Search Documents

By J. A. Marts

Reservoir properties including porosity and permeability distributions in longwall coal mine gobs have direct application to modeling the flow patterns and gas distributions in the gobs. Proper assessment of these distributions is required to assess gob gas hazards such as spontaneous combustion and explosive methane mixtures and to optimize gob gas venthole operation and nitrogen inertization. Determining the reservoir properties is difficult given that the gob is inaccessible and direct measurements cannot be easily taken. Several techniques had been used by previous researchers and will be discussed. This paper will present the methodology used to model the gob compaction by simulating the sequential extraction of coal. Two Western US coal mines were used for case studies. By determining volumetric strain, the porosity and permeability distributions in the gob can be calculated. The geo-mechanical model predicts an axisymmetric volumetric strain distribution with a steeper slope near the start-up room and a shallower slope near the active face.

By Francois E. Heuze

The mined geologic burial of high-level nuclear waste is how the favored option for disposal. The underground repositories must keep the waste away from the biosphere for very long times - several thousands to tens of thousands of years. Also, access must be maintained to the vaults for several tens of years, so that the waste can be retrieved, if necessary. Both the excavation of the underground chambers, and the radiogenic heating will disturb the rock mass. The overall rock mechanics problem is to understand and predict the processes associated with these perturbations, and their impact oh the isolation and containment of the waste (3)**. The specific rock. mechanics issues which have been identified for the three candidate hard rocks (basalt, granite, and tuff), are summarized in Table 1. The table also indicates the level of adequacy of our knowledge in the areas of the various issues. Such an evaluation is consistent with the general consensus of the rock mechanics profession, as explained in several key reports and publications (1 to 11). The main shortcomings of today's rock mechanics for waste repositories can be summarized as: ? lack of resolution for remote mapping of fractures in rock masses ? great difficulty in testing large volumes of rocks to determine their mechanical properties.

Jan 1, 1981

By Max Friedemann, Alexandros Bousdekis, Anna Gustafson, Helmut Mischo, Håkan Schunnesson

Many devices used in mining are not monitored by sensors or do not have their own intelligence. By retrofitting sensors and real-time data processing, machines can be integrated into an existing digital infrastructure. Within the project Mine.io funded by the European Union a Sandvik DE110 exploration drill rig is being digitized using various AI algorithms at research and education Mine “Forschungs- und Lehrbergwerk Reiche Zeche (FLB)” of TU Freiberg. The aim is to increase the productivity of drilling with real-time evaluation of the current rock to be drilled and the current maintenance status of the drill rig. The drill rig is equipped with a speed sensor, pressure sensors in the hydraulics, 3-axis vibration sensor, borehole length measurement and temperature sensor. The sensors are additionally attached to the drilling rig and no structural changes on the drill rig are necessary. All data are processed real-time at a server structure outside of the mine using AI algorithms to analyze which rock (ore or host rock) is being drilled and to perform predictive maintenance. Processed Data are visualized for the operator to optimize the workflow and the productivity.

Feb 1, 2025

By H. D. Brenk

"The German Federation of International Mining and Mineral Resources (FAB) is a federation of German companies that are active in international mining and mining related business. The FAB presents a platform for the exchange of information about the worldwide mining commodities in the dialogue with German and foreign institutions. The expertise of the member companies in mining and related activities is based on a long term operation and consulting experience in Germany and abroad. This forms the basis for the special international competitiveness "Made in Germany". The FAB is particularly engaged in the following topics and tasks and acts as a focal point for: • international project developments with the German mining industry, • sustainable mining, consulting and equipment services, • geological and environmental technologies, • project financing and • intermediation of contracts, project enquiries, professional symposia and events. The FAB acts as a contact- and coordination site for international business partners, organizations and governmental authorities. Together with the federal government the FAB organizes bilateral working group meetings in the commodity and mining sector. Project enquiries are being distributed from the FAB among their member companies."

