Search Documents

By Tianzu Yang, Weifeng Liu, Lin Chen, BOYI XIE, DUCHAO ZHANG, HUI XIAO

In this study, the oxygen-rich bath smelting process of copper dross was simulated using Factsage software. It was found that the two-step simulation results agreed better with the industrial data, especially in the speiss. Bismuth (Bi), lead (Pb), antimony (Sb), arsenic (As) and copper (Cu) contents in the speiss by two-step simulation differed from the industrial data by 0.6, 0.8, 2.6, 7.2 and 8.6 weight percent, respectively. The two-step simulation results indicate that the speiss partitioning of Sb, As and Cu increased from 60.1, 32.3 and 27.5 percent to 81.6, 67.8 and 47.2 percent, respectively, with the smelting temperature increasing from 1,050 to 1,250 °C, while the metal partitioning of Sb and Cu increased from 0 and 2.7 percent to 15.2 and 13.3 percent, respectively, with the separation temperature increasing from 400 to 700 °C.

By D. K. Adjei, G. Ofori-Sarpong, R. K. Amankwah

"Mercury (Hg) is toxic and has long-term effect on the muscle tissues, the brain and the central nervous system functions due to its bioaccumulation and biotransformation effect. Hg pollution around the world is high and this has attracted much global concern such as the Minamata Convention on Mercury, held in 2013. For several years, mercury has been the chemical of choice for Artisanal and Small-Scale Mining (ASM) gold extraction, accounting for about one-third of the global mercury consumption. A greater percentage of this ends up in the environment through open burning of amalgam, spillage and indiscriminate disposal of waste. To break this wall of mercury pollution, it is very important for the mercury used to be recycled through the use of mercury retort units. This brings into the limelight, the Lantern Retort which tries to synergise the high conductivity of steel and the see-through effect of glass, thus, improving the amalgamation process. A research conducted on improving the original Lantern Retort arrived at an appropriate distillation length of 5.08 cm which was used in redesigning a more efficient retort. The improved Lantern Retort recovered about 98% of the mercury used. INTRODUCTION Artisanal and Small-scale mining (ASM) is an informal mining activities which employ quite simple tools such as pickaxes, sluice boxes, shovels, chisels, metal bars, mattocks and water pumps for mining and processing of gold ores. The artisanal and small-scale mining (ASM) sector has served as source of employment for many people in developing countries including Ghana (Aryee, 2001; Hilson and Potter, 2003; Amankwah and Anim-Sackey, 2004; Amankwah et al., 2010) and has provided a substantial amount of foreign exchange through its activities (Hilson, 2001; Styles et al., 2010). Hentschel et al. in 2003 estimated that about thirteen (13) million people are said to be engaged directly in the small-scale mining activities worldwide. However, an estimated 100 million people are said to depend on this sector for their livelihood mainly in developing countries. In China alone, a projected number between 3 and 15 million people are engaged in artisanal and small-scale mining activities (Hentschel et al., 2003), whilst in Ghana, it is estimated that more than 1,000,000 people are employed directly or indirectly in the artisanal and small-scale mining activities, with 10% being women (Amankwah and Anim-Sackey, 2004; Amankwah and Ofori-Sarpong, 2014). In Ghana, ASM gold production has grown from a low of 2.2% in 1989 to a high of 34% in 2014. This figure is estimated to increase with proper documentation. This indicates that the sector has made significant socioeconomic impact on many individuals and communities as a whole. Notwithstanding the above positive contributions, the sector has also contributed to negative impacts on human, aquatic life and the environment in general due to indiscriminate mercury emission. This ‘pollution wall’ needs to be broken, and several interventions have been put in place including the use of retort units like the lantern retort (Adjei et al., 2014; Amankwah and Ofori-Sarpong, 2014)."

