Search Documents

By M. Gouet-Kaplan, J. A. Finch, S. Gélinas

Methylisobutyl carbinol (MIBC) and methoxy polypropylene glycol (Dowfroth 250) bubble thin films were characterized by composition and thickness determinations, using FT-IR spectroscopy and UV-Visible spectrophotometry, respectively. The infrared investigation indicates that the role of frother molecules in creating bubble thin films is based on their effectiveness in inducing H-bonding reorganization of the surrounding free water molecules into a coherent network. From UV-Visible interference patterns, it is found that MIBC forms films with a measured critical end thickness of less than 160 nm, compared to 612 ± 30 nm for Dowfroth 250. The observed values of the free water layer thickness are comparable at 5.65 ± 0.28 µm for MIBC and 6.75 ± 0.34 µm for Dowfroth 250. A higher stability of an MIBC bubble over a Dowfroth 250 bubble is related to the different polarization and orientation of the molecules sustaining the boundary surface water network. The findings are used to explain the different action and associated froth characteristics of the two common industrial frothing agents.

Jan 1, 2006

By Ernest H. Gilmour

Introduction An earth science teacher at the junior high school level has the potential of working with 450 students per year. And these young people are at an age where they can be properly informed about the importance and necessity of a viable, domestic minerals industry. It was with this philosophy that a course was developed at Eastern Washington University for science teachers entitled, "The Minerals Industry of the Pacific Northwest." The two-week course is sponsored by the Northwest Mining Association and the Idaho Mining Association. It was first taught during the summer of 1971 and will be taught during the summer of 1986 for the sixteenth straight year. It is a two-week mini-version of the very successful six-week course taught at the Colorado School of Mines. In 1971, Russ Chadwick was President of the Northwest Mining Association. He suggested that such a course should be developed and offered at Eastern. It was determined that tuition scholarships would be necessary. This would ensure that a reasonable number of teachers would register for the course. Say a teacher has five classes a day, with 30 students in each class. Some 150 students come into contact with that teacher each term. With three terms a year, an instructor works with about 450 students per year. So, with 20 teachers in the course, it was possible that 9000 students a year could learn from our informed teachers. And now, after 15 years, more than one million students have learned about the minerals industry from teachers who have completed the course. The course is designed to take the teachers through all aspects of the minerals industry. Most of the lectures are given by the working geologists and engineers who talk about their jobs in the industry. This is extremely important for the credibility of the course. The teachers realize that the lecturing professionals really believe in what they profess. Industry fundamentals The course begins with a lecture on the need for minerals in a modern society. Most of the teachers do not realize how critical minerals are to every aspect of our daily lives. The lecture is followed by the US Bureau of Mines movie, "Minerals Challenge." An exploration geologist then discusses what is involved in the exploration for a mineral deposit. This includes a case history that the geologist has actually been involved in

Jan 9, 1985

By W. G. Pariseau

Introduction Caverns of 50 m in linear dimension at depths below 2300 m with a life of more than 25 years are proposed for the next generation of water-filled neutrino detectors. Little precedent exists for excavations in such an extreme environment, although some guidance is available from mining experience at great depths, for example, in South Africa, in Canada and at the former Homestake Mine in the U.S.A. Unlike mining for ore, there are choices available in the construction of such caverns that may mean the difference between success and failure. These choices should be informed by rock engineering principles. Recently proposed guidelines for orientation of brick-shaped caverns where the long dimension is a small multiple of the short dimension indicate that the most favorable orientation is with the long and short dimensions parallel to major and minor preexcavation principal stresses (Pariseau, 2005). Numerical analyses at reduced strength indicate some yielding at cavern walls should be expected but that an equilibrium state is quite possible and is aided by arching the back into a spherical dome when the cavern is an empty cylinder (Tesarik and others, 2002). The same indications of stability occur with brick-shaped caverns. However, the most dangerous situation occurs during the excavation sequence to final cavern dimensions. There are any number of excavation sequences that lead to the same final cavern shape, so there is an opportunity to partially optimize the sequence with construction guidelines that minimize peak stress concentrations during construction. This contribution discusses three practical excavation sequences that lead to the same brick-shaped cavern in the strong, massive Yates formation at the Homestake Mine where considerable rock mechanics data has accumulated through the years(e.g., Pariseau, 1985, Pariseau and others, 1995) and where actual mining on the 8000 Level indicates a strong possibility of successful investment in the next generation of large, deep neutrino detectors. The main results are: (1) a favorable brick-shape is one with dimensions in the same proportion as the preexcavation principal stresses (compressionpositive), and (2) favorable orientation of the most extreme but temporary shape of excavation is also best for the construction sequence. Analysis results from a mix of Homestake Mine data and possible excavation geometry illustrate the advantages of these guidelines.

