Search Documents

Resolution Copper Mining LLC (RCML) is currently in a Pre-feasibility study evaluating a large and deep copper and molybdenum deposit in the historic mining district east of Superior, Arizona. Work scheduled for the next several years includes dewatering the existing shut-down mine (the Magma Mine) and sinking an exploratory shaft to 2,130 meters (7,000 feet) below the surface. To dewater the Magma Mine and sink the exploratory shaft, RCML must extract and manage about 2 billion gallons of accumulated mine water inventory, as well as about 300 million gallons per year of new inflow. In order to conserve a valuable water resource in a desert environment, RCML worked with the New Magma Irrigation and Drainage District (NMIDD) to provide treated mine water to blend with and supplement the NMIDD?s water supply to approximately 2,000 hectares (5,000 acres) of farmland located east of Phoenix. A 44 km (27-mile) pipeline was needed to convey the treated water. It was essential that a treatment system be used which could reliably meet irrigation water quality goals, produce a non-scaling effluent to maintain pipeline flow capacity, and generate a dense sludge minimizing disposal cost and volume. This paper describes the resulting mine water treatment and recovery system (MWTS) and how the system has performed against objectives.

Jan 1, 2011

By H. G. Stephenson

Canada and the United states are both developed countries with economies which are extremely dependant on oil. Canada exports 37% of its production (to the United states) and imports 35% of its consumption (mainly into Eastern Canada), making the country self-sufficient in oil. Canada is attempting to increase its oil production so as to simultaneously reduce its dependence on foreign oil while producing more oil for export. The United states -imports no less than 50% of its total consumption of 17 million barrels/day. Canada's exports to the United states form only 7% of the United States total imports. The United States would clearly prefer to achieve self-sufficiency in oil. Consequently both countries are dependent on foreign oil. The united States is however in the sensitive situation of depending, for its imports, on countries which are susceptible to destabilizing political events. It is the author's hypothesis that recent developments in underground oil recovery from the Athabasca oil Sands of Alberta may well, for both countries, form part of the solution to these problems.

Jan 1, 1991

By Pieter-Jan Kleiterp

Highwall mining is a mining method to extract coal from a final boundary in opencut mining, trench mining or contour mining. This boundary may have been reached because of economic constraints (economic strip limit) or geographic constraints, such as spoil heaps and rivers. Coal is mined from visible, horizontal, or near-horizontal coal seams by making rectangular, parallel, unsupported drives with an unmanned cutterhead and coal transport system. This is controlled from a mining unit, or launch frame, positioned outside the drive, in front of the highwall. Removal of overburden is not required or is limited to small quantities only.

Jan 1, 2010

Flooded-bed scrubbers on continuous miners have been shown to be an effective respirable dust control technology, traditionally used during the extraction of extended cuts of up to 12.2 m (40 ft). To effectively use scrubbers in faces that employ exhaust ventilation, the return ventilation curtain or tubing should be located outby the scrubber discharge on the continuous miner, which results in a setback distance from the face of approximately 12.2 m (40 ft). The goal of this research was to compare respirable dust levels generated in 6.1 m (20 ft) cuts when using extended curtain setbacks with a scrubber operating to dust levels in 6.1 m (20 ft) cuts when using traditional exhaust face ventilation without a scrubber operating. Dust surveys were completed at three mines with area and personal sampling conducted to quantify respirable dust concentrations on a cut-by-cut basis. Sampling results did not show a statistically significant difference in respirable dust at the continuous miner or shuttle car locations with and without the scrubber operating. However, with the scrubber operating, respirable dust concentrations in the return airstream downwind of the miner showed reductions of 91%, 86%, and 40% at Mines A, B, and C, respectively. The reductions at Mines A and B were statistically significant. Likewise, reductions in respirable quartz dust levels in the miner return were observed at all three mines, with statistically significant reductions of over 80% observed at Mines A and B. Consequently, operation of the flooded-bed scrubber did not impact respirable dust levels in the face area but did significantly reduce respirable and quartz dust levels downwind of the continuous miner. These results were obtained with the mines operating at or above the minimum operating levels specified in their ventilation plans.

