechnical exploration resources for the final design. This paper presents a rational approach that was used to evaluate the value of a particular geotechnical exploration boring, pump test or other in-situ test. The method of analysis, which was initially developed for rock tunnels (Einstein et al., 1978), was modified for the Brightwater project. The method considers the potential construction cost risks resulting from variable geologic conditions, the cost and reliability of the geotechnical exploration and the earned value (cost risk reduction) of performing the geotechnical exploration. PROJECT DESCRIPTION In total the land portion of the conveyance system will include approximately21 Km (13 miles) of tunnels ranging in size from 3.0 to 5.2 M (10 to 17 ft) minimum inside diameter with overburden depths of 30.0 to 168 M (100 to 550 ft) and

Jan 1, 2005

Attractive geology does not guarantee mining investment if a region’s policies are bad, according to mining executives surveyed in the Fraser Institute’s seventh Annual Survey of Mining Companies. Companies responsible for a combined US$642.4 million in international exploration (during 2002) rated the policy attractiveness and mineral attractiveness of mining jurisdictions around the world. Jurisdictions like Chile, Australia, Quebec and Nevada bolster their attractive geology with mining-friendly policies, the report said. These locations do well on the overall investment attractiveness index. On the other hand, jurisdictions like British Columbia and Indonesia, each with excellent geology, are hurt by their policies, which have lowered their score.

Jan 1, 2004

By Kevin Saeler, Patrick Willaman

Utilizing automation is one way to improve competitiveness. Roof and rib bolting in underground coal mines has not changed significantly for more than 40 years. Most roof bolting is still a largely manual process involving high levels of staff carrying out repetitive work. Roof bolting statistically has one of the highest levels of underground accidents, including finger, hand, and arm injuries. Operators are exposed to falling objects and becoming entangled in roof bolting apparatus while roughly moving awkward 6-ft drill steels and roof bolts. It is estimated that over 25 million roof bolts are installed annually in the U.S. underground coal market with well over 1,500 operators involved in roof bolting on a day-to-day basis. Recently electrohydraulic roof bolting rigs have been installed to offer partial automation of the drilling cycle and the bolting cycle. The next stage is to provide a storage and loading system to allow full automation of fullcolumn resin roof bolts. This paper reviews the latest electrohydraulic roof bolting equipment and discusses the testing of a fully automated drill rig. Full electronic control allows each step of the roof bolting process to be recorded, providing a digital record of each installation, including hole depth, spin time, gel time, torque, and cycle time. Other benefits include monitoring of water pressure and flow, used to prevent blocked drill steels as well as digital fault finding. A fully automated roof bolting machine greatly improves operator safety and gives high-quality repeatable roof bolting with reduced cycle times.

Jul 1, 2023

By B. Anameric, S. Kawatra

Pig iron nuggets, which have similar chemical and physical properties with blast furnace pig iron, were produced by a single step heat treatment of self reducing – fluxing dried greenballs. During this single step heat treatment the transformation of self reducing fluxing dried greenballs into pig iron nuggets did not take place instantaneously. Rather, it was composed of three transformation stages, (1) transformation of self reducing – fluxing dried greenballs into direct reduced iron (DRI), (2) transformation of DRI into transition direct reduced iron (TDRI), and (3) transformation of TDRI into pig iron nuggets. Thus, the objective of this research was to investigate these transformation mechanisms by analyzing the transformation stage products. The transformation stage products were produced at a constant furnace temperature of 1425°C and various furnace residence times. They were characterized according to their microstructure, microhardness and apparent density. The changes in the product’s physical and chemical properties with furnace residence time were utilized in understanding the transformation behavior, the chemical events that took place and the controlling mechanisms. It was determined that the transformations were dictated by the changes in the slag viscosity and wetting properties, and by carbon diffusion into metallized areas.

Jan 1, 2007

By R. J. Good

It is well known that the elimination of impurities such as iron pyrite, shale, clay, silica, etc., from coal, by floatation [Sun, 1954; Aplan, 1983] and selective oil agglomeration [Keller and Burry; 1990] depends on the fact that coal is hydrophobic, and the impurities are hydrophilic. The water contact angle has long been used to evaluate the hydrophobic nature of coal, first by Brady and Gauger (1940), who demonstrated that the contact angle of water on coals increases with rank, and passes through a maximum at about 88% carbon. Brown (1962) found that the contact angle of coal decreased with increasing ash content. Sun, and also Aplan, have reported a direct relationship between values of the contact angle and rank, and have related the contact angle to coal floatability. Horsley and Smith (1951) first demonstrated that the captive bubble contact angle may be used to characterize the hydrophobicity of a coal containing more than 80% carbon DAF, while Parekh and Aplan (1978) have shown that the sessile-drop technique may be used to evaluate the hydrophobicity of coal of any rank.