Jan 1, 2011

By T. C. Souza Pinto

Because shape is an assessment of the three-dimensional form of a particle, it may be described in terms of sphericity (?), which is a measure of how closely a particle approaches a spherical configuration. In this study, Darcy?s law and the Kozeny-Carman model for fluid flow through porous media were applied to packed beds to determine the sphericity (?) of apatite particles. The beds were composed of glass spheres or particles of apatite (igneous from Brazil and sedimentary from the United States) of three classes of size (Class 1: -297 +210 µm; Class 2: -210 +149 µm; Class 3: -149 +105 µm). Glass spheres were used to validate the model because of its known sphericity (? = 1.00). Apatite particles, either igneous or sedimentary, showed very close values for particle sphericity (? ? 0.6). Observations on particle images conducted by scanning electron microscopy illustrated that igneous (? = 0.623) and sedimentary (? = 0.644) particles of apatite of Class 2 predominantly exhibit elongated shape. The close value of particle sphericity (? ? 0.6) showed by either igneous or sedimentary apatite may be justified by the similarity in particle shape.

Jan 1, 2009

By C. V. Deutsch, D. A. Silva

The geologic modeling of multiple domains is required for the prediction of mineral resources and reserves. In general, explicit methods have wide acceptance among modelers due to the ability to manually add deemed important trends and geological features into the models. As an alternative, implicit geologic modeling techniques are increasingly adopted to reduce professional time requirements. These methods aim for objective, repeatable and flexible models by replacing the manual time-consuming interpretation of sections with the interpolation of signed distance values. These techniques, however, have been developed for the binary case of two domains at a time. The current paper presents an algorithm that extends the binary case to multiple domains. The method is able to transfer large-scale geological features from data to geologic models. A case study illustrates the benefits of the algorithm and practical implementation considerations.

Jan 1, 2016

By M. C. Mound, E. Gallestey, C. Colbert

Continuous operating performance and high profit is one of the major concerns in the mining industry. Information systems are expected to reinforce and enable conformance to these requirements. The companion efforts of business management and production information systems press for tighter integration to avoid over-laps, multiple instances of similar data, and expensive maintenance of databases. Implementation of advanced intelligent systems throughout a mine operation can reduce costs, optimize investment and create a shorter payback via conversion of the data accumulated by field and process devices into information, and subsequently, into decisions. However, in order to harness the potential power inherent in these intelligent devices, adequate and flexible modular knowledge-based solutions are required. Fortunately, there has been at least one such practical response to this challenge, namely the ABB IndustrialIT portfolio. With these tools in place, production efficiency is reached via integration of process, production, and quality information. Moreover, they permit immediate detection and remedial action to changes to process and boundary condition variables. Finally, using advanced optimization techniques supported by dedicated mathematical models, they allow for economic process optimization (process set points and coordination thereof, energy management, production planning, energy supply contract optimization, etc) of the plant as a whole.