Feb 23, 2014

Adverse ground behavior events, such as convergence and falls of ground, are some of the most significant challenges and hazards in underground mines. Our goal is to work toward mine-wide, digital, and real-time three-dimensional geotechnical situational awareness and predictive capabilities in complex underground mining operations. This will benefit operators, engineers, and management by enabling them to develop a more proactive approach to ground control. To this end, and inspired by research in the field of remote sensing and autonomous robotics, this paper assesses the potential of mobile light detection and ranging (LiDAR) data acquisition for high-frequency, high-accuracy monitoring tasks in Global Navigation Satellite Systems (GNSS) deprived underground mines. Limitations of current monitoring practices are reviewed. Relevant academic and commercial developments in the fields of indoor mobile mapping systems (MMSs) and simultaneous localization and mapping (SLAM), robust autonomous robotic platforms, and automated remote sensing data processing are highlighted, and their current shortfalls are evaluated. To conclude, the ramifications of this work for the development of future autonomous underground mine monitoring solutions are discussed.

Jul 28, 2020

By T. J. Morris

"From November 2014 through September 2016, Westmoreland’s Coal Valley Mine utilized a Marion 7450 electric walking dragline to extract 1.2 million tonnes of a vertically-dipping, 52-meter wide, fault-thickened seam, beneath a conventionally-excavated pit bottom. Mine planning and operational hurdles encountered throughout a kilometer of mined strike length included mitigating highwall instability in both hanging and footwall slopes, water management, and end-of-life machine reliability and maintenance. The most substantial challenge has been the depressed global coal market. However, the successful application of this mining method significantly aided the overall cost of production at the site. The valuable experience gained from this project will be extended to future mining areas where this technique can be similarly applied. INTRODUCTION Coal Valley Mine is located approximately 220 kilometers southwest of Edmonton, Alberta, Canada, in the foothills of the Rocky Mountains. Since commercial production began in 1978, more than 84 million clean tonnes of coal has been produced and sold domestically as well as exported overseas for power generation. While the existing processing plant has a nameplate capacity of 4 million tonnes per year, the site has operated at a 2 million tonne rate since 2015 due to depressed export markets. Westmoreland acquired the mine as part of its purchase of Sherritt Coal Operations in April 2014. The mine operates 24 hours a day, 7 days a week, with an IUOE workforce of 261. GEOLOGICAL SETTING The geology of the Yellowhead Tower mining area differs significantly from previous mining areas at Coal Valley. The Mynheer coal seam discussed herein consists of steeply dipping, highly-sheared, thrust-faulted, and heterogeneous coal pods. Deep set, southwest striking thrust faults were the likely mechanism for the podding and have resulted in overturned, rolled and highly sheared seams with zone thicknesses of up to 65 meters.The hanging wall is characterized by soft bentonitic mudstones and siltstones, overlain by massive competent sandstone. The footwall is defined by a hard volcanic tuff, interbedded with thin, sporadic coal seams. The sandstone above and volcanic tuff below constrained the faulting system within this zone, enabling the mass podding that has afforded the opportunity for large-scale mining."

Jan 1, 2017

By James S. Redpath

"The ways of the world be many and most of the ways be tried, you follow in the footsteps of others till you come to the great divide". These words, written by Robert Service a long time ago, come to mind when I think of our original attitude upon entering into a contract with the International Nickel Company to sink the deepest shaft in the world outside of the Union of South Africa. This shaft was to be sunk to a depth of 7,137 feet from surface, and while it was recognized by all concerned to be a somewhat unusual undertaking in our part of the world, the fact that quite a few shafts had already been sunk to this depth in South Africa probably gave us the feeling that we were following in the footsteps of others. In retrospect, because this shaft was being sunk under entirely different conditions than those existing in South Africa, we were in fact venturing into an entirely new area of endeavour without properly recognizing this fact. It has occurred to me that others considering a similar type of job could benefit from our experience, especially in an assessment of the risks involved and how they compare to those encountered in an ordinary shaft. For comparison purposes, I would define an ordinary shaft as being sunk to a depth of 5,000 ft or less, and a deep shaft as one being sunk to a depth of between 5,000 ft and 8,000 ft. The sinking of the Creighton No. 9 Shaft has been de-