Jan 1, 2017

By O. J. R. Baena, N. J. Zapata

In Colombia, more than 15 regions and around 100 municipalities develop gold mining at different scales, and these operations generate mining waste composed of processing fluids and crushed rock with metals and high silica content. Cement production requires clinker, gypsum and other corrective additives. Clinker results from the partial fusion of some minerals including silica. In this study is proposed to evaluate the effect of the use of mining tailings sands from gold mining in the manufacture of clinker. The proposed methodology will allow the characterization of the sands to manufacture a cement specimen and measure its physical and fire properties

Mar 2, 2022

By Carl R. Peterson

The Rapidex continuous drill and blast tunneling concept utilizes a unique spiral blasting pattern that permits efficient performance with relatively small single shots, while at the same time directing major blast fragments at right angles to the tunnel axis. The concept's self-shielding geometry permits the design of a lightly shielded machine that can stay at the tunnel face firing frequent small blasts to provide rapid, virtually continuous advance. This paper describes Phase III of the development program (supported under Bureau of Mines contract H0252047) in which the "front end" of the machine?drilling loading, and shooting components, together with the shield--was fabricated and field tested underground at the White Pine Copper mine, Michigan. One of the major accomplishments of the Phase III effort was to develop a fully remote controlled loading and initiation system in which explosive slurry is pushed, through a hose into the blasthole by a small water-driven piston carrying the blasting cap. The cap is ignited via an induction coil just prior to entry into the borehole, after which a delay permits complete -withdrawal and shielding of the loading hose. The ultimate objective of the present Bureau-sponsored program is to evaluate the feasibility of mechanizing hard rock mining operations, such as development to a point where drilling, loading, shooting, and mucking can proceed simultaneously and result in increased productivity.

Jan 1, 1977

By William Brundan

INTRODUCTION The Srisailam Left Bank Canal (SLBC) Tunnel Scheme is part of the Alimineti Madhava Reddy Project in Andhra Pradesh, South India. This scheme has been planned since 1983 and will provide irrigation facilities to drought-ridden areas in Andhra Pradesh. Water will be transferred from the Srisailam Reservoir during the monsoon months to 0.3 million acres of farmland and will also provide drinking water to villages en-route. The paper will address the design and onsite assembly of the Robbins Double Shield TBMs for Tunnel-1 of the SLBC tunnel scheme from planning to start-up of the machines. Also, it will provide a current status of the project and describe the advantages of a site assembly. Problems encountered to date and the solutions adopted will also be described. The project comprises over 50 km of tunnels and involves construction of the world?s longest tunnel without intermediate access. The TBM tunnels at 43.9 km in length and 10.0 m diameter will cross the Amrabad plateau, containing a wild life sanctuary and India?s largest tiger reserve, the Rajiv Gandhi. Jaiprakash elected to excavate the tunnel using two tunnel boring machines, rather than by drill and blast, in order to alleviate surface disturbances to environment and the tiger reserve, wild life sanctuary, and protected forestry areas. The Project was awarded to the Main Contractor Jaiprakash Associates Ltd with The Robbins Company as the Tunnel Boring Machine (TBM) supplier in August 2005. The Robbins Company supplied the TBMs along with two continuous conveyor systems and all spares and consumables to complete the tunnel excavation.

By Deepak Malhotra

INTORDUCTION Mining operations are unique In that they handle large volumes of water (millions of gallons) daily. The water contains dissolved metals, processing chemicals, organics, and other contaminants, There are several sources of water contamination at mine sites: mines, mills, tailings ponds, and Industrial/utility complexes. Utility waste water generally represents a very small portion of the total process water utilized in a normal milling operation and hence will not be addressed in this paper. Mine drainage can represent a significant amount, thus having an Impact on the recovery of metals, especially In Industrial minerals operations, and may have to be treated separately. The National Pollutant Discharge Elimination System (NPDES) effluent limits are becoming more stringent, thereby requiring mining operations to treat process water prior to discharge to the environment. The general trend Is to move toward a closed-loop waste system and treat only that small fraction of process water which Is to be discharged to public lands. The following section discusses the reasons for waste water treatment and the existing and emerging technologies for meeting NPDES effluent limits. REASONS FOR WATER TREATMENT Due to the diverse nature of the mineral Industry, process/waste water contamination problems as well as processing flowsheets are site specific. However, certain generalizations can be made specific to processing of different minerals: • Acid mine drainage Is a problem at sulfide/coal mines. • Cyanide contamination of water Is a problem at gold processing plants. • Organics can be a problem at mines using flotation oils. • Tolling ponds are generally acidic at sites processing industrial minerals such as silica sand and feldspar. The cost for water treatment Is viewed as an added cost of production. Hence, large mines are moving toward dedicating personnel to management of water resources in order to minimize waste water for treatment. Very often, mines having closed-loop water systems will treat waste water for reasons other than meeting NPDES regulations. These Include situations where process requirements dictate use of high-quality water for separation of minerals, neutralization of acid mine drainage water, and portable water for the mill. WATER TREATMENT TECHNOLOGIES Water treatment process has to be cheap and simple because It has to process large volume, and It does not directly add to the bottom line, namely revenue. The water treatment process development has to be site specific because the contaminants In the water vary from site to site. and discharge limits for water vary from state to state. The current technologies for wastewater treatment have been divided Into the following three areas: • Removal of heavy metals • Cyanide destruction • Scale control A brief summary of the current technology In each area Is discussed below. Removal of Heavy Metals The physical and chemical processes for heavy metal removal are summarized in Table 1. The most common and cheapest approach has been the precipitation of hydroxides at high pH followed by sedimentation and thickening of solids. The remaining solids can be removed by filtration. The pH is adjusted back to neutral, and the water Is discharged. This process is most commonly used wastewater treatment technology in the mining industry. The basic processes can be modified by combining other operations in order to meet the objectives of the specific site as illustrated In the following examples: • AMAX's Mt. Emmons treatment facility uses Lectro Clear® process where the precipitated solids are removed by electroflotation. • AMAX's Climax Mine water treatment plant used Ion exchange columns to meet the discharge limits on molybdenum.