Jan 1, 2004

By Andrew Finney

INTRODUCTION The Sacramento Regional County Sanitation District (SRCSD) serves unincorporated areas of Sacramento County, parts of the cities of Sacramento and Folsom, and the cities of Citrus Heights, West Sacramento, Rancho Cordova, and Elk Grove. SRCSD maintains 145 kilometers (km) (90 miles) of interceptors that convey a combined total of 0.6 million meters3 per day (160 million gallons per day) or more of waste-water, with additional miles of sewer interceptors that are scheduled to be built by 2020. Wastewater is conveyed to the Sacramento Regional Wastewater Treatment Plant in the southwestern portion of the County, also managed and operated by SRCSD, in interceptors with diameters as large as 3.0 m (120 inches.) As part of its overall expansion program, SRCSD has constructed a number of major interceptors over the last few years with tunneling methods due to concerns associated with either the impacts of open cut construction in an urban environment (traffic, safety, noise, environmental concerns) or the need to achieve a crossing of a stream, river, or transportation corridor. This paper focuses on a specific issue that affected construction of the Upper Northwest Interceptor (UNWI) Sections 3&4 project, located at the northern limit of the SRCSD service boundary and within the limits of the City of Sacramento. This project involved the construction of 3.2 km (2 miles) of 2.1-meter (84-inch) and 2.4 km (1.5 miles) of 1.7-meter (66-inch) diameter reinforced concrete pipe (RCP) using MTBM, EPBM, and 3.3-meter (130-inch) two-pass TBM methods. The owner elected to install the RCP using tunneling for a number of reasons including a desire to avoid traffic impacts in a dense urban corridor, to minimize disturbance to the neighborhood, and to avoid potential dewatering-induced settlement issues along the western one-third of the project. For the western portion of the alignment the 2.1-meter (84-inch) reinforced concrete interceptor pipe was to be installed using a 2.7-meter (105-inch) earth pressure balance machine (EPBM). No external dewatering of shafts or tunnels was permitted for reasons of concern about settlement, discussed previously. At the intersection of Elkhorn Boulevard and Natomas Boulevard (at the extreme northwest corner of the project) the 2.7-meter (105-inch) EPBM tunneled past a recently constructed 11-million liter (3-million gallon) water storage reservoir, passing within 3 meters (10 feet) of the tank?s shallow foundation while tunneling through clean sands with a shallow groundwater table. The paper will discuss the implemented solution to mitigate additional settlement risk that was developed as a joint collaboration between the owner, CM, designer, and contractor.

By J. Platt

Recent EPRI research on utilities? likely strategies to reduce sulfur emissions differs sharply from policy analyses showing all- switching or all-scrubbing choices. Energy Ventures Analysis, with Stearns-Catalytic and A. T. Kearney, estimated sulfur-removal costs for scrubbing or switching at virtually all affected plants in the 31 Eastern States. Cost tradeoffs occur between $30 and $40-plus per ton FOB mine in Central Appalachia ($33-44-plus per tonne). 1/2 to 3/4 of total sulfur reductions comes from scrubbing, whose costs act as a cap on low-sulfur coal prices. In a severe environmental scenario, low- sulfur coal demand evaporates, replaced by very low-sulfur (0.7%) coal demand. Additional findings and implications of EPRI coal supply and market studies will be reviewed.

Jan 1, 1987

By J. O. Marsden, C. Green

In 2003, a high-temperature pressure leaching circuit to treat copper sulfide concentrates was commissioned at the copper/molybdenum operation at Bagdad, AZ. In late 2007, a medium-temperature pressure leaching circuit was commissioned at the Morenci mine in Arizona. The Morenci circuit was shut down in mid-2008, following a fire in the autoclave circuit. The onset of the global financial crisis in late 2008 resulted in significant changes to the operating profile in the Southwestern United States with respect to concentrates production, concentrates treatment, acid production and acid consumption. As a result of these changes, the Morenci concentrator was shut down, and the pressure leaching circuit remained offline. In late 2014, the increasing acid requirements in the Southwestern United States prompted a reevaluation of the Morenci concentrate leaching facilities. As a result, the pressure leaching circuit was restarted in high-temperature (200 °C) mode in May 2015 and has operated successfully for three years since recommissioning. This paper describes the current pressure leaching circuit configuration and the factors leading to the successful application of copper sulfide concentrate leaching at this location.

By Robert W. Greene

Next month, American Commercial Barge Line Company will begin moving coal from mines on the old Camp Breckinridge property in Western Kentucky to TVA's new 2600 MW steam plant at Cumberland City, Tennessee. By April of 1973, this movement will reach a level of 7,000,000 tons per year. TVA bought the coal rights to this property from the General Services Administration in 1965 for approximately $7 million. The reserve contains about 120 million tons of recoverable No.9 coal, and about the same recover-able amount of No. 11 coal. TVA then contracted through competitive bidding with Peabody Coal Company to mine the No.9 seam through two slope shafts. The mines are about 300 feet deep and are separated by the one major fault on this property. The mine portals are approximately 3-1/2 miles apart, with the northern portal being over nine miles distant from the Ohio River (see Figure No.1). In 1969 TV A took bids on alternate methods for transporting 120 million tons of coal to Cumberland City at seven million tons per year. These alter-natives included overland transportation to the Ohio River by rail or conveyor, water transportation from Union County, Kentucky to Cumberland City, and total transportation packages from Camp Breckinridge to Cumberland City. The latter could be a joint land/water package, or all land (rail). Ultimately American Commercial Barge Line was awarded an $88 million package transportation contract to convey the coal from Camp Breckinridge to Uniontown, Kentucky; to store it at Uniontown in a quantity sufficient to allow ratable delivery to the steam plant; and to barge from Uniontown to Cumberland City via the Ohio and Cumberland Rivers.

