Search Documents

By M. R. Shahan, W. R. Reed, P. Zhang, J. P. Rider

Roof bolter operators may be exposed to high respirable dust concentrations on continuous miner sections with blowing face ventilation when bolting is performed downwind of the continuous miner. One solution to reduce the high respirable dust concentrations is to use a canopy air curtain (CAC) to deliver clean air from a filtered blower fan directly to the bolter operators under the canopies. The influence of CAC installation in the airflow and dust dispersion around the location of the roof bolter operator can be evaluated by using computational fluid dynamics (CFD). This study, performed by the National Institute for Occupational Safety and Health (NIOSH), considers two scenarios: (1) a roof bolting machine in the center of the entry for installation of the fifth row of bolts from the face, and (2) a roof bolting machine positioned close to the face for the installation of the last row of bolts. In both scenarios, the bolting machine is placed in an environment which contains 6.0 mg/m3 of respirable dust and is ventilated by a blowing curtain with 3,000 cfm (1.42 m3/s) of air. This environment is used to simulate the roof bolter machine operating downstream of a continuous mining machine. Two operation positions are simulated at the same bolting location: dual drill heads in the inward position for two inside bolts; and dual drill heads in the outward position for two outside bolts. The influence of the CAC on airflows and dust dispersion is evaluated with the CAC operating at 250 cfm (0.12 m3/s). INTRODUCTION Roof bolting machines are used to drill bolt holes into the roof of an underground mine at specified patterns and to install roof bolts to secure the roof from falling. At times, the roof bolting machine is also used to install rib bolts; however, only the roof bolting operation was considered in this simulation. Though the roof bolting operation drastically improved the safety of miners from roof falls, some roof bolter operators are experiencing health problems associated with respirable dust. Based on recent statistics [1], following a low point in the late 1990s where the prevalence of coal workers’ pneumoconiosis (CWP) in miners with 25 years or more tenure was approximately 5%, CWP now exceeds 10% for miners with 25 years or more of tenure. In central Appalachia (Kentucky, Virginia, West Virginia), 20.6% of long-tenured miners have CWP and 4.5% have progressive massive fibrosis, the most severe form of CWP. CWP, also known as black lung, is an occupational respiratory disease that has no cure and can ultimately be fatal. The only way to prevent the incidence of black lung is to eliminate miners’ exposure to respirable coal mine dust. Current U.S. regulations require that the overall respirable dust concentration to be 1.5 mg/m3 or less for a full-shift sampling if respirable quartz is not present; otherwise, the standard is 10 divided by the percent quartz (not to exceed the 1.5 mg/m3 respirable dust standard) [2, 3].

Jan 1, 2019

By B. E. Davis, D. A. Stanley, C. E. Jordan

A prototype expert advisor was developed by the U.S. Bureau of Mines to systematically offer advice on the control of a Florida phosphate operation. The PC based system receives input from remote sensors for circuit parameters such as feed rate, reagent addition, and pH and from operator entered information such as the quality of the concentrate and tailings in each of the coarse, fine, and amine flotation circuits. The computer evaluates the information using rules obtained from industry representatives and Bureau flotation experts. Recommended actions and questions are displayed to quickly guide the operator to a problem within the flotation circuit and suggest a solution. This process control system could provide more uniformity among the flotation operators and also serve as a trainer for new operators. In addition, it represents a step toward fully automated systems for phosphate flotation.

Jan 1, 1990

By George K. Schenck

INTRODUCTION Recent advances in high-pressure water jet technology can be effectively employed in mining and tunneling. The new equipment is based on available industrial hardware such as pumps, nozzles, and rotary swivels and seals, and is compatible with present mining and tunneling techniques. Principal advantages of water-jet assisted cutting relative to standard cutting are higher production rates, lower dust levels, and reduced fines. When used on rock and coal miners, water jets mean that relatively smaller and cheaper machines can be purchased. If properly applied, the combined effect is lower cost and significantly improved health and safety. While commercial use of high-pressure water blast cutting and extraction of rock (and concrete) already has a firm foothold in Europe, application of this new technique is just beginning in America. This paper begins with current American applications of high-pressure water jets for drills, for slotting and channeling machines, and then discusses the emerging technology for initiating rock failure in conjunction with drag bits on coal plows, continuous miners and boom-type miners (roadheaders). The focus of this paper is use of high-pressure water jets for cutting rock. High-pressure water jet cutting utilizes water above 70 MPa and currently reaches to 300 MPa and above. Some informatfon is included on low pressure "wethead" coal shearers and boom miners with water pressure to about 15 MPa.