Jan 1, 1992

By L. Galarza

"INTRODUCTION Beneficiation of ores and minerals in a concentrator plant requires a significant amount of water [1] for the grinding and particle separation processes; most of it ends up being recirculated for reuse, slurry pumps are used after crushing and grinding feeding the ore to a classifier to separate fine-grained material (less than 5 mm) from coarse-grained material requiring further grinding. The lower ore grades [2] in the past couple of decades have demanded an increase on power size and efficiency of process machines to maintain a competitive plant throughput; Hydro-cyclone feed pumps to control both under and over milling or grinding are not the exception; Fig. 1 shows a conventional drive train [3] comprising an (1) asynchronous motor (also known as squirrel cage induction motor = SCIM), a high speed coupling (2), a gear reducer (3) and a low speed coupling (4) attached to the shaft of the pump (5), to accommodate the motor rated speed (typically 1800 rpm) to the process requirements (in the range of 250 rpm to 350 rpm), requiring additional components related to the gearbox: instrumentation, maintenance, disposable lubricants and filters, spare parts, thus reduces the overall system efficiency ultimately reflected into CAPEX and OPEX.WHY VARIABLE SPEED DRIVES FOR CYCLONE FEED PUMPS Hydrocyclones or commonly referred as “cyclones” are one of the most important devices in the minerals industry [4]; almost universally used in close-circuit grinding because of their high capacity and relative efficiency, the evolution of Power Electronics made affordable the use of Medium Voltage - Variable Frequency Converters (VFC) for Cyclone Feed pumps in combination with induction motors larger than 500hp (373kW) to gain multiple benefits: - Soft start with minimum electrical utility disturbance = inrush current mitigation - Full Torque available at zero speed for overload startup with pulp solidification after long still stand periods, superior to any other reduced voltage starting method. - Optimum and constant pump speed (independent of the electrical network or load condition), compared to across the line SCIM operation - Flexible Motor Voltage and Speed regardless of the power distribution Voltage and Frequency - Improved Power Factor (close to unitary), over the entire operating speed range"