Jan 1, 1971

By Bruce R. Lipin

Chromite, the only ore of chromium, occurs almost exclusively in mafic-ultramafic rocks and their weathering products. However, not all kinds of mafic-ultramafic rocks are favorable hosts for possible low-grade chromite deposits. For instance, chromium-bearing basalts are not favorable because they commonly contain < 0.3% Cr2O3, and chromite is almost always less than 50 um in diameter, if it is present at all. Chromite-bearing ultramafic rocks in stratifonn and alpine complexes tend to be either ore grade (> 25% Cr203) or very low grade (< 2% Cr203); intermediate rocks are scarce. In most complexes large tonnages exist only in the < 2% Cr2O3 group and the composition of the chromite is commonly unsuitable for metallurgical use. Some nickel laterite districts contain more than 108 tons of material with 2.0% to 5.5% Cr2O3, and hence, chromium could be a byproduct of nickel in some laterite districts.

Jan 1, 1982

By Russell Barr

Strategic alignment throughout a mining organization is critical to effective strategic execution and good business performance. The alignment of strategic goals and objectives in the different operations and functions in a large global operation is a challenge facing executive management in light of legacy organizational structure and processes. An additional confounding factor in strategic alignment of acquisition and new project expansion is that mining projects and operations are frequently multi-cultural in terms of country origin as well as organizational culture. This brings together many cultures to accomplish the project or complete an acquisition (Financial Times, 2006). The mining industry presents numerous challenges to executives and mine management by the nature of the operation and organizational processes used in running it. For example, there seems to be an inherent conflict between the individual goals of the components that constitute a mineral processing operation (the mine, the mill, the smelter and the refinery), and lowest cost production of the final product. Managers of these component operations have specific objectives passed down from the corporate executives. Those site managers tend to be compensated based on throughput and perform to this main metric. This tendency to maximize throughput for an individual operation can contradict the general process flow of a best-fit solution to producing the final product at the lowest cost. In an effort to become more aligned, firms are increasingly using balanced scorecard derivatives at great cost and effort (whether internally or externally sourced) in an attempt to help with strategic alignment. Balanced score-cards have been effective in providing a good strategic scorecard to companies with some measure of strategic alignment. Many firms make this effort of using balanced scorecards. However, most firms are not strategically aligned or, at best, are sub-optimized, in terms of strategic alignment (Kaplan and Norton, 2006). The tendency in mining operations is to focus on operating individual components as optimally as possible and stretching existing assets to the best possible production rates. ?Making tons? is the common operational focus. Numerous factors underpin this focus and can affect the ability of the operation?s ability to align properly with the corporate strategy and strategic goals. Critical factors are legacy organizational structure, culture, processes and performance measurement systems. Changing anyone of these factors to affect better strategic alignment requires significant attention to managing change.

Jan 1, 2008

By G. Tiess, S. Mujiyanto

Indonesia is a fast growing democratic developing country comprising more than 17,000 islands, founding member of ASEAN and a member of the G-20 major economies. It is one of the most highly mineralised countries in the world, the mining sector playing a pivotal role in the country&apos;s economy. In 2001, the Decentralization Law No. 22/1999 came into force and caused a transfer of authority and responsibility from central to regional and local administrative governments. The new Mining Law of 2009 substituted its 40 year old predecessor, but lacked detailed regulations for its implementation. These were only issued in 2010, which lead to a period of great uncertainty for investors in the mining industry. The new legislation intends to foster domestic economic development, which may be interpreted as protectionist policy. For the development of a sustainable mineral resources policy, further endeavours will have to be made.

