Search Documents

By Charlie Sons

Pit and underground mine operators typically use a lot of big equipment tires. Just as typically, they spend a lot of money they shouldn't on these tires. That's because tire use and maintenance are not given enough attention. That often occurs because mine management and personnel do not know the basic facts of tire use and care. If a piece of large equipment is damaged or ruined, a good explanation better he forthcoming. A ruined tire is often just a shoulder shrug. But that sort of fatalistic acceptance can cost tens or hundreds of thousands of dollars a year extra for big equipment tires. That does not have to be. There are some basic tire considerations that, if followed, will extend tire life and lower tire costs. Most companies have the inevitable conflict between the production department, which resists any restrictions that may reduce productivity, and the maintenance department. Production success is based on meeting a schedule of yards moved, while maintenance success is based on availability and equipment cost. When production falls behind schedule and equipment speeds are increased, maintenance may soon find its tire costs rapidly increasing, unless everyone understands the tires' vulnerability to damage. Unless the production department understands the problem, or restraint is applied by top management, costs may become exorbitant. At one job site, tire costs alone exceeded $250,000, to move 55 dam3 (72 000 yd3) of dirt on an 11-km cycle. The operation temporarily caught up with its schedule, but tire costs and attendant downtime soon made this a not-for-profit exercise. Because an operator must always attempt to move payload at the lowest cost, there are cases when higher than normal tire costs must be accepted. For example, in pioneering work with tandem engine scrapers, steep grades shorten tire life to less than normal. But the steep grades make shorter haul cycles possible, yielding more trips per hour than alternative earth-moving methods.

Jan 1, 1982

By Richard H. Olson

The following discussion will deal with the domestic talc industry only, inasmuch as the writer has had no experience in this field outside of the U. S. This is strictly a geological-mining approach; no attempt is made to assess in depth the effects which milling technology and marketing capability might have in determining the potential of any given talc deposit.

Jan 1, 1970

By A. Chieregati

"A heterogeneity study was conducted at Erdenet Copper Mine in Erdenet, Mongolia, to determine the fundamental sampling error associated with blasthole sampling. Using a custom designed sector sampler, six large blasthole samples were collected to perform the test that was developed by Pierre Gy, to estimate the constitutional heterogeneity factor for several types of ore. The study investigated the entire sampling protocol, from mine site to analytical laboratory, and quantified the contributions to fundamental sampling error (FSE) of the various stages of sampling and sample preparation. The total relative standard deviation (RSD) of sampling error was determined to be ±32% and ±49.4% for copper and molybdenum respectively. A classical statistics analysis conducted on the data confirmed the level of RSD. About 95% of the sampling error was produced from only one step in the sampling protocol: when the 1 kg sample was reduced to 50 g sample for chemical analysis. Therefore, it is recommended that the 1 kg sample be reduced to 50g using a slightly different protocol to minimize the FSE. The 1 kg sample should be first crushed to 0.2cm size. A 250g split should then be taken and fine ground. A 50g split should then be taken from the 250g fine ground split. These two simple steps will reduce the FSE to ±7.9% and ±17% for copper and molybdenum respectively. The modified sampling protocol effectively reduces the probability of misclassification of low grade ore to zero. INTRODUCTION The Erdenet copper-molybdenum open pit mine is located in Erdenet, in Orkhon province, Mongolia. The Erdenetiin-Ovoo copper-molybdenum deposit is between 1.5 and 3 km wide, and about 25 km in length (Erdenet Mining Corporation, 2016). Chalcopyrite, bornite covellite and chalcocite are among the major minerals found in the deposit. The mine processes approximately 26 million tons of ore annually. A study was conducted to evaluate the fundamental error associated with the blasthole cuttings and sampling protocol at the mine. The open pit mine uses 215mm diameter Russian drills to drill 17.5m holes for 15m benches. The total weight of blasthole cuttings for a 215mm diameter hole and 15m bench height is between 1.5 and 2 tonnes. This amount of sample is difficult and time consuming to collect and analyze. Therefore, a sector sampler was designed for the Russian drills to collect large samples that were representative of the blasthole cuttings (Ganguli et al., 2016). In order to eliminate the delimitation and the extraction errors, researchers consider sector samplers to be ideal for sampling blastholes (Pitard, 2008; Chieregati and Pitard, 2009). This method was intentionally more rigorous than the blasthole sampling protocol at the mine to ensure that the blasthole cuttings were properly sampled. This study was part of a broader study that also looked at the relationship between particle size and grade. The samples collected by the custom designed sector sampler were very large (195 kg on average), and therefore, sufficient for both studies. The relationship between particle size and grade has been reported in Ganguli et al. (2016)."