Jan 1, 2015

By Howard L. Hartman

Introduction The federal government's declining role in funding research has created a critical dollar gap for university departments of mining engineering. Industry, too, is affected by the drought. Research is lagging. Hardpressed universities are going to the private sector for funding. Mining companies should not shower universities with philanthropy, but a research partnership should be contracted on a pay-as-you-go basis. A model exists at The University of Alabama (albeit not in mining) that could be adopted by the mining industry. An equal partnership arrangement between a university and an industry for conducting research is proposed. The concept is not that a corporation sponsors and a university performs the research. Nor does it call for educational contributions or giveaways from industry. Rather, the corporation and the educational institution enter into a cooperative research endeavor, a full and equal partnership. Both parties contribute and both share the benefits. A key to the relationship is that it has a single objective: it must generate profits or reduce costs for the company. Working Model Recent literature is replete with examples of proposals for joint research endeavors, involving both contracts and grants, between industry and universities (Bronwell, 1971; Bugliarello, 1978; Branscomb, 1981; Sanford and Holland, 1982). They are all good proposals and offer something to both parties. They are, however, not widely supported. Few have received a favorable nod from the US mining industry. Though it may be logical, for example, to remake the American Mining Congress (or some new consortium) in the mold of umbrella-type industry organizations to fund cooperative research with mining institutions, such proposals have never flown. What model, then, will work? First, look for a model that has worked in industry in general. Second, seek to apply it to mining specifically. There is a model project that satisfies the first of those criteria. It is a project complicated by a third party, in addition to a corporation and a university. In January 1983, the "Factory of the Future Project" was initiated between The University of Alabama (UA) and General Motors Corp. (GM). The United Auto Workers (UAW) is a third party to the agreement. The factory was GM's Rochester Products Division manufacturing plant in Tuscaloosa, AL, also home of UA's main campus (Fig. 1). Saving a Plant The agreement came about at the initiative of GM and the UAW. Faced with having to close the plant because of excessive production costs, company and union officials proposed to the university that an applied research facility be established at the plant. The university would operate the laboratory, dedicated to $470,000 a year cost reductions for the company. The school would lease the 5.1 km2 (55,000 sq ft) space for $470,000 a year for three years. Any savings effected by the university's research effort would be credited toward to the rent. GM said the small factory, which made replacement carburetors

Jan 9, 1984

By D. W. Partridge, W. Lamb, A. E. Lamb, S. Bird

Due to the constant need to improve SAG mill performance and efficiency, extensive research into all aspects of SAG mill optimization has been performed. This paper will review the current evolution of SAG mill shell liner design and their performance at the Copperton Concentrator. The effect of these liner design changes will be discussed with respect to: • Liner configurations • Mill operating performance, i.e., throughput, power draw, mill control • Mill mechanical performance, i.e., liner wear profiles, liner life, liner breakage, liner hardness • Foundry manufacturing considerations • Economic evaluation of throughput versus liner life This paper will discuss the results of Kennecott Utah Copper’s (KUC) and ME International’s (MEI) test work, providing an insight into the past, present and potential future opportunities of SAG mill liner design.

Jan 1, 2002

Remote methane detection State and federal regulations require frequent measurements to verify that safe methane levels are maintained in underground coal mines. Ventilation control is the primary means of maintaining safe methane levels. In the immediate face area, where the highest methane levels occur, methane measurements are required every 20 minutes during active mining. To perform these measurements, temporary roof supports must be erected. This allows a miner to reach the face. There a hand-held methanometer is used to make the measurements. This procedure is time consuming and potentially hazardous. To facilitate the measuring process and reduce the miner's exposure to roof falls, the US Bureau of Mines has developed a prototype optical device. It can measure methane remotely from distances up to 12 m (40 ft). The device uses two infrared signals, reflected from the coal face, rib, or roof. One signal is absorbed by the methane, the other is not. The ratio of the two signals determines the average methane concentration in the face area. The prototype detector has also been successfully tested at the Lake Lynn, PA Laboratory. Instantaneous responses were obtained for methane in the ventilation airflow and for methane layered near the roof. Conventional methanometers required from five to 25 seconds to respond to the methane in the ventilation airflow. They did not respond to methane in the roof layer. For more information about the Bureau of Mines' remote detection research, contact Richard W. Watson, US Bureau of Mines, Pittsburgh Research Center, Box 18070, Cochrans Mill Road, Pittsburgh, PA 15236 or call (412) 892-6630. Ignition suppression system The incidence has increased of fractional spark ignition at the mine face. One reason is the advent of mechanical mining. Another is the more difficult ventilation conditions associated with deeper and more extensive underground workings. To cope with the problem of frictional ignition, the Bureau of Mines initiated research to develop a system that would provide rapid detection of incipient methane-air ignition. Then, rapid dispersion of a quenching agent would ensure that the methane flame was extinguished while it was still relatively small. This concept was successfully demonstrated by suppressing explosions in the Bureau's Bruceton, PA experimental mine. But the bulkiness of the early storage-dispersal system proved impractical to retrofit onto face equipment. In a cooperative effort by the Bureau and the Mine Safety and Health Administration, a more compact system has been developed and is being tested. A continuous mining machine has been equipped with four 1.8-m-long (6-ft-long) and two