Jan 1, 2006

By L. B. Bramlett

The Archean (2.65 b.y.) aged Canning Stock at Copper Mountain, Wyoming contains an average of 20 ppm U. The North Canning and Fuller deposits occur within the enriched interior of the stock. Post-Laramide development of super gene enrichment blankets occurred in wide (25- 100 m) crushed zones. Hematite and chlorite accompany pyrite and sooty pitchblende in the mineralized zones. Reduction mechanisms proposed for deposition of pitchblende are: 1) sulfides, 2) hydrocarbons, 3) bacteria, 4) the water table, or 5) some combination of these. Abundant tar- type organics appear to have preserved the enrichment blankets from degradation. Trace element and radiometric data define target zones, but exploration models focus on favorable structure.

Jan 1, 1980

By G. Deissman, S. Kistinger

For the last 15 years environmental Life-Cycle Assessments (LCA) have increasingly been used to evaluate the environmental performance of industrial processes and products and have been employed as a basis in decision making processes in the public and industrial sector. However, assessment methodologies for environmental protection measures and reclamation/remediation measures with respect to their consumption of natural resources are generally poorly developed. In this presentation a methodology for LCA of environmental protection measures and remedial actions, respectively is suggested, using the remediation/reclamation of mining sites as an example. Key aspect of this approach is the development of an evaluation method appropriate for environmental protection measures, which links the various impact indicators recognised in the impact assessments and allows their integrated assessment.

Jan 1, 2005

To simplify programming, image analyzers commonly measure either linear intercepts or the areas of particles and grains to determine liberation based on polished section mounts. However, the concentration of minerals by flotation is based on reagents that interact with the exposed surfaces of the minerals. Thus, it is often perceived that image analyzers should measure the perimeter of the mineral of interest in the ore particles. A comparative liberation study of thirteen samples collected from a flotation plant processing a complex base metal sulfide ore showed that the liberation of the ore minerals determined by area measurements is very similar to the liberation determined by the exposed perimeters. The liberation determined by exposed perimeters is more appropriate only for those cases where the mineral texture is so complex that it is retained in the small particles generated in conventional grinding operations.