Jan 1, 1997

By Paul R. Weber

Open-pit mines are constructed in materials characterized by the complete range of geologic materials from the most recent alluvial sediments to hard intact crystalline rock. The determination of stable slopes in recent alluvium is in the realm of soil mechanics, an established engineering discipline, well founded on theoretical development and years of substantiating experience. The analytical tools of the soils engineer are chiefly derived from continuum mechanics wherein load-deformation response is governed by mass properties of the substance. At the other end of the spectrum, slopes in hard unweathered rock can generally be analyzed in a straightforward manner by the methods of discontinuum mechanics wherein the properties and orientations of joints control the response of the material. This approach is exemplified by the classical work of Terzaghi (1962). In between these two extremes is a gray area of material types which are composed of stiff soil and incompetent rock. This area is of importance to the mining engineer, since a large portion of open-pit mines is excavated wholly or in part into incompetent rock. This paper describes an approach to pit slope design in incompetent rock in which the material behaves essentially as a continuum. A wide range of geologic materials from stiff soil to poorly indurated sandstone and shale to crushed or weathered crystalline rock appear to fit in this category. These materials all possess certain mechanical properties which must be accounted for in a realistic assessment of slope stability. These properties include nonlinearity, s tress -dependency, and inelasticity. Further considerations involve residual stresses and time-dependent seepage pressures where groundwa.ter is present.

Jan 1, 1971

By Yutaka Mochida

OUTLINE Beginning in 1946, a careful geological survey was made of the Tsugaru Straits. In 1964, excavation of the exploratory tunnels were started to observe the characteristics of faults and rock formation directly, and to study construction methods of excavation and sealing water inflow. In March 1971, the investigation stages were over, and in April 1971, the construction project was authorized from the government. The geological features in the straits may be divided into three broad classes. One third consists of andesite on Honshu side. The other two thirds consists of tuff. The middle of the straits consists of tuff, so-called Kuromatsunai-layers. On Hokkaido side, it consists of tuff, called as Kunnui-layers. There are nine noteworthy faults on the route. Prior to the excavation of the main tunnel, the horizontal pilot tunnels and service tunnels are made. Exploratory borings are taken to confirm the geological conditions and the presence of gushing water. Groutings for sealing water inflow are carried out when necessary. In geologically bad conditioned sections such as disintegrated or fractured zones, special methods are applied. In geologically good zones, the tunnels are bored through using the same methods as for a mountain tunnel driving. The pilot tunnel being constructed at the sea bottom is under direct control of the Japan Railway Construction Public Corporation. The service tunnel and the main tunnel are being excavated by contractors.

Jan 1, 1981

By Steve Kral

More than 124,000 people involved in the mining and construction industries throughout the world poured into Las Vegas, NV in March for ConExpo-Con/Agg ’99. Show organizers said this triennial exhibition is the largest equipment show in the Western Hemisphere and one of the largest exhibition of any industry. “Clearly, Con-Expo-Con/Agg ’99 was one of the largest trade shows of any industry ever held in the Western Hemisphere,” said Bruno Benna, co-chair of the event. Attendees included mining industry representatives, including aggregates, and sand and gravel producers. In addition, many of the attendees work in the construction, reclamation, forestry, asphalt paving, landscaping and concrete industries. According to show records, about 52% of those attending were company presidents, vice presidents, chief financial officers or managers.

