Search Documents

By A. A. Compoli

Injecting water under pressure to wet the coalbed in advance of mining reduces mining-generated respirable dust. Owing to economic and geological barriers, water infusion for longwall dust control in the United States is currently limited to the Pocahontas No.3 Coalbed in Virginia. Water is pumped into the coalbed through underground boreholes drilled horizontally from the headgate toward the tailgate side of retreat longwall panels. This paper theorizes that the barriers to widespread utilization of water infusion for longwall dust control could be overcome by long-duration, low-pressure water infusion through vertical gob gas boreholes. Currently, 43% of the 72longwall mines in the United States employ vertical gob gas boreholes. Computer coalbed reservoir simulation suggests that one vertical surface borehole could infuse the same longwall panel area as four horizontal boreholes in the current water infusion system for longwall dust control in the Pocahontas No.3 Coalbed.

Jan 1, 1995

By Ingemar Marklund

INTRODUCTION Today at LKAB, the primary mining method used is sublevel caving, independent of ore-body size, shape, dip, and geographical location. The mining of small ore bodies with relatively flat dip involves a lot of develop¬ment work, a large initial investment, big dilution, and large ore losses. In 1975 serious investigations into other possible methods, especially for those small ore bodies which do not lie in direct contact with other ore bodies, began. Different methods were studied and a number of in¬teresting ideas came from Russian mines. An analysis was made of one of the proposed methods, sublevel benching, in which mining is carried out from raises, and which uses the throw from the blast to place the broken ore. However, there were reservations about working in big open rooms at great depth, and doubts about the possibility of getting acceptable drilling results in an acceptable environment from raised platforms. Testing was therefore delayed for a time. However the investigations continued and in the fall of 1976, it was decided to try vein mining in a small ore body (Indian) (see Figs. 1 and 2). MINING RESULTS The results are now available from the mining of Indian and are as follows: Ore plan area 1200 m2 Level height 50 m Ore volume 60 000 m3 Ore tonnage 270 000 t Iron content 62% Dip 0.69 rad (40°) Ore thickness 14 m Ore compressive strength 26 MPa Ore C-factor (fracture density) 0.21 Hanging wall compressive strength 28 MPa Hanging wall C-factor 0.27 About 40 000 m of the holes were drilled by ring drills with an average productivity of 85 m/shift; loading of a round (2 rows, 750 m of hole) was usually accomplished in one shift. The total ore recovery was about 270 000 t with an average iron content of 59%, and three to four shifts were required per round (4700 t) to load. The principal of "throwing" the rock during blast¬ing worked well, and no ore remains on the footwall. ROCK CONTROL Before mining commenced at Indian, it was dis¬covered that the rock strength in its vicinity was rela¬tively poor. Since the ore is flatly dipping, and mining was to take place with open rooms, the strength of the hanging wall was of great importance. A supplementary program of exploration drilling was done during the fall of 1976 in order to assess fracture spacing and rock strength from the drill cores. Results showed that the strength of the hanging wall was low because of the many fractures. A decision was made to try cable bolting of the hanging wall by extending some of the ordinary blast¬holes. Cables (20 mm diam) were grouted in these larger holes and the rest of the hole was then utilized for ordinary loading (see Fig. 2). About 100 bolts altogether were installed and, to date, only small falls have occurred and the hanging wall is holding. Its exposed area is 2100 m2 DEVELOPMENT WORK On the 350-m level, four crosscuts (two per mining room), one longitudinal drift, and two elongated drifts (one per raise) for the raise climber were developed as shown in Fig. 1. Of the 230 m of drift, 60 m were in ore and the rest in waste. For mining room A alone, a total of 115 m of drift were needed with 30 m in ore. The drift dimensions were about 4.5 X 5.5 m. In the drifting on the 300-m level, two connecting drifts were driven from one existing transport drift forward to the respective raises. The total development was 93 m, all in waste (Fig. 1). The two raises having a length of 80 m each were driven at an angle of 0.68 rad (39°) from the hori¬zontal. They were driven along the footwall contact with a separation of 30 m and had an area of 10 m2. LONG-HOLE DRILLING The drilling of long holes with the ring drilling unit began in the fall of 1977 in raise A. The equipment consisted of an Alimak raise climber, equipped with a lower platform from which the charging was done.