Jan 1, 2002

By H. Wagner

INTRODUCTION One of the most important tasks facing the opera¬tors of deep-level gold mines is supporting the roof strata in the immediate vicinity of the stope faces. Some of the deeper gold mines operate at depths ex¬ceeding 3.0 km; the extreme mining depths and the tabular nature of the gold-bearing reefs result in high stress concentrations at the abutments of the stope faces. These, in turn, lead to extensive fracturing of even the hardest quartzites. Although most of these fractures develop in a stable manner, there have been many instances where rock failure occurred suddenly, resulting in a considerable amount of damage to the underground workings. Such violent rock failures commonly are known as "rock bursts," and they are typical of many hard-rock mines that are operating at great depths. To safeguard mining personnel and equipment against the effects of stable and unstable rock failures, adequate support must be provided to the fractured roof as quickly and as effec¬tively as possible. Traditionally, timber props and timber packs have been utilized to provide roof support in gold mine stopes up to 1.5 m wide. Both methods of support suffer from the fundamental disadvantage of generating sup¬port only in reaction to movement of the strata. Since unrestrained strata movement often results in a break¬down of the frictional forces that preserve the stability of the intensely fractured roof strata, it is essential that stope supports have rapid load-bearing characteristics. An equally important requirement is that the roof sup¬ports be able to accommodate displacements of the rock mass. A third requirement of roof supports in gold mine stopes is that they must be able to accommodate the high rates of stope convergence typical of rock bursts. The hydraulic prop is the obvious choice for sup¬porting the stope faces in deep-level hard-rock mines. Since hydraulic props can be installed with a positive setting load, they can provide roof support that is independent of strata movement. By equipping the hydraulic props with yield valves, they meet the require¬ment of being able to accommodate rock-mass displace¬ments. However, the requirement of being able to accommodate high rates of stope convergence without overloading or damaging the rock strata was rather difficult to meet. The first introduction of hydraulic roof supports into gold mine stopes showed that conventional hy¬draulic props, such as those used in coal mines, were completely unsuitable for a number of reasons, in¬cluding: 1) Since drilling and blasting are used to break the ore in gold mine stopes, supports installed close enough to be effective are exposed to the vigor of the blast. Conventional coal-mining props suffered extensive blast damage, despite being protected by a blast barricade. 2) The environmental conditions in gold mine stopes favor corrosion. The high quartz content and the abrasiveness of the ore further aggravate the problem by damaging the protective coatings on the hydraulic surfaces. Simply changing the design of gold mine props to have the piston project from the bottom rather than from the top resulted in dramatic improvements in the service life of the props. The improvement was attributable to external water in the stope washing the fine quartz grit away from the hydraulic surfaces, rather than concentrating the particles between the cylinder and piston of the prop. 3) The most obvious deficiency of conventional coal mining props was their inability to yield rapidly enough to accommodate the high convergence rates of rock bursts without overloading the supports. As a result of the first disappointing results with hydraulic supports in narrow hard-rock stopes mined by drilling and blasting, a comprehensive research and development program was undertaken. The hydraulic props resulting from several years of research and exten¬sive field trials are described herein. To date (1978), more than 130,000 of these props have been manufac¬tured and used successfully in a number of mines and under a variety of geological conditions. Although many of the detailed specifications are directed spe¬cifically to gold mining conditions, there are a number of points that are of general importance in the design of underground support systems for tabular excavations in hard-rock mines of any type. SPECIFICATIONS FOR RAPID-YIELDING PROPS Yield Requirements The yield requirements for hydraulic props in deep¬level hard-rock gold mines are summarized in the fol¬lowing paragraphs. Slow Yield Load: The design of the yield valve must allow the yield load to be preset to between 300 and 400 kN. This flexibility is necessary to account for the differences in the strength properties of the roof and floor strata. Drop in Load Under Slow Yield: The drop in sup¬port load during a slow yield should be as small as possible, but it should not exceed 5% of the slow-yield load. Rapid-Yield Load: The load exerted by the prop during periods of rapid stope convergence should be as close as possible to the slow-yield load. The rapid-yield load should not exceed the slow-yield load by more than 15% at yield rates of 1.0 m/s. The limitation of the upper valve of the yield load is important; it deter¬mines the hydraulic performance of the yield valve. The hydraulic props that satisfy this criterion have performed well, even under severe rock bursts. Load Changes Under Rapid Load: On some of the earlier rapid-yielding props, conditions of dynamic in¬stability were observed; these conditions resulted in a complete breakdown of support resistance. It is essen¬tial that the force oscillations during rapid yielding be as small as possible, not exceeding -*5% of the average rapid-yield load at a yield rate of 1.0 m/s. Longitudinal Resilience: During rock bursts, vibra¬tions of the roof and floor sometimes are observed. To

Jan 1, 1982

The Ernest Henry copper-gold project is located in North West Queensland, Australia and commenced production in late August 1997. Utilizing a philosophy of selecting the biggest proven equipment available Ernest Henry at full production ¥ill treat 9 Mtpa through a single grinding line over a 15 year mine life. 350.000 tonnes of concentrate a year will be produced, containing 95,000 tonnes of copper and 120,000 ounces of gold. The two mills recently commissioned at the Ernest Henry Copper/Gold Mine are a 10.4m x 5.1m (34 ft x 16.75 ft) SAG Mill and a 6.1m x 8.4m (20 ft x 27.5 ft) ball mill. The mills have a power draw of 11 MW (14745 hp) and 5.5 MW (7373 hp) respectively. While the SAG Mill is not the largest SAG Mill in the world, it is the largest shell-supported SAG Mill in the world. The Ernest Henry mills epitomize the new standard design of large grinding mills. The design was introduced more than 20 years ago and has been further developed from extensive experience with grinding mills, and the need to produce a design, which overcomes the recognized problems of large mills. The result is a design with the potential to be used for mills up to the largest for which machine tools can be found to fabricate and machine them, currently approximately 15m (48') overall diameter.

Jan 1, 1999

By Martin Herrenknecht

Tunnel boring machines continue to develop to take on not only larger and larger diameters but also more difficult ground conditions. Ground conditions consisting of unstable faces with water pressures up to 15 bar has required innovative design approaches. A systems approach has been required to produce tunnelling machines that can not only safely excavate the tunnel but do so in an efficient, cost effective manner that stresses production and labor saving approaches. This paper will review the current design developments and present recent projects where these most recent principles have been applied.