Jan 1, 2017

By Greg Border

Many unique ventilation problems have been faced as Avery Island Mine's large openings have been mined. High humidity of outside air combines with the hygroscopic salt to create a corrosive atmosphere. Massive rooms preclude routine use of brattices to direct air flow to the working faces. Large amounts of explosives are consumed in single blasts. Resulting concussion pounds air control structures and ANFO ignition creates large amounts of nitrogen dioxide in single rooms. Geologic constraints confine new shafts and slopes to areas thought to be free of potential ground water hazards. Dust control techniques are limited by dry product demanded by customers. The Avery Island Mine's ventilation system has evolved to deal practically with the conditions and to dependably provide fresh air to the miners. International Salt Company's Avery Island Salt Mine, a multiple level room and pillar operation, has been mined steadily since about 1900. It is known as one of the "Five Island" salt dome mines of South Louisiana's Gulf Coast. Production from the area places Louisiana first in United States rock salt mined tonnage, according to the United States Bureau of Nines, 1982 (1). International Salt Company is a major force in U.S. salt production, as it also operates mines in Detroit, Michigan; Cleveland, Ohio; and Retsof, New York; a solar salt facility in Bonaire, Netherlands Antilles; and a solution mining plant at Watkins Glen, New York.

Jan 1, 1983

By Thomas E. Garnar

Zirconium and hafnium are the twin elements of the periodic table because they are always found together. They resemble each other so closely that hafnium was not discovered until 135 years after the discovery of zirconium. Zirconium was discovered by Klaproth in 1789 and isolated 35 years later by Berzelius. Because hafnium's chemical properties are so close to those of zirconium, it was not discovered until 1923 when Coster and von Hevesy detected it using X-ray spectrographic analysis. These elements occur most commonly in nature as the mineral zircon (ZrSiO,) and less commonly as baddeleyite (ZrO,). They also are found as a variety of other silicates. Zircon was identified as a component in alluvial and beach sands in 1895, but it was not produced in any quantity until 20 years later. During World War I, it was produced as a coproduct of beach sand mining for titanium minerals just south of Jacksonville Beach, FL, and was patented as a refractory. It was not until the 1930s, when Zircon Rutile, Ltd., began mining at Byron Bay on the east coast of Australia, that zircon was first used as foundry sand. Later in the 1940s, NL Industries and Humphreys Gold Corp. began production of zircon sands from fossil beaches in northeast Florida. Baddeleyite first became available as a commercial product in 1916, but never in the quantity of zircon. Zircon holds a unique position as an industrial mineral because it is used for both its physical and chemical properties and as an ore of zirconium and hafnium metals. Australia is the major zircon producer followed by the Republic of South Africa and the United States. Zircon is also produced in India, Sierra Leone, Sri Lanka, Malaysia, the former USSR, China, Thailand, and Brazil. The location of world zircon mines, baddeleyite mines, and undeveloped zircon ores are shown in [Fig. 1]. World production of zirconium mineral concentrates is shown in [Table 1].

Jan 1, 1994

By T. M. Barton

Coal mine bumps the violent failures of over-stressed coal', present a safety hazard to miners when mining is conducted in deep, bump prone coal mines. Two different longwall gate entry systems were evaluated in a Southern Appalachian coal mine located in the Pocahontas No. 3 Coalbed under approximately 610 m of overburden which included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design employed a 24.4 m square abutment pillar' while the new design employed a 36.6 by 54.9 m' abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worse case conditions increased effective bearing area 62 pct with only a 9 pct increase in gate entry system width and eliminated face bumps that wer7 experienced with the original gate entry design.