Jan 1, 1982

By Andrew Trusiak

Brunswick Mining, employing approximately 1600 employees, is located 40 km south of the city of Bathurst in north eastern New Brunswick. The mine has operated as two lead-zinc operations - the underground mine(No.12) and the open pit mine (No.6). The open pit orebody is presently being' mined by underground methods. It is expected that the No.12 mine will furnish the entire ore supply by the end of 1981. The flotation practice prior to 1971 has been described by Neumann and Schnarr(1) and by Erskine (2). More recently, the current flotation practice has been described by McTavish(3) and deals with some major circuit modifications between 1972 and 1978. The period 1978 to 1980 has seen the completion of. a major flotation cell replacement and expansion program for the No.6 concentrator, and the implementation of computer control in the No. 12 CuPb and Zn flotation circuits.

Jan 1, 1981

By C. Y. Chen

Public Law 75-87, the Surface :mining Control and Reclamation Act of 1977 (SMCRA), Section 516(b) requires the underground coal mining operator to "adopt measures consistent with known technology in order to prevent subsidence causing material carnage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonably foreseeable use of such surface lands, except inn those instances where the mining technology used requires planned subsidence in a predictable and controlled manner . . .?. The Congress also directed the Secretary of the Interior to promulgate regulations to implement the law. As a result, the control of subsidence from underground coal mining to minimize surface damage has become the mandate of a Federal law. This paper discusses the mechanics of subsidence and the effects of subsidence on ground features and also summarizes some of the measures which have been used to minimize the possibility of damage to surface structures as a result of subsidence due to underground coal mining.

Jan 1, 1981

By Eung Ha Cho, Olufemi Olajide

A laboratory study of dense-medium cycloning with Redstone seam coal has been conducted. The investigation was performed using a 203 mm (8 inch) Heyl-Patterson dense-medium cyclone. Two underflow orifices of 31.8 mm (1.25 inch) and 44.5 mm (1.75 inch) in diam were used. The effects of feed pressure and particle size were determined on the cycloning performance. In addition, the cyclone performances with coal-rich and refuse-rich samples were also investigated. The results of the experiments were analyzed using basic hydrodynamic principles. The increase in the feed pressure increases the specific gravity of separation (defined as the specific gravity of a particle which has an equal chance of reporting to either the overflow or underfow) for both underfow orifices. The specific gravity of separation increases as the particle size decreases with the smaller underflow orifice. However, an opposite relationship has been observed with the larger under flow orifice. The separation becomes sharper with the smaller under flow orifice than with the larger underflow orifice especially for fine material. Also, the separation becomes sharper with an increased feed pressure for a coal-rich sample. However, this effect is less significant for a refuse-rich sample. This means that a high feed pressure is required for a coal-rich sample to maintain a good separation. It also means that applying a high feed pressure provides a good separation regardless of the type of feed coal in terms of ash content in the solid.

Jan 1, 1990

By J. Astier

The idea of using only one strand for both sintering and cooling of the sinter is not new. In 1952, in the U.S.A. a sintering plant was built at Benson Mine (Star Lake, N.Y.), including : - 68 m2 or 735 sqft (8 wind boxes) for sintering, - 22 m2 or 237 sqft (3 wind boxes) for cooling. In the USSR, a large number of machines have been built allowing for cooling of the sinter on the strand, especially the 4 m (about 13 ft) machines, with : 252 m2 sintering grate area 60 m2 cooling grate area 312 m2 total grate area. However, such ventures did not prove very successful, and the IRSID embarked many years ago on a research program to discover : - what are the problems associated with cooling on a sintering strand ; - what are the possible solutions for industrial plants.

Jan 1, 1974

By Richard Jr. Ray, David Johnston, Phil Blankenship

Injection of inert gases to combat mine fires has been practiced in various parts of the world for a long time. Of late, nitrogen has become the preferred inert gas for control of mine fires and safe salvage of longwall equipment as compared to carbon dioxide or fuel gases produced from burning of fuel. In India, carbon dioxide has been used for fire fighting in a number of mines during the 1960s and 1970s. More recently inert gas produced from burning of fuel oil in surface plants has been used in controlling the atmosphere in fire areas in two mines. In yet other cases, liquid nitrogen has either been poured directly into fire areas in liquid form or injected in gaseous form to keep the fire in check. Nitrogen produced in liquid form in an oxygen plant is more costly than nitrogen produced from PSA (pressure swing adsorption) based plants. A PSA-based plant has been installed in one of the Indian mines in 1986 and more are in the offing. This paper reviews the application of various inert gases in Indian mines and discusses the likely trend of inert gas application in Indian mines in the future.