Jan 1, 1983

By Anuradha Khetwal, Sandeep Khetwal, Andrea Panciera

The observation method is a design optimization approach for the drill and blast method in tunneling. This method includes first identifying the hazard scenarios through site investigation, formulating suitable solutions, obtaining feedback during construction, and finally using that data to optimize the design methods. This paper illustrates the application of the observational method for T-48, a railway tunnel project in the Himalayas. It is a 10.2 km long tunnel with a parallel escape tunnel and 26 cross passages. The use of observational methods in this project optimized the overall tunnel design and considerably saved the overall project cost.

Jun 23, 2024

By James E. Lonergan

Linear goal programming is a multi-objective optimization technique where the constraints of a linear programming formulation of a problem are considered as additional objectives. The optimal solution is the one that comes closest to satisfying all the objectives. An interactive computer program was written to utilize this technique in solving the feed blending problem faced by power plants de- pendent on multiple sources of coal supply. This program determines the amount of coal from each supplier to utilize in the blend. Examples of the use of the program in both long and short term coal procurement planning scenarios are given.

Jan 1, 1984

By D. C. Torre

Ever since the early '60's there have been efforts to develop and produce reliable continuous haulage systems capable of taking the full output of a continuous miner and transporting it, in one continuous flow, from the face to the tipple. The majority of the continuous haulage systems which have been most successful to date were placed in operation in the early '70's and were all of the bridge conveyor type, usually consisting of bridges and mobile bridge carriers attached at the inby end to the continuous miner and at the outby end to the panel conveyor itself. These successful bridge conveyor type continuous haulage systems were, and continue to be, either of the belted or chain type. Undoubtedly, the most successful belt type continuous haulage systems are those manufactured and marketed by the Long-Airdox Company. Until early 1977, the most successful chain conveyor type haulage systems were manufactured and marketed by Jeffrey Mining Machinery Division. In 1977, Long-Airdox reentered the market with a chain type system to complement its belted system. I say "reentered" because the original bridge type continuous haulage system was introduced to the coal mining industry in the early '60's by the old Long Company, a predecessor of the current Long-Airdox Company, and those original units were of the chain conveyor type.

Jan 1, 1981

By A. J. Hendron, J. E. Monsees

INTRODUCTION This paper is the outgrowth of work done by the authors to prepare the seismic design criteria for underground structures on the Southern California Rapid Transit District (SCRTD) Metro Rail Project. It is a follow-on to a similar paper presented at the October, 1984, ASCE National Convention (17). For design, the earthquake-induced distortions recommended herein are to be added to the normal static loading conditions for the underground structure. This design approach has been used by 18 section designers on the SCRTD Project. Preliminary results from two- and three-dimensional finite element solutions have partially verified the approach. Areas where additional research is needed for special cases are identified. EFFECTS OF EARTHQUAKE The effects of earthquakes on underground structures may be broadly grouped into two general classes -shaking and faulting. In response to earthquake motion of bedrock (shaking) , the soil transmits energy by waves. Seismologists identify various types of earthquake waves, but underground engineers are generally interested in the effects of transverse shear waves which produce a displacement of the ground transverse to the axis of wave propagation. The orientation of propagation is generally random with respect to any specific structure. Waves