Jan 1, 2011

By Håkan Stille, Jalaeddin Y. Rafi, Fredrik Johansson

"INTRODUCTIONIn tunneling projects, pre-grouting is performed with the purpose of establishing an impervious zone around the tunnel periphery. This is obtained by reducing the penetrability of the most conductive fractures in the rock mass. The main attention, besides economy of the project, is given to limiting the ingress of water into the tunnel to a certain amount during construction s well as operation period. Failure in pre-grouting process may, according to Bruce (2007), significantly affect the project in terms of safety, performance, cost and time. In this respect, determination of design parameters (pumping pressure, properties of the mix and stop criteria) affects these projects significantly. In current practices, depends on the geological conditions and requirements of the project these parameters differ widely. Weaver (1991) recommends selection of design parameters, specifically grout injection pressures, based on site specific factors and the conditions at each specific hole into which grout is to be injected (grout hole logging and water pressure test data). Houlsby (1990) correlated the allowable grouting pressure to the quality of the rock mass and the rock cover above the grouted fracture. In his methodology, grouting should be continued until the maximum pressure was attained. Later, Lombardi and Deere (1993) introduced the Grout Intensity Number (GIN), which limits the combination of injection pressure and injected grout volume in order to control the energy induced in the fracture i.e. avoid fracture jacking. Even though the GIN method was a step forward in understanding of the mechanism of the fracture deformation, there are ambiguities connected to this methodology, thus determination of the intensity number is challenging (see e.g., Rafi and Stille 2015)a.A main problem when no theoretical solution is practiced is that effects from the chosen injection pressure, such as possible increases of transmissivity and changes in total grouting time, remains hidden in the overall grouting process. The question is if a high or a low pressure should be used to fulfil the requirements of the projects at the lowest possible cost."

Jan 1, 2016

By M. Ghiani

Biohydrometallurgy originated, some forty years ago, from an environmental problem, namely the serious pollution of the Ohio river by acid drainage water coming from neighboring subbituminous coal mines. Studies aimed at elucidating the cause of the intensive oxidation of the iron sulfide (pyrite) inclusions of those coals, led to the discovery of a bacterium, Thiobacillus ferrooxidans (Temple and Colmer, 1951), capable of acting as a catalyzer, accelerating the otherwise very slow chemical oxidation of iron sulfide to rates many orders of magnitude higher. However, it is now recognized that the biotechnology of microbial mining dates back to 1963, when the ability of this bacterium to solubilize copper from sulfide ores was ascertained (Razzell and Trussell, 1963). Much research has been carried out on biohydrometallurgy over these last 25 years and is still being actively conducted all over the world. The interdisciplinary nature of this young branch of science and technology is reflected by the variety of experts involved: microbiologists, mining engineers, hydrometallurgists, physico-chemists, mineralogists, solid-state physicists and biochemists. This intensive research effort has provided a solid background on the fundamentals of this technology, although many important issues have still to be solved, amongst which the enzymatic mechanisms controlling biocatalysis of mineral sulfides dissolution, the influence of bulk- and surface solid-state physics of metal sulfides on dissolution mechanisms, the interaction of the various strains composing natural microbial floras. Their elucidation should permit the rationalization of biohydrometallurgical techniques and the optimization of commercial processes. Biohydrometallurgy has already achieved satisfactory results: copper recovery from submarginal copper sulfide run-of-mine ores (i.e. assaying less than 0.3% Cu) by in-situ, dump and/or heap leaching is successfully practised in many countries and uranium recovery through bioleaching is competitive with other leaching processes.