Jan 1, 1989

By Shular R. Scudamore

There was a time when heavy-duty apron feeders were built to last almost forever. The machines were heavy and built to maintain certain expected longevity and reliability. Increasing emphasis on return on capital leads to cost-effective designs. Costs can be increased or decreased, depending on customer specifications and the design philosophy of the feeder manufacturer. Specifiers can make important contributions to cost effectiveness. To do so, this article describes what should be known about planning with a supplier for heavy-duty apron feeders. There are several factors that should be considered, including capacity, characteristics of material carried, length, method of feeder loading, degree of lift, hopper opening, pan construction, and type of drive. Today's apron feeders are built in various sizes and with a variety of components to handle heavy, lumpy, or abrasive materials that can ruin lighter feeders. Careful feeder selection is important if it is to provide a controlled feed rate, absorb huge impacts, be used with long hopper openings, and have a relatively low power-perton capacity. Variations in systems and materials demand that each feeder be designed for its application, drawing on a wide range of components. Therefore, certain factors must be considered before final specifications are drawn. Capacity The design and application of an apron feeder is based on how material passes through a given system over the feeder into processing machinery. The processing machinery's capacity governs other equipment and productivity of the flow. From this basic information, related sizes of upstream equipment can be determined. Of these, the apron feeder acts as the "mouth and neck of the bottle." No more will pass than the mouth and neck will accommodate. Everything in the apron feeder design, from dimensions to power, is based on processing machinery. Material Considerations Are Vital Just as the nature of materials to be crushed or screened affects capacity and productivity of a crusher or a grinding mill, so does it affect capacity and performance of a feeder. Lump size must be identified closely so the pan width can be selected to accommodate the maximum lump with room to spare. For example, a lump size of 760 mm (30 in.) indicates a pan width of 1.5 m (60 in.) While two times the maximum lump is considered minimum width, if the maximum lump

Jan 12, 1983

By J. D. Bliss

The discovery that triggered the current gold rush in southeastern Peru was made in about 1975 along the Rio Madre de Dios in Madre de Dios Department (Fig. 1). About 5000 to 10,000 miners (called chichiqueros) were working in the area as of 1990. Placer mining is the principal source of revenue for people living along the Rio Inambari and west of Puerto Maldonado. As in past gold rushes, working and living condition are harsh. Supplies are expensive, and the area has poor access compared with other areas in Peru. Food, fuel and all mining supplies are trucked over dirt roads from Cuzco, a three-to-five-day trip (Fig. 1). Some material also comes from Brazil. Many placers have a similar life cycle, beginning with small-volume mining (surface or underground). At the end of this small-scale mining, the placer is exhausted or it has a sufficient volume of gravel high enough in gold grade to be worked by large-volume methods, which lead to exhaustion of the resource. The level of maturity of a placer can be determined from its gold grade. The amount of gold production from large-volume mining can be predicted, given detailed, cumulative gold-production data on placer deposits during small-scale mining (Bliss et al., 1987). Using this general model, the authors analyzed the placers in the Rio Madre de Dios area. Small-volume mining Most placer mining in the Rio Madre de Dios area is in alluvial deposits either in or bordering the major rivers. Locally, some placer mining is in terrace deposits above the rivers. All minerals (including the subsoil) in Peru belong to the state. However, a mining claim (denuncia) is easily obtained for mineral exploitation. It is separate from property ownership.