Jan 1, 1992

By Jodi Banta

In an effort to reverse the trend of declining enrollments to mining engineering programs that began in 2015, the University of Arizona has implemented a number of interventions over the past five years, including ramping up its pre-college mining education and outreach, and undertaking several enrollment research projects. This article is the second of two installments to discuss the results of our latest study. The first part can be found in the September 2025 issue of Mining Engineering magazine. To better understand mining’s competitive position, the School of Mining Engineering and Mineral Resources conducted a comprehensive study to determine: 1. How prospective college students, parents and educators perceive the industry, related careers and the mining engineering degree. 2. Factors affecting students’ choices of degrees and career plans. 3. The roles parents and educators play and how they influence students.

Nov 1, 2025

By G. Folmo

Allis Mineral Systems' GRATE-CAR agglomeration/induration/reduction process is currently being operated to process ilmenite at Tinfos Titan & Iron KS in Tyssedal, Norway. In this process, balled ilmenite concentrate is fed to a traveling grate where pellets are dried and preheated, using fully oxidized kiln exhaust gas. Hot preheated, semi-indurated pellets are fed directly to a ported kiln where reduction of the ilmenite's iron oxide fraction occurs in the presence of lump coal. The reduced pellet sand coal char are discharged from the kiln to an indirect rotary drum cooler. Cooled pellets and char are screened and magnetically separated prior to their further processing in a downstream smelting operation. The pellets are melted and the titanium dioxide and iron are separated. Operation commenced in late 1986.

Jan 1, 1992

By Steve Kral

The Underground Construction Association?s (UCA) 2014 North American Tunneling (NAT) conference is expected to attract about 1,000 tunneling and underground construction professionals. With the theme ?Mission Possible,? attendees from around the world will hear the latest in tunneling and underground construction technology in the two-and-a-half days of technical sessions. The meeting is scheduled for June 24-27 at the JW Marriott Los Angeles Live in Los Angeles, CA. In addition to the technical programming, the accompanying exhibit has attracted 143 exhibitors in 162 booths. And the conference will offer short courses and plenty of social activities that will provide attendees the opportunity to catch up with each other. In addition, a proceedings volume containing all of the 128 papers will be available. An impressive lineup of sponsors will help attendees enjoy the conference. They include Brierley Associates, Kiewit Infrastructure Group, Parsons, Skanska, Traylor Bros., MWH and HNTB.

By Chee Theng

"Mineral processors know you can put in the best technology in the world but it won’t work optimally without the support of the operators. Conversely, you may have complete operator support but won’t get top results without the right technology. When the two come together, the returns can be phenomenal.The first day of talks at the 68th Annual Colorado MPD Conference, held April 26-28 at The Broadmoor in Colorado Springs, covered the ground on these industry wisdoms.Coming together as a team“Think of the people, not just the lab and the numbers. That makes all the difference,” said Dee Kippers, of FMI Henderson Mine, in her talk on “Process optimization during a market downturn (A Moly MacGyver story).” Kippers told an entertaining story of the journey she and her team took in tackling the issue of an annual spike in iron content in the product at Freeport- McMoRan’s Henderson primary molybdenum mine near Empire, CO.As the metallurgists tried one thing after another — cranking up the iron depressant, adjusting pH with sodium hydroxide and hydrated lime, modifying reagent levels — Kippers found that when she shared her results with the operators, communicated with them on what she was doing and got their input, they were more willing to work with her, and more understanding and supportive of her efforts.The results make the case for getting people on board and coming together as a team. The cost savings from their optimization efforts, with little capital investment, have been “enough to cover the annual salaries of our metallurgy department and then some,” Kippers said.Considering the environmentDavid Lemieux, of Dundee Sustainable Technologies (DST), talked next on “Cyanidefree process for gold extraction,” presenting the results obtained from a demonstration campaign of the company’s novel chlorination process for gold extraction and associated arsenic stabilization process. Developed at an investment cost of C$35 million, they are ready for commercialization, having been demonstrated on the laboratory, pilot and demonstration scales.The DST process is differentiated from the Plattner chlorination process, which was in use from 1851 to 1916, by moderate process conditions of atmospheric pressure and ambient temperature — the result of using sodium hypochlorite solution, or bleach, instead of direct injection of chlorine gas — and new, cheaper materials of construction, such as polymers, plastics, fiberreinforced plastics and Teflon, resulting in lower capital and operating expenditures."

Jan 7, 2018