Jan 1, 1999

By P. Henderson, M. E. Morris, W. A. Johnson, F. D’Alessandro, D. Wilton

"The objective of this research is to develop and apply computer models to evaluate the potential lightning impacts on underground coal-mining. These models can then be utilised to assist in the design of effective controls. This project will provide a significantly improved level of knowledge and control over current lightning abatement techniques. The findings may also be applied to open cut and coal preparation situations. Computer modelling identified that by isolating cased boreholes from underground conductive media such as roof mesh, and placing spacings between roof mesh the risk of an ignition can be reduced by more than a factor of ten. These controls should be applied in conjunction with minimising the potential for a flammable atmosphere to exist underground and ensuring that there is no transmission medium for the lightning to reach the atmosphere. INTRODUCTION The objective of this research was to develop and apply computer models to evaluate the potential lightning impacts on underground coal-mining. These models could then be utilised to assist in the design of effective controls. If successful this project would provide a significantly improved level of knowledge and control over current lightning abatement techniques. The direct potential for harm from lightning has long been recognised for the surface facilities of coal mines. However recent events at Blakefield South in NSW on January 5 2011 (DTI, 2011) and at Sago mine in the USA in 2006 (MSHA, 2007) have suggested that there is potential for lightning to cause significant damage to the underground workings of a coal mine. A very detailed analysis carried out by as part of the MSHA investigation into the SAGO disaster by Sandia Laboratories identified at least ten other incidents over the past thirteen years where lightning had probably caused the ignition of a sealed goaf area of a mine (SANDIA, 2011). In addition there is a long history of lightning related incidents in South African coal mines (Geldenhuys, 1985). Fortunately in those cases no lives were lost. The event at Blakefield South has suggested that there may be the potential for ignition to occur in an active longwall goaf. The potential for a lightning strike to ignite a flammable atmosphere in an underground coal mine has been demonstrated from the past experience both here and overseas. It requires three things: • Lightning • A mechanism to convey the lightning underground to the flammable atmosphere • A flammable atmosphere."

Jan 1, 2016

By John Relser

The production processes that are developed in the mining and minerals industry are manufactured to be exposed to very aggressive environments. Chemical, abrasion, and impact expose structures and equipment, steel or concrete, to a significant deterioration. This causes damage and adds high costs to operations that can be reflected in the destruction of equipment and structures in the arrest of the production process, which becomes very costly. Also, there is the potential for personnel accidents, which would require large sums of compensation for an employee, thus directly harming the image of the mining operation and company. Manufacturers of paints and coatings that have major centers for research and development (R&D Labs) distributed globally have developed high-tech products for durable protection from the elements for structures and equipment used in the mining industry. The difference between these paintings and coatings and what is normally known as conventional paints (e.g., those called domestic or decorative), is its chemical composition, structured around polymeric components that have highly resistant, chemical and physical properties to cope with extreme conditions to which they are exposed. With this, and only this, longer life of components can be achieved for equipment and structures used in the production processes of the mining industry. Today, in addition to the important features mentioned, some manufacturers of the paints and coatings dedicated to this highly modernized process have invested large sums of money in developing new products that add operational elements to the painting process. These coatings provide added value and significant performance to companies mining operations and that we can describe in three fundamental concepts:

Feb 1, 2014

By Neil F. Archer

Due to the increased chance of violations and shutdowns by the U.S Occupational Safety and Health Administration(OSHA) and the U.S. Environmental Protection Agency (EPA), a company can save itself problems by taking control of the dust caused by conveying material. A complete dust-control policy can keep these emissions confined, sealed and suppressed, protecting the environment from fugitive, airborne dust. Material handling and processing, storage and traffic are the major dust producing sources. All industries that convey dry, light material need a dust control system.

Jan 1, 2003

By Rolf Christiansson, Daniel Johansson, Urban Åkeson, Henrik Ittner, Mats Olsson