Jan 1, 1992

By Ramon B. Santos

The Atlas Concentrator, reputedly the largest in the Far East today, is located on the island of Cebu in the Republic of the Philippines. It started operation on a 4000 TPD capacity in 1955. An expansion program, coupled with significant improvements both in the Crushing Plant and the Mil, made the Atlas Concentrator what it is today, treating about 14,000 tons of ore per day at a comparatively low cost of about $0.50 per ton treated. The Atlas Copper Mine is at present mainly an open pit operation, with ore supplied from two pits (Lutopan and Biga) north of the Concen¬trator. Development of an Underground Mine, situated on the main ore body at Lutopan, which will be a block caving operation, has been underway since 1963, and this underground mining operation is expected to b e in full production by the latter part of 1966.

Jan 1, 1966

By K. N. Han, N. S. Kim, H. Yoon, J. S. Sohn

The leaching behavior of silver and silver oxides in ammonical solutions has been studied. The current study is concerned with an effective recovery of silver from secondary sources such as spent silver batteries. Silver associated with these batteries appears in various forms including metallic silver, argentous oxide, Ag2O and argentic oxide, AgO. The leaching behavior of metallic silver in ammoniacal solution has been studied using an electrochemical mehtod. Oxidants used in this study include hyperchlorite, hydrogen peroxide, bromine and iodine. Results on cyclic polarization and Tafel plots on the silver anode in ammoniacal solutions are presented and the results are discussed. The dissolution rate of metallic silver in ammoniacal solutions is also compared with those of silver oxides.

Jan 1, 2002

By B. Kolonja

This paper considers simulation of truck dispatching system designs using maximum expected production of the truck-shovel system as the measure of performance. Two methods are utilized, multiple comparisons with the best (MCB) and the combination of MCB and the variance reduction technique known as common random numbers (CRN). These two techniques are compared via simulation experiments. The results show that the combined procedure of MCB with CRN is the superior tool to reduce the total number of replications needed to ensure the specified probability of correct selection over the finite number of designing systems. In this case study, MCB with CRN reduces the variance by 29% and the number of required replications by 48%. Also, the MCB with CRN procedure narrowed the confidence interval by 18%.

Jan 1, 1994

By T. S. Bomar, C. J. Wood

Heavy media cyclones (HMCs) are efficient, high-tonnage devices suitable for upgrading run-of-mine coal in the 50 to 0.5 mm size range. Unfortunately, industrial HMC circuits are often not optimized due to problems such as incorrect operating pressures, poor feed distribution, excessive media contamination, mismatched components, and improper density control. To avoid these problems, operating guidelines have been provided in this article that are useful for optimizing the performance of HMC circuits. The validity of these guidelines has been assessed by means of density tracer tests carried out at several coal preparation plants.

Jan 1, 2002

By Yoneji Kanoh, Masahiko Ohtsuka

In Japanese tunneling history, it has commonly been accepted that the long-round driving is difficult due to the complicated geological condition. Therefore, the maximum past record has been less than 3 m per round. A new record of advance was established in the 99 m2 headrace tunnel of Imaichi Water Power Station Project with an advance of 239.5 m in a month by drilling 3.9 m deep blast holes. The geology of the headrace tunnel composed of pyroxine andesite (ie. 960-1770 kg/cm2, VP3.1-4.3 km/s) which had several clay seams and open cracks and was moderately weathered. Automatic shotcrete machine was used for shotcreting. Rock support was specified according to the N.A.T.M. with each different rock type. The contractor achieved a remarkable tunneling advance not earlier experienced in Japan.

Jan 1, 1983

The Australian states of New South Wales (NSW) and Queensland, because of their endowment of black coal resources, dominate the production and export statistics for Australian coal. NSW produced 86 million tonnes of saleable coal in 1994, representing a doubling of output since 1980, or a growth of 5% per annum. Asian demand for thermal and coking coal has, of course, driven this growth in NSW. This high Asian demand is forecast to continue and NSW will seek to secure its share. This paper focuses on some of the issues facing NSW in the future, and in particular, examines some of the major new and proposed mining projects.

Jan 1, 1997

By S. Hamilton

Occurrences of boron-containing ores are relatively rare on a global basis. The first verifiable use of borax was in the 8th century by Arabian gold and silversmiths. Due to the rarity of the borate mineral occurrences, borates were originally traded at relatively high prices and were used for very specialized applications. Today, there are

Jan 1, 2006

A charge of the Research Council of the Society for Mining, Metallurgy and Exploration, Inc. (SME) is to ?? identify longer term research ideas/needs, that in the perception of the SME Research Council, could represent significant technology breakthroughs ?? (SME, n.d.). In 2008, the Council decided that instead of unilaterally developing a list of top priorities, it would involve the entire membership of SME in identifying the top priorities. Additionally, it decided to keep the list short. This paper describes the process and results from that exercise.

