Search Documents

By Leonidio Stegmiller

Since the petroleum crisis in 1973, charcoal1 is being considered one of the most important fuel for the Brazilian consumers, mainly for pellet's producers. In replacing fuel by charcoal mixed up with ore, obviously one of the first thing to be investigated is its influence in the product's quality. Special attention has been given to the metallurgical characteristics. This paper infocus the effect of increasing dosings of charcoal to the pellet's porosity and how other physical and metallurgical characteristics will be affected accordingly. This work was carried out using two different finesses of charcoal and dosing varied from 0.5 to 2.0%.

Jan 1, 1982

By Douglas R. Shaw

The results are discussed herein of laboratory and pilot scale research which has demonstrated some exciting prospects for the exploitation of refractory gold resources by heap leaching. The research examined practical and cost effective methods of chemical; i.e., non-biological, oxidation pretreatment of refrac­ tory old ores to enable successful conventional cyanide heap leachmg. The work has focused on regenerable chemicals, in order to minimize process consumable costs. A nitric acid method has emerged which offers rapid oxidation rates (eg, 0.5 to 6 hours) on ore samples crushed typically to% to ¾-inch. Gold recoveries in simulated heap leaching tests, after nitric acid oxidation of crushed ores, were as high as approximately 80 to over 90%, in contrast, typically, to negligible gold solu­bilities without oxidation. Nitric acid oxidation was effective when applied to several sulfide-bearing refractory gold ores which required either partial or essentially complete sulfide sul­fur conversion for high gold solubilities in cyanide. Ores rich in organic preg-robbing matter also were treated successfully, as were ores which contain significant quantities of acid-consum­ing constituents. Base metals also were recovered with nitric acid oxidation from some of the ores which contain these ele­ments. The work related oxidation and solution diffusion behav­iors and the important physical, textural, and mineralogical characteristics of the different ore types. Conceptual-level feasi­bility studies have defined the principal capital and operating cost components of the nitric acid method, sufficient to allow reliable comparisons with other oxidative technologies.

Jan 1, 1996

By William K. Brown

Are the results of an exploration program worth the cost? This is a question I suspect many of you are familiar with and, theoretically at least, it is an easy question to answer. The answer, of course, lies in comparing the future earnings stream the program is expected to generate, to the present value of the cost of carrying it out. While historical costs can be determined without much difficulty, estimating the value of a future earnings stream involves all sorts of assumptions regarding future costs, metal prices, inflation rates and an appropriate discount factor; and in the context in which the question arises, requires additional assumptions about mineral deposits which have yet to be discovered. As a practical matter, this kind of approach isn't likely to produce a very convincing answer; certainly not one convincing enough to satisfy a skeptical audience; nor one likely to temper the illusions of recent converts to mineral exploration, who are convinced that if enough money is spent, profitable discoveries will inevitably follow. Within broad limits, however, I believe it is possible to analyze the costs and results of gold exploration in the U.S.A. over the past 20 odd years in a useful manner. And while such an analysis is imperfect, it will provide some insight into this fascinating subject.

Jan 1, 1983

By William E. Bruce

Percussive drill calibration experiments performed by the Bureau of Mines on two drills are described. The use of a linear velocity transducer to determine piston velocity, blow frequency, and piston stroke length is discussed. Data are presented on the relationships between maximum work rate and feed air pressure. Penetration rates in nine rock types were measured for the same two drills. Physical properties of the nine rock types are presented in tabular and graphical form to show relationships between penetration rates and physical properties. Finally, conclusions are drawn as to the potential use of these data to predict percussive drilling rates.

Jan 1, 1970

By C. A. Rowland

The use of the Bond Work Index to size industrial grinding equipment is well known. Its use to measure grinding efficiency was presented by C.A. Rowland, Jr. at an AIME meeting in 1976. However, due to a bureaucratic error, the paper was never submitted for publication. This metric has nevertheless been adopted by industry as a widely used standard. The purpose of this paper is to re-present and update the application of this tool as a standard for measuring grinding circuit efficiency. Definition ?standard, n. something established for use as a rule or basis of comparison in measuring or judging capacity, content, extent, value, quality, etc.; as standards of weight and measure? (Webster, 1958).