"This paper presents two recent studies on the extent of blast damage after excavation in crystalline rock. The Swedish Transport Administration and the Swedish Nuclear Fuel and Waste Management Company (SKB) are both under regulations to limit excavation damage during construction of tunnels. SKB is also required to limit the Excavation Damage Zone (EDZ), as this could be a potential flow path for radionuclides in the planned repository for spent nuclear fuel. Presented in this paper are investigations of blast damage from three tunnel sites, a road tunnel, an experimental tunnel in Äspö Hard Rock Laboratory and an underground subway depot. As expected the fractures resulting from the bottom charge are both longer and more frequent then those mapped in the column charge. The results show that the requirement to limit blast damage according to Swedish regulations was fulfilled for the column charge at the three studied sites.1 INTRODUCTION The Swedish Transport Administration (TRV) and The Swedish Nuclear Fuel and Waste Management Company (SKB) have both recently completed studies related the extent of blast damage from modern explosives after excavation. SKB studies focused on blast damage from pumpable emulsion explosives for underground construction (Ittner and Bouvin 2015) and hydraulic connectivity in the EDZ (Ericsson et al. 2015). TRV had a broader focus with different types of explosives including blasting for both road cuts and tunnelling with pumpable emulsion explosives. Investigations by means of geophysics were also conducted (Olsson et al. 2015). High demands on perimeter control and excavation damage is usually required for underground constructions with a long operation time, such as public tunnels for transport or underground repositories for nuclear waste. This paper presents the findings of recent Swedish studies and aims to discuss the topic in a broader context."

Jan 1, 2016

By Jerry Williams

GEORGE WEINMAN: At this time, our co-chair, Jamie Davis from Phelps Dodge, will come to the podium. JAMIE DAVIS: Our next speaker is Jerry Williams from Phelps Dodge, Morenci. Jerry is the maintenance planning supervisor and is in charge of preventative maintenance and maintenance scheduling. Jerry's group uses predictive tools to monitor and predict the equipment failure throughout the mine, from pumps to shovels to motors, you name it. The title of Jerry's talk is "If You're Not Using Predictive Tools, You're Behind the Curve." I’ll turn it over to Jerry.

Jan 1, 1998

By G. Biles

The Eskay Creek Mine, a high-grade gold and silver underground mine in northwestern British Columbia started operations in late 1994. For the first three years of operation, ore was crushed to minus 2 inch; blended to satisfy smelter terms and direct shipped to smelters in Japan and Canada. Before commencing the above operations, preliminary evaluations had indicated that an extremely complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. Subsequently markets for raw ore were identified and underground mining and ore transportation operations, at a nominal production rate of 300 tonnes per day, were commenced. Exploration diamond drilling in 1995 and 1996 discovered additional lower grade mineralized zones, which are less economic or uneconomic as direct shipping ore. Testwork demonstrated that these lower grade zones could be upgraded to marketable concentrates in a simple flotation mill. The mill was built in 1997 and has been in operation since late 1997. The mining rate now has increased to 400 tonnes per day including 250 tonnes per day of the direct shipping ore and ISO tonnes per day of the mill ore. Prime Resources Group Inc. wholly owns the Eskay Creek Mine. Homestake Canada Inc. owns 50.6% of Prime's shares and manages and operates the mine on Prime's behalf. This paper discusses the mining and milling operations as well as ore shipment and smelter contracts' administration.

Jan 1, 1999

By William Gleason

"Government support for Canada’s mineral industry was on full display during the Prospectors & Developers Association of Canada (PDAC) conference in Toronto, ON, Canada on March 3-6. First, there was the announcement of the five-year extension of Canada’s Mineral Exploration Tax Credit (METC), the first multi-year extension of the METC since its inception in 2000. Canada’s Minister of Natural Resources, Amarjeet Sohi, added to that support when he spoke at the opening keynote session and announced the Canadian Minerals and Metals Plan (CMMP), a plan that aims to map out the future of the industry in Canada. Finally, the support for the mining industry was buttoned up with a visit to the conference by Canadian Prime Minister Justin Trudeau.More than 25,000 people from 135 countries attended the annual conference that features a robust trade floor, technical sessions and an investors’ exchange that aims to put mining companies in touch with potential investors. Mining companies and ambassadors from nations around the world are given the opportunity to present to small audiences throughout the conference and this year PDAC was able to sway the Prime Minister to speak on its behalf.Trudeau sat down with PDAC President Glenn Mullan on March 5 to talk about the METC extension and a host of other issues important to the Canadian and global mining industry, giving the home country a bit of a profile advantage when it came to making a pitch to investors.Trudeau entered the week of the conference in the midst of the most serious political scandal of his career and was defending himself against accusations of political interference with the top prosecutor in the land over a criminal case involving one of Canada’s largest companies, SNC-Lavalin. During the question-and-answer session at the Metro Toronto Convention Center, Trudeau seemed more than happy to keep to the discussion about mining. He spoke favorably about the industry during the half hour conversation and praised the industry for its work with Indigenous people as well as its efforts to advance technology and innovation. He made a case that Canada is a safe and reliable place for investment in the minerals sector.“We are at a time of change right now, of transformation with new technologies and global supply chains, and everyone is trying to adjust to the new realities that have accelerated so much these past years,” Trudeau said. “What we are trying to do as a country and what you have done as an industry is to try to look at where things are going – go to where the puck is going to be, not where it is. You, as an industry, know that investments in innovation, research, science — investment in technology and partnerships with Indigenous communities are all things that are going to give you opportunities to be competitive in the coming years.”"