Jan 1, 1985

By D. Kozelj

Introduction The porphyry copper deposit “Borska Reka” is the biggest undeveloped deposit in the Timok Magmatic Complex (TMC). Total reserve calculated manually is 611 Mt (cut-off grade 0.3% Cu) of 0.62% Cu, 0.21 g/t Au and 1.81 g/t Ag and 869 Mt of 0.58% Cu, 0.14 g/t Au and 1.11 g/t Ag using software. But since several deep drill holes are suspended in high grade (0.7% Cu) porphyry, total reserves could exceed 1Gt. The massive sulfide is also detected in the central (12 m at 4% Cu) and the bottom of porphyry style. Deposit was discovered during geologic exploration of deeper part of the Bor copper and gold deposit, i.e. area of high sulfidation with dominant massive sulfides. During exploitation of massive sulfide, constant explorations were carried out aimed at the expansion of reserve and discovery of new ore bodies. In that way, porphyry copper mineralization was discovered without knowing in the beginning that it was different mineralization type in regard to the ones that had been already identified and exploited. Vertical extension of porphyry is 0 m up to -1000 m sea level and not contoured along plunge. In the very beginning (1976), the exploration was focused on the shallow part of porphyry. That is because block caving method of massive underground mining was not developed at that time. Up to 1999, most of activity was related to underground exploration up to level -395 m. Geographic position The Bor deposit is located close to the industrial and University town Bor, which has over 50,000 inhabitants (census made in the year 2002). Apart from the Bor Mines, industrial complex of Mining & Smelting Basin Bor (RTB) comprises also a copper smelter (installed capacity up to 160,000 tons of blister copper) and tank house, copper wire factory, copper tube factory etc. Currently, RTB Bor is under privatization process that is going to be completed by the end of 2006. Up to date, over 20 companies have bought tender documentation.

Jan 1, 2007

By Ihsan Berk Tulu, Gaobo Zhao, Deniz Tuncay, Syd S. Peng

Longwall mine instrumentation for measuring abutment stress distribution, mining induced immediate roof stress change and deformation, and primary/secondary support loads and deformations provides critical guidance for the design of gateroad chain pillars and roof support. Field measurement results are also recognized as the best way to calibrate numerical models that have been used to study the failure and support mechanisms. International Conference on Ground Control in Mining (ICGCM) started in 1981 and since then, there were 26 papers published in the proceedings discussing the stress and load measurements as the face advanced using various field instrumentation techniques. The focus of this paper is on summarizing the analyses of the data published in these papers. Stress/load change monitoring included the following categories: gateroad chain pillar, abutment pressure, bolt load, and pre-driven recovery room. The data shows that the magnitude of stress changes as the face advances varies considerably from panel to panel and mine to mine. However, regardless of types of stress changes, pillar stress, abutment pressure, and bolt load, there exists a rough trend of stress increase as the face advances, generally consisting of three stages, i.e., stress/load (1) initially increases steady or slowly, (2) increases rapidly, and (3) increases reaching the peaks and dropping down slowly or sharply. The stress/load increases start earlier during the second panel mining and are larger than the first panel mining. This review makes it easy for the interested persons to find valuable data for other similar projects.

By M. Niec

Poland lies at the junction of three geologic provinces: the East European Precambrian platform, the Middle European Paleozoic platform, and the Alpine orogenic belt comprising the Carpathian Mountains. However most of the rocks that contain mineral deposits and many of the recently explored and mined deposits are commonly hidden under thick overburden, sometimes up to over 500 m thick. The discovery of these mineral deposits was due to the combination of geologists talents for inference and the keen interpretation of geophysical data ultimately tested by drilling. Examples of such use of the state-of-the-art geology include the following: 1. Sedimentologic and paleogeographic reconstructions led to the discovery of 8.8 Gt of bituminous coal under 500 m of Jurassic and Cretaceous cover in the Lublin basin, 2. Tectonic and paleogeografic data suggested a potential for discovery of burried Upper Permian copper de-posits on the Foresudetic monocline; subsequent exploration discovered 75 Mt of copper and 0,17 Mt of silver, 3. Geological interpretation of gravity and magnetic da-ta combined with sedimentologic data and regional subsur-face geology resulted in the location of 1.3 Gt of Fe-Ti-V ore in the Precambrian basement of northeastern Poland under -500 m of cover 4. A combination of metallogenic theory and geological interpretation of regional geophysical mapping led to the discovery of Caledonian-Hercynian granites and grano-diorites with accompanying porphyry-type Mo-W-Cu ores below 300 m cover on the northeastern border of the Upper Silesian coal basin 5. Tectonic reconstructions based on gravity and seismic data combined with theory on the origin of native sulfur led to the discovery of 1.0 Gt of native sulfur under cover up to 300 m thick. Five deposits were found at the northern margin of the Carpathian Foredeep. The other deposits found include lignite, polyhalite, lead-zinc ores.