Jan 1, 2008

Geopolymerization is a process by which Al-Si minerals undergo dissolution and polymerization in an alkaline solution to form a monolithic material with a high mechanical strength (Davidovits, 1991; 1994). In this study, Na-feldspar (albite) and K-feldspar (microcline) have been selected to investigate their abilities to undergo geopolymerization. The interaction between alkali metals present in the alkali-feldspars and alkali metal cations contained in alkaline solution during geopolymerization has also been studied. It has been found that both albite and microcline can be applied in geopolymerization to produce geopolymers with a high compressive strength. Although the dissolution of M-feldspar (where M = Na and/or K) in concentrated MOH solution is inhibited when the alkali metal cations of the alkaline solution differ from the alkali metals structured in M-feldspar, the resulting geopolymers are found to demonstrate a higher compressive strength. Moreover, a proper molar ratio of Si/Al in the geopolymeric gel phase and a higher average hardness of the undissolved particles remaining in the geopolymers are found to greatly increase the ultimate compressive strength of the geopolymers.

Jan 1, 2002

By F. N. Kissell, C. D. Litton

This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

Jan 1, 1993

Nuclear power currently produces about 20% of the electricity in the US, with 104 nuclear power plants located in 31 states. The commercial US nuclear industry contributes over $4 billion annually to US workers in salaries and wages. 25,000 new jobs need to be filled in the next 5 years. There are over 30 new power plants under consideration by US utilities. The operating reactors use uranium oxide fuel enriched to about 4% U235 and fission is the process used to generate heat to form steam to drive the turbine generators. Nuclear energy is an important element in the US generation portfolio and represents the largest producer of nearly emission-free electricity. Most, if not all, of the operating plants will secure an extended 20 years of operation or more. The last plant constructed was ordered in 1978. New smaller, modular reactors are under design to provide less expensive, expandable generation options.

Jan 1, 2011

By Claudio Flores Martinez

The prospect of accomplishing economically and scientifically profitable deep-sea mineral mining within this decade or the next one is of particular interest to the emerging discipline of astrobiology which is concerned with the origin, distribution and future of life in the Universe. Several planetary bodies within our own Solar System such as Jupiter’s moon Europa and Saturn’s Enceladus now appear to be potentially habitable, or life-friendly, in terms of the three prerequisites for life as we know it: a sustained body of liquid water, biogenic elements (C, H, N, O, P, S) and energy sources to fuel metabolic reactions. Europa, for instance, possesses a global subsurface ocean, believed to be up to 100 km in depth, hidden beneath a kilometer-wide ice-sheet. A silicate mantle is directly interacting with a cold, aphotic ocean in which tidal forces might drive geological seafloor activity that results in the creation of hydrothermal systems. These locales are commonly hypothesized to be the cradles for an alternate origin of life on Europa. Especially alkaline hydrothermal springs, as found at Lost City, have been at the center of modeling the prebiological evolutionary dynamics preceding cellular life. Serpentinization-like reactions are also possibly fueling metabolic networks in putative microbial communities found in the oceans of the icy moos. Major space agencies around the globe are planning future space missions aimed at exploring and eventually characterizing potential life forms in these habitats. The technology needed for this exploration effort resembles the requirements for a successful deep-sea mineral mining industry: highly efficient AUVs (also equipped with biologically-oriented instrumentation), swarm robotics, landers, seafloor rovers and general high-pressure, cold temperature extreme environment engineering. Interestingly, science questions of deep-sea mineral mining and astrobiology converge too: the hypothesis of life originating at hydrothermal systems, the biogeographical distribution of species among these environments, adaptations of extremophilic organisms across the three domains of life and adequate autonomous robotic systems to assess the complexity of deep-sea biological communities. This presentation attempts to present a two-fold view of advanced planetary exploration that relates to a sustainable vision of deep-sea mineral mining: charting our oceans and developing technologies least harmful to endemic biology can propel the design and prototyping of future robotic planetary probes bound for aquatic missions on alien moons. Space industry, government and public interest towards a broadened planetary perspective on deep-sea mineral mining is promoted by addressing an astrobiological rationale of this endeavor.