Jan 1, 2008

By James A. Berberick

Research methods to develop an economic model for the determination of regional mineral advantage are discussed. An industrial complex conceptual framework is used to study potential mineral resource outputs of Kansas. A procedure for making a comparative cost analysis of potential outputs for a Kansas-based industrial complex is outlined and illustrated. Methods for estimating aggregate demand and for developing an input-output matrix for a hypothetical limestone complex are explained. The input-output matrix is expressed in physical units. A computer algorithm for converting physical production data and input cost data into total cost per unit of output information is briefly explained and flowcharted. Limitations and usefulness of this procedure in determining regional advantages are surveyed.

Jan 1, 1969

By Jon C. Jenkins

In order to plan the most efficient mine installation, a company should take advantage of all available information and tools. One of the first factors of a coal reserve that needs to be determined as accurately as possible is the quality of coal the mine will have access to during the life of the installation. With the aid of many types of well logs and computor analysis, we are investigating several methods of log correlation to determine such data as moisture, ash, sulphur, and BTU on an in place basis. It may be possible to determine this data more accurately in this manner than by using diamond drill cores for analysis and thus allow for a more profitable mine installation. The production of an underground mine is based on many factors, two of these being roof control and line water, where present either in the roof or coal seam. Using many of the same logs obtained from reserve and active mine areas, we have attempted to determine roof and floor characteristics such as strength, lithology, and moisture properties. Using data obtained from this program, we will make comments on possible length of bolt to be used, possible mining width, and pillar size as they would pertain to these reserves and active mine areas.

Jan 1, 1969

By Alex G. Sciulli

According to recent estimates, nearly 30 percent of the material from underground coal mining in the United States is rejected on the surface as waste. This accumulation of almost three billion tons of coarse and fine coal refuse is primarily from coal cleaning operations. The marketable coal is intermixed with sandstone, clays, shales, and carbonaceous rocks, which must be removed and disposed of in an acceptable manner. The disposal of mineral wastes is a major environmental concern. The most common types of environmental problems associated with coal refuse disposal are acid formation, erosion, and sediment control. Other areas of concern include air and water quality, combustion control, mine sealing, and reclamation. This paper focuses on these topics and attempts to outline special environmental features which can be incorporated into the design and construction of a coal refuse facility. Often these measures can minimize and possibly eliminate the potential environ- mental hazards. It is imperative, however, that these measures be adopted prior to and during construction, because of the relative ease and cost savings compared to post-construction implementation.

Jan 1, 1983

By Vasiliki Founta, Andrew J. Whittle

"This paper describes the development of a 3D finite element model for predicting ground movements caused by construction of 7.1 m diameter twin bored tunnels for the Crossrail project in London using Earth Pressure Balance (EPB) machines. The model uses the commercial FE code, Plaxis 3D, to represent the face pressure, conical shield, grouting process and activation of precast segmental concrete lining systems through a set of boundary conditions that advance through the soil mass along a prescribed trajectory. Soil behavior is described using the Mohr-Coulomb soil model with input parameters calibrated from laboratory element tests. The analyses focus on the performance of the EPB tunneling machines in greenfield conditions beneath Hyde Park, where the tunneling occurs within deep layers of relatively uniform London Clay. The model predictions are in good agreement with surface and sub-surface vertical settlements measured at a well-instrumented section, but tend to overestimate the measured lateral displacements towards the tunnel. Ongoing studies are focused on the role of soil behavior and the approximations in FE model predictions of tunnel-induced ground deformations. Introduction Since their introduction in the 1970’s, closed-face Earth Pressure Balance (EPB) machines have become widely used for soft ground tunnel construction. The EPB design relies on a screw conveyor system to regulate the pressure of the excavated soil/spoil within the head chamber and hence control stability at the face of the machine. One of the key design issues in the application of EPB machines is to establish how control parameters, including the advance rate, face pressure and grouting processes (used to compensate for the tail void at the rear of the shield and to infill gaps between the precast lining rings and surrounding soil) affect and/or control the far-field ground movements. For closed-face systems, short-term deformations are associated with ground losses at the face, overcutting and ploughing of the shield and poor control of grouting in the tail void; while long-term deformations can occur due to consolidation and creep within the surrounding soil (and are closely connected to the seepage boundary conditions;e.g., Laver & Soga, 2012). The control parameters for advancing the EPB machine can have a significant effect on the magnitude and distribution of the far-field deformations. Therefore, analyses of the ground response to tunneling require accurate modeling of the soil stratigraphy and constitutive behavior as well as the construction process. Finite element (FE) methods have been used to simulate tunnel construction since the early 1980s, but only a few studies involved three-dimensional modelling of mechanized tunneling (e.g., Finno and Clough 1985; Bernat and Cambou 1999; Swoboda and Abu-Krisha 1999; Dias et.al. 2000; Melis et.al. 2002; Kasper and Meschke 2004; Möller 2006). In order to get a better understanding of the effect of the construction process and soil properties on the development of the ground deformations more comprehensive models of tunnel excavation and tunnel support are required in order to capture the 3D nature of mechanized tunneling and the effect of construction parameters such as advance rate, face and grout pressure."

Jan 1, 2016

By A. Tarigan

The integration of the ESZ orebody and DOZ orebody resulted in a much larger footprint than the original DOZ Mine shape. The significant change in footprint geometry presented new cave front management challenges, specifically: longer undercut drifts. Using a constant blasting rate, more time is required to complete caving in each drift which ultimately influences the number of active faces at any point in time. The number of manageable active drifts is controlled by the planned square-meters of undercut blasting, lead/lag restrictions and other specific conditions such as the need to blast pre-charged explosives. In early 2008, an evaluation of the existing plan showed that significantly more active undercut drifts and longer cave fronts would occur in the next five years. Difficulties associated with the long cave fronts led to a decision to redesign the caving sequence. Several different boundary options based on operational, geotechnical and ore grade parameters were investigated. This paper describes the issues faced with long cave fronts, the constraints and requirements to effectively manage the caving sequence and the options considered to mitigate this situation.

Jan 1, 2010

By Glenn Melchert, Paul Eger, Jon Wagner, Dave Antonson, John Folman

Current approaches to reclaiming acid generating tailings include permanent water cover or encapsulation with various synthetic liners and/or clay. Although these methods can be effective, some ongoing maintenance will be required in perpetuity to ensure that water levels are adequately maintained or that the integrity of any capping system is protected. The successful creation of wetlands in tailings basins offers the possibility of creating a stable environment for the tailings with minimal maintenance. Acid-generating tailings from a massive zinc sulfide deposit in Winston Lake, Ontario, were placed in small cylindrical tanks to examine the feasibility and effectiveness of creating wetlands and mitigating acid and metal release. Two uncovered controls were established in addition to the five treatments, which were done in duplicate. Each wetland tank was 117 cm in diameter and contained 6 1 cm of tailings. Treatments included 61 cm cover of wetland soil, 61 cm of glacial till, 61 cm of tailings, and two tanks with 71 cm of water. One of the water covers included the aquatic macrophytes: Elodea canadensis, Potamegeton sp., and Ceratophyllum demersum. Cattails (Typha latifolia) were planted in the plots with substrate cover, and the initial water level was set at ten centimeters. The pH within the tailings in the treated tanks generally ranged between 6.0 and 6.5 and zinc concentration ranged from 0.02 to 0.1 mg/L. The drainage from the controls had an average pH of 3.3, and 7,700 mg/L of zinc.

Jan 1, 2000

Horizontal stress is an important factor that contributes to roof failure during a long wall entry development, especially when the immediate roof is weak. In this study, the effects of the three factors, the stress angle between the maximum horizontal stress and entry development, the stress ratio of the maximum to the minimum horizontal stresses, and the sequence of entry development, on the stress distributions in the weak immediate roof of a three-entry system are analyzed using the finite element method, when the horizontal stress is fixed. The results have confirmed that the stress angle has a significant influence on the stress distributions. Generally, the three-entry system is in the worst stress condition when the angle is about 60°_75°. The stress ratio has little effect on the roof stresses. In addition, the sequence of entry development has also little effect on the roof stress for the specific case analyzed.

Jan 1, 1999

By L. E. Mylting

Modern ash handling systems exist in considerable numbers and a great deal of design and operating experience has been accumulated, It is the endeavor of this paper to point to a number of frequently recurring problems, A general appreciation of these problems will be helpful in both design and operation of systems. The light fly ash and the heavy bottom ash present different problems, and each will therefore be treated separately. Fly ash is collected in the ducting from the furnace to the stack and beneath the mechanical and electrostatic dust collectors. The greatest amount of dust is collected beneath the mechanicals and electrostatics. Hoppers are generally provided as integral parts of the collector. Suitable valves and piping are connected to these hoppers for removal of the dust. The size and shape of these hoppers are important factors in determining frequency of handling and the capacity of the system.

Jan 1, 1958

By J. A. Cooper, M. R. Petersen, P. O. Jackson, J. C. Langford

The organic, inorganic, and radiological characteristics of airborne aerosols have been measured as a function of particle size in controlled atmosphere test chambers and operating uranium mines. Concentrations of benzo(a)pyrene in two mines ranged from 26 to 57 ng/m3 of air. The carbon chain length of adsorbed n-alkanes was correlated with particle size. Normal mining activities produced an ore dust aerosol with mass median aerodynamic diameter (MMAD) greater than 2 µm. The elements Na, Al, Si, K, Ca, Ti, V, Fe, and U exhibited elemental ratios similar to bulk ore and had comparable MMAD's. The S, Zn, and Pb were higher in aerosols than bulk ore and were associated with smaller MMAD particulates. Radon daughter particle size distributions were influenced by the kinds of particulates

Jan 1, 1981

By L. J. Jansen

Techniques utilized to incorporate geological data in computer modeling and ore reserve estimation have undergone considerable evolution during the past fifteen years. Computer analysis and evaluation of two precious metal deposits are presented as examples of innovative computer techniques developed at Asarco. The first is a gold deposit occurring in a steeply dipping Pre-Cambrian greenstone sequence. The second is a manto-like manganiferous silver deposit occurring in a relatively flat sequence of Late-Paleozoic sediments. In both deposits, four sub-horizontal zones of geological influence are evaluated.

Jan 1, 1985

By James J. Scott

I welcome this opportunity to speak before the Coal Division of the AIME in such an attractive setting as the Pacific Northwest. With the development of the Centralia project, the Pacific Northwest will have its first major coal-fired thermal electric generating plant. This State has a long history of coal mining that diminished with the passage of coal-fired steamships and locomotives but is now reviving with the growth of electrical power demand. Because this 1,400 row plant is to be supplied with surface-mined coal, it is particularly appropriate that this area be the setting for a talk on factors influencing the growth of surface coal mining in the West. During the course of my talk, I will touch on a number of factors including electric power demand, coal resources, production trends, environmental considerations and trends in State and Federal activities that I feel will influence surface coal mining in the West. Total electric power consumption by the year 2000 is expected to reach 9.4 trillion kilowatt-hours. Predictions of total coal consumption for electric power generation by that year range from a low of 845 million tons to a high of 1,520 million tons, or 2.6 to 4.7 times the amount used for this purpose in 1970.

Jan 1, 1971

By James R. Hindman

Vermiculite is the mineralogical name generally applied to a group of hydrated, trioctahedral ferromagnesian aluminum platty or micaceous silicate minerals. In microscopic particles the mineral as mineral is differentiated from montmorillonite by a higher Si:AI ratio of approximately 3:l and a higher layer charge and higher cation exchange capacities. Commercial vermiculite, the vermiculite which is mined, beneficiated, and discussed in this chapter, is an important industrial mineral which is formed by the alteration of macroscopic particles of biotite and iron-bearing phlogopite. In natural form it has the size and shape of mica, while possessing the ion exchangeable properties of zeolites and some clays. Within the internal structure of vermiculite lie water molecules, which when rapidly heated to high temperature, transform into steam causing the vermiculite particles to increase in volume. This process of thermal exfoliation produces a lightweight product which finds use in various construction products, agriculture, horticulture, and other industrial applications. In exfoliated form it has the low density and biological inertness of expanded perlite, while maintaining a chemically active surface. Most of the uses of vermiculite are for the thermally exfoliated material. In addition, the cation exchange potential of vermiculite and its layer-silicate structure are properties which can be used as the basis for numerous products including intumescent coatings and gaskets, inorganic films, and the treatment of nuclear and other toxic waste. When chemically and physically modified, it possesses some properties common to organoclays and synthetic compounds. In high purity concentrates and manufactured products, these properties can be altered and optimized in applications to produce superior performance. GEOLOGY Mineralogy Vermiculite was first described as a mineral by Thomas H. Webb in 1824. Webb believed vermiculite to be a variety of talc and described its diagnostic property of thermal exfoliation thusly: "If subjected to the flame of a blowpipe, or that of a common lamp, it expands and shoots out into a variety of fanciful forms, resembling most generally small worms having the vermicular motion exact." Observing that with one exception, all commercial vermiculite has formed by the alteration of iron-bearing phlogopite, a simple definition of vermiculite might be the alteration product of trioctahedral micas, macroscopic particles of which display marked exfoliation when heated rapidly to temperatures above 374°C (the critical temperature of water). The first vermiculite described was found near Worcester, MA, but it was later pointed out by Brush (1866) that vermiculite had been known for some time in Japan as a children's novelty. Because the techniques for mineral analysis were somewhat primitive com- pared to those routinely available today, and because the structure and crystal chemistry of the micas and related minerals were not widely understood, the early literature generated at least 20 "new" minerals which were nothing more than variations in the color and chemistry displayed by vermiculite. Trade names such as Dugarlite, Mandolitem, Strong-LiteTM, and Zonolitem are sometimes used to denote commercial vermiculite, thermally exfoliated vermiculite and their products. Vermiculite particles resemble mica and vary in color from colorless through tan and green to black, depending on the chemical composition. Most physical and optical properties are close to those of biotite, with perfect basal cleavage, hardness between 1.5 and 2.5 Mohs, and specific gravity between 2.2 to 2.8. Fine-sized particles will feel talcose, especially when wet. However, for commercial vermiculite the diagnostic test is that of thermal exfoliation. Vermiculite can display a wide range of compositions, depending on the composition of the original mica and the change of chemistry during weathering and ion exchange. Chemical data for some commercial vermiculites are given in [Table 1]. There are numerous analyses for vermiculite given in the literature, and the analyses of vermiculites from commercial deposits will fall within the range indicated by the average analysis in the table. Many analyses separate the adsorbed water (H2OP) from crystalline water and water as hydroxyl (H20+). The basis of separation of adsorbed water is generally considered to be 100°C. However, hydrate water within the vermiculite interlayer begins to be lost at 75°C and lower. Therefore, measured water content and loss on ignition are combined in the table as H20[total].

Jan 1, 1994

By V

"Recent regulations, as well as a general aversion to central dust collectors within the Powder River Basin Coal user’s community, have created a need for an alternate method for eliminating airborne dust. This paper addresses the capital expenditure as well as the cost of ownership of an integrated point source air cleaning system in comparison to a central collection system. This assessment was conducted by comparing the cost to purchase and operate a central dust collection system and integrated air cleaner system on a typical multiple transfer point application. The central dust collector consists of a negative pressure blower, a series of filter bags, a collection hopper, a screw conveyor to place collected material back into the material stream, and a series of ducts to pull air and dust from individual pickup points. The point specific integrated air cleaners consists of a negative pressure blower to pull dust and air from an application point through a bag-less filter media located at the application point. The agglomerated material is then redeposited into the material stream at point of use without the need for ducting or a central material hopper. The assessment yielded a 54% reduction in capital expenditure and a 26% reduction in operating costs for the same application when using individual dust filters as opposed to a central system. In addition to the lowered cost, there are reductions in risk associated with the elimination of ductwork and the central containment enclosure for collected explosive dust. By the conclusion of this paper, the reader will have a better understanding of the quantifiable differences between a central dust collection system and a set integrated air cleaner systems. BACKGROUND Spillage has always been a problem in the bulk solids handling industry. As long as there have been conveyors, there has been spillage. Spillage is material that falls off a conveyor belt and creates a hazard in the environment around a conveyor belt."

Jan 1, 2016

By M. Niec

Lignite deposits in Poland occur within clastic Tertiary series at the depth suitable for opencast mining. Aboundant aquifers with the good quality waters that should be protected against contamination or depletion often accompany them. Landscape and underground water protection are the main regional environ-mental factors that limit the possibility of exploration and mining; presented on map of lignite bearing series distribution allow to delimit areas "free" for exploration and mining and areas where some limitations can be met up to no admittance of any industrial activity.

Jan 1, 1994

By John Jonkman

The cost of equipment maintenance is the largest single expense at many mines and processing plants. It is not unusual for a maintenance and repair budget to be larger than 50% of the punt's total budget. Generally, in the mining industry, 400-60% of the work force in a plant reports to the maintenance department. Studies have shown that many plant maintenance workers are only 33 to 40% productive, working 2.6 to 3.7 hours of every 8-hour day. In recent years, many companies have begun to recognize that- productivity improvements and cost reductions can he achieved by upgrading maintenance methods. This paper discusses ten common causes of low maintenance productivity and how recent advancements in computing technology can be utilized to address these causes for low productivity.

Jan 1, 1986