Jan 1, 1991

By P. D. Lafleur

A concerted effort to determine the quantities and effects of trace elements in the environment requires the application of a number of different analytical techniques in the same or in different laboratories. The interpretation of analytical data is often difficult because of differing results between analysts or even by the same analyst at different times. Standard Reference Materials (SRM), which are certified for their trace element content and are in a matrix similar to the one of interest, can greatly increase the accuracy of analysis and the reproducibility between laboratories. The United States National Bureau of Standards (NBS) has developed a number of SRMs applicable to the determination of trace elements in environmental materials. Two of these, SRM-1571, Orchard Leaves, and SRM-1577. Bovine Liver, are excellent for biological tissue analyses. Several new standards are of value for fossil-fuel analyses. These are: SRM-1632. Trace Elements in Coal; SM-1633, Trace Elements in Fly Ash; SM-1634, Trace Elements in Residual Fuel Oil: and SRM-1635, Trace Elements in Gasoline. In cooperation with the US Environmental Protection Agency, the NBS has recently concluded an interlaboratory comparison involving analyses by more than 60 laboratories on these fossil-fuel materials. The resulu of this intercomparison and the broad range experience with the biological materials will be presented showing both intratechnique and intertechnique variations, and the sensitivities and comparisons with the values certified by NBS.

Jan 1, 1975

By H. Polat

Relatively large amounts of such hydrocarbons as fuel oils are often needed in flotation of low rank coals. The amount of oil can be decreased considerably by using surfactants as promotors. The reagents which are good candidates as surfactants to promote hydrophobicity can also act as emulsifying and wetting agents. Since the physical and chemical variables influence various sub-processes in different ways, their influence on the performance parameters is complex. The results of laboratory tests are presented to show that the dual role of reagents can be judiciously exploited to increase both the recovery and grade of clean coal. The mode and order of reagent addition is critical in enhancing their efficacy as flotation promotors. The results demonstrate the benefits of proper conditioning of the pulp prior to flotation.

Jan 1, 1997

By William P. Shell

An important part of process control engineering is the implementation of the basic control system design through commissioning to routine operation. This is a period when basic concepts can be reviewed and improvements either implemented or recorded for application in future systems. The experience of commissioning the process control systems in the Homer City coal cleaning plant are described and discussed. The current level of operating control performance in individual sections and the overall system are also reported and discussed.

Jan 1, 1983

By Tegner C. Johnson

Just a few years ago my company was referred to as the Marion Steam Shovel Company. We still make shovels, both two and eight crawler types. The eight crawler stripping shovel appears to have been replaced by the walking dragline for overburden removal and in some cases for the mineral as well. The walking dragline appeared in the coal fields in the early 1930's. It owes its popularity today to the fact that it can cope with overburden depths in excess of 100 feet and with blasted sedimentary rock, all at an 0 & 0 cost of ± 10¢/BCY.

Jan 1, 1974

By William E. Mead

Although this paper has been entitled "Design of Embankments for Tailings Ponds and Waste Dumps," a better title might have been "Site Selection and Design Planning for Tailings Ponds and Waste Dumps," The procedures normally followed in performing the engineering calculations based upon the measured soil properties will not be detailed. Instead, we shall look at the subject in broader perspective which considers the environmental factors and the fundamental design principles. Disposal of waste materials left from the extraction and processing of mineral deposits has become, in recent years, an important engineering consideration for mine and mill operators. Land occupancy and land values almost everywhere are increasing at a rapid rate. So is the size of mine and mill waste dumps, thanks to our advancing technology in mineral beneficiation. Mining companies are being pressured to "clean up" their operations, both literally and in a safety hazard sense. Once, long ago, the miner could use any convenient location to get rid of his mine waste and mill tailings without being concerned over possible infringement on the rights and well-being of the public. Today, however, he must pay close attention to these matters if he wishes to avoid liability suits and the unfavorable reaction of civic groups as well as local and regional government. Most operators keenly sense their increased responsibility, not only because they are legally vulnerable, but because they realize the necessity for sharing space harmoniously with the rest of society.

Jan 1, 1967

By C. E. Capes

The spherical agglomeration process provides an attractive method for the cleaning and recovery of fine coals in the form of compact oil-bonded pellets. In treating a washery effluent containing 50% minus 20 micron material by this technique, the slurry was first mixed under vigorous agitation with oil to deash and dewater the fine coal. The flocculated coal pulp was then formed into larger agglomerates on a modified balling disc. The operation of a semi-pilot scale process is described and an analysis of some of the operating and system variables is given. A semi-theoretical expression to predict the final agglomerate size under various conditions is derived and compared with the experimental data. Coal producers are faced with a growing requirement to clean and recover fine mesh coals. Greater mechanization of the extractive and preparation processes has resulted in finer-sized products containing larger quantities of associated foreign matter and preparation plant effluents contain quantities of fine coals which are potentially valuable. These losses will probably increase with the expansion of production and will require the development of effective disposal and utilization processes under pressure of the lack of adequate disposal areas, the enforcement of air and stream pollution laws, and the economic need to obtain the maximum yield of salable product(1)