Jan 9, 1987

By William R. Yernberg

The current state of the copper industry was the topic of discussion at the Copper 99 — Cobre 99conference held Oct. 10 to 13, 1999, in Phoenix, AZ. More than 700 copper-industry engineers, executives, consultants, academics, vendors and other interested parties attended. This successful and well-organized conference was the fourth in a series of international conferences devoted to the mineral processing and extractive metallurgy of copper. The 1999 meeting marked the first time that the conference was held in the United States. The meeting was co-organized by the Minerals, Metals and Materials Society (TMS); the Chilean Institute of Mining Engineers (IIMCH) and the Metallurgical Society of the Canadian Institute of Mining, Metallurgy & Petroleum(CIM). The meeting was also sponsored by The Society for Mining, Metallurgy and Exploration Inc.

Jan 1, 2000

By F. D. Fox

The Flambeau and Ridgeway Mines, both owned and operated by wholly owned subsidiaries of Kennecott Minerals Company, were located very close to populated areas having initial concerns about health, safety and the environment. The success of both operations depended upon developing a framework of community support and enhancing sustainable development opportunities throughout the entire life cycle of the mining operations to address these concerns. The protection of the Flambeau River was the cornerstone of the Flambeau Mine’s success. The highest priority for the Ridgeway Mine was to ensure long-term physical, chemical and ecological stability of the reclaimed mine site. Both of these goals have been achieved and are discussed in this paper, which highlights Kennecott Minerals Company’s integration of sustainable development principles into its business decision-making and management processes.

Jan 1, 2003

By A. C. Smith

Although only used in a few U.S. longwall mines, bleeder-less ventilation systems can be an effective spontaneous combustion control method in mines having a demonstrated history of spontaneous combustion. To provide insights for the optimization of bleederless ventilation systems for U.S. underground coal mines, a computational fluid dynamics (CFD) study was conducted to model the spontaneous heating in longwall gob areas using a bleederless ventilation system. A single longwall panel with a bleederless ventilation system was simulated, and typical longwall mine ventilation data were used in the simulations. The permeability and porosity profiles for the longwall gob were estimated using a geotechnical model and were used as inputs for the CFD modeling. The effects of gob permeability and resistance of the collapsed entries on the spontaneous heating were studied. The effectiveness of using nitrogen injection to prevent spontaneous heating in the gob was also examined.1

Jan 1, 2008

By M. L. Harris, I. Zlochower, M. J. Sapko, I. E. Perera

Experiments conducted with limestone dusts and dolomitic marble dusts have indicated that when rock dust is wetted and subsequently dried, it becomes a solid, non-dispersible cake. However, in order to be effective, rock dust must be able to disperse as individual particles to inert. To counteract this, rock dust manufacturers created treated rock dusts that will resist caking after moisture exposure. National Institute for Occupational Safety and Health (NIOSH) researchers conducted a series of laboratory-scale experiments on four base rock dusts and their treated counterparts to assess the effectiveness of various anti-caking additives after being exposed to moisture and then dried. The dusts were exposed to moisture using humidity cabinets having a high relative humidity (99% RH) and by also exposing the rock dust bed to water through bottom wicking. The dusts were then evaluated for dispersibility after drying using the NIOSH-designed dust dispersion chamber. The anticaking additives were different concentrations of stearic acid, oleic acid, and xylene-based surfactants. All results were compared to a reference rock dust used to conduct large-scale experiments in the Lake Lynn Laboratory (LLL), Fairchance, PA. When the untreated dusts were dried after exposure to moisture for one day, no dispersion was measured. However, rock dusts treated with anti-caking agents were readily dispersible even after exposure to moisture for six months. This report details the analysis and characterization of anti-caking additives using the NIOSH-designed dispersion chamber and the 20-L explosion test chamber. INTRODUCTION In order for a coal dust explosion to propagate, five elements are required. In addition to the fire triangle in which three elements are necessary to sustain a fire—fuel (coal dust), heat (ignition source), and an oxidizer (oxygen in air)—a combustible dust explosion requires dispersion of a dust cloud (pressure wave) and confinement of a dust cloud (underground mine entry) (1). Coal dust explosions can originate anywhere in a mine. For example, when a small volume of a flammable methane and air mixture is ignited in a closed end, the high-temperature gases rapidly expand to create a pressure wave, sometimes referred to as a “pioneer wave,” that may steepen into a shock wave as it propagates away from the ignition source. The shock wave produces a wind that disperses the dust preferentially from any elevated and exposed surfaces (roof, ribs, belt structure, cribbing, etc.). Factors that are known to affect the intensity of an explosion are the dust particle size, the location of the dust within the entry, the dust dispersibility, and the volatility of the coal dust (1). Particles less than 75 μm (< 200 mesh) in size are most reactive (2). Dusts that are located on the roof, ribs, and elevated surfaces are more readily dispersed than dusts on the floor. Therefore, application of quality rock dust in sufficient quantities is essential to inert coal dust and to prevent continued flame propagation. 30 CFR 75.402 and 75.403 require 80% total incombustible content be maintained within 40 ft of the face, and 30 CFR 75.2 defines rock dust acceptable for use in underground coal mines. It also defined that “when rock dust is wetted and dried, will not form a cake”.