Jan 1, 1996

By R. Benito

This paper describes the development of a life-of-mine schedule (LOM) for one of the world's largest known sedimentary copper-cobalt districts located in the Katanga Province, Democratic Republic of Congo (DRC). A particular feature of the Tenke Fungurume LOM schedule is the considerable number of pits/phases for scheduling, each competing to provide the best ore available to a capacity-constrained process facility. This paper discusses the LOM scheduling objectives and constraints, data preprocessing steps such as ore binning, block aggregation and clustering analysis as a scheduling aid, the mine scheduling approach and results and conclusions. Mining Engineering, 2011, Vol. 63, No. 8, pp. 39-47. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Colin Irwin, Adrian Naranjo-Castillo, Christopher Petta, Eric Zarobila

The Shoreline Consolidation Sewer is a CSO control project in Cleveland, Ohio that requires the installation of 5,000 feet of 72-inch inside diameter pipe using microtunneling methods. After award, the contractor submitted a value engineering proposal to eliminate two deep shafts and install the tunnel in two drives instead of four. In an example of successful collaboration, owner, contractor, and engineer worked together during the initial construction stages to modify the design and update the contract documents. This paper examines the importance of exible requirements in contract documents and a collaborative environment between all parties to successfully deliver a project.

Jun 23, 2024

By F. J. Sotillo

"Scrubbing both horizontal (drum) and vertical (attrition) are considered simple unit operations in the beneficiation of phosphate ores. In general, the operating conditions are fixed at high solids content based on the experience of the engineering or equipment manufacturing company responsible of designing this beneficiation step. Nevertheless, scrubbing is a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes, break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Therefore, it is considered that as high solids content as possible should be used to enhance particle-particle interactions (impact and rubbing) without taking into consideration the rheology of the system. However, scrubbing unit operations design requires studying the balance between the increase of particle-particle interactions with the cushion effect that may occur when slimes, clays and fines decrease the availability of free water increasing the apparent viscosity of the phosphate slurry up to that of a paste consistency. This paper presents data from laboratory tests to determine the best operating conditions for the design of these unit operations based on the highest P2O5 grade obtained with the lowest impurities for different size fractions. INTRODUCTION In the beneficiation of phosphate ores, unit operations such as horizontal scrubbing (drum) and vertical scrubbing (attrition) are considered simple unit operations. Therefore, little attention is given to the design of horizontal and vertical scrubbing during the basic engineering studies, and the detail engineering stage, the manufacturers recommending “standard” units and operating conditions based on their experience. Due diligence of several beneficiation phosphate plants at industrial scale indicates that a deficient scrubbing of the phosphate ore results in significant problems in downstream unit operations, such as classification, clarification, gravity separation, magnetic separation, flotation, dewatering, and filtration. Scrubbing is in fact a complex unit operation designed to clean the surfaces of phosphate mineral particles of slimes (clays and fines), break loose weak inclusions or attached particles of impurities, and break aggregates of clayish material. Two phenomena occur, the particle-particle interaction (impact and rubbing), and the rheological effects of releasing significant amount of fines into the slurry. Therefore, high solids contents are recommended to enhance the particle-particle interactions, which may result in a change in the rheological regime of the system due to the slimes, clays, and fines decreasing the availability of free water. This increases the apparent viscosity of the system up to that of paste consistency resulting in a cushion effect that suppresses scrubbing. Under these conditions, not all fines are release and rejected (deslimed), downstream unit operations being affected by the release of clays, resulting in P2O5 losses."