Jan 1, 1970

By M. Jessop, V. O. Kofoed, R. Blanchard, A. Hughes

Willowstick has successfully employed a new Seismic Acoustic Resonance (SAR) method to improve seepage characterization through, beneath, and around dams. SAR is a passive seismic method that detects zones of higher permeability in the foundation and fill materials of a dam. Just as the ocean has tides, the earth’s crust experiences daily “Earth Tides” and is constantly in motion. Continual motion produces resonance signals that can be measured, interpreted, and modeled to identify zones of higher permeability within a dam and its foundation. The SAR results are analyzed in conjunction with the traditional Willowstick Method to better characterize seepage flow paths and patterns trough, beneath, or around a dam in three dimensions. When both methodologies, which use entirely different scientific principles, identify the same anomalous feature, a higher degree of confidence is gained in the results of the investigation. Willowstick has effectively utilized the SAR method on many successful dam seepage investigations. The two geophysical techniques when used in parallel have yielded complimentary results, with both methods providing beneficial information about seepage locations. This paper will detail seepage flow paths identified using both Willowstick and SAR methods for two case study tailings dams in Canada and the United States.

Feb 1, 2023

By A. Vien

MOCCA is a Multivariable Optimal Constrained Control Algorithm developed specifically for non-square industrial control applications with practical difficulties such as interactions, time delays, constraints, modelling development, etc. MOCCA consists of an off-line simulation/translation module, for tuning the control parameters, and an on-line module that implements the designed control law. This paper describes an evaluation of MOCCA on the Hemlo grinding circuit which comprises one open circuit ball mill and two closed circuit ball mills in series. In this case a 4x4 unconstrained control problem was considered. The manipulated variables included the fresh ore feed rate and three pump box water additions. The controlled variables were the grinding circuit product particle size and three pump box levels. In this application soft constraints were implemented through control action and control error weighting. The feedforward capability of MOCCA was used to compensate for a measured water flow disturbance to one of the pump boxes. MOCCA performed very well during plant evaluations when compared to the original classical multi-loop control strategy and proved to be quite robust. Perhaps most importantly, the process engineers and plant operators have a high level of comfort both in understanding MOCCA's general operating principles, and with its demonstrated performance.

Jan 1, 1991

By Y. C. Kim

The results from a retrospective study are described in this gaper in which she past development drilling activities were investigated using geostatistics. The purpose of the study was to determine the amount of savings in drilling cost that could have been realized through the optimal placement of sequential drill holes using geostatistics. Out of 144 DDH's that were in place within the study area, the results showed a possible elimination of 34 DDH's without any reduction on the confidence interval of the global reserve estimates. If the incremental savings from one drilling campaign to the next were considered, however, the amount of percentage savings were even greater. Other interesting results from this study were; 1) tangible demonstration of the importance of a proper geologic delineation within the study zone, and 2) the robustness of the obtained experimental variograms from the rather early stage in development drilling.

Jan 1, 1981

By R. Maurice King

In the operation of today's large scale ore-processing mills, it is extremely important to have some way of making an objective evalu¬ation of the performance of the available flotation reagents. Attempts to do this may often result in inconclusive findings since the magnitude of the difference in the mill results for any two reagents is apt to be quite small compared to the variability introduced by the process and 'the analytical procedures used to measure them. In cases where two reagents give vastly; different mill results, evaluation becomes a simple matter and as such deserves no further attention here. A question of primary concern, however, is how a mill can go about evaluating the performance of two reagents which may, for example, give a difference of only 0.001% copper in the-tailings or of 0.2% in copper recovery. The casual observer may feel that such small differences may be of little importance, but in a mill-whose daily tonnage is between 30 and 40 thousand, these differences could mean a substantial savings. Before the presentation of an actual example of a reagent testing scheme designed for just this-purpose, perhaps a few minutes should be devoted to a review of some statistical methodology to be used later in the discussion.