Jan 1, 2019

By Jerry Luttman, Mark Dubay, Anvesha Dogra, Elizabeth Dwyre, Wei Hu

The I-75 Modernization Project (Segment 3) just north of Detroit, MI is being delivered as a Design-Build-Finance-Maintain (DBFM), which is a Public Private Partnership (P3). The project includes design and reconstruction of 5.5 miles of freeway, including a depressed section with a 20,630-ft long, 14.5-ft inside diameter, up to 100-ft deep stormwater tunnel, multiple drop shafts, and a pump station. The project also includes a maintenance term of 25-years. This is the first time MDOT has used a P3 delivery method for a major highway and tunnel project. This paper describes the development of the P3 documents, including performance-based tunnel and shaft technical requirements, and the approach to project risk management, financing, and insurance coverage.

Jun 23, 2024

By Edmund C. Bitzer

The unit costs of dry crushing, within the efficient reduction ranges of equipment now available, are considerably less than those for the reduction of the same material in the same size range by wet mills using grinding media. This is a commonly recognized fact which cannot be disputed; still we find considerable imbalance in costs between the crushing and grinding sections of many operating mills. In other words, there are many instances where more reduction could be accomplished in the lower cost area of dry crushing. In addition, equipment is now available which enlarges this area and makes it possible to consider much finer crushing than has been heretofore economically feasible. There has been a tendency for the past two decades to utilize wet rod-¬milling in the reduction step. This actually amounts to a fourth stage of crushing in a size range formerly served by roll crushers which have fallen from favor on account of high operating costs, Some investigations have indicated that there is not sufficient difference in the operating costs of rolls and rod-mills to give a clear cut advantage to either method, There has for some time been a need and an opportunity for a dry crushing process to improve costs in the range now served by these two systems.

Jan 1, 1965

By J. G. Pippenger

Rio Tinto Coal Australia (RTCA) developed Meandu Mine in Queensland, Australia in 1983 to supply thermal coal to the adjacent newly constructed Tarong Power Station (TPS). In designing the mine, RTCA selected Meandu?s best economic reserves for a 25-year life based on station owner Tarong Energy Corporation?s (TEC?s) estimated life for TPS. That 25-year plan changed dramatically in the early 2000s when TEC approved life extensions to TPS?s four existing units plus construction of a fifth unit. After reviewing Meandu?s remaining reserves, RTCA decided the nearby Kunioon reserve offered the more economic option for maintaining deliveries beyond 2010. Those plans changed yet again in 2007 when TEC chose to purchase the Meandu Mine and nearby reserves rather than extend RTCA?s contract. TEC then selected Thiess Pty Ltd (Thiess) to continue operating Meandu until the new mine at Kunioon could be developed.

Jan 1, 2011

By J. Z. Keating

There are close to two million tons of Industrial Minerals processed and sold in North America wherein the processor/marketer has no affiliation with the source mine. The largest quantity, about 800,000 tons, is barium sulfate, which is sourced in lump ore form mainly from China and India. The Alumina Trihydrate Industry sources several hundred thousand tons from various alumina refineries. Substantial quantities of bauxite, zircon, magnesite, and fluorspar arrive in North American ports each month. There are also rapidly growing quantities of offshore talcs and calcium carbonate ores being processed in U.S. plants. These feedstocks are usually quite pure, have unique properties, and enjoy bulk rail or waterborne freight economies that allow successful competition with locally sourced raw materials. With increasing restrictions on mining activities, and the increasing need for sophisticated functional minerals, the importation of minerals will continue to grow.