Jan 1, 2017

By M. E. Buzon, M. E. Gunter

Talc has been the focus of recent civil litigation based on claims that asbestos minerals exist in talc deposits and therefore have caused asbestos-related diseases in those who have regularly used talc products. Such litigation, and ensuing confusion over the petrology and asbestos content of these deposits, challenges the talc mining industry in Montana and elsewhere in the world. The talc deposits in southwest Montana were formed by hydrothermal alteration of dolomitic marbles and are still actively mined. In general, talc formed by hydrothermal alteration of preexisting carbonate rocks is known to be nearly monomineralic and lacking in amphiboles. This paper includes data from analyses of representative ore samples from this mining region in southwest Montana. The results conclude that the presence of asbestos minerals — both amphiboles and chrysotile — is unlikely and that the ores are nearly monomineralic, as expected. Samples were characterized using a suite of analytical methods, namely, powder X-ray diffraction, X-ray fluorescence spectroscopy and electron microprobe analyses, which allowed us to determine the minerals present and the formation process. Our data and interpretations suggest that previous identification of asbestos minerals in these deposits is not accurate.

Jan 1, 2018

By M. E. Buzon, M. E. Gunter

Talc has been the focus of recent civil litigation based on claims that asbestos minerals exist in talc deposits and therefore have caused asbestos-related diseases in those who have regularly used talc products. Such litigation, and ensuing confusion over the petrology and asbestos content of these deposits, challenges the talc mining industry in Montana and elsewhere in the world. The talc deposits in southwest Montana were formed by hydrothermal alteration of dolomitic marbles and are still actively mined. In general, talc formed by hydrothermal alteration of preexisting carbonate rocks is known to be nearly monomineralic and lacking in amphiboles. This paper includes data from analyses of representative ore samples from this mining region in southwest Montana. The results conclude that the presence of asbestos minerals — both amphiboles and chrysotile — is unlikely and that the ores are nearly monomineralic, as expected. Samples were characterized using a suite of analytical methods, namely, powder X-ray diffraction, X-ray fluorescence spectroscopy and electron microprobe analyses, which allowed us to determine the minerals present and the formation process. Our data and interpretations suggest that previous identification of asbestos minerals in these deposits is not accurate.

Jan 1, 2017

By S. K. Kawatra

Outokumpu Electronics has designed a new on-line coal slurry ash analyzer, based on an instrument developed at Michigan Technological University. The primary goal was to build an accurate instrument at the lowest possible cost. The instrument determines ash content from measurements of x-ray backscatter, iron Ka fluorescence, and low-energy y-ray absorption. It is capable of measuring the ash content with a standard error of 1.1% ash over an analysis range of 9-21% ash and 7-22% solids. The analyzer was tested on coals from United States, Poland, Great Britain and the USSR.

Jan 1, 1992

By D. S. Bubar

This presentation will represent a diversion from the central theme of Cordilleran geology, in both time and space, as we move 2,000 miles east of Spokane to eastern Canada, specifically the province of Quebec, to discuss a major new Archean-age volcanogenic massive sulphide deposit called Louvicourt. The deposit is located in the Val d'Or camp in the prolific Abitibi Greenstone Belt some 400 miles north of Montreal. It was discovered by Aur Resources in June, 1989 on a property operated under the terms of a joint venture with Louvem Mining, a Quebec company controlled by Ste. Genevieve Resources Inc. of Montreal. As a geologist, I am proud to be able to describe Louvicourt as a geological discovery, as it was found by doing systematic deep diamond drilling based on a geological concept. The deposit is essentially blind from surface and lay undiscovered for the 10 years that the Louvem mine was in production just 2,000 feet away from its easternmost workings.