Jan 1, 2010

By J. R. Patts, L. D. Patts, S. J. Janisko, T. Barone

"Controlling float coal dust in underground coal mines before dispersal into the general airstream can reduce the risk of mine explosions while potentially achieving a more efficient and effective use of rock dust. A prototype, flooded-bed scrubber was evaluated for float coal dust control in the return of a continuous miner section. The scrubber was installed in line between the ventilation tubing and an exhausting auxiliary fan. Airborne and deposited dust mass measurements were collected over a period of three days at set distances from the fan exhaust to assess the changes in float coal dust levels in the return due to the operation of the scrubber. Mass-based measurements were collected on a per-cut basis and were normalized per foot of advance by the continuous miner. Results show that average float coal dust levels measured under baseline conditions were reduced by over 91% when operating the scrubber. INTRODUCTION In 2012, underground mining in the United States produced over 342 million tons of coal [EIA 2013]. During the cutting, crushing, and transport of this coal, dust is generated and can be entrained in the air ventilating the mine. Title 30 Code of Federal Regulations Part 75.400-1 (30 CFR§ 75.400-1) defines float coal dust as particles of coal that can pass a No. 200 sieve. These coal particles can be carried by the ventilating air into return entries before settling onto mine surfaces [NIOSH 2006]. If this float coal dust becomes re-entrained into the airstream, it can propagate an explosion throughout mine workings [Harris et al. 2010]. Application of rock dust in underground coal mines is required by Federal regulation as a means of preventing the propagation of explosions by float coal dust. In order to meet Title 30 Code of Federal Regulations Part 75.403 (30 CFR § 75.403), 80% incombustible content must be maintained in the composition of dust deposited in mine entries [76 Fed. Reg. 35968 (2011)]. This fraction of incombustible content is increased if elevated levels of methane are present. In order to maintain the required incombustible content, frequent or constant application of rock dust is undertaken by mine operators. Title 30 Code of Federal Regulations Part 75.2 (30 CFR § 75.2) defines the properties of the rock dust that must be used by mine operators."

Jan 1, 2015

By Andrew I. Hustrulid

The Internet and World Wide Web create multiple opportunities to advance and change an industry. Scandura Conveyor Belting, a mid-sized manufacturing company supplying the mining industry, has embraced several of these opportunities that add value to the sale and service of the manufactured product. This paper presents a technical overview of available technology and how it is being applied to advance the conveyor belt industry. These technologies are used to provide historic catalog information, interactive troubleshooting, product installation and service instructions, detailed product information, technical calculations for the proper conveyor belt selection, and on-line site surveys and maintenance logs.

Jan 1, 2002

By R. S. Rickard, B. Ball

INTRODUCTION Pyrite responds to the flotation reagents normally used in sulfide flotation systems. For example, it is well known that xanthates are good collectors for pyrite, and cyanide, sulfide and hydroxides are depressants. The particular response of pyrite to these and other reagents is used to advantage in several areas. By careful control of depressant and collector additions, pyrite can be separated from other sulfides by flotation. This is of obvious importance in base metal sulfide flotation where pyrite depression is often required to produce a marketable grade concentrate. Flotation of pyrite has long been employed in gold ore processing, and it appears that pyrite flotation from coal may become important in the future (1). It is probably a direct consequence of this relative ease of separation, plus the low economic value of pyrite, that detailed investigations on the chemistry of its flotation and depression are relatively limited. Gaudin (2,3,4) and others, in the mid-1950's published data on the flotation of pyrite, but detailed or consistent mechanisms were lacking. In 1955, Sutherland and Wark's book (5) was published, in which a large amount of empirical information, especially earlier work of Wark and Cox, was presented. More recently, in 1968, significant contributions have been made by Fuerstenau et al. (6,7) and Majima and Takeda (El. These papers introduced electrochemical explanations of the effects observed with xanthate and cyanide ions.

Jan 1, 1976