Jan 1, 1964

By Walter G. Steblez

The countries of Eastern Europe are former members of the Council for Mutual Economic Assistance (CMEA). Geographically, they are located in Central Europe (Poland, Hungary, Czechoslovakia) and Southeastern Europe, largely in the Balkans (Yugoslavia*, Bulgaria, Romania and Albania*). It is important to remember that all of the countries of Eastern Europe had central planning imposed on them by the Soviet Union during the years following World War II. "Stalinist" policy for industrial development had three important tenets: • central economic planning, or a nonmarket-based command economy with administratively set prices; • economic priorities that stressed the development of heavy industries such as mining, metallurgy (steel) and heavy machine building; and • self-sufficiency at all costs, which was aimed at abolishing reliance on the world capitalist market, or reducing it to a minimum. Essentially, the system of industrialization that was used in the Soviet Union in the 1930s and 1940s was imposed on Eastern Europe. Organic market economic development in Eastern Europe ceased during this period. The flaws of this experiment became apparent when mineral processing facilities were set up in many areas of Eastern Europe that did not have reliable resources. Poland, Hungary and Romania are good examples of this situation. The Soviet Union became the principal supplier of iron ore and other minerals and mineral fuels, not only to these countries but to the Bloc as a whole.

Jan 1, 1992

By D. Gignac, P. A. Studemeister, H. Koza

Two epiclastic horizons in an Archean volcanic sequence host the gold occurrences on the Dunraine property near Wawa, Ontario, Canada. The Grace horizon of cherty and pelitic tuff strikes north-northwest and dips east. Native gold occurs with arsenopyrite in bedlike and podlike bodies of quartz lenses and stringers set in a pelitic matrix. The Parkhill horizon of lithic graywacke with associated flow-breccia strikes southwest and dips south. Native gold occurs with minor sulfides in similar bodies of quartz erratic within the Parkhill horizon. The auriferous bodies occupy paleotopographic channels and troughs within the two horizons. The former producers are the Parkhill mine with 1689 kg (54,300 oz) Au, Darwin mine with 473 kg (15,200 oz) Au, and Van Sickle mine with 48 kg (1536 oz) Au between 1902 and 1944. The gold occurrences are syndepositional with the host volcanic sediments laid during a pause in explosive volcanism. Fumaroles along steep gullies on the flank of a subaqueous volcanic center precipitated aprons of auriferous silica-sulfide mud. Downslope slumping resulted in exhalative debris flows; gold concentrated in flexures and depressions along stumpage channels. Renewed explosive volcanism covered the auriferous sediments with pyroclastic tuffs, arresting the slumping of in situ fumarolic deposits.

Jan 9, 1985

By J. Hupka

Some aspects of kerosene penetration into tar sand have been investigated. The natural tar sand porosity was measured and used to analyze the performance of the hot water process. Subsequently, pretreatment experiments, using 20 kg tar sand samples (Asphalt Ridge and Whiterocks, Utah), and kerosene as a diluent were carried out at the expected summer temperature (26°C) and the expected winter temperature (-14°C). The natural tar sand porosity accessible by diluent has a crucial impact on the reduction of bitumen viscosity, and influences the penetration time required for successful bitumen separation from tar sand by hot water processing. Thus the tar sand porosity is an important variable which determines appropriate operating conditions. Experimental results indicate that diluent penetration into the Asphalt Ridge tar sand (high porosity) is almost complete after 30 min, whereas for the Whiterocks tar sand (low porosity) the penetration process is much slower, and still not complete after 15 hours regardless of the ambient temperature.

Jan 1, 1992

By Louise H. Michaud

An interactive mine planning system that employs recent advances in 3D computer graphics capabilities and 3D geologic modelling to aid with the tasks involved in producing dragline mine plans was developed. As well as offering large potential saving in the time required to carry out the planning tasks, the system offers immediate visual feedback to the planning engineer. This can greatly aid in the conceptual understanding of complex geology and mine plans. The package incorporates the generation of a three dimensional Gridded Seam Model (GSM) as the basis for the development of the geologic database. This modelling method is capable of accurately representing rugged topography and multiple coal seams, including folding and faulting. The GSM is then integrated with an interactive graphics mine planning system in order to develop one model and one database for the generation of the mine design, the depletion of the coal resources and the movement of spoil material. The gridded structure of the model also provides the foundation on which all mine and spoil pile volumes are calculated.

Jan 1, 1992