Apr 1, 2019

By M. K. Larson, J. K. Whyatt

Proper employment of numerical stress analysis design tools is based on the demonstrated ability of a model to capture key elements of the geologic site model and accurately simulate how these elements interact with a mine design. While these tools have progressed markedly, they are, at heart, a gross simplification of the abundant complexity of a natural setting and its response to mining. A generic deep longwall site model was developed that includes aspects of the geology of deep coal mines in the Wasatch Plateau and Book Cliffs coal fields of Utah. The site model contains a set of common features and observations of how these features typically respond to mining. This site model was the basis for evaluating use of empirical, boundary element and volume element stress analysis tools to analyze the distribution of stress around a deep longwall panel. More specifically, this evaluation examined shifting of stress to panel abutments and gob, distribution of stress in the abutment and deformation and failure of bridging strata. Measurements of abutment stress changes at two sites in the Wasatch Plateau region were used to illustrate model calibration. Overall, these comparisons highlight the considerable differences between methods. Volume element tools can incorporate considerable detail and have fewer underlying assumptions, but this detail carries a considerable computational cost. Boundary element tools are much more efficient. However, this efficiency comes at the cost of added assumptions. These assumptions were challenged by the presence of a strong sandstone unit in the overburden, leading to boundary element results that depart significantly from volume element results. Empirical rules are the simplest, but are even more burdened by assumptions, many of which are implicit in underlying cases. Insight into the nature and impact of underlying assumptions in each method is essential to the proper use of results in mine design.

Jan 1, 2009

By Evan Brinkerhoff, Steve Chorley

The largest hard rock TBM ever to bore in the USA, an 11.6 m diameter Robbins Main Beam TBM, recently underwent a planned in-tunnel diameter change to a more compact 9.9 meters. The first-of-itskind conversion process for the Main Beam TBM was undertaken 2.8 km into the bore and was not done inside a shaft or pre-excavated portal. This paper will detail the unique dual-diameter machine designed for the Mill Creek Drainage Relief Tunnel in Dallas, Texas, USA, machine performance, and successful size conversion process that took place in early 2021—a process that utilized the four C’s of construction to enormous benefit: Communication, Cooperation, Collaboration and Coordination.

Dec 1, 2022

By U. K. Custred

In 1973, the United States production of marketable phosphate rock set a record in excess of 42 million tons. This production rate is expected to continue to increase, due to the growing international requirement for fertilizer, at a rate exceeding 5% per year well into 1977. This trend contrasts sharply with the reduced phosphate rock production levels of the 1966 - 1971 period. The natural consequence of this growing phosphate rock market is an evaluation of the variety of means whereby plant capacity can be most effectively increased. One approach toward increased plant production capacity is through large capacity flotation cells provided they can be successfully applied to the recovery of the relatively coarse product which is characteristic of the phosphate rock feed. This paper will summarize the results of a nine month evaluation test program, conducted at the Haynesworth Mine at Bradley, Florida in which the flotation circuit "specific capacity" (tons feed/ft.2 floor space) and "specific input power" (Hp/ton feed) were determined, and the feasibility of achieving economically acceptable concentrate grade and recovery levels was demonstrated, using large, high capacity, flotation cells.

Jan 1, 1974