Jan 1, 1991

By Lynn Salvati, Colin LaVassar, Loic Galisson, Joel Theodore, Lynette Sla

"Sound Transit’s University Link and Northgate Link projects will add 6.75 miles (10.9 km) of twin-bored tunnel to Seattle’s light rail system, extending the route north from downtown Seattle. The tunnels are being constructed primarily in glacial soils using pressurized-face tunnel boring machines. Cover over the tunnel alignment varied from 13 feet to over 300 feet (4–91 m). Since the tunnels are located in densely populated urban areas, controlling ground movements and monitoring settlement were essential to success of these projects. Hundreds of geotechnical instruments, including extensometers, surface settlement points, and near-surface settlement points, were used in both projects to monitor settlement. The observed data were compared to settlement predictions made prior to tunneling, and analyses performed to update empirical factors to better estimate settlements. Recommendations for designing efficient and cost-effective settlement monitoring programs are provided based on the review of the monitoring data and analyses.INTRODUCTIONThe paper includes data from Sound Transit’s University Link and Northgate Link projects. These projects will add 6.75 miles of twin-bored tunnel to Seattle’s light rail system. The tunneling for University Link will extend the light rail system from downtown Seattle to the University of Washington. Tunneling from downtown Seattle to the Capitol Hill Station was completed under the U230 contract, and tunneling from the Capitol Hill Station to the University of Washington Station was completed under the U220 contract. The Northgate Link extension will extend the light rail line north of the University of Washington, including approximately 3.5 miles (5.6 km) of twin tunnels between the University of Washington Station and the Maple Leaf Portal and two stations, U District Station and Roosevelt Station. Tunneling for the Northgate Link project is still underway as part of the N125 project. At the time of writing, tunneling from the Maple Leaf Portal to Roosevelt Station has been completed. Therefore data labeled as N125 in this paper only include the portion of the alignment from the Maple Leaf Portal to Roosevelt Station."

Jan 1, 2016

By K. Dagdelen

The definition and shortcomings of traditional cutoff grades are discussed. The concept of optimum cutoff grade policy which maximizes the Net Present Value (NPV) of annual cash flows coming from a mining project is introduced within the basic framework outlined by K. F. Lane. Several examples are used to demonstrate the shortfalls of cutoff grade policies obtained by various heuristic optimization techniques. An algorithm to obtain an optimum cutoff grade policy which maximizes the NPV of a project is given and described in detail.

Jan 1, 1993

By Hans Svensson

INTRODUCTION The Alimak method of raising (Fig. 1) was intro¬duced in 1957. Because of its flexibility, economy, and speed, it soon became the most used system of raising in the world. With the same unit, raises of various areas, inclinations, and lengths can be driven. Air-motor¬-driven raise climbers normally are used in mines with short raises (Fig. 2). For longer raises electric or diesel-¬hydraulic drives are used. The Alimak raise climber is designed entirely in ac¬cordance with the instructions of the Swedish Board of Industrial Safety (Arbetarskyddsstyrelsen). There are good margins of safety concerning the breaking strength of the material and the raise climber comprises safety devices and features that practically eliminate the risks of accidents. The drive gear of air-driven climbers is equipped with an air-operated brake which is automatically activated when air for the motors is shut off. There is a safety device which activates automatically at overspeed and a speed-regulated brake for descent by gravity, by which the raise climber can be taken down to the bottom of the raise in case of cutoff of the air supply. The raise climber climbs along a pin rack welded to a guide rail which also comprises pipes for air and water. The guide. rail can be extended by using 1- or 2-m (3.2¬or 6.4-ft) sections as the driving progresses. Each guide rail section is bolted to the rock wall by special expan¬sion bolts of Alimak design. Men ride up to the face in the cage, traveling com¬fortably and easily while material is transported on the platform. There is no dangerous climbing up ladders. The men are well protected during ascent and arrive in good condition at the face. The greatest advantages of raise climber systems are flexibility and versatility. The equipment provides a comfortable working position in vertical as well as in¬clined raises of any area and length. The direction may

Jan 1, 1982