Jan 1, 1994

By C. C. Hamilton, G. R. Lane

Traditionally, mineral sands are evaluated by preparing several mineral products using a combination of heavy liquid-, magnetic-, and electrostatic methods. Whole-rock assays (WRA) are then conducted on ilmenite, rutile and zircon products in order to determine trace element contents, which may affect project feasibility. Combined methods can be time consuming, expensive and even outdated due to the use of banned and toxic chemicals such as clerici solution. Coupled with large field-sample quantities, these procedures can potentially introduce unacceptable sampling and related errors. Modern mineralogical analysis techniques can provide complete mineralogical inventories on a single THM product, reducing the amount of processing involved in satisfactory characterization of early exploration samples. A small exploration sample can be processed to produce a small THM concentrate using readily available gravity/density methods. In turn, the THM product is submitted for Whole Rock Analysis (WRA) and mineralogical inspection by X-ray diffraction (XRD), and microscopic evaluation. Modal mineralogy and textural data can be determined using optical methods, automated image analysis, and scanning electron microscope (SEM) based systems. Benefits of automation are reproducibility and the capability of rapidly analysing thousands of particles as opposed to manual optical methods. Automated systems include the use of Automated Digital Image Analysis (ADIS), and SEM-based systems such as the Mineral Liberation Analyser (MLA) and QemSCAN. For detailed mineral chemistry, microanalysis techniques ranging from electron microprobe (EMPA) to Secondary Ion Mass Spectrometry and Laser Ablation Mass-Induced Coupled Plasma-Mass Spectrometry (LAM-ICP-MS) are used. Examples of these automated and analytical methods are presented. ADIS at SGS-Lakefield Research uses optical characteristics to identify and measure mineral species in THM samples; rutile, pseudorutile, ilmenite and leucoxene can be distinguished. Analysis of a single THM product provides bulk modal mineralogy and grain size distribution of particles and the individual mineral grains. Textural information is also obtained detailing mineral associations as well as degree of alteration. Where textural and chemical resolution renders mineral identification ambiguous, SEM-based methods offer better resolution. Examples of this ambiguity are shown in this paper, which leads to QemSCAN as the preferred method where within-grain variability is concerned. Sampling and measurement strategies are followed to meet study objectives, providing a value-added framework for a sequential, cost-effective strategy, which will meet due diligence and bankable accreditation criteria. Studying a THM product by electron microprobe and LAMICP-MS may reveal potential fatal flaws related to mineral chemistry. Low detection limits in the range of 200 to 500ppm are possible using electron microprobe analysis for suitable matrixes (U, Th in zircon). For the detection of ultra low level elemental contaminants, LAM ICPMS is the most accurate method of evaluation. Elements including U, Th, La, Ce, Nb, and V in Ti-minerals can be determined down to 50 ppm.

Jan 1, 2005

By J. T. Hollow

The Fort Knox Mine is located in Alaska?s interior, where the average ambient air temperatures range from -24°C (-11°F) in January to 16°C (61°F) in July. The mill processes a free-milling gold ore utilizing both a gravity recovery circuit and conventional cyanide leach/carbon-in-pulp circuits. Mathematical models have been developed to accurately predict the impact of leach circuit slurry temperature on gold leaching, carbon adsorption and cyanide destruction kinetics. Additionally, an energy-balance approach has been used to model the seasonal variations in slurry temperatures throughout the Fort Knox mill. The energy-balance model, combined with the kinetics models previously developed to predict plant performance, was used to justify a tailing thickener installation at the Fort Knox Mine. This paper describes the development of the energy-balance model and its prediction of plant performance assuming a tailings wash thickener to reduce heat loss from the mill. Also presented is an analysis of the post-project plant performance that validates the model and shows that the mine produced an additional 596 kg (19,155 oz) of gold while reducing mill reagent costs by $6,302,000 during the first 38 months of operation.

Jan 1, 2007