Jan 1, 1987

By L. Larrimore

Electric utilities depend heavily on coal as a major fuel source for power generation, annually producing more than 85 million ton&apos;> of ash, boiler slag and FGD (flue gas desulfurization -"scrubber") materials as by-products. Utilities and others who burn coal have traditionally disposed of these by-products in ponds or landfills. However, in the last 10-15 years there has been a greatly increased emphasis on beneficial utilization of these materials by the producers themselves as well as by customers who purchase the by-products. Regulatory, cost and technical performance issues currently impact the use of coal ash and other coal combustion by-products (CCB).

Jan 1, 1997

By Chester M. F. Peters

The opportunity to make a close study of the available geologic data existing along the line of the California Aqueduct crossing of the Garlock fault in the Tehachapi Mountains was brought about first by my involvement in the prebid examinations, and later with contractors&apos; claim cases. The California Aqueduct crosses through the western end of the Tehachapi Mountains and cuts across the Garlock fault zone at a location about 9 miles east from its junction with the San Andreas fault zone. This is about 65 miles northwest of Los Angeles and 38 miles southeast of Bakersfield (Fig. 1) (1). This map was published after the tunnels were started and shows the corrected geology. At the crossing the fault has north and south branches which extend northeastward for about 22 miles before converging. In the vicinity immediately east of the tunnel line the north branch of the fault starts to converge toward the west. After crossing the line it passes under the upper plate of the apparent easterly extension of the Pastoria thrust fault, so the actual junction with the south branch is obscured. The aqueduct design called for the expected active slip zone of the north Garlock fault branch to be crossed by the 2,800 foot long Pastoria siphon, which connects with the north portal of Tehachapi Tunnel No. 3. The tunnel would extend through the western end of Genghus Ridge which lies between the north branch and the main south Garlock fault zone in Beartrap Canyon. Here again the

Jan 1, 1997

By James W. Estep

The sulphur shortage that has occurred in the past two years has directed attention more and more toward sour natural gas reserves, Wellhead values of sour gas vary widely depending upon the acid gas composition, location, market conditions, and necessary processing charges. Preparation of a saleable residue gas is considerably more involved and expensive than that normally encountered in treating a sweet gas. Recent revisions in sales gas specifications have increased capital costs and processing charges. The presence of hydrogen sulphide and carbon dioxide in a natural gas contributes to shrinkage factors that may approach 50%. Fuel required by the gas sweetening process and sulphur slant tail gas incineration also contributes to a further reduction in the volume of residue gas available for sale. The additional processing facilities involving gas sweetening, mercaptan removal, expanded utilities, sulphur recovery and sulphur handling, all demand additional operating and maintenance staff. A favorable sulphur market under certain conditions may justify the processing of sour gas whereby sulphur is either a by-product or a co-product, Five typical cases involving different compositions of sour gas are presented for evaluation. Capital costs, operating problems, and operating costs are presented in detail for full economic evaluation

Jan 1, 1967

By J. W. Wilson, P. C. Graham

SUMMARY The Witwatersrand quartzites in which South African gold mining operations are moat exclusively conducted, are notoriously difficult and costly to drill. Despite this situation, however, with the high cost of developing new mines and extending existing mines, together with the rising cost of labour and mining problems resulting from the ever-increasing depths of workings, the demand for raise-boring in these formations is increasing rapidly. Not only is the demand for raises and shafts increasing, but also the length and size of these excavations. Raise-boring studies carried out in South African gold mines have indicated that increased penetration rates and possibly reduced costs could be obtained if higher thrusts were available at the reaming head. Until fairly recently there has been no raise-boring machine suitable for underground use that possessed the thrust and torque characteristics necessary to achieve high penetration rates in hard abrasive quartzite formations and the cutters available were not really developed for high loading. In response to these requirements a raise-borer, the Robbins 83R was designed and built in Seattle, U.S.A. for the Anglo American Corporation. This machine is operating in South African gold mines and is currently being used at a depth of 12 000 ft below surface in one of the. Group&apos;s mines. The initial raises bored have substantiated that increased penetration is attainable at high thrust and it is now apparent that the machine is sufficiently versatile to drill raises of up to 12 ft in diameter in quartzite formation over a length of 2 000 ft.

Jan 1, 1974