Sep 1, 2014

By Farrukh M. Mazhar, Philippe P. Martin

Electrical Vertical Sounding (EVS) profiling has proven to be a valuable tool to set the alignment and guide the design of a 17 km-long, 4.7m diameter water-conveyance tunnel in the Peruvian Andes at an altitude of 4,260 m. EVS profiling helped determine where to locate boreholes, and reduce the amount of drilling to 1,200 m of vertical and inclined boreholes. EVS profiling allowed the designer to identify and verify by drilling the existence of zones with difficult tunneling conditions that were avoided by realigning the tunnel. The rock quality was checked by drilling and a combined scheme of excavation by TBM and conventional drill and blast technique was developed for the final design.

Jan 1, 2003

By G. Luttrell, S. Keles, M. Eraydin, R. Yoon

The dewatering of fine particles is energy intensive and often requires costly capital expenditures. To address these issues, a series of advanced dewatering technologies have been developed at Virginia Tech. These include novel dewatering aids that enhance the performance of existing filtration equipment and an innovative hyperbaric centrifuge that utilizes both air pressure and centrifugal force for dewatering. The moistures obtained using these processes are 30-50% lower than those obtained using conventional methods. Another dewatering technology, known as the hydrophobic displacement process, can reduce product moistures to a level previously attainable only through the use of thermal dryers. This article presents test results obtained with these various advanced dewatering technologies along with estimates of the power consumption for each process.

Jan 1, 2007

By R. A. Hodge

Over the past decade, there has been a significant increase in effort put to tracking progress toward sustainability. Many aspects of society are participating in this “movement” including mining. The drivers are diverse and include evolving ideas in business and public administration as well as concerns for human well-being, community robustness, environmental integrity, and overall social and ethical responsibility. The scale in question varies greatly from local to global. For the most part, there has been a pre-occupation with developing discrete measurable signals. This paper argues that the overwhelming focus on the quantitative is ill-advised and that a more effective approach is to bring together the best of both quantitative and qualitative. The mining industry in particular is well-placed to affect this shift and reap the associated benefits.

Jan 1, 2004

By Jozef F. Zurawski

Increasingly new interceptors or new Combined Sewer Overflow (CSO) projects require connections to existing tunnels. More often than not, the existing facilities are old, in poor or questionable conditions, without proper construction records or as-built drawings. Many cannot be easily inspected unless major construction effort provides flow by-pass for safe access. This paper provides general guidelines on how to approach the problem of assessing the condition of old tunnels, how to plan and design the connection with limited physical assessment, how to develop the scope of work for the bid documents and how to provide geotechnical guidelines and designs for the bid documents.

Jan 1, 2008

By H. H. Murray

Recently developed clay deposits that will impact regional and world markets are described. These deposits, their location, geology, and physical properties are delineated. Kaolins from the State of Para in Brazil and from Ukraine; bentonites from Argentina and India; and palygorskite and sepiolite from China are world class deposits that when processed using modem technology will produce excellent products. Other deposits that may affect regional markets are kaolins from China, Australia and Indonesia; bentonites from Georgia (formerly USSR) and China; and palygorskite from India and Ukraine. New ball clay deposits that will affect regional markets are in China and Indonesia.

Jan 1, 1999

By G. P. Tomaino

Talc is a layered, hydrous magnesium silicate mineral. It has a soft, soapy feel and typically a smooth texture. Talc is also known for its insulation, heat resistance, chemical stability, oil absorption and strong covering quality. Talc, Mg3Si4O10 (OH)2, has a theoretical chemical composition of MgO at 31.7 percent, SiO2 at 63.5 percent, and H2O at 4.8 percent. However, talc’s chemical and mineralogical composition can vary depending on its geological history/parent rock association. These mineral associations and variable levels are usually chlorite and carbonates (magnesite, calcite and dolomite). Two key elemental substitutions that can occur in the talc crystal structure are iron for magnesium and fluorine for hydroxyl. These compositional differences may limit or enhance the talc’s usage in specific market niches. The United States remains self-sufficient in most grades of talc.

Jan 1, 2005

By Michael Gilbert

In the world of tunneling the glamour is in the large diameter, long tunnels, but perhaps the number of projects for small diameter and short length tunnels are greater and generally have higher risk factors. Reasons for these higher risks include both the ?boiler plate? contract provisions used on these types of contracts, the technical specifications related to the tunnel work (versus the pipeline construction), the bid practices including measurement and payment and the construction. This paper reviews and comments on some of the key issues the authors have observed in recent major pipe-line projects that involve a small percentage of tunneling